GE DBLR333EG7WW, DBSR463EG7WW, DBXR300EG6WS, DBXR463EG0CC, DBXR463EG0WW Installation Guide

nstallati
nst cti

Questions on Installation? Call" 1-800-GECARES (US)

lectric

or Visit our Web site at: www.GEAppliances.com (US)

Drye

BEFOREYOU BEGIN

Read these instructions completely and

carefully.

e

IMFORTANT- S.,,ethese

instructions fbr local inspector's use.

"IMPORTANT- Obse,,,e

all governingcodes and ordinances°

* Note to Installer- Be sure to leave these

instructions with the custotner.

* Note to Customer - Keep these instruc>

ions with your Use and Care Book for
furore reference.

* Before the old dryer is removed flom

service or discarded, remove the d_Ter
door.

* Service infbrmation and the wiring dia-

gram are located in the control console.

* Do not allow children on or in the appli-

ance. Close supe_wision of children is
necessa_ T when the appliance is used

near children.

* Install the (bTer where the temperature

is above 50°F for satisfilctory operation of
the d_Ter control system.

kWARN I N G RIsKOF

* To reduce the risk of severe i_i m T or death, fbllow all installation instruc-

tions.

* Clothes d_Ter insmlla6on must be performed by a qualified installer.
* Install the clothes d_Ter according to these instructions and in accordance

with local codes.

* This d_Ter must be exhausted to the outdoors.
* Use only 4" rigid metal duc6ng for exbaus6ng the clothes d_Ter to the

outdoors.

* DO NOT install a clothes d,Ter with flexible plastic ducdng materials. If

flexible metal (semi-rigid or fbil-type) duct is installed, it must be UL listed
and installed in accordance with the instructions found in "Connecting The
D,Ter To House Vent" on page 5 of this manual. Flexible venting materials
are known to collapse, be easily crushed, and trap lint. These conditions will
obstruct dryer airflow and increase the risk of fire.

* Do not install or store this appliance in any location where it coukt be

exposed to water and or weather.

* Save these instructions. (Installers: Be sure to leave these instructions with

the customer).

NOTE: installation and service of this dryer requires basic
mechanical and electrical skills, it is your responsibility to

contact a qualified installer to make the electrical connections.

TOOLS YOU

WiLL NEED

SLIPJOINTPLIERS

FLATBLADESCREWDRIVER

PHILLIPSSCREWDRIVER

%

Step 1

Step 2

Step 3
Step 4
Step 5
Step 6
Step 7

Prepare the Area and Exhaust for Installation of
New Dryer (see section 1).

Check and Ensure the Existing External Exhaust is
Clean (see sec6on 1) and Meets Attached Installa6on
Specifications (see sec6on 3).

Remove the Foam Shipping Pads (see sec6on 1).
Move the DtTer to the Desired Location.

Connect the Power Supply (see secdon 2).

Connect the External Exhaust (see secdon 4).
Level Your D_Ter (see sec6on 5).

MATERIALS YOU

)

4" DIA.METALDUCT

(RECOMMENDED)

4"DIA,FLEXIBLEMETALSEMI-RIGID)

ULLSTEDTRANSTONDUCT

KITWXO8X10077(INCLUDES2ELBOWS)

4"DIA.FLEXIBLEMETALFOILTYPE)

(IFNEEDED)

ULLSTEDTRANSTONDUCT

(IFNEEDED.)

4"DUCT

CLAMPS(2)

OR

4"SPRING

CLAMPS(2)

WiLL NEED

%

4"DIA.METAL

ELBOW

DUCTTAPE

Step 8

Step 9

For Alcove or Closet Installation, see section 6.
For Bathroom or Bedroom Installation, see section 7.

For Mobile or Manufi_cmred Home see, section S.
For side or bottom exhaust, see section 9.

EXHAUST SAFETY

HOOD GLASSES

3/4"STRAIN

GLOVES RELIEF

ULRECOGNIZED

Check the Operation of the Power Supply

an d Ve n tin g.

Place the Owners Manual and the Installation
Instructions in a Locadon Where They Will Be

Noticed By the Owner.

DRYERPOWER

CORDKIT

(NOTPROVIDED

WITHDRYER)

ULRATED
120/240V,30A

WITH3OR4PRONGS.
IDENTIFYTHEPLUG
TYPEASPERTHE
HOUSERECEPTACLE
BEFOREPURCHASING
LINECORD.

Installation instructions

Minimum Clearance Other Than Alcove or Closet Installation

Minimum clearance m combustible surfhces and for air opening are: 0 in. clearance bod_ sides and 1 in. rear. Consideration
must be given m provide adequate clearance ff)r installation and service.

I-f] PREPARING FOR iNSTALLATiON

OF NEW DRYER

TIP: Install your dryer before installing your washer,
This will allow better access when installing dryer exhaust.

REMOVING LiNT FROM WALL

EXHAUST OPENING

* Remove and discard existing plastic or metal foil

transition duct and replace with UL listed transition
duct°

WALL

/

INTERNALDUCT

OPENING DAMPEROPENS

CHECKTHATEXHAUST

ANDCLOSESFREELY.

TILTTHEDRYERSIDEWAYS
ANDREMOVETHEFOAM
SHIPPINGPADSBY
PULLINGATTHESIDES
ANDBREAKINGTHEM
AWAYFROMTHEDRYER
LEGS.BESURETO
REMOVEALLOFTHE
FOAMPIECESAROUND
THELEGS.

[_ ELECTRICAL CONNECTION

iNFORMATiON

A

WARNING- TO REDUCE THE RISK OF

FIRE, ELECTRICAL SHOCKAND PERSONAL
INJURY:

e DO NOT USE AN EXTENSION CORD OR AN

ADAt_ER PLUG WITH THIS APPLIANCE.

Dwer must be electrically grounded in accordance with
local codes and ordinances, or in the absence of local

codes, in accordance with the NATIONAL ELECTRI-
CAL CODE, ANSI/NFPA NO. 70.

ELECTRICAL REQUIREMENTS

This dryer must be connected to an individual branch circuit,
protected by the required time-delay fllses or circuit breakers. A
Ibm or three-wire, single phase, 120/240V or 120/208V, 60Hz,

30 amp circuit is required.

If the electric supply does not meet the aboxe specifications, then

call a licensed electrician.

GROUNDING INSTRUCTIONS

This dryer must be connected to a grounded metal, permanent
wiring system, or an equipmen/-grounding conductor must be run
with the circuit conductors and connected to the equipment-
grounding terminal on the appliance.

CONNECTING DRYER USING 4-WIRE
CONNECTION (MUST BE USED FOR

MOBILE HOME INSTALLATION)

NOTES: Since January 1,1996, the National Electric code requires
that the new constructions utilize a 4-wire connection to

an electric dryer

t_WARNING:only a 4-conductor cord shah be used when the

appliance is installed in a location where grounding through the
neutral conductor is prohibited. Grounding through the neutral is
prohibited for the new branch-circuit installations, mobile homes,
recreational vehicles, and areas where local codes prohibit
grounding through the neutral conduction.

REMOVEGROUNDSTRAP -
ANDDISCARD,KEEPGREEN

GROUNDSCREW WIRE RELOCATEGREEN

HOT-"'_

GROUNDSCREW
HERE

GREENOR

2

Installation

Instructions

i. Turn off the circuit breaker (s) (30 amp) or remox e tlle ch):er's

circuit fuse at the electrical box.

2. Be sure the ch):er cord is unplugged from tile wall receptacle.

3. Remox e tile power cord coxer located at the lower back.

4. Remox e and discard ground strap. Keep tlle green
ground screw for step 7.

5. Install 3/4 in. LL recognized strain relief to power

cord entl_ hole. Bring power cord through strain relief.

6. Comlect power cord as follows:

7. Attach ground wire of power cord with tile green ground

8. Properly secure power cord to strain relief.

9. Reinstall tile co_ er.

A. Comlect the 2 hot lines to tile outer screws of

tlle terminal block (marked L1 and L2).

B. Com_ect tlle neutral (white) line to tile center of

tile terminal block (marked N).

screw (hole aboxe strain relief bracket). Tighten all

terminal block screws (3) completely.

_ILWARNING: NEVER LEAVE THE

COVER OFF OF THE TERMINAL BLOCK,

CONNECTING DRYER USING 3-WIRE
CONNECTION

IFREQUIRED,BYLOCALCODE,
INSTALLEXTERNALGROUND

(NOTPROVIDED)TOGROUNDED

METAL,COLDWATERPIPE,OR

OTHERESTABLISHEDGROUND

DETERMINEDBYAQUALIFIED

ELECTRICIAN.

_ 3/4",UL

GREEN GROUND
GROUND STRAP

SCREW HOT

WIRE

STRAINRELIEF
BRACKET

RECOGNIZED

RELIEF

EXHAUST INFORMATION

_WARNING - IN CANADA AND IN THE UNITED

STATES, THE REQUIRED EXHAUST DUCT DIAMETER

IS 4 IN (102ram). DO NOT USE DUCT LONGER
THAN SPECIFIED IN THE EXHAUST LENGTH TABLE.

Lsing exhaust longer than specified length wilh

" Increase the drying times and tile energy cost.
, Reduce the ch)_er life.

The correct exhaust installation is YOUR RESPONSIBILITY.
Problems due to incorrect installation are not covered

by the warranty.

Remove and discard existing plastic or metal foil transition
duct and replace with LL listed transition duct.

Tlle MAXIML M ALLOWABLE duct length and number of
bends of the exhaust system depends upon the type of duct,
number of turns, the type of exhaust hood (wall cap), and all
conditions noted below. The maximum duct length for rigid

metal duct is shown in the table below.

, Accumulate lint, creating a potential fire hazard.

EXHAUST LENGTH

RECOMMENDED MAXIMUM LENGTH

Exhaust Hood Types

Recommended Use only for short

No. of 90 -0 Rigid Rigid

Elbows Metal Metal

0 90 Feet 60 Feet

1 60 Feet 45 Feet
2 45 Feet 35 Feet
3 35 Feet 25 Feet
4 25 Feet 15 Feet

run installations

4" DIA.

_ 2-1/2"

NEUTRAL
(White) WIRE

3#10AWGMINIMUMCOPPER

COVER CONDUCTORSOR120/240V30APOWER

SUPPLYCORDKITMARKEDFORUSE
WITHDRYERS& PROVIDEDWITHCLOSED

LOOPORSPADETERMINALSWITH
UPTURNEDENDS(NOTSUPPLIED).

i. Tm'n off tile circuit breaker(s) (30 amp) or remo_ e tile ch_er's

circuit fuse at the electrical box.

2. Be sure the ch_er cord is unplugged Kom the wall.

3. Remoxe the power cord coxer located at tile lower back.

4. Install 3/4 in. LL recognized strain relief to power cord
entl?_ bole. Bring power cord through strain relief.

5. Connect power cord as follows:

A. Com_ect the 2 hot lines to the outer screws of tile

terminal block (marked L1 and L2).

B. Com_ect the neutral {white) line to tile center of

the terminal block {marked N).

6. Be sure grotmd strap is com_ected to neutral (center)
terminal of block and to green ground screw on cabinet
rear. Tighten all terminal block screws (3) completely.

7. Properly secure power cord to strain relief.

S. Reinstall tile co_ er.

A

HOT

,AHb_WARNING: NEVER LEAVE THE

COVER OFF OF THE TERMINAL BLOCK.

EXHAUST SYSTEM CHECK LIST

HOOD OR WALL (AP

• Terminate in a manner to prevent back drafts o1 entry of birds or
other wildlife.

• Termination should present minimal resistance to the exhaust air flow
and should require little or no maintenance to prevent clogging.

• Never install a screen in or over the exhaust duct.This could cause lint build up.

• Wall caps must be installed at least 12 in. above ground level or any other
obstruction with the opening pointed down.

SEPARATION OF TURNS
For best performance, separate all turns by at least 4 ft. of straight duct,

including distance between last ttHn and exhaust hood.
TURNS OTHER THAN 90°

* Oile tt_in of 45 ° or less may be ignored.

* TWO45 ° ttH'i1S should be treated as one 90 ° ttH'i1.

, Each ttH'n over 45 ° should be treated as one 90 ° ttwn.

SEALING OF JOINTS

• _Mljoints should be tight to avoid leaks. The male end of each section of
duct must point away flom the dryer.

Do not assemble the d uctwork with fasteners that extend into the d t_ct.

They will serve as a collection point for lint.

Duct joints can be made air and moisture-tight by wrapping the

overlapped joints with d t_ct rope.

Horizontal runs should slope down toward the outdoors _½inch per foot

INSULATION
Duct work that runs through an unheated area or is near air conditioning

should be insulated to reduce condensation and lint build-up.

3

Installation

[-4-]EXHAUST CONNECTION

_ WARNING - TO REDUCE THE RISK

OF FIRE OR PERSONAL INJURY:

* This clothes dIyer must be exhausted to the outdoors.
* Use only 4" rigid metal ducting for the home exhaust

duct.

. Use only 4" rigid metal or UI,-listed flexible metal

(semi-rigid or foil-type) duct to connect the d_Ter to the

home exhaust duct. It must be installed in accordance

with the instructions found in "Connecting The Dryer
To House Vent" on page 5 of this manual.

* Do not terminate exhaust in a chimney, a wall, a

ceiling, gas vent, crawl space, attic, under an enclosed

floor, or in any other concealed space of a building°
The accumulated lint could create a fire hazard.

* Never terminate the exhaust into a common duct with

a kitchen exhaust system. A combination of grease and
lint creates a potential fire hazard.

* Do not use duct longer than specified in the exhaust

length table. Longer ducts can accumulate lint,

creating a potential fire hazard.

* Never install a screen in or over the exhaust duct. This

will cause lint to accumulate, creating a potential fire

hazard.

* Do not assemble ducta, vork with any fasteners that

extend into the duct. These fasteners can accumulate

lint, creating a potential fire hazard.

* Do not obstruct incoming or exhausted air.
* Provide an access for inspection and cleaning of the

exhaust system, especially at turns and joints. Exhaust

system shall be inspected and cleaned at least once a year.

THiS DRYER COMES READY FOR REAR

EXHAUSTING. iF SPACE iS LiMiTED, USE

THE iNSTRUCTiONS iN SECTION 9 TO

EXHAUST DIRECTLY FROM THE SIDES OR
BOTTOM OF THE CABINET.

STANDARD REAR EXHAUST

{Vented at floor level)

instructions

STANDARD REAR EXHAUST

{Vented above floor level)

ELBOWHIGHLY

_ RECOMMENDED

RECOMMENDED
CONFIGURATION

TOMINIMIZE

EXHAUST
BLOCKAGE.

ELBOWHIGHLY
RECOMMENDED--

=

NOTE: ELBOWS WiLL PREVENT DUCT

KiNKiNG AND COLLAPSING.

[_ LEVELING AND STABiLiZiNG

YOUR DRYER

STANDTHEDRYERUPRIGHTNEARTHEFINALLOCATIONANDADJUST
THE4LEVELINGLEGS,ATTHECORNERS,TOENSURETHATTHEDRYER

ISLEVELFROMSIDETOSIDEANDFRONTTOREAR.

LEVEL
FRONT-TO-BACK.

LEVEL
SIDE-TO-SIDE.

FORSTRAIGHTLINEINSTALLATION,
CONNECTTHEDRYEREXHAUSTTO

THEEXTERNALEXHAUSTHOOD
USINGDUCTTAPEORCLAMP.

EXTERNAL
DUCT

OPENING

DUCTTAPEOR
DUCTCLAMP

4"METALDUCT
(CUTTOPROPER

LENGTH)

NOTE:WESTRONGLYRECOMMENDSOLIDMETALEXHAUSTDUCTING.
HOWEVER,IFFLEXIBLEDUCTINGISUSEDITMUSTBEUL-LISTEDMETAL

NOTPLASTIC.

DUCTTAPEOR
DUCTCLAMP

4LEVELING
LEGS

4

Installation instructions, indoor Exhausting

CONNECTING THE DRYER

TO HOUSE VENT

RIGID METAL TRANSITION DUCT
* For best dxying perfk_rmance, a rigid metal transition

duct is recommended.

* Rigid metal transitions ducts reduce the risk of crush-

ing and kinking.

UL-LISTED FLEXIBLE METAL (SEMI-RIGID) TRANSITION DUCT
* If rigid metal duct cannot be used, then Ul,-listed

flexible metal (semi-rigid) ducting can be used (Kit
WX08X10077).

* Never install flexible metal duct in walls, ceilings, floors

or other enclosed spaces.

* Total length of flexible metal duct should not exceed 8

feet (2.4m).

* For many applications, installing elbows at both the

diyer and the wall is highly recommended (see illustra-
tions below). Elbows allow the d_yer to sit close to the

wall without kinking and or crushing the transition
duct, maximizing d,ying perf_rmance.

* Avoid resting the duct on sharp objects.

UL-LISTEDFLEXIBLEMETAL(FOIL-TYPE)TRANSITION DUCT
* In special installations, it may be necessai T to connect

the d_Ter to the hot_se vent using a flexible metal (fkfil-
type) dt_ct. A UL-listed flexible metal (fkfil-type)dt_ct

may be t]sed ONIX in installations where rigid metal or
flexible metal (semi-rigid) ducfing cannot be used AND

where a 4" diameter can be maintained throughout the
entire length of the transition dt_ct.

* In Canada and the United States, only the flexible

metal (f_il-type) ducts that comply with the "Outline f_r
Clothes D_yer Transition Duct Subject 2158A" shall be

used.

*Never install flexible metal duct in walls, ceilings, floors

or other enclosed spaces.

*Total length of flexible metal duct should not exceed 8

feet (2.4m).

*Avoid resting the duct on sharp objects.
*For best drying perf_rmance:

]. Slide one end of the duct over the clothes dryer

outlet pipe.

2. Secure the duct with a clamp.

3. With the d_yer in its permanent position, extend the
duct to its fifll length. Allow 9" of duct to overlap the
exhaust pipe. Cut offand remove excess duct. Kee I)
the duct as straight as possible t_r maximum airflow.

4. Secure the duct to the exhaust pipe with the other
clamp.

ELBOWHIGHLY
RECOMMENDED

__ SHIGHLY I

MENDED

ALCOVE OR CLOSET iNSTALLATiON

* If yore" dlTer is approved for installation in an alcove or

closet, it will be stated on a label on the dryer back.

° The dryer MUST be vented to the outdoors. See the

EXHAUST INFORMATION sections 3 & 4.

* Minimmn clearance between duer cabinet and adjacent

walls or other surfaces is:

0 in. either side

3 in. Kont and rear

* Minimmn vertical space from floor to overhead cabinets,

ceiling, etc. is 52 in.

* Closet doors must be iouvered or othetwvise ventilated and

must contain a minimum of 60 sq. in. of open area equally
distributed. If the closet contains both a washer and a

duet, doors must contain a minimum of 120 sq. in. of open
area equally distributed.

BATHROOM OR BEDROOM

INSTALLATION

* The dryerMU ST be vented to the outdoors. See

EXHAUST INFORN_TION section 3 & 4.

* The installation must conform with local codes or, in the

absence of local codes, with the NATIONAL ELECTRI-
CAL CODE, ANSI/NFPA NO. 70.

FSqMOBILE OR MANUFACTURED

HOME INSTALLATION

° Installation must conform to the MANUFACTURED

HOME CONSTRUCTION & SAFETY STANDARD,

TITLE 24, PART 32-80 or, when such standard is not

applicable, with %MERICAN NATIONAL STANDARD

FOR MOBILE HOME, ANSI/NFPA NO. 501B.

° The dryer MU ST be vented to the outdoors with the

termination securely fastened to the mobile home

structure. (See EXHAUST INFORMATION
section 3 & 4.)

* The vent MUST NOT be terminated beneath a mobile or

mam_factured home.

* The vent duct material MU ST BE METAL.
* Do not use sheet metal screws or other fastening devices

which extend into the interior of the exhaust vent.

* See section 2 for electrical connection information.

5

Installation Instructions

I-9-]DRYER EXHAUST TO RIGHT, LEFT

OR BOTTOM CABINET

A

WARNING- BEFORE PERFORMING

THIS EXHAUST INSTALLATION, BE SURE
TO DISCONNECT THE DRYER FROM ITS

ELECTRICAL SUPPLY. PROTECT YOUR
HANDS AND ARMS FROM SHARP EDGES
WHEN WORKING INSIDE THE CABINET.
BE SURE TO WEAR GLOVES

REMOVE
SCREW
ANDSAVE.

REMOVE
DESIRED
KNOCKOUT

(ONEONLY).

Detach and remove the bottom, right or left side knockout
as desired. Remove the screw inside the dryer exhaust duct

and save. Pull the duct out of the dryer.

FIXINGHOLE

\

ADDING NEW DUCT

FIXING
HOLE

PORTION"A"

RIGHTOR
LEFTSIDE
EXHAUST

Reconnect the cut portion (A) of the duct to the blower
housing. Make sure that the shortened duct is aligned with
the tab in the base. Use the screw saved previously to secure
the duct in place through the tab on the appliance base.

ADDING ELBOW AND DUCT FOR

EXHAUST TO LEFT OR RIGHT

SIDE OF CABINET

Preassemble 4" elbow with 4" duct. Wrap duct tape

around joint.

Insert duct assembly, elbow first, through the side opening

and connect the elbow to the dryer internal duct.

CAUTION: Be sure not to pull or damage the

electrical wires inside the dryer
when inserting the duct.

B A

9"

Cut the duct as shown and keep portion A.

TAB LOCATION

BENDTAB
UP45o

Through the rear opening, locate the tab in the middle of
the appliance base. Lift the tab to about 45° using a fiat

blade screwdriver.

J_

BEADDEDTO
LEFTORRIGHTSIDE

EXHAUSTCAN

. TAPE

...... J-

Apply duct tape as shown on the joint between the dryer

internal duct and the elbow.

DUCT

CAUTION:

Internal duct joints must be

__ secured with tape, otherwisethey may separate and cause

6

a safety hazard.

DUCT

Installation

Instructions

ADDING ELBOW FOR EXHAUST
THROUGH BOTTOM OF CABINET

* Insert tile elbow through the rear opening and connect it

to the dryer internal duct.

* Apply duct tape oil thejoim between tile dryer internal

duct and elbow, as shown oil page 6.

CAUTION:

Internal duct joints must be secured with tape,
otherwise they may separate and cause a
safety hazard.

ADDING COVER PLATE TO REAR
OF CABINET (SIDES AND BOTTOM
EXHAUST)

CHANGING DIRECTION OF

DOOR OPENING

1. Open the door and remove the filler plugs opposite the

hinges. With the door completely open, remove the
bottom screws from each hinge on the dryer face. Insert
these screws about half way into the TOP holes, for each
hinge on the opposite side (where you removed the filler
plugs). Apply firm pressure to get the screw started.

2. Loosen the top screws from each hinge on the dryer face
half way. With one hand hoMing the top of the door and
the other hand holding the bottom, remove the door
from the dD'er by lifting itUP and OUT.

3. Rotate the door 180 °. Insert the door on the opposite side
of the opening by moving the doorlN and DOWN
mltil the top hinge and the bottom hinge are resting on
the top screws inserted in step 1.

4. Remove the remaining screws from the side of the
opening from which the door was removed. With these
screws secure each hinge at the bottom. Tighten the two
top screws on each hinge. Reinsert the plastic plugs on

the side from which the door was removed.

REMOVETHE
BOTTOMSCREW
FROMEACHHINGE
ONTHEDRYER

LOOSENTHETOP
SCREWSFROM
EACHHINGEON
THEDRYERFACE
HALFWAY.

÷

PLATE
(KITWE1M454)

Connect standard metal elbows and ducts to complete the
exhaust system. Cover back opening with a plate (Fdt
WEIM454) available from your local service provider.
Place dryer in final location.

_ WARNING-NEVER LEAVETHE BACK ]

OPENING WITHOUT THE PLATE. (KitWglM454)

TO REGISTER YOUR DRYER

CALL TOLL-FREE

1-888-269-1192

Prompt registration confirms your right to protection under the

terms of your warranty.

www.GEAppliances.com (US)

For Questions on Installation, Call: 1-800-GECARES (US)

5(t(t,\4 _tiPO05 Re'J) Pub # 31 16224 7

_.__FAC_

MOVETHEDOORINAND
DOWNUNTILTHETOPHINGE
ANDTHEBOTTOMHINGEARE

RESTINGONTHETOPSCREWS

INSERTEDINSTEP1.

SECUREEACHHINGE

ATTHEBOTTOMAND

TIGHTENTHETWOTOP
SCREWSOFEACHHINGE.

SERVICING

WARNING- LABEL ALL WIRES

PRIOR TO DISCONNECTING WHEN
SERVICING CONTROLS. WIRING
ERRORS CAN CAUSE IMPROPER AND
DANGEROUS OPERATION AFTER

SERVICING/INST ALIATION.

For servicing t)hone numbers for replacement parts, and

other information, refer to Owner's Manual or visit our

Web sire.

Notes