GE LBB 1965, SV-B8B11D, DR-C91D1N, LBB 1903/10, LBB 1906/10 User Manual
...
TELEPHONE JACK REQUIREMENTS
To use this phone, you need an RJ11C
type modular telephone jack, which
might look like the one pictured here,
installed in your home. If you don’t
have a modular jack, call your local
phone company to find out how to
get one installed.
DIGITAL SECURITY SYSTEM
Your cordless phone uses a digital security system to
provide protection against false ringing, unauthorized
access, and charges to your phone line.
INSTALLING THE PHONE
INSTALLATION NOTE: Some cordless telephones
operate at frequencies that may cause interference to
nearby TVs, microwave ovens, and VCRs. To minimize
or prevent such interference, the base of the cordless
telephone should not be placed near or on top of a
TV, microwave ovens, or VCR. If such interference
continues, move the cordless telephone farther away
from these appliances.
NOTE : You must charge the handset face up.
EQUIPMENT APPROVAL INFORMATION
Your telephone equipment is approved for connection to the Public Switched Telephone
Network and is in compliance with parts 15 and 68, FCC Rules and Regulations and the
Technical Requirements for Telephone Terminal Equipment published by ACTA.
1 Notification to the Local Telephone Company
On the bottom of this equipment is a label indicating, among other information, the US
number and Ringer Equivalence Number (REN) for the equipment. You must, upon
request, provide this information to your telephone company.
The REN is useful in determining the number of devices you may connect to your
telephone line and still have all of these devices ring when your telephone number is
called. In most (but not all) areas, the sum of the RENs of all devices connected to one
line should not exceed 5. To be certain of the number of devices you may connect to
your line as determined by the REN, you should contact your local telephone company.
A plug and jack used to connect this equipment to the premises wiring and telephone
network must comply with the applicable FCC Part 68 rules and requirements adopted
by the ACTA. A compliant telephone cord and modular plug is provided with this
product. It is designed to be connected to a compatible modular jack that is also
compliant. See installation instructions for details.
Notes
• This equipment may not be used on coin service provided by the telephone company.
• Party lines are subject to state tariffs, and therefore, you may not be able to use
your own telephone equipment if you are on a party line. Check with your local
telephone company.
• Notice must be given to the telephone company upon permanent disconnection of
your telephone from your line.
• If your home has specially wired alarm equipment connected to the telephone line,
ensure the installation of this product does not disable your alarm equipment. If you
have questions about what will disable alarm equipment, consult your telephone
company or a qualified installer.
2 Rights of the Telephone Company
Should your equipment cause trouble on your line which may harm the telephone network,
the telephone company shall, where practicable, notify you that temporary discontinuance of
service may be required. Where prior notice is not practicable and the circumstances
warrant such action, the telephone company may temporarily discontinue service
immediately. In case of such temporary discontinuance, the telephone company must: (1)
promptly notify you of such temporary discontinuance; (2) afford you the opportunity to
correct the situation; and (3) inform you of your right to bring a complaint to the Commission
pursuant to procedures set forth in Subpart E of Part 68, FCC Rules and Regulations.
The telephone company may make changes in its communications facilities, equipment,
operations or procedures where such action is required in the operation of its business and
not inconsistent with FCC Rules and Regulations. If these changes are expected to affect the
use or performance of your telephone equipment, the telephone company must give you
adequate notice, in writing, to allow you to maintain uninterrupted service.
FCC RF RADIATION EXPOSURE STATEMENT
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of
20 centimeters between the radiator and your body. This transmitter must not be co-located
or operated in conjunction with any other antenna or transmitter.
NOTE: The phone automatically defaults to touchtone dialing. To change to pulse (rotary) dialing,
see "Tone/Pulse Dialing." If you don't know which
type of service you have, check with your local
telephone company.
SET UP
There are five programmable menus available:
Language, Tone/Pulse Dialing, Area Code, Ringer Tone
and Default Setting.
LANGUAGE
1. Make sure the phone is OFF (not in TALK mode).
2. Press the flash/prog button until “
1ENG 2FRA 3ESP
”
shows in the display. “
1ENG
” is the default setting.
3. Use the handset or button or the touch-tone pad to
select
1ENG 2FRA 3ESP
.
4. Press flash/prog again to save. You will hear a
confirmation tone.
TONE/PULSE DIALING
1. Make sure the phone is OFF (not in TALK mode).
2. Press the flash/prog button until “
1TONE 2PULSE
”
shows in the display. “
1TONE
” is the default setting.
3. Use the handset or button or the touch-tone pad to
select
1TONE
or
2PULSE
.
4. Press flash/prog again to save. You will hear a
confirmation tone.
AREA CODE
1. Make sure the phone is OFF (not in TALK mode).
2. Press the flash/prog button until “- - -
SET AREA CODE
”
shows in the display. “
- - -”
is the default setting.
3. Use the handset touch-tone pad to enter your three digit
area code.
4. Press flash/prog again to save. You will hear a
confirmation tone.
RINGER TONE
1. Press the flash/prog button until
RINGER TONE 1
shows
in the display. There are seven ringer tones to choose
from. 1 is the default setting.
2. Use the handset up or down button or the touch-tone
pad to select a ringer tone. The ringer tone plays.
3. Press flash/prog again to save. You will hear a
confirmation tone.
DEFAULT SETTING SELECTION
1. Press the flash/prog button until
DEFAULT SETTING
shows in the display.
1NO
is the default setting.
2. Use the handset up or down button or the touch-tone
pad to select
1 NO
or
2 YES
. If you choose
1NO
, the
current settings remain. If you choose
2YES
, the unit
resets to the factory default.
3. Press flash/prog again to confirm.
TELEPHONE OPERATION
CLOCK
BACKLIGHT
Press the BKLITE button once to turn it off; press BKLITE
again to turn it back on.
SETTING THE HOUR
1. Press and hold the HOUR button until the hour
hand flashes.
2. Press the HOUR button to rotate the hour hand.
NOTE: To make the hour hand rotate faster, hold
down the HOUR button.
3. Release the HOUR button when you reach the desired
hour. The hour hand stops flashing and the new time
is set.
SETTING THE MINUTES
1. Press and hold the MINUTE button until the minute
hand flashes.
2. Press the MINUTE button to rotate the minute hand.
NOTE: To make the hour hand rotate faster, hold
down the MINUTE button.
3. Release the MINUTE button when you reach the
desired minute.
4. The minute hand shall stop flashing and the new time
is set.
MAKING A CALL
1. Press the TALK/CALLBACK button on the handset
receiver or the SPKR/CALLBACK button on the
speakerphone to get a dial tone. Or dial the telephone
number first, and then press the TALK/CALLBACK or
SPKR/CALLBACK button.
2. When finished, press TALK/CALLBACK or SPKR/
CALLBACK again to hang up.
ANSWERING A CALL
1. When the phone rings, pick up the handset and press
the TALK/CALLBACK button. Or press the SPKR/
CALLBACK button to use the speakerphone.
2. When finished, press TALK/CALLBACK or SPKR/
CALLBACK again to hang up.
MUTE
To have a private, off-line conversation use the mute
feature. The party on the telephone line will not hear you,
but you can still hear them.
1. Press the MUTE/FORMAT button on the handset.
MUTE
ON
shows in the display.
2. Press the MUTE/FORMAT button again to cancel mute
and return to your phone conversation.
REDIAL
While the phone is on, press the REDIAL button to REDIAL
the last number you dialed (up to 32 digits). If you get a
busy signal, and want to keep dialing the number, just
press REDIAL again (you don't have to turn the phone off
and back on).
FLASH
Use the flash/prog button to activate custom calling
services such as call waiting or call transfer, which
are available through your local phone company.
TIP: Don’t use the TALK/CALLBACK button to
activate custom calling services such as call waiting, or
you’ll hang up the phone.
IN USE INDICATOR LIGHT
The in use indicator is lit when the handset is charging in the
cradle on the base or when the phone is ON. It flashes when
you receive a call or when the PAGE button is pressed.
TEMPORARY TONE DIALING
This feature is useful only if you use pulse dialing service.
Temporary tone dialing enables pulse (rotary) service
phone users to access touch-tone services offered by
banks, credit card companies, etc. For example, when you
call your bank you may need to enter your account
number. Using the temporary tone feature allows you to
temporarily switch to touch-tone mode so you can enter
and send your number.
1. Press the TALK/CALLBACK button, dial the telephone
number (i.e. bank or credit card company), and wait for
the line to connect.
2. When your call is answered, press the *tone/exit button
on your handset number pad to temporarily change
from pulse dialing to tone dialing.
3. Follow the automated instructions to get the
information you need.
4. Hang up the handset and the phone automatically
returns to pulse (rotary) dialing mode.
EXIT
Press the *tone/exit button to cancel any command
you initiated.
PAGING THE HANDSET
To locate a misplaced handset.
1. Press the PAGE button on the base. The handset beeps.
2. When you locate the handset, press any button on the
handset, or press the base PAGE button to cancel
NOTE: The ringer does not have to be ON for this
feature to work.
RINGER SWITCH
The ringer switch must be ON for the handset to ring
during incoming calls.
VOLUME
While talking, press the CID/VOL and buttons to
adjust the listening level of the handset’s earpiece. There
are four volume levels. Press the button to increase the
volume level, and press the button to decrease. VOL 1 is
the lowest level and VOL 4 is the loudest.
CALL TIMER
The built-in call timer shows in the display and counts the
call time in minutes and seconds.
CALLER ID
This unit receives and displays information transmitted by
your local phone company. This information can include
the phone number, date, and time; or the name, phone
number, date, and time. The unit can store up to 40 calls
for later review.
CALLER ID WITH CALL WAITING
Provided you subscribe to Caller ID with Call Waiting
service from your phone company, you are able to see who
is calling when you hear the call waiting beep. The caller
identification information appears in the display after you
hear the tone.
•Press the flash/prog button to put the current person on
hold so that you can answer the incoming call.
IMPORTANT: In order to use the Caller ID functions
with this unit, you must subscribe to either the
standard Name/Number Caller ID Service or Call
Waiting Caller ID Service. To know who is calling while
you are on the phone, you must subscribe to Call
Waiting Caller ID Service.
RECEIVING AND STORING CALLS
When you receive a call, the information is transmitted by
the phone company to your Caller ID telephone between
the first and second ring.
When the memory is full, a new call automatically replaces
the oldest call in memory.
NEW
appears in the display for
calls received that have not been reviewed.
REPT
indicates
that a new call from the same number was received more
than once.
NOTE: Check with your local phone company
regarding name service availability.
REVIEWING RECORDS
As calls are received and stored, the display is updated to
let you know how many calls have been received.
•Press the button to scroll through the call records
from the most recent to the oldest.
•Press the button to scroll through the call records
from the oldest to the newest.
TRANSFERRING CID RECORDS
TO
MEMORY
You may transfer a Caller ID record to your phone’s memory.
NOTE: It is important that you format CID records
correctly before storing in memory. It is not possible to
re-format CID records stored in memory.
1. Use the or button to scroll to the record.
2. Press the mem button.
3. Press the memory location button. You will hear a
confirmation tone. For example, press the number 1 key
to store the record in memory location 1.
To r eplace a CID record stored in a memory location with a
new CID record:
1. Repeat steps 1 through 3.
2. Press the mem button and
REPLACE MEMO?
shows in
the display.
3. Press *tone/exit to exit, or press mem again and the
new CID record replaces the old CID record in that
memory location. You will hear a confirmation tone.
DELETING RECORDS
Use the del button to erase the record currently shown in
the display or all records.
DELETING THE CURRENT RECORD
1. Make sure the phone is OFF (not in TALK mode).
2. Use the or button to scroll to the Caller ID record
you want to delete.
3. Press del button. The display shows
DELETE?
4. Press del again to erase the record. You will hear a
confirmation tone. The display shows
DELETED
. Then
the next Caller ID record shows in the display.
DELETING ALL RECORDS
1. Make sure the phone is OFF (not in TALK mode).
2. Use the or button to display any Caller ID record.
3. Press and hold the del button until the unit beeps and
DELETE ALL?
shows in the display.
4. Press del again to erase all records. You will hear a
confirmation tone, and the display shows
NO CALLS
.
DIALING A CALLER ID NUMBER
1. Make sure the phone is OFF (not in TALK mode).
2. Use the or button to display the Caller ID record
you want to dial.
3. Press TALK/CALLBACK or SPKR/CALLBACK button. The
number dials automatically.
CHANGING THE CID NUMBER FORMAT
The format button lets you change the format of the
displayed CID number. The available formats are as follows.
7-digit 7-digit telephone number.
10-digit 3-digit area code + 7-digit telephone number.
11-digit long distance code “1” + 3-digit area code +
7-digit telephone number.
1. Use the or button to scroll to the number you want
to call back.
2. If the number does not dial as shown, press the format
button. Repeat if necessary, until the correct number of
digits show in the display.
3. Press TALK/CALLBACK or SPKR/CALLBACK button. The
number dials automatically.
22430
2.4 GHz Cordless Caller ID
Telephone with Digital Clock and
Handset Speakerphone
User's Guide
We bring good things to life.
ATLINKS USA, Inc.
101 West 103rd Street
Indianapolis, IN 46290
© 2004 ATLINKS USA, Inc.
Trademark(s) ® Registered
Marca(s) ® Registrada(s)
Model 22430A
16333710 (Rev. 0 DOM E)
04-08
Printed in China
SEE MARKING ON BOTTOM / BACK OF PRODUCT
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO
PREVENT FIRE OR
ELECTRICAL SHOCK
HAZARD, DO NOT
EXPOSE THIS
PRODUCT TO RAIN
OR MOISTURE.
THE LIGHTNING
FLASH AND ARROW
HEAD WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
“DANGEROUS
VOLTAGE” INSIDE
THE PRODUCT.
CAUTION: TO REDUCE THE
RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR
BACK). NO USER
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO
QUALIFIED SERVICE
PERSONNEL.
THE EXCLAMATION
POINT WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
IMPORTANT
INSTRUCTIONS
ACCOMPANYING
THE PRODUCT.
CAUTION:
Base
Handset
AC power
converter
Telephone
line cord
REDIAL button
mem button
del button
ringer switch
SPKR/CALL
BACK button
MUTE/FORMAT
button
flash/prog
button
display
* tone/exit
button
# PAUSE
button
Belt Clip
Modular
telephone
line jack
Wall plate
For body worn operation, this phone has been tested and meets the FCC RF exposure
guidelines when used with the belt clip supplied with this product. Use of other accessories
may not ensure compliance with FCC RF exposure guidelines.
HEARING AID COMPATIBILITY (HAC)
This telephone system meets FCC standards for Hearing Aid Compatibility.
US NUMBER IS LOCATED ON THE CABINET BOTTOM
REN NUMBER IS LOCATED ON THE CABINET BOTTOM
INTRODUCTION
CAUTION: When using telephone equipment,
there are basic safety instructions that should
always be followed. Refer to the IMPORTANT
SAFETY INSTRUCTIONS provided with this
product and save them for future reference.
Your Caller ID phone stores and displays specific information,
provided by your local telephone company, to subscribers of
Caller ID or similar caller identification services.
Your Caller ID phone enables you to:
• Identify callers before you answer the phone.
•View the time and date of each incoming call.
•Record up to 40 Caller ID messages sequentially.
• Know who called while you were away.
To get the most from your new phone, we suggest that
you take a few minutes right now to read through this
user's guide.
IMPORTANT: In order to use all of the features of
this phone, you must subscribe to the standard Name/
Number Caller ID Service.
IMPORTANT: Because cordless phones operate on
electricity, you should have at least one phone in your
home that isn’t cordless, in case the power in your
home goes out.
HANDSET AND BASE LAYOUT
BEFORE YOU BEGIN
PARTS CHECKLIST
Make sure your package includes the items shown here.
1. Choose an area near an electrical outlet and telephone
wall jack (RJ11C). Your phone should be placed on a
level surface, such as a table top or desk.
2. Set the RINGER switch (on the handset) to ON and place
the handset in the cradle on the base.
3. Plug the AC power converter into an electrical outlet and
DC connector into the power jack on the back of the
base. The in use/charge indicator comes on, verifying
the battery is charging.
CAUTION: Use only the ATLINKS USA, Inc.
5-2636 power converter that came with this
unit. Using other power converters may damage
the unit.
4. Allow the phone to charge for 12 hours prior to first use.
If you don't properly charge the phone, battery
performance will be compromised.
NOTE: DO NOT connect the telephone line to the
modular jack until the phone has charged for 12 hours.
5. Plug one end of the telephone line cord into the PHONE
LINE jack on the back of the base and the other end into
a modular jack.
NEW CALL #
Caller ID nameCaller ID phone number
Time
Date
New call
Battery
compartment
cover
Battery
TALK/CALL
BACK button
CID/VOL arrow
up down button
charge/ in use
button
page button
BKLITE button
HOUR button
MINUTE button
Please make sure that this form has been filled out completely.
To order, call 1-800-338-0376 (for accessories only) or
complete this order form.
Copy your complete account number from your
Master Card or Discover.
____________________________________________________________________
Authorized Signature
My card expires:
Copy the number above your
name on the Master Card.
For credit card purchases
Your complete charge card number, its expiration date and your
signature are necessary to process all charge card orders.
Copy your complete account number from your VISA card.
My card expires:
*Prices are subject to change without notice.
Total Merchandise.........................................$_______________
Sales Tax........................................................$_______________
We are required by law to collect the appropriate sales tax for each individual state,
county, and locality to which the merchandise is being sent. Duties will apply for
shipments to Canada.
Use VISA or Master Card or Discover preferably. Money order or check must be in U.S.
currency only. No COD or Cash. All accessories are subject to availability. Where
applicable, we will ship a superseding model.
Shipping/Handling....................................... $_______________
Total Amount Enclosed.................................$_______________
Mail order form and money order or check (in U.S. currency)
made payable to Thomson to:
Thomson
Mail Order Department
P.O. Box 910139
Dallas, TX 75391-0139
Name_______________________________________________________
Address_____________________________________ Apt.____________
City ________________________State________ ZIP_________________
Daytime Phone Number ( )_______________________________
$5.00
MEMORY
Store up to 10 24-digit numbers in memory for quick
dialing. This memory feature is in addition to the 40 Caller
ID records that can be stored in the Caller ID memory log.
STORING A NAME AND NUMBER IN
MEMORY
1. Make sure the phone is OFF (not in TALK mode).
2. Press the mem button.
3. Press the memory location button (0 through 9 keys).
4. Press the mem button again. The display shows
ENTER
NAME
(up to 15 characters).
NOTE: If you don't want to enter the name, skip to step 5.
For example, to enter the name Bill Smith, press the two
key twice for the letter B, press the four key three times
for the letter I, and press the five key three times for the
letter L. After one second, press the five key three times
again for the second letter L and press the one key to
insert a space between the letter L and S. Press the
seven key four times for the letter S, press the six key
once for the letter M, press the four key three times for
the letter I, press the eight key once for the letter T, and
press the four key twice for the letter H.
NOTE: If you make a mistake, press the del button to
erase a wrong letter, and re-enter the correct letter.
5. Press the mem button to save the name. The display
shows
ENTER TEL NUMBR
.
6. Use the handset touch-tone pad to enter the telephone
number (up to 24 digits) you want to store.
7. Press mem again to store the number. You will hear a
confirmation tone.
CHANGING A STORED NUMBER
1. Repeat steps 1 through 7 in Storing a Name and
Number in Memory.
2. Press the mem button and
REPLACE MEMO?
shows in
the display.
3. Press *tone/exit to exit, or press the mem button to
store the number. You will hear a confirmation tone.
STORING A REDIAL NUMBER
1. Repeat steps 1 through 6 in Storing a Name and
Number in Memory.
2. Press the REDIAL button.
3. Press the mem button to store the number. You will hear
a confirmation tone.
To r eplace an old redial number stored in a memory
locations with a new redial number:
1. Repeat steps 1 through 6 in Storing a Name and
Number in Memory.
2. Press the mem button and
REPLACE MEMO?
shows in
the display.
3. Press *tone/exit to exit, or press the mem button again
and the new redial number replaces the old redial
number in that memory location. You will hear a
confirmation tone.
DIALING A STORED NUMBER
1. Make sure the phone is ON by pressing the TALK/
CALLBACK button.
2. Press the mem button.
3. Press the memory location button (0 through 9 keys).
The number dials automatically.
- OR -
1. Make sure the phone is OFF (not in TALK mode).
2. Press mem button.
3. Use the or button to scroll to the number you want
to dial.
4. Press TALK/CALLBACK or SPKR/CALLBACK button. The
numbers dial automatically.
IMPORTANT: If you make test calls to emergency
numbers stored in memory, remain on the line and
briefly explain the reason for the call to the dispatcher.
Also, it’s a good idea to make these calls in off-peak
hours, such as early morning or late evening.
INSERTING A PAUSE IN THE DIALING
SEQUENCE OF A STORED NUMBER
When a pause is needed to wait for a dial tone, press the #
pause button twice within one second (for example, when
you must dial 9 for an outside line or to wait for a
computer access tone.) A “pause” in the dialing sequence
shows in the display as a “
P .
” Each pause counts as 1
digit in the dialing sequence.
REVIEWING AND DELETING STORED
NUMBERS
1. Press the mem button.
2. Use the or button to scroll to the number.
3. To delete the number, press the del button. The display
shows
DELETE?
4. Press del again to delete the number.
DELETED
shows
in the display.
CHAIN DIALING FROM MEMORY
Use this feature to make calls which require a sequence of
numbers such as using a calling card for a frequently
called long distance number. Basically, you dial each part
of the sequence from memory. The following example
shows how you can use chain dialing to make a call
through a long distance service:
The Number For Memory Location
Long distance access number 7
Authorization code 8
Frequently called long distance number 9
1. Make sure the phone is ON.
2. Press mem and then press 7.
3. When you hear the access tone, press mem again and
then press 8.
4. At the next access tone, press mem and then 9.
TIP: Wait for the access tones between pressing the
mem button, or your call might not go through.
HEADSET AND BELT CLIP
OPERATION
CONNECTING AN
OPTIONAL HEADSET
TO
THE HANDSET
For hands free conversation.
1. Connect the headset (optional)
to the HEADSET jack as shown.
The handset receiver and
microphone are disabled when
the headset is connected.
TIP: To order a headset, please refer to the accessory
order form at the end of this user’s guide.
2. Adjust the headset to rest comfortably on top of your
head and over your ear. Move the microphone to
approximately 2 to 3 inches from your mouth.
3. Press the TALK/CALLBACK button to answer or place
a call.
4. To return to normal operation, unplug the headset from
the jack.
ATTACHING THE BELT
CLIP
1. Insert the sides of the belt clip
into the slots on each side of the
handset.
2. Snap the ends of the belt clip into place.
REPLACING THE BATTERY
1. Make sure the telephone is OFF (not in TALK mode)
before you replace battery.
2. Remove the battery compartment door.
3. Disconnect the cord attached to the
battery pack from the jack inside the
battery compartment and remove the
battery pack.
4. Insert the new battery pack and connect
the plug on the battery pack to the jack
inside the compartment.
5. Put the battery compartment door
back on.
6. Place the handset in the base to charge.
Allow the handset battery to properly charge (for 12 hours)
prior to first use or when you install a new battery pack. If
you do not properly charge the phone, battery performance
will be compromised.
CAUTION: To reduce the risk of fire or personal
injury, use only the battery 5-2637.
BATTERY SAFETY PRECAUTIONS
• Do not burn, disassemble, mutilate, or puncture. Like
other batteries of this type, toxic materials could be
released which can cause injury.
•To reduce the risk of fire or personal injury, use only the
battery listed in the User’s Guide.
•Keep batteries out of the reach of children.
•Remove batteries if storing over 30 days.
DISPLAY MESSAGES
The following indicators show the status of a message or
of the unit.
INCOMPLETE DATA Caller information has been
interrupted during transmission or
the phone line is excessively noisy.
ENTER NAME Prompt telling you to enter the
name for one of the 10 memory
locations.
ENTER TEL NUMBR Prompt telling you to enter the
telephone number for one of the
10 memory locations.
DELETE? Prompt asking if you want to erase
Caller ID records or one of the 10
numbers stored in the phone’s
outgoing memory.
DELETE ALL? Prompt asking if you want to erase
all Caller ID records.
DELETED Prompt confirming the Caller ID /
Memory record is erased.
END OF LIST Indicates there is no additional
information in Caller ID memory.
NEW Indicates call or calls have not
been reviewed.
MUTE ON Indicates you are muting a
telephone conversation to speak
to an third party .
TALK 00:00 VOL1 Indicates the handset earpiece
is active.
SPKR 00:00 VOL1 Indicates the handset
speakerphone is turned on.
UNKNOWN NAME/ The incoming call is from
CALLER/NUMBER an area not serviced by Caller ID
or the information was not sent.
PAGING Someone has pressed the page
button on the base.
BLOCKED CALL The person is calling from a
number that has been blocked
from transmission.
BLOCKED NAME The person’s name is blocked
from transmission.
REPT Repeat call message. Indicates that
a new call from the same number
was received more than once.
NO DATA No Caller ID information was
received.
EMPTY Indicates a memory location
is vacant.
NO CALLS Indicates no CID records have
been stored.
MESSAGE WAITING Indicates a message is available.
HANDSET SOUND SIGNALS
Signal Meaning
A long warbling tone Signals an incoming call
(with ringer on)
Two long beeps Confirmation Tone
One short and one long beep Page signal
One short beep Low battery warning
every seven seconds
TROUBLESHOOTING TIPS
CALLER ID
No display
• Make sure the battery is properly charged for 12 hours.
• Make sure the battery is properly installed and connected.
•Replace the battery. Make sure the unit is connected to a
non-switched electrical outlet.
• Disconnect the unit from the electrical outlet and plug it
back in.
• Make sure you are subscribed to Caller ID service from
your local telephone company.
Caller ID error message
• The unit displays this message if it detects anything
other than valid Caller ID information during the silent
period after the first ring. This message indicates the
presence of noise on the line.
TELEPHONE
No dial tone
• Check or repeat installation steps.
• Make sure the base power converter is connected to a
working electrical outlet.
• Make sure the telephone line cord is connected to the
base and the wall jack.
• Disconnect the base from the wall jack and connect
another phone to the same jack. If there is no dial tone
in the second phone, the problem might be your wiring
or local service.
• The handset may be out of range. Move closer to the base.
• Make sure the battery is properly charged (for 12 hours).
• Make sure the battery pack is installed correctly.
• Did the handset beep when you pressed the TALK/
CALLBACK button? Did the display indicator turn on?
The battery may need to be charged.
Dial tone is OK, but can't dial out
• Make sure the tone/pulse setting is programmed correctly.
Handset does not ring
• Make sure the ringer switch on the handset is turned ON.
•You may have too many extension phones on your line.
Try unplugging some phones.
•See solutions for “No dial tone.”
In use/charge indicator on the base flashes
•Provided your phone company offers voice messaging
service and you subscribe to it, the in use/charge
indicator on the base flashes when the phone is not in
use to indicate there is a message waiting. It stops
flashing after the message has been reviewed.
You experience static, noise, or fading in and out
• Handset may be out of range. Move closer to the base.
•Relocate the base
• Charge the battery.
• Make sure the base is not plugged into an outlet with
another household appliance.
Unit beeps
•See solutions for “No dial tone.”
•Replace the battery.
Memory dialing
• Make sure you have correctly programed the memory keys.
• Make sure to follow proper dialing sequence.
CUSTOMER: CUT ALONG DOTTED LINE.
✂
DESCRIPTION
MODEL NO.
TOTAL
QTY.
PRICE*
Belt clip
$10.85
Headset
$36.35
$9.95
Replacement battery
ACCESSORY ORDER FORM
5-2635
5-2588
5-2637
$24.95
Power supply
5-2636
• Make sure the tone/pulse setting is programmed correctly.
• If you had a power outage or replaced the battery,
reprogram the numbers into memory.
S
ERVICE
If trouble is experienced with this equipment, for repair or
warranty information, please contact customer service at
1-800-448-0329. If the equipment is causing harm to the
telephone network, the telephone company may request that
you disconnect the equipment until the problem is resolved.
This product may be serviced only by the manufacturer or
its authorized service agents. Changes or modifications not
expressly approved by ATLINKS USA, Inc. could void the
user’s authority to operate this product. For instructions on
how to obtain service, refer to the warranty included in this
guide or call customer service at 1-800-448-0329.
Or refer inquiries to:
ATLINKS USA, Inc.
Manager, Consumer Relations
P O Box 1976
Indianapolis, IN 46206
Attach your sales receipt to the booklet for future reference
or jot down the date this product was purchased or
received as a gift. This information will be valuable if
service should be required during the warranty period.
Purchase date _________________________________________
Name of store _________________________________________
GENERAL PRODUCT CARE
To keep your telephone working and looking good, follow
these guidelines:
•Avoid putting the phone near heating appliances and
devices that generate electrical noise (for example,
motors or fluorescent lamps).
• DO NOT expose to direct sunlight or moisture.
•Avoid dropping and other rough treatment to the phone.
•Clean with a soft cloth.
• Never use a strong cleaning agent or abrasive powder
because this will damage the finish.
•Retain the original packaging in case you need to ship
the phone at a later date.
CAUSES OF POOR RECEPTION
• Aluminum siding.
•Foil backing on insulation.
• Heating ducts and other metal construction can shield
radio signals.
•You’re too close to appliances such as microwaves,
stoves, computers, etc.
• Atmospheric conditions, such as strong storms.
• Base is installed in the basement or lower floor of
the house.
•Base is plugged into an AC outlet with other
electronic devices.
•Baby monitor is using the same frequency.
• Handset battery is low.
•You’re out of range of the base.
INTERFERENCE INFORMATION
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference; and (2)
This device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio
or television reception, which can be determined by
turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the
following measures:
•Reorient or relocate the receiving antenna (that is, the
antenna for radio or television that is “receiving” the
interference).
•Reorient or relocate and increase the separation
between the telecommunications equipment and
receiving antenna.
• Connect the telecommunications equipment into an
outlet on a circuit different from that to which the
receiving antenna is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
If these measures do not eliminate the interference, please
consult your dealer or an experienced radio/television
technician for additional suggestions. Also, the Federal
Communications Commission has prepared a helpful
booklet, “How To Identify and Resolve Radio/TV
Interference Problems.” This booklet is available from the
U.S. Government Printing Office, Washington, D.C. 20402.
Please specify stock number 004-000-00345-4 when
ordering copies.
LIMITED WARRANTY
What your warranty covers:
• Defects in materials or workmanship.
For how long after your purchase:
• One year, from date of purchase. (The warranty period for rental
units begins with the first rental or 45 days from date of shipment
to the rental firm, whichever comes first.)
What we will do:
• Provide you with a new or, at our option, a refurbished unit. The
exchange unit is under warranty for the remainder of the original
product’s warranty period.
How you get service:
• Properly pack your unit. Include any cables, etc., which were
originally provided with the product. We recommend using the
original carton and packing materials.
• ”Proof of purchase in the form of a bill of sale or receipted
invoice which is evidence that the product is within the warranty
period, must be presented to obtain warranty service.” For rental
firms, proof of first rental is also required. Also print your name
and address and a description of the defect. Send via standard
UPS or its equivalent to:
ATLINKS USA, Inc.
c/o Thomson
11721 B Alameda Ave.
Socorro, Texas 79927
• Pay any charges billed to you by the Exchange Center for service
not covered by the warranty.
• Insure your shipment for loss or damage. ATLINKS accepts no
liability in case of damage or loss.
•A new or refurbished unit will be shipped to you freight prepaid.
What your warranty
does not
cover:
• Customer instruction. (Your Owner’s Manual provides information
regarding operating instructions and user controls. Any additional
information, should be obtained from your dealer.)
• Installation and setup service adjustments.
• Batteries.
• Damage from misuse or neglect.
• Products which have been modified or incorporated into other
products.
• Products purchased or serviced outside the USA.
• Acts of nature, such as but not limited to lightning damage.
Product Registration:
• Please complete and mail the Product Registration Card
packed with your unit. It will make it easier to contact you
should it ever be necessary. The return of the card is not
required for warranty coverage.
Limitation of Warranty:
• THE WARRANTY STATED ABOVE IS THE ONLY WARRANTY
APPLICABLE TO THIS PRODUCT. ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED (INCLUDING ALL IMPLIED WARRANTIES
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE) ARE HEREBY DISCLAIMED. NO VERBAL OR WRITTEN
INFORMATION GIVEN BY ATLINKS USA, INC., ITS AGENTS, OR
EMPLOYEES SHALL CREATE A GUARANTY OR IN ANY WAY
INCREASE THE SCOPE OF THIS WARRANTY.
NOTE: The RBRC seal on the battery
used in your ATLINKS USA, Inc.
product indicates that we are
participating in a program to collect
and recycle Nickel Cadmium batteries
throughout the United States. Please
call 1-800-8-BATTERY for information
or contact your local recycling center.
Ni-Cd
R
B
R
C
R
B
R
C
•REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS
WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER.
ATLINKS USA, INC. SHALL NOT BE LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS
PRODUCT OR ARISING OUT OF ANY BREACH OF ANY EXPRESS
OR IMPLIED WARRANTY ON THIS PRODUCT. THIS DISCLAIMER
OF WARRANTIES AND LIMITED WARRANTY ARE GOVERNED BY
THE LAWS OF THE STATE OF INDIANA. EXCEPT TO THE EXTENT
PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE
ON THIS PRODUCT IS LIMITED TO THE APPLICABLE WARRANTY
PERIOD SET FORTH ABOVE.
How state law relates to this warranty:
•Some states do not allow the exclusion nor limitation of incidental
or consequential damages, or limitations on how long an implied
warranty lasts so the above limitations or exclusions may not
apply to you.
• This warranty gives you specific legal rights, and you also may
have other rights that vary from state to state.
If you purchased your product outside the USA:
• This warranty does not apply. Contact your dealer for
warranty information.
Headset jack
Headset plug
Slot for
belt clip
Slot for
belt clip
Loading...