GE FUF14S, FUF21S, FUF12S User Manual
ge.com
Owner’s Manual &
Installation Instructions
Food Freezers
297252000 162D9627P010 49-60567-1 09-08 JR
Safety Information . . . . . . . . . . . . 2–4
Operating Instructions
Care and Cleaning . . . . . . . . . . . . . . .10–12
Defrosting Instructions
(for Manual Defrost Models) . . . . . . . . . . .9
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Starting the Freezer . . . . . . . . . . . . . . . . . . .5
Installation Instructions
Preparing to Install the Freezer . . . . . . 13
Troubleshooting Tips . . . . . . . .14–16
Normal Operating
Characteristics . . . . . . . . . . . . . . . . . . . . . . .14
Consumer Support
Consumer Support . . . . . . . . . Back Cover
Production Registration for
Customers in Canada . . . . . . . . . . . . 19, 20
Production Registration for
Customers in the U.S. . . . . . . . . . . . . 17, 18
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Model number: _____________________
Serial number: _____________________
You can find them on a plate either on
the upper left wall inside the freezer
(Upright models) or on the left exterior
wall (Chest models).
La section française commence à la page 25
La sección en español empieza en la página 43
Congelador
de alimentos
Manual del propietario
y instalación
Congélateur
d’aliments
Manuel d’utilisation
et d’installation
Upright—Manual Defrost
Models:
FUM13, FUM14, FUM17,
FUM21
Upright—No-Frost Models:
FUF12, FUF12S, FUF14,
FUF14S, FUF17, FUF17C,
FUF17S, FUF20, FUF20S,
FUF21, FUF21S
Chest—Manual Defrost Models:
FCM5, FCM7, FCM9, FCM15,
FCM20, FCM25
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
WARNING!
Use this appliance only for its intended purpose as described in this Owner’s Manual.
SAFETY PRECAUTIONS
When using electrical appliances, basic safety precautions should be followed, including the following:
■
■This freezer must be properly installed and located
in accordance with the Installation Instructions
before it is used.
■
■Do not allow children to climb, stand or hang
on the shelves in the freezer. They could damage
the freezer and seriously injure themselves.
■
■After your freezer is in operation, do not touch the
cold surfaces, particularly when hands are damp
or wet. Skin may stick to these extremely cold
surfaces.
■
■Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance.
■
■Unplug the freezer before cleaning, making repairs
or changing the light bulb.
NOTE: We strongly recommend that any servicing
be performed by a qualified individual.
■
■Turning the control to the OFF position does not
remove power to the light circuit on models with
interior light.
■
■Do not refreeze frozen foods which have
thawed completely.
■
■The maximum amount of food your freezer is
designed to freeze at one time is approximately
3 pounds (1.5 kg) per cubic foot of freezer capacity.
In normal position, your freezer’s temperature
control will maintain sufficiently
low temperatures in the freezer to freeze
recommended quantities of food.
■
■Caution should be used when removing the door of
a freezer. Particular caution should be used when
removing the lid of a Chest freezer, as most Chest
freezer lids are under spring tension. Contact the
manufacturer’s representative for a method of safe
removal.
Consumer Support
Troubleshooting Tips
Operating Instructions
Safety Instructions
Installation
Instructions
2
3
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions
Installation
Instructions
USE OF EXTENSION CORDS
Because of potential safety hazards under certain conditions, we strongly recommend against the use
of an extension cord.
However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed (in the United
States) or a CSA-listed (in Canada), 3-wire grounding type appliance extension cord having a grounding type
plug and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 120 volts.
DANGER! RISK OF CHILD ENTRAPMENT
PROPER DISPOSAL OF THE FREEZER
When using electrical appliances, basic safety precautions should be followed, including the following:
Child entrapment and suffocation are not problems
of the past. Junked or abandoned refrigerators and
freezers are still dangerous…even if they will sit for
“just a few days.” If you are getting rid of your old
refrigerator or freezer, please follow the instructions
below to help prevent accidents.
Before You Throw Away Your Old
Refrigerator or Freezer:
■Take off the doors.
■Leave the shelves in place so that children may not
easily climb inside.
Refrigerants
All refrigeration products contain refrigerants, which
under federal law must be removed prior to product
disposal. If you are getting rid of an old refrigeration
product, check with the company handling the
disposal about what to do.
ge.com
4
Consumer Support
Troubleshooting Tips
Installation
Instructions
Safety Instructions
Operating Instructions
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
WARNING!
HOW TO CONNECT ELECTRICITY
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.
For personal safety, this appliance must be properly grounded.
The power cord of this appliance is equipped with
a 3-prong (grounding) plug which mates with a
standard 3-prong (grounding) wall outlet to minimize
the possibility of electric shock hazard from this
appliance.
Have the wall outlet and circuit checked by a qualified
electrician to make sure the outlet is properly
grounded.
If the outlet is a standard 2-prong wall outlet, it is
your personal responsibility and obligation to have
it replaced with a properly grounded 3-prong wall
outlet.
The freezer should always be plugged into its own
individual electrical outlet which has a voltage rating
that matches the rating plate.
This provides the best performance and also prevents
overloading house wiring circuits which could cause a
fire hazard from overheated wires.
Never unplug your freezer by pulling on the power
cord. Always grip plug firmly and pull straight out
from the outlet.
Repair or replace immediately all power cords that
have become frayed or otherwise damaged. Do not
use a cord that shows cracks or abrasion damage
along its length or at either end.
When moving the freezer away from the wall, be
careful not to roll over or damage the power cord.
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
SAVE THESE INSTRUCTIONS
This electronic temperature control is located on
the front of the freezer door. The temperature is
factory-preset to provide satisfactory food
storage temperatures. To adjust the temperature
setting, press Colder to decrease temperatures
and Warmer to increase temperatures. Allow
several hours for the temperature to stabilize
between adjustments.
To turn the freezer off, press Warmer until the
display reads “0.” To turn the freezer on, press
Colder until the display shows “4” or the desired
setting.
To lock the controls, press Alarm Reset for
3 seconds. The display will read “L.” To unlock
the controls, press Alarm Reset for 3 seconds.
The display will read “U” and then display
the current temperature.
This electronic control has a temperature
alarm feature. If the inside temperature
exceeds 23°F. An alarm will sound if the
freezer temperature reaches unsafe levels.
The alarm operates on household electricity.
If the power fails, the alarm will not perform.
When the freezer is initially plugged in, the
red Hi Temp light will come on and a buzzer
will sound. The indicator light will stay on until
the freezer temperature reaches 23°F or
below. To silence the buzzer, push Alarm
Reset. If the temperature in the freezer goes
above 23°F for any reason, the Hi Temp light
will come on and the buzzer will sound every
hour until the temperature is below 23°F. To
silence the buzzer, push Alarm Reset.
If an “E” appears on the display, contact your
authorized service technician for repair. The
freezer will continue to run until serviced.
Consumer SupportTroubleshooting Tips
Operating Instructions
Safety Instructions
Installation
Instructions
About the operation of your freezer. ge.com
Starting the Freezer
Clean the inside of the freezer with a mild solution of baking soda and water (see Care and Cleaning).
Connect cord to power outlet.
On models with a Temperature Monitor or High-Temp Alarm Switch, set the switch to the OFF position.
Make sure the temperature control is set at 4.
Allow freezer to operate for at least four hours before placing food inside.
On models with a Temperature Monitor or High-Temp Alarm Switch, set the switch to the ON position.
6
5
4
3
2
1
5
Electromechanical Temperature Control (Chest and some Upright models)
The electromechanical temperature control
is preset to give satisfactory food storage
temperatures. It is adjustable to provide a
range of temperatures. Allow several hours
for the temperature to stabilize between
adjustments.
The electromechanical temperature control is
on the outside left on the chest models and
inside the freezer on upright models.
Temperature Control
For safe food storage, allow 4 hours for the
freezer to cool down completely. The freezer
will run continuously for the first several
hours. Foods that are already frozen may be
placed in the freezer after the first few hours
of operation. Unfrozen food should NOT be
placed in the freezer until it has operated for
4 hours. Allow several hours after each onestep adjustment for the freezer temperature
to stabilize.
When loading the freezer, freeze only
3 pounds of fresh food per cubic foot of
space at a time. Distribute packages evenly
throughout the freezer. It is not necessary to
turn the control knob to a colder setting while
freezing food.
Turning the control to OFF stops the cooling
process but does not shut off power to the
freezer.
Electronic Temperature Control (some Upright Frost-Free models)
6
This feature is designed to provide a warning
if the inside temperature reaches an unsafe
level. The Temp Alarm feature operates on
household electricity. It will not function if
household electricity is interrupted.
When the freezer is initially plugged in, the
red Temp Alarm indicator light blinks. The
indicator light will continue to blink until the
freezer has reached a safe freezing
temperature. If a malfunction causes an
unsafe temperature inside the freezer, the
red light will blink and the buzzer will sound.
To silence the buzzer, press the ALARM OFF
button. The indicator light will continue to
blink until a safe freezing temperature is
again reached. If the problem is not solved
within twelve (12) hours, the buzzer will turn
on again. If the ALARM OFF button is not
pressed, the buzzer will turn itself off
automatically after 48 hours, but the red
Temp Alarm light will continue to blink.
High-Temp Alarm Switch (on some models)
An alarm will sound if the freezer
temperature reaches unsafe levels. The
alarm operates on household electricity. If
the power fails, the alarm will not perform.
An ON/OFF switch allows the temperature
alarm to be deactivated if desired. The freezer
is shipped with the switch in the OFF position.
After the freezer has run long enough to
lower the temperature, you may set the
switch to the ON position.
CAUTION: Adding more than 3 pounds
(1.5 kg) of warm food per cubic foot of
freezer capacity can trigger the alarm.
To activate the alarm, set the switch to the
ON position.
To deactivate the alarm, set the switch to
the OFF position.
Convertible Freezer/Refrigerator (some Upright Frost-Free models)
The convertible model can operate as either a
refrigerator or a freezer. The selection is made
using the switch at the back of the unit
marked F and R. With the switch in the F
position, the freezer controls below this switch
and to the left become active. With the switch
in the R position, the refrigerator controls
below this switch and to the right become
active. Placing the switch in the middle
position will turn off the unit completely and
will disable all cooling functions.
The temperature on this model is preset. To
adjust the temperature, push the UP button
for warmer and the DOWN button for cooler
temperatures. Allow several hours for the
temperature to stabilize between
adjustments.
When in the refrigerator mode, the Freeze
Control Feature maintains proper interior
refrigerator temperature even if placed in an
area where the temperature is 10°F (-12°C).
Located on back of lid.
Electronic Temperature Alarm (some Electronic Chest models)
Indicator
Lights
On/Off
Switch
Consumer Support
Troubleshooting Tips
Installation
Instructions
Safety Instructions
Operating Instructions
About the operation of your freezer.
ge.com
Freezer Shelves (on some models)
The spacers (on some models) are used to
secure the shelves during shipping. Remove
and discard the spacers.
Small objects are a choke hazard to
children.
Key-Ejecting Lock (on some models)
The key for the spring-loaded lock is
automatically ejected–key will not remain in
lock in either the open or closed position.
Keep the key out of reach of children and
away from the freezer.
Power-On Light (on some models)
The Power-On Light indicates that the freezer
is properly connected to the electrical power.
The light glows even when the temperature
control is turned off.
Tilt-Out Shelf (some Upright models)
This shelf is located inside on the freezer door
and provides additional storage space. To
access an item, tilt the top of the “basket”
shelf down.
Slide-Out Basket (some Upright models)
A slide-out basket provides separate storage
space for items that are difficult to store on
shelves. It is located at the bottom of the
freezer. To remove this basket, pull out and
lift up.
Interior Light
The interior light comes on when the freezer
door is opened. To replace the bulb, set the
temperature control to OFF and unplug
the electrical cord. Replace the bulb by
unscrewing it from the fixture. Replace
with the same size and wattage.
Adjustable Shelves (Upright models)
The adjustable shelves can be moved to
different levels within the freezer. To move the
shelf, grasp the shelf and push to either the
right or the left to disengage the ends of the
shelf from placement holes in the freezer. Tilt
the shelf to release the other side. To install
the shelf, reverse these directions.
Some models will have glass shelves and
some models will have wire shelves.
Upright Models
Wire Shelf Placement Holes
Glass Shelf Placement Holes
Consumer SupportTroubleshooting Tips
Operating Instructions
Safety Instructions
Installation
Instructions
7
8
Consumer Support
Troubleshooting Tips
Installation
Instructions
Safety Instructions
Operating Instructions
About the operation of your freezer.
Soft Freeze Zone (some Upright models)
The Soft Freeze Zone is specifically for foods
such as ice cream. It is designed to maintain
a higher temperature than the rest of the
freezer.
Basket Divider (some Upright models)
Organize your freezer basket by using
the basket dividers supplied. To change
the location, rotate the divider in a
counterclockwise direction and pull up until it
is free from the basket. Align the center of the
divider with the center of the line in the
bottom of the basket as shown in the figure.
Rotate the divider clockwise until it snaps into
place.
Crispers (some Upright models)
The crispers are designed for storing fruits,
vegetables and other fresh produce. Items
should be washed and drained well before
placing in the crisper drawers.
One of the crisper drawers comes equipped
with a Humidity Control. This allows you to
control the humidity within that crisper. This
can extend the life of fresh vegetables that
keep best in high humidity.
Adjustable Door Bins (some Upright models)
The adjustable door bins provide flexible
storage space. The number of bins varies by
model.
Wire Shelf Bookend (some Upright models)
Use these handy bookends to keep various
boxed items stored neatly in your freezer.
To adjust the location, simply unsnap the
bookend from the wire shelf and snap into
the next desired location.
Lo
Hi
In most climates, defrosting will be necessary
only about twice a year.
To have your freezer operate most
efficiently, do not permit more than 1/2 ″
(13 mm) of frost to accumulate on the
shelves.
To remove frost, scrape with a plastic or
wood spatula or scraper.
Do not use an ice pick or sharp-edged
instrument as it may damage or scratch
the freezer.
Do not use any electrical device in
defrosting your freezer.
For Complete Defrosting
Turn the temperature control to OFF and
unplug the freezer.
Remove all food and place it in
corrugated boxes, insulated bags, picnic
coolers, etc. Use towels and newspapers
for insulation as needed.
With the door/lid open, use pans of
hot water to speed loosening of frost.
Remove large pieces before they melt.
On models without a defrost drain, place
towels or newspapers on the freezer
bottom to catch the frost. The frost will
loosen and fall. Remove towels and/or
newspapers.
a. Some Upright models have a hose
adapter and a drain hose behind the
base grille which carry the defrost
water out from the freezer. Remove
the base grille; then remove the drain
plug and let the defrost water drain
into a pan.
To remove the base grille (on some
models), remove the two Phillips-head
screws and pull the grille away from
the freezer.
b. Some Chest models have a defrost
water drain at the front and a hose
adapter that is packaged in a bag in
the bottom of the freezer. Remove
the drain cap on the front of the
freezer, insert the hose connector
and attach the hose. Remove the
drain plug inside the cabinet.
NOTE: Water may drip from the
back flange of the lid cover during
defrosting. This is normal. Ice builds
up in the lid insulation when the lid is
open for adding or removing food,
and melts during the defrosting
operation.
Sponge excess water from the bottom
of the freezer as it collects to prevent
overflowing.
After defrosting, clean the inside of the
freezer (see Care and Cleaning).
a. On Upright models, be sure to replace
the drain plug and return the drain
tube to its position. Replace the
base grille.
b. On Chest models, replace the drain
plug inside the cabinet and the cap
on the defrost drain. Fold over and
dry the gasket on the hinge side of
the lid.
Plug in the freezer. Return the
temperature control to its previous
position and return food to the freezer.
8
7
6
5
4
3
2
1
Drain Hose
9
Defrosting instructions. (for Manual Defrost models) ge.com
Consumer SupportTroubleshooting Tips
Operating Instructions
Safety Instructions
Installation
Instructions
Consumer Support
Troubleshooting Tips
Installation
Instructions
Safety Instructions
Operating Instructions
Care and cleaning of the freezer.
Cleaning Your Freezer
■Outside. Protect the paint finish. The finish
on the outside of the freezer is a high
quality, baked-on paint finish. With proper
care, it will stay new-looking and rust-free
for years. Apply a coat of appliance polish
wax when the freezer is new and then at
least twice a year. Appliance polish wax
also works well to remove tape residue
from freezer surfaces.
Keep the finish clean. Wipe with a clean
cloth lightly dampened with appliance
polish wax or mild liquid dishwashing
detergent. Dry and polish with a clean, soft
cloth. Do not wipe the freezer with a soiled
dishwashing cloth or wet towel. Do not use
scouring pads, powdered cleaners, bleach,
or cleaners containing bleach.
CAUTION: Care should be taken in moving
the freezer away from the wall. All types of
floor coverings can be damaged,
particularly cushioned coverings and those
with embossed surfaces.
■Inside. Clean the inside of your freezer at
least once a year. We recommend that the
freezer be unplugged before cleaning. If this
is not practical, wring excess moisture out
of sponge or cloth when cleaning in the
vicinity of switches, lights or controls.
Use warm water and baking soda
solution–about a tablespoon of baking
soda to a quart of water. Rinse thoroughly
with water and wipe dry. Do not use
cleaning powders or other abrasive
cleaners. DO NOT wash removable parts in
a dishwasher.
An open box of baking soda in the freezer
will absorb stale freezer odors. Change the
box every three months.
CAUTION: Damp objects stick to cold metal
surfaces. DO NOT touch interior metal
surfaces with wet or damp hands.
CAUTION: Freezer must be unplugged to
avoid electrical hazard from power source
when defrosting unit.
Some upright freezers are frost-free and
defrost automatically, but should be
cleaned occasionally.
10
No Defrosting (on No-Frost models)
You never have to defrost your new No-Frost
freezer. It has been pre-set at the factory to
defrost itself automatically.
Package labels always remain clearly legible,
and packages will remain easy to separate
and remove.
During defrosting, a slight noise may be
noticed if the door is opened while the freezer
is in the automatic defrosting cycle.
11
ge.com
Consumer SupportTroubleshooting Tips
Operating Instructions
Safety Instructions
Installation
Instructions
To Remove the Freezer Door (on Non-Electronic Control Upright models)
Remove the plastic hinge cover by either
lifting it off or folding it back (depending
on model).
Remove the screws holding the hinge
to the top of the cabinet using a
screwdriver, 5/16″ socket driver or wrench
(depending on model).
Remove the top hinge from the cabinet
and lift the door up and off the lower
hinge pin. Set the door aside.
Remove the two screws from the bottom
hinge.
To replace the doors, reverse the order of the
above instructions.
CAUTION: It is very important that all hinge
screws are securely tightened to ensure a
secure assembly and prevent hinge slippage.
4
3
2
1
(on some models)
Hinge
Screws
Top Hinge
Plastic Hinge
Cover
Lid Removal (on Chest models)
See lid removal instructions on either the
back of the cabinet or the hinge label.
To Remove the Freezer Door (on Electronic Control Upright models)
The hinge screws are tamperproof.
Please have an authorized service
technician remove the door.
Care and cleaning of the freezer.
Preparing for Vacation
To maintain freezer in operation during
vacations, be sure your house power is not
turned off. For sure protection of freezer
contents, you may want to ask a neighbor
to check the power supply and freezer
operation every 48 hours.
For extended vacations or absences, you
may prefer to move your frozen foods to a
storage locker temporarily. If your freezer is
to be left empty, disconnect power cord plug
from wall outlet. To prevent formation of
odors, place open box of baking soda in
freezer and leave freezer door/lid open.
When the freezer is not operating, it can be
left in an unheated house or room without
damage to cabinet or mechanism.
Preparing to Move
Disconnect the power cord plug from the wall
outlet. Remove foods, defrost (on Manual
Defrost models) and clean the freezer.
Secure all loose items such as grille and
shelves by taping them securely in place
to prevent damage.
Be sure freezer stays in upright position
during actual moving and in van. The
freezer must be secured in van to prevent
movement. Protect outside of freezer with
blanket.
In Case of Extended Power Failure
■Keep freezer door/lid closed. Your freezer
will keep food frozen for 24 hours provided
warm air is not admitted.
■If freezer is out of operation for 24 hours or
more, add dry ice. Leave ice in large pieces.
Add more ice as required.
WARNING: Handling of dry ice can cause
freezing of the hands—gloves or other
protection is recommended.
■If dry ice is not available, move food to a
frozen food locker temporarily—until power
is restored.
■ The freezer should
be located in the
coolest area of the
room, away from
heat-producing
appliances or
heating ducts, and
out of direct sunlight.
■Let hot foods cool to room temperature
before placing in the freezer. Overloading
the freezer forces the compressor to run
longer. Foods that freeze too slowly may
lose quality or spoil.
■Be sure to wrap foods properly, and wipe
containers dry before placing them in the
freezer. This cuts down on frost buildup
inside the freezer.
■Freezer shelves should not be lined with
aluminum foil, wax paper or paper
toweling. Liners interfere with cold air
circulation, making the freezer less
efficient.
■Organize and label food to reduce door
openings and extended searches. Remove
as many items as needed at one time, and
close the door as soon as possible.
Consumer Support
Troubleshooting Tips
Installation
Instructions
Safety Instructions
Operating Instructions
12
Preparing to install the freezer. ge.com
Read these instructions completely and carefully.
Freezer Location
Your freezer should be conveniently located for
day-to-day use in a dry, well-ventilated room.
Do not install the freezer where the temperature will
go below 0°F or above 110°F, because it will not
maintain proper temperatures.
Be sure to install your freezer on a floor strong
enough to support it when it is fully loaded.
The freezer must be solidly positioned on the floor
if it is to function at its best. Shims may be used to
accomplish this wherever the floor is too uneven.
If the place selected for the freezer is damp or moist,
place 2 X 4’s (51 mm X 102 mm) under its entire
length to ensure adequate support.
Clearances
On all models, allow 3″ (76 mm) on top, back and
sides for proper air circulation.
Adjustable Legs (on Upright models)
Legs at the front corners of the freezer should
be set so the freezer is firmly positioned on
the floor, and the front is raised just enough
so the door closes easily when opened about
halfway.
Turn right
to lower
Turn left
to raise
Unit Loading (on Upright models)
CAUTION: To allow the door to close and seal
properly, DO NOT let food packages extend
past the front of the shelves.
Level Freezer
Upright Models:
Discard crate screws and wood base. Use
a carpenter’s level to level the freezer from
back to front. Adjust the plastic leveling feet
in front 1/2 bubble higher so the door closes
easily when left open.
Chest Models:
If needed, add metal or wood shims between
foot pads and floor.
Consumer SupportTroubleshooting Tips
Operating Instructions
Safety Instructions
Installation
Instructions
13
14
Before you call for service…
Troubleshooting Tips
Save time and money! Review the charts on the following
pages first and you may not need to call for service.
Problem Possible Causes What To Do
Freezer does not Temperature control • Move the control to a temperature setting.
operate or Power-On in OFF position.
Light is not on
Freezer is unplugged. • Push the plug completely into the outlet.
The fuse is blown/circuit •Replace fuse or reset the breaker.
breaker is tripped.
Freezer starts/stops Door/lid left open. • Check to see if package is holding door/lid open.
too frequently
Too frequent or too long
door/lid openings.
Temperature control •See About the operation of your freezer.
set too cold.
Freezer operates Door/lid left open. • Check to see if package is holding door/lid open.
too long
Too frequent or too long
door/lid openings.
Temperature control •See About the operation of your freezer.
set too cold.
Inadequate air circulation •See Preparing to install the freezer.
space around cabinet.
Room or outside weather is hot. •It’s normal for the freezer to work harder under these
conditions.
Freezer has been disconnected •It takes 4 hours for the freezer to cool down completely.
recently for a period of time.
Large amounts of warm or hot •Warm food will cause the freezer to run more until the
food have been stored recently. desired temperature is reached.
Normal operating characteristics.
These things are normal and
do not indicate a need for service.
■A warm cabinet exterior as the refrigeration system transfers heat from the inside to the outside through the
exterior cabinet walls.
■The sound of the high-efficiency compressor motor.
■On No-Frost models, the sound of water dripping as it melts from the evaporator and escapes to the drain pan
during defrost cycle.
■On No-Frost models, the sound of the fan circulating air within the interior of the cabinet providing a consistent
temperature throughout.
Consumer Support
Troubleshooting Tips
Installation
Instructions
Safety Instructions
Operating Instructions
ge.com
Problem Possible Causes What To Do
Noisy operation Floor may be weak, causing • Placing 2 X 4’s (51 mm X 102 mm) under the length of
or cabinet vibrates freezer to vibrate when the freezer will help support it and may reduce vibration.
compressor is on.
Cabinet is not positioned •Adjust legs (on Upright models). See Preparing to
solidly on floor. install the freezer. Or use shims for uneven floor.
Freezer is touching the wall. •Level freezer or move slightly. See Level Freezers.
Freezer temperature Door/lid left open. • Check to see if package is holding door/lid open.
too warm
Too frequent or too long
door/lid openings.
Temperature control is set •Turn control to a colder setting. Allow several hours for
too warm. the temperature to stabilize.
Large amounts of water or hot food
•Wait until the freezer has had a chance to reach its
may have been stored recently. selected temperature.
Freezer has been disconnected •Freezer requires 4 hours to cool down completely.
recently.
Foods defrosting Temperature control • Move the control to a temperature setting.
in OFF position.
Freezer is unplugged. • Push the plug completely into the outlet.
The fuse is blown/circuit •Replace fuse or reset the breaker.
breaker is tripped.
Door/lid left open. • Check to see if package is holding door/lid open.
Too frequent or too long
door/lid openings.
Freezer temperature Temperature control •See About the operation of your freezer.
too cold set too cold.
Moisture forms on Not unusual during •Wipe surface dry.
outside of cabinet periods of high humidity.
Door may not be seating properly, •See Preparing to install the freezer.
causing cold air from inside the
freezer to meet warm moist air
from the outside.
Interior light does No power at outlet. • Replace fuse or reset the breaker.
not work
Freezer is unplugged. • Push the plug completely into the outlet.
(on some models)
Light bulb burned out. •Replace bulb.
Door/lid won’t fully Legs need adjusting. • See Preparing to install the freezer.
close by itself
Package holding door/lid open.
Slow starting time Built-in overload protection.
after being off
Excessive frost Door/lid left open. •Check to see if package is holding door/lid open.
buildup
Too frequent or too long
door/lid openings.
Not unusual during
periods of high humidity.
Consumer SupportTroubleshooting Tips
Operating Instructions
Safety Instructions
Installation
Instructions
15
16
Consumer Support
Troubleshooting Tips
Installation
Instructions
Safety Instructions
Operating Instructions
Before you call for service…
Problem Possible Causes What To Do
Freezer external surface The external freezer walls can be •This is normal while the compressor works to transfer
temperature is warm as much as 30°F warmer than heat from inside the freezer cabinet.
room temperature.
Louder sound levels Modern freezers have increased •This is normal. When the surrounding noise level is low,
whenever freezer is on storage capacity and more stable you might hear the compressor running while it cools
temperatures. They require a the interior.
high-efficiency compressor.
Longer sound levels Freezer operates at higher •This is normal. Sound will level off or disappear as
when compressor pressures during the start of freezer continues to run.
comes on the ON cycle.
Popping or cracking sound
Metal parts undergo expansion and
•This is normal. Sound will level off or disappear as
when compressor comes on
contraction, as in hot water pipes. freezer continues to run.
Bubbling or gurgling
Refrigerant (used to cool freezer) is
•This is normal.
sound, like boiling water circulating throughout the system.
Moisture forms on inside Weather is hot and humid, which • This is normal.
freezer walls increases internal rate of frost
buildup.
Door may not be seating properly. • See Preparing to install the freezer.
Door is kept open too long, or is •Open the door less often.
opened too frequently.
Odors in freezer Interior needs to be cleaned. • Clean interior with sponge, warm water and baking soda.
Foods with strong odors are in • Cover the food tightly.
the freezer.
17
General Electric Company
Warranty Registration Department
P.O. Box 32150
Louisville, KY 40232-2150
GE Service Protection Plus
™
GE, a name recognized worldwide for quality and dependability together with Assurant Solutions, offers you
Service Protection Plus
™
—comprehensive protection on your appliances.*
Benefits Include:
• Prompt, reliable service from GE Authorized Servicers
• Convenient hours designed to suit your busy schedule
• Quality replacement parts
• The dependability of GE, a name recognized and trusted worldwide
• Ask about our interest-free payment plans
With Service Protection Plus you can expect:
• An extended service plan that limits unexpected repair bills
• Service coverage for most major brands
• Unlimited service calls for the length of your contract, or credit toward a replacement product
• Service coverage for covered operating parts and labor on appliances and home electronics that fail during normal single family
household use
• Your satisfaction is our goal. We strive to provide you with excellent service in a professional and timely manner.
Place your confidence in GE and call us in the U.S. toll-free at 1.800.626.2224 for more information.
*Most brands covered up to 15 years old in the continental U.S.
SPP is a trademark of General Electric Company.
Please place in envelope and mail to:
✁
Cut here
Consumer Product Ownership Registration
Important
Mail
Today!
GE Consumer & Industrial
Appliances
General Electric Company
Louisville, KY 40225
ge.com
First
Name
Mr. ■■ Ms. ■■ Mrs. ■■ Miss ■■
Street
Address
City
State
Date Placed
In Use
Month
Day
Year
Zip
Code
Apt. #
Last
Name
Phone
Number
_
_
Consumer Product Ownership Registration
Dear Customer:
Thank you for purchasing our product and thank you for placing your confidence in us.
We are proud to have you as a customer!
Follow these three steps to protect your new appliance investment:
Important: If you did not get a registration card with your
product, detach and return the form below to
ensure that your product is registered, or register
online at www.ge.com.
1
23
Model Number Serial Number
✁
Cut here
Complete and mail
your Consumer
Product Ownership
Registration today.
Have the peace of
mind of knowing we
can contact you in
the unlikely event of
a
safety modification.
After mailing the
registration below,
store this document
in a safe place. It
contains information
you will need should
you require service.
Our service number is
800.GE.CARES
(800.432.2737).
Read your Owner’s
Manual carefully.
It will help you
operate your new
appliance properly.
Model Number Serial Number
E-mail Address*
18
* Please provide your e-mail address to receive, via e-mail, discounts, special offers and other important
communications from GE Appliances (GEA).
■■ Check here if you do not want to receive communications from GEA’s carefully selected partners.
FAILURE TO COMPLETE AND RETURN THIS CARD DOES NOT DIMINISH YOUR WARRANTY RIGHTS.
For information about GEA’s privacy and data usage policy, go to www.ge.com and click on “Privacy
Policy” or call 800.626.2224.
Loading...