Page 1
DS4600
DS5000
DX2300
DX4500
Owner’s Manual
Dryers
175D1807P551 49-90283 12-05 JR
Safety Instructions . . . . . . . . . . . . . 2–4
Operating Instructions
Control Features for
Model DS5000 . . . . . . . . . . . . . . . . . . . . . . .11
Control Panel and Settings for
Models DS4600, DX2300
and DX4500 . . . . . . . . . . . . . . . . . . . . . . . . 5–7
Control Panel for Model DS5000 . . . . . . . 8
Cycle Status for Model DS5000 . . . . . . .12
Dryer Features for Models DS4600,
DX2300 and DX4500 . . . . . . . . . . . . . . . . . .7
Dryer Features for Model DS5000 . . . . .13
Drying Cycles for Model DS5000 . . . . . .10
Dryness Levels for Model DS5000 . . . . .10
Easy One Touch Cycles
for Model DS5000 . . . . . . . . . . . . . . . . . . . 8, 9
Heat Settings for Model DS5000 . . . . . .10
Loading and Using the Dryer . . . . . . . . .15
Reversing the Door . . . . . . . . . . . . . . . . . . 14
Timed Dry Cycles for
Model DS5000 . . . . . . . . . . . . . . . . . . . . . . .10
Venting the Dryer . . . . . . . . . . . . . . . . . . . .16
Troubleshooting Tips . . . . . . . . 17–19
Consumer Support
Consumer Support . . . . . . . . . . Back Cover
Product Registration . . . . . . . . . . . . . . 21, 22
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
ge.com
Write the model and serial
numbers here:
Model # ________________
Serial # ________________
You can find them on a label
on the front of the dryer behind
the door.
Page 2
WARNING!
For your safety, the information in this manual must be followed to minimize the risk of fire
or explosion, electric shock, or to prevent property damage, personal injury, or death.
WHAT TO DO IF YOU SMELL GAS:
Do not try to light a match, or cigarette, or
turn on any gas or electrical appliance.
Do not touch any electrical switch;
do not use any phone in your building.
Clear the room, building or area of all
occupants.
Immediately call your gas supplier from
a neighbor’s phone. Follow the gas
supplier’s instructions carefully.
If you cannot reach your gas supplier,
call the fire department.
5
4
3
2
1
California Safe Drinking Water and Toxic Enforcement Act
This act requires the governor of California to publish a list of substances known to the state to cause
cancer, birth defects or other reproductive harm and requires businesses to warn customers of potential
exposure to such substances.
Gas appliances can cause minor exposure to four of these substances, namely benzene, carbon monoxide,
formaldehyde and soot, caused primarily by the incomplete combustion of natural gas or LP fuels.
Properly adjusted dryers will minimize incomplete combustion. Exposure to these substances can be
minimized further by properly venting the dryer to the outdoors.
■ Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
■ Installation and service must be
performed by a qualified installer,
service agency or the gas supplier.
2
Operating Instructions Safety InstructionsConsumer Support Troubleshooting Tips
■ Properly ground dryer to conform with all
governing codes and ordinances. Follow details
in Installation Instructions.
■ Install or store where it will not be exposed to
temperatures below freezing or exposed to
the weather.
■ Connect to a properly rated, protected and sized
power supply circuit to avoid electrical overload.
■ Remove the colored protective film from the
control panel.
■ Remove all sharp packing items and dispose of
all shipping materials properly.
Exhaust/Ducting:
Gas dryers MUST be exhausted to the outside.
Use only rigid metal 4″ diameter ductwork
inside the dryer cabinet. Use only rigid metal
or flexible metal 4″ diameter ductwork for
exhausting to the outside. USE OF PLASTIC OR
OTHER COMBUSTIBLE DUCTWORK CAN CAUSE A
FIRE. PUNCTURED DUCTWORK CAN CAUSE A FIRE
IF IT COLLAPSES OR BECOMES OTHERWISE
RESTRICTED IN USE OR DURING INSTALLATION.
For complete details, follow the Installation
Instructions.
2
1
PROPER INSTALLATION
This dryer must be properly installed and located in accordance with the Installation Instructions
before it is used. If you did not receive an Installation Instructions sheet, you can receive one by
visiting ge.com, or by calling 800.GE.CARES (800.432.2737).
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
Page 3
3
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions
ge.com
WARNING!
YOUR LAUNDRY AREA
■ Keep the area underneath and around
your appliances free of combustible materials
(lint, paper, rags, etc.), gasoline, chemicals and
other flammable vapors and liquids.
■ Keep the floor around your appliances clean
and dry to reduce the possibility of slipping.
■ Close supervision is necessary if this appliance is
used by or near children. Do not allow children
to play on, with or inside this or any other
appliance.
■ Keep all laundry aids (such as detergents,
bleaches, etc.) out of the reach of children,
preferably in a locked cabinet. Observe all
warnings on container labels to avoid injury.
■ Never climb on or stand on the dryer top.
WHEN USING YOUR DRYER
■ Never reach into the dryer while the drum is
moving. Before loading, unloading or adding
clothes, wait until the drum has completely
stopped.
■ Clean the lint filter before each load to prevent
lint accumulation inside the dryer or in the
room. DO NOT OPERATE THE DRYER WITHOUT
THE LINT FILTER IN PLACE.
■ Do not wash or dry articles that have been
cleaned in, washed in, soaked in or spotted
with combustible or explosive substances (such as
wax, oil, paint, gasoline, degreasers, dry-cleaning
solvents, kerosene, etc.) which may ignite or
explode. Do not add these substances to the
wash water. Do not use or place these substances
around your washer or dryer during operation.
■ Do not place items exposed to cooking oils in
your dryer. Items contaminated with cooking oils
may contribute to a chemical reaction that could
cause a clothes load to catch fire.
■ Any article on which you have used a cleaning
solvent or that contains flammable materials
(such as cleaning cloths, mops, towels used in
beauty salons, restaurants or barber shops, etc.)
must not be placed in or near the dryer until
solvents or flammable materials have been
removed. There are many highly flammable
items used in homes such as acetone, denatured
alcohol, gasoline, kerosene, some household
cleaners, some spot removers, turpentines,
waxes, wax removers and products containing
petroleum distillates.
■ The laundry process can reduce the flame
retardancy of fabrics. To avoid such a result,
carefully follow the garment manufacturer’s
care instructions.
■ Do not dry articles containing rubber, plastic
or similar materials such as padded bras, tennis
shoes, galoshes, bath mats, rugs, bibs, baby pants,
plastic bags, pillows, etc. that may melt or burn.
Some rubber materials, when heated, can under
certain circumstances produce fire by
spontaneous combustion.
■ Do not store plastic, paper or clothing that
may burn or melt on top of the dryer during
operation.
■ Garments labeled Dry Away from Heat or Do Not
Tumble Dry (such as life jackets containing Kapok)
must not be put in your dryer.
■ Do not dry fiberglass articles in your dryer.
Skin irritation could result from the remaining
particles that may be picked up by clothing
during subsequent dryer uses.
■ To minimize the possibility of electric shock,
unplug this appliance from the power supply
or disconnect the dryer at the household
distribution panel by removing the fuse or
switching off the circuit breaker before
attempting any maintenance or cleaning
(except the removal and cleaning of the lint
filter). NOTE: Turning the Cycle Selector knob
to an off position or pressing PAUSE does NOT
disconnect the appliance from the power supply.
Page 4
WHEN NOT USING YOUR DRYER
■ Grasp the plug firmly when disconnecting this
appliance to avoid damage to the cord while
pulling. Place the cord away from traffic areas
so it will not be stepped on, tripped over or
subjected to damage.
■ Do not attempt to repair or replace any part of
this appliance or attempt any servicing unless
specifically recommended in this Owner’s Manual
or in published user-repair instructions that you
understand and have the skills to carry out.
■ Before discarding a dryer, or removing it from
service, remove the dryer door to prevent
children from hiding inside.
■ Do not tamper with controls.
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
SAVE THESE INSTRUCTIONS
4
WARNING!
WHEN USING YOUR DRYER (cont.)
■ Never attempt to operate this appliance if it is
damaged, malfunctioning, partially disassembled,
or has missing or broken parts, including a
damaged cord or plug.
■ The interior of the machine and the exhaust
duct connection inside the dryer should be
cleaned at least once a year by a qualified
technician. See the Loading and Using the Dryer
section.
■ If yours is a gas dryer, it is equipped with an
automatic electric ignition and does not have
a pilot light. DO NOT ATTEMPT TO LIGHT WITH
A MATCH. Burns may result from having your
hand in the vicinity of the burner when the
automatic ignition turns on.
■ You may wish to soften your laundered fabrics
or reduce the static electricity in them, by using
a dryer-applied fabric softener or an anti-static
conditioner. We recommend you use either a
fabric softener in the wash cycle, according to
the manufacturer’s instructions for those
products, or try a dryer-added product for
which the manufacturer gives written assurance
on the package that their product can be safely
used in your dryer. Service or performance
problems caused by use of these products are
the responsibility of the manufacturers of those
products and are not covered under the warranty
to this appliance.
Operating Instructions Safety InstructionsConsumer Support Troubleshooting Tips
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
Page 5
5
NOTE: Drying times will vary according to the type of heat used (Electric, Natural or LP gas), size of load,
types of fabrics, wetness of clothes and condition of exhaust ducts.
You can locate your model number on the label on the front of the dryer behind the door.
Throughout this manual, features and
appearance may vary from your model.
Model DS4600
Model DX2300
3
Model DX4500
About the dryer control panel—for models DS4600,
DX2300 and DX4500.
ge.com
2
3 21
23 1
Page 6
IMPORTANT: Clean the lint filter each time you use the dryer.
Fabric Care/Temperature (on some models)
COTTONS For regular to heavy cottons.
REG. HEAT
EASY CARE For synthetics, blends, delicates and items labeled permanent press.
MED. HEAT
DELICATES On some models. For delicates, synthetics and items labeled tumble dry low.
LOW HEAT
FLUFF For fluffing items without heat. Use the TIMED DRY cycle.
NO HEAT
Automatic cycles automatically determine fabric dryness. Select LESS DRY if you want your clothes
slightly damp at the end of the drying cycle. Select MORE DRY if you want them to feel drier. Timed
cycles run for a selected time.
Drying Cycles
COTTONS For cottons and most linens. For most loads select OPTIMUM DRY (on some models) or select the
Preferred Regular Setting marked with an *.
EASY CARE For wrinkle-free, permanent press and delicate items, and knits.
TIMED DRY Set the Cycle Selector at the desired drying time.
DAMP DRY For leaving items partially damp.
DEWRINKLE For removing wrinkles from items that are clean and dry or that are very lightly damp.
QUICK FLUFF For freshening or fluffing up already dry clothing, fabrics, linens and pillows. Use with FLUFF NO HEAT.
Provides 10 minutes of no heat tumbling.
Start—Close the dryer door. Select START. Opening the door during operation will stop the dryer.
To restart the dryer, close the door and select START to complete the cycle.
1
2
3
About the control settings—for models DS4600, DX2300 and DX4500.
Operating Instructions Safety InstructionsConsumer Support Troubleshooting Tips
6
Page 7
Automatic Cycle Signal (on some models)
At the end of each cycle, there is
approximately 15 minutes of no-heat
tumbling after the laundry is dry.
A reminder signal will sound periodically
during this time to remind you to remove
the laundry.
7
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions
Cycle Signal Option (on some models)
This signal will sound just before the end
of the cycle to remind you to remove the
clothes. On some models the signal sound
level cannot be adjusted.
If you selected the WRINKLE CARE option,
the signal will sound at the end of the
drying time and will sound several times
during the WRINKLE CARE cycle. This will
remind you that it is time to remove the
clothes.
NOTE:
■ Remove garments promptly at the sound
of the signal. Place clothes on hangers so
wrinkles won’t set in.
■ Use the Cycle Signal especially when
drying fabrics like polyester knits and
permanent press. These fabrics should
be removed so wrinkles won’t set in.
ge.com
About dryer features
—for models DS4600, DX2300 and DX4500.
Stainless Steel Drum (on some models)
The stainless steel used to make the
dryer drum provides the highest reliability
available in a GE dryer. If the dryer drum
should be scratched or dented during
normal use, the drum will not rust or
corrode. These surface blemishes will
not affect the function or durability of
the drum.
Drum Lamp (on some models)
Before replacing the light bulb, be sure to
unplug the dryer power cord or disconnect
the dryer at the household distribution
panel by removing the fuse or switching
off the circuit breaker. Reach above dryer
opening from inside the drum. Remove the
bulb and replace with the same size bulb.
Drying Rack (on some models)
A handy drying rack may be used for drying
delicate items such as washable sweaters.
Hook the rack over the lint filter so the rack
extends into the dryer drum.
NOTE:
■ The drying rack must be used with the
TIMED CYCLE.
■ Do not use this drying rack when there
are other clothes in the dryer.
Page 8
8
Model DS5000
ONE T
OUCH
Quick Start Guide
• Clean lint filter
• Add clothes
• Select dry cycle
• Check dryness level
• Check heat setting
• Close door
• Push START
Your new dryer offers the convenience of starting your dryer loads with our easy ONE TOUCH cycles. Make one simple selection, and your
DRYNESS LEVEL and HEAT SETTING are automatically set. Then all you have to do is press START.
Easy ONE TOUCH cycles—for model DS5000.
You can locate your model number on the label on the front of the dryer, behind the door.
NOTE: Any time you make a selection that is incompatible with the chosen dry cycle, the dryer will beep twice.
Dryer control panel—for model DS5000.
Page 9
PRESS... AUTOMATICALLY SELECTS... THEN PRESS...
For cottons and most linens.
O
NE TOUCH cycles use the Sensor Dry Plus feature, which continuously monitors the amount of moisture in the load and stops the dryer
when the clothes are dry. Throughout this manual, features and appearance may vary from your model.
ONE TOUCH selections. ge.com
For loads consisting of
cottons and poly-blends.
For wrinkle-free and
permanent press items.
For knits and sweaters with fabric care
labels that say “Machine Dry”.
For lingerie and special-care fabrics.
You can change any of the automatic settings by simply pressing the desired pads.
Changing the automatic settings.
9
Page 10
DEWRINKLE
Use this feature to remove wrinkles from items that are dry or slightly damp.
Automatic DEWRINKLE settings:
AIR DRY
Use this feature to tumble items without heat.
Automatic AIR DRY settings:
Throughout this manual, features and appearance may vary from your model.
About drying cycles.
Operating Instructions Safety InstructionsConsumer Support Troubleshooting Tips
10
MORE DRY
Use for heavy-duty fabrics.
DRY
Use for a normal dryness level suitable for most loads. This is the preferred cycle
for energy saving.
LESS DRY
Use for lighter fabrics.
DAMP
For leaving items partially damp.
About dryness levels.
HIGH
For regular to heavy cottons.
MEDIUM
For synthetics, blends and items labeled permanent press.
LOW
For delicates, synthetics and items labeled Tumble Dry Low.
EXTRA LOW
For lingerie and special-care fabrics.
About heat settings.
To use TIMED DRY:
1. Select the drying time.
2. Select the HEAT SETTING.
3. Select any OPTIONS.
4. Close door.
5. Push START.
About timed dry cycles.
Page 11
11
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions
START/PAUSE
■ Press twice to select the last cycle you used and start the dryer.
■ If you have selected a new cycle, press once to start the cycle.
■ If the dryer is running, press once to interrupt the cycle; press again to continue the cycle.
Throughout this manual, features and appearance may vary from your model.
About control features. ge.com
STOP
■ This pad should not be used to interrupt or pause a cycle.
■ Pressing this pad will cancel the current settings.
Estimated Time Remaining
Each time the dryer is used, it “learns” what types of loads you dry most often.
It takes this data and determines the approximate time it will take the load to dry.
As the cycle begins, you will see the approximate total cycle time in the display. Then lights
will flash in the display, and the SENSING light will flash. This means the dryer is continuously
monitoring the amount of moisture in the load. The lights will continue until the dryer senses
a low level of moisture in the load. At that point, the dryer will calculate and display the
approximate time remaining.
(Appearance and
features may vary)
SIGNAL
Alerts you that the cycle is complete. The beeper will continue to sound every two minutes for
the next 6 minutes, until the clothes are removed. The clothes should be removed when the
beeper goes off so wrinkles won’t set in.
On some models, press SIGNAL to turn the beeper on or off.
On some models, press SIGNAL to select low or high volume, or to turn the beeper off.
EXTEND TUMBLE
Minimizes wrinkles by adding approximately 20 minutes of no-heat tumbling after clothes are
dry. The beeper will sound every 90 seconds to remind you to remove the clothes. The EST.
TIME REMAINING display will show 00.
ADD TIME (on some models)
This option can be used to extend drying time at the end of any cycle. Each time the pad is
pressed, 10 minutes is added.
Page 12
12
These cycle status indicator lights display what part of the cycle the dryer is in and remind you to clean the lint filter.
About cycle status.
SensorDry Plus
This light comes on when a ONE
TOUCH Sensor Dry Cycle is selected.
TIMED DRY
This light comes on when AIR DRY, DEWRINKLE or TIMED DRY is selected.
EXTENDED TUMBLE
This light comes on when the EXTEND TUMBLE option is selected.
CLEAN LINT FILTER
This light is a reminder to clean the lint filter. It comes on at the end of a cycle and goes off
when the door is opened.
SENSING
Sensor Dry Cycles provide greater drying accuracy than standard machines, resulting in shorter
dry times and better clothes care. The SENSING light will flash and lights will flash in the display
while the dryer is monitoring the amount of moisture remaining in the clothes. When the
SENSING light goes out, the dryer will calculate and display the approximate time remaining.
Operating Instructions Safety InstructionsConsumer Support Troubleshooting Tips
Page 13
About dryer features.
ge.com
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions
Stainless Steel Drum (on some models)
The stainless steel used to make the
dryer drum provides the highest reliability
available in a GE dryer. If the dryer drum
should be scratched or dented during
normal use, the drum will not rust or
corrode. These surface blemishes will
not affect the function or durability of
the drum.
Drum Lamp (on some models)
Before replacing the light bulb, be sure to
unplug the dryer power cord or disconnect
the dryer at the household distribution
panel by removing the fuse or switching
off the circuit breaker. Reach above dryer
opening from inside the drum. Remove the
bulb and replace with the same size bulb.
Drying Rack (on some models)
A handy drying rack may be used for drying
delicate items such as washable sweaters.
Hook the rack over the lint filter so the rack
extends into the dryer drum.
NOTE:
■ The drying rack must be used with the
TIMED CYCLE.
■ Do not use this drying rack when there
are other clothes in the dryer.
13
Page 14
Reversing the Door
Tools needed:
■ Standard #2 ■ Tape-tipped
■ Phillips screwdriver ■ putty knife
Open the door and remove the filler plugs opposite the hinges. With the door
completely open, remove the bottom screw from each hinge on the dryer face.
Insert these screws about half way into the TOP holes, for each hinge, on the opposite
side (where you removed the filler plugs). Apply firm pressure to get the screw started
in new holes.
Loosen top screw from each hinge on the dryer face half way. With one hand holding
the top of the door and the other hand holding the bottom, remove the door from
the dryer by lifting it UP and OUT.
Rotate the door 180°. Insert it on the opposite side of the opening by moving the door
IN and DOWN until the top hinge and the bottom hinge are resting on the top screws
inserted in step 1.
Remove the remaining screws from the side of the opening from which the door
was removed. With these screws, secure each hinge at the bottom. Tighten the
two top screws of each hinge. Reinsert the plastic plugs on the side from which
the door was removed.
4
3
2
1
Operating Instructions Safety InstructionsConsumer Support Troubleshooting Tips
About reversing the door.
14
Page 15
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions
Sorting and Loading Hints
As a general rule, if clothes are sorted properly for
the washer, they are sorted properly for the dryer.
Do not add fabric softener sheets once the load has
become warm. They may cause fabric softener stains.
Bounce®Fabric Conditioner Dryer Sheets have been
approved for use in all GE Dryers when used in
accordance with the manufacturer’s instructions.
Do not overload. This wastes energy and causes wrinkling.
Do not dry the following items: fiberglass items, woolens,
rubber-coated items, plastics, items with plastic trim and
foam-filled items.
Fabric Care Labels
The Exterior: Wipe or dust any spills or washing
compounds with a damp cloth. Dryer control
panel and finishes may be damaged by some
laundry pretreatment soil and stain remover
products. Apply these products away from the dryer.
The fabric may then be washed and dried normally.
Damage to your dryer caused by these products is
not covered by your warranty.
The Lint Filter: Clean the lint filter before each
use. Moisten your fingers and reach into the filter
opening. Run your fingers
across the filter. Have a
qualified
technician vacuum the lint from the dryer
once a year.
Stainless Steel: To clean stainless steel surfaces,
use a damp cloth with a mild, non-abrasive
cleaner suitable for stainless steel surfaces.
Remove the cleaner residue, and then dry
with a clean cloth.
The Exhaust Duct: Inspect and clean the exhaust
ducting at least once a year to prevent clogging.
A partially clogged exhaust can lengthen the
drying time.
Follow these steps:
Turn off electrical supply by disconnecting the
plug from the wall socket.
Disconnect the duct from the dryer.
Vacuum the duct with the hose attachment and
reconnect the duct.
The Exhaust Hood: Check from the outside that the
flaps of the hood move freely when operating. Make
sure that there is no wildlife (birds, insects, etc.)
nesting inside the duct or hood.
3
2
1
Care and Cleaning of the Dryer
Machine
wash
cycle
Normal
Permanent Press/
wrinkle resistant
Gentle/
delicate
Hand wash
Do not wash Do not wring
Water
temperature
Hot
(50°C/120°F)
Warm
(40°C/105°F)
Cold/cool
(30°C/85°F)
Tumble
dry
Dry
Normal
Permanent Press/
wrinkle resistant
Gentle/
delicate
Do not tumble dry
Do not dry
(used with
do not wash)
Heat
setting
High
Medium
Low
No heat/air
Special
instructions
Line dry/
hang to dry
Drip dry
Dry flat
In the shade
Bleach
symbols
Any bleach
(when needed)
Only non-chlorine bleach
(when needed)
Do not bleach
Below are fabric care label “symbols” that affect the clothing you will be laundering.
WASH LABELS
DRY LABELS
BLEACH LABELS
15
Loading and using the dryer.
Always follow the fabric manufacturer’s care label when laundering. ge.com
Page 16
For the best drying performance, the dryer needs to be properly vented. The dryer will use more energy
and run longer if it is not vented to the below specifications. Carefully follow the details on Exhausting in the
Installation Instructions.
■ Use only rigid metal 4″ diameter ductwork inside the
dryer cabinet. Use only rigid metal or flexible metal 4″
diameter ductwork for exhausting to the outside.
■ Do not use plastic or other combustible ductwork.
■ Use the shortest length possible.
■ Do not crush or collapse.
■ Avoid resting the duct on sharp objects.
■ Venting must conform to local building codes.
Venting the Dryer
Correct
Venting
Incorrect
Venting
16
Operating Instructions Safety InstructionsConsumer Support Troubleshooting Tips
Loading and using the dryer.
Always follow the fabric manufacturer’s care label when laundering.
Page 17
17
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions
Troubleshooting Tips
Save time and money! Review the charts on the following pages, or
visit ge.com. You may not need to call for service.
Before you call for service…
ge.com
OPERATION Possible Causes What To Do
Control pads not Controls accidentally put in • Press STOP.
responding (on some service mode
models)
Dryer doesn’t start Control panel is “asleep” • This is normal. Press START twice to choose the last cycle
(on some models) you used and to start the dryer.
Dryer is unplugged • Make sure the dryer plug is pushed completely into
the outlet.
Fuse is blown/circuit breaker • Check the building’s fuse/circuit breaker box and
is tripped replace fuse or reset breaker. NOTE: Electric dryers
use two fuses or breakers.
Dryer doesn’t heat Fuse is blown/circuit breaker • Check the building’s fuse/circuit breaker box and
is tripped; the dryer may tumble replace both fuses or reset both breakers. Your dryer
but not heat may tumble if only one fuse is blown or one breaker
tripped.
Gas service is off • Make sure gas shutoff at dryer and main shutoff are
fully open.
LP gas supply tank is empty • Refill or replace tank. Dryer should heat when utility
or there has been a utility service is restored.
interruption of natural gas
(gas models)
Dryer shakes or Some shaking/noise is normal. • Move dryer to an even floor space, or adjust leveling legs
makes noise Dryer may be sitting unevenly as necessary until even.
Inconsistent drying times Type of heat • Drying time will vary according to the type of heat used.
If you recently changed from an electric to a gas
(natural or LP) dryer, or vice versa, the drying time
could be different.
Type of load and • The load size, types of fabric, wetness of clothes and the
drying conditions length and condition of the exhaust system will affect
drying times.
No numbers displayed Dryer is continuously • This is normal. When the dryer senses a low level of
during cycle, only lights monitoring the amount of moisture in the load, the dryer will display the dry time
(on some models) moisture in the clothes remaining.
Est. Time Remaining The estimated time may change • This is normal.
jumped to a lower when a smaller load than usual
number (on some models) is drying
Clothes are still wet The door was opened mid-cycle. • A dry cycle must be reselected each time a new load
and dryer shut off The load was then removed from is put in.
after a short time the dryer and a new load put in
without selecting a new cycle
Small load • When drying only a few items, choose TIMED DRY.
Load was already dry except • Choose TIMED DRY to dry damp collars and waistbands.
for collars and waistbands In the future, when drying a load with collars and
waistbands, choose MORE DRY.
Dryer is not level • Move dryer to an even floor space or adjust leveling legs
as necessary until even.
Page 18
Operating Instructions Safety InstructionsConsumer Support Troubleshooting Tips
18
Before you call for service…
Troubleshooting Tips
OPERATION Possible Causes What To Do
The DRY dryness level Load consists of a mixture • When combining heavy and light fabrics in a load,
was chosen but load is of heavy and light fabrics choose MORE DRY.
still damp (on some models)
Exhaust system is blocked • Inspect and clean exhaust system.
Cannot make a The DRYNESS LEVEL, HEAT • This is normal.
selection and the SETTING or OPTION that
dryer beeps twice you are trying to select is
(on some models) incompatible with the chosen
dry cycle
Dryer is running but The EXTEND TUMBLE • This is normal. During extended tumbling, the time
00 is displayed in option (on some models) remaining is not displayed. The extended tumbling
Est. Time Remaining was chosen option lasts approximately 20 minutes.
(on some models)
LAUNDRY PRACTICES Possible Causes What To Do
Clothes are wrinkled Overdrying • Select a shorter drying time.
• Remove items while they still hold a slight amount of
moisture. Select a LESS DRY or DAMP setting.
Overloading • Separate large loads into smaller ones.
Letting items sit in dryer after •Remove items when cycle ends and fold or hang
cycle ends immediately, or use the EXTEND TUMBLE option
(on some models).
Clothes shrink Some fabrics will naturally shrink • To avoid shrinkage, follow garment care labels exactly.
when washed. Others can be
safely washed, but will shrink
• Some items may be pressed back into shape after drying.
in the dryer
• If you are concerned about shrinkage in a particular
item, do not machine wash or tumble dry it.
Greasy spots on clothes Improper use of fabric softener • Follow directions on fabric softener package.
Drying dirty items • Use your dryer to dry only clean items. Dirty items can
with clean ones stain clean items and the dryer.
Clothes were not • Sometimes stains which cannot be seen when the
completely clean clothes are wet appear after drying. Use proper washing
procedures before drying.
Lint on clothes Lint filter is full • Clean lint screen before each load.
Improper sorting • Sort lint producers (like chenille) from lint collectors
(like corduroy).
Static electricity can attract lint • See suggestions in this section under STATIC.
Overloading • Separate large loads into smaller ones.
Paper, tissue, etc., left in pockets • Empty all pockets before laundering clothes.
Page 19
19
LAUNDRY PRACTICES Possible Causes What To Do
Static occurs No fabric softener was used • Try a fabric softener.
• Bounce®Fabric Conditioner Dryer Sheets have been
approved for use in all GE Dryers when used in
accordance with the manufacturer’s instructions.
Overdrying • Try a fabric softener.
• Adjust setting to LESS DRY or DAMP.
Synthetics, permanent press • Try a fabric softener.
and blends can cause static
Collars and waistbands The dryness monitor senses • Choose TIMED DRY to dry damp collars and waistbands.
still wet at end of cycle that the body of the clothes In the future, when drying a load with collars and
is dry waistbands, choose MORE DRY.
Clothes take too long Improper sorting • Separate heavy items from lightweight items (generally,
to dry a well-sorted washer load is a well-sorted dryer load).
Large loads of heavy fabrics • Large, heavy fabrics contain more moisture and take
(like beach towels) longer to dry. Separate large, heavy fabrics into smaller
loads to speed drying time.
Controls improperly set •Match control settings to the load you are drying.
Lint filter is full • Clean lint filter before every load.
Improper or obstructed ducting • Check installation instructions for proper
ducting/venting.
• Make sure ducting is clean, free of kinks and
unobstructed.
• Check to see if outside wall damper operates easily.
• Check the Installation Instructions to make sure the
dryer venting is correct.
Blown fuses or tripped circuit • Replace fuses or reset circuit breakers. Since most
breaker dryers use 2 fuses/breakers, make sure both are
operating.
Overloading/combining loads •Do not put more than one washer load in the dryer at
a time.
Underloading • If you are drying only one or two items, add a few items
to ensure proper tumbling.
ge.com
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions
Page 20
20
Notes.
Operating Instructions Safety InstructionsConsumer Support Troubleshooting Tips
Page 21
21
General Electric Company
Warranty Registration Department
P.O. Box 32150
Louisville, KY 40232-2150
GE Service Protection Plus
™
GE, a name recognized worldwide for quality and dependability, offers you
Service Protection Plus
™
—comprehensive protection on all your appliances—
No Matter What Brand!
Benefits Include:
• Backed by GE
• All brands covered
• Unlimited service calls
• All parts and labor costs included
• No out-of-pocket expenses
• No hidden deductibles
• One 800 number to call
You will be completely satisfied with our service protection or you may request your money back
on the remaining value of your contract. No questions asked. It’s that simple.
Protect your refrigerator, dishwasher, washer and dryer, range, TV, VCR and much more—any brand!
Plus there’s no extra charge for emergency service and low monthly financing is available. Even icemaker
coverage and food spoilage protection is offered. You can rest easy, knowing that all your valuable
household products are protected against expensive repairs.
Place your confidence in GE and call us in the U.S. toll-free at 800.626.2224
for more information.
*All brands covered, up to 20 years old, in the continental U.S.
We’ll Cover Any Appliance.
Anywhere. Anytime.*
Please place in envelope and mail to:
✁
Cut here
Page 22
22
Consumer Product Ownership Registration
Important
Mail
Today!
First
Name
Mr. ■■ Ms. ■■ Mrs. ■■ Miss ■■
Street
Address
City
State
Date Placed
In Use
Month
Day
Year
Zip
Code
Apt. #
Last
Name
Phone
Number
_
_
Consumer Product Ownership Registration
Dear Customer:
Thank you for purchasing our product and thank you for placing your confidence in us.
We are proud to have you as a customer!
Follow these three steps to protect your new appliance investment:
Important: If you did not get a registration card with your
product, detach and return the form below to
ensure that your product is registered, or register
online at ge.com.
1
23
Model Number Serial Number
✁
Cut here
Complete and mail
your Consumer
Product Ownership
Registration today.
Have the peace of
mind of knowing we
can contact you in
the unlikely event of
a
safety modification.
After mailing the
registration below,
store this document
in a safe place. It
contains information
you will need should
you require service.
Our service number is
800.GE.CARES
(800.432.2737).
Read your Owner’s
Manual carefully.
It will help you
operate your new
appliance properly.
Model Number
Serial Number
E-mail Address*
* Please provide your e-mail address to receive, via e-mail, discounts, special offers and other
important communications from GE Appliances (GEA).
■■ Check here if you do not want to receive communications from GEA’s carefully selected
partners.
FAILURE TO COMPLETE AND RETURN THIS CARD DOES NOT DIMINISH YOUR
WARRANTY RIGHTS.
For information about GEA’s privacy and data usage policy, go to ge.com and click on “Privacy
Policy” or call 800.626.2224.
GE Consumer & Industrial
Appliances
General Electric Company
Louisville, KY 40225
ge.com
Page 23
What GE Will Not Cover:
For The Period Of: GE Will Replace:
One Year Any part of the dryer which fails due to a defect in materials or workmanship. During this
From the date of the limited one-year warranty, GE will also provide, free of charge, all labor and related service costs
original purchase to replace the defective part.
23
■ Service trips to your home to teach you how to
use the product.
■ Improper installation (including improper venting),
delivery or maintenance.
■ Failure of the product if it is abused, misused, or
used for other than the intended purpose or used
commercially.
■ Replacement of the light bulb.
■ Products which are not defective or broken, or which
are working as described in the Owner’s Manual.
■ Replacement of house fuses or resetting of circuit
breakers.
■ Damage to the product caused by accident, fire, floods
or acts of God.
■ Incidental or consequential damage caused by possible
defects with this appliance.
■ Defects or damage due to operation in freezing
temperatures.
■ Damage caused after delivery.
■ Product not accessible to provide required service.
This warranty is extended to the original purchaser and any succeeding owner for products purchased for home
use within the USA. If the product is located in an area where service by a GE Authorized Servicer is not available,
you may be responsible for a trip charge or you may be required to bring the product to an Authorized GE Service
location for service. In Alaska, the warranty excludes the cost of shipping or service calls to your home.
Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives
you specific legal rights, and you may also have other rights which vary from state to state. To know what your
legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.
Warrantor: General Electric Company. Louisville, KY 40225
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions
All warranty service provided by our Factory Service Centers,
or an authorized Customer Care
®
technician. To schedule service,
on-line, 24 hours a day, visit us at ge.com, or call 800.GE.CARES
(800.432.2737). Please have serial number and model number
available when calling for service.
Staple your receipt here.
Proof of the original purchase
date is needed to obtain service
under the warranty.
GE Dryer Warranty.
EXCLUSION OF IMPLIED WARRANTIES—Your sole and exclusive remedy is product repair as provided in this
Limited Warranty. Any implied warranties, including the implied warranties of merchantability or fitness for a
particular purpose, are limited to one year or the shortest period allowed by law.
Page 24
Printed in Canada
GE Appliances Website ge.com
Have a question or need assistance with your appliance? Try the GE Appliances Website 24 hours a day,
any day of the year! For greater convenience and faster service, you can now download Owner’s Manuals,
order parts, catalogs, or even schedule service on-line. You can also “Ask Our Team of Experts™”
your questions, and so much more...
Schedule Service ge.com
Expert GE repair service is only one step away from your door. Get on-line and schedule your service at
your convenience 24 hours any day of the year! Or call 800.GE.CARES (800.432.2737) during normal
business hours.
Real Life Design Studio ge.com
GE supports the Universal Design concept—products, services and environments that can be used by
people of all ages, sizes and capabilities. We recognize the need to design for a wide range of physical and
mental abilities and impairments. For details of GE’s Universal Design applications, including kitchen
design ideas for people with disabilities, check out our Website today. For the hearing impaired, please call
800.TDD.GEAC (800.833.4322).
Extended Warranties ge.com
Purchase a GE extended warranty and learn about special discounts that are available while your warranty
is still in effect. You can purchase it on-line anytime, or call 800.626.2224 during normal business hours.
GE Consumer Home Services will still be there after your warranty expires.
Parts and Accessories ge.com
Individuals qualified to service their own appliances can have parts or accessories sent directly to their
homes (VISA, MasterCard and Discover cards are accepted). Order on-line today, 24 hours every day or
by phone at 800.626.2002 during normal business hours.
Instructions contained in this manual cover procedures to be performed by any user. Other servicing generally
should be referred to qualified service personnel. Caution must be exercised, since improper servicing may cause
unsafe operation.
Contact Us ge.com
If you are not satisfied with the service you receive from GE, contact us on our Website with all the details
including your phone number, or write to: General Manager, Customer Relations
GE Appliances, Appliance Park
Louisville, KY 40225
Register Your Appliance ge.com
Register your new appliance on-line—at your convenience! Timely product registration will allow for
enhanced communication and prompt service under the terms of your warranty, should the need arise.
You may also mail in the pre-printed registration card included in the packing material.
Consumer Support.
Loading...