GE DLL6850B, DLB6850B Use and Care Manual

Page 1
How
Center@
Contents
to
get
the
best from
Appliance Registration Automatic Drying
Care and Cleaning Controls Setting Guide
Dryer Exhaust Energy-Saving Tips
Knits Drying Tips Lint Filter
Loading Model and Serial Numbers
Operating the Dryer
Perm. Press Drying Tips 5-7, 11, 12
Problem Solver Repair Service
Safety Instructions Sorting
Storing Dryer
Timed Drying User Maintenance Instructions 13
Warranty
Back Cover
13
6,7
13
5-7, 11
5,9, 13
5,9
10-12
15
3,4 5,8
13
5
Use and Care of
model
DLB6850B DLL6850B
The GE Answer
800.626.2000
Page 2
Help us
help you...
Before using your dryer, read this book carefully.
It is intended to help you operate and maintain your new dryer properly.
Keep it handy for answers to your questions.
If you don’t understand something or need more help, write (include
your phone number): Consumer Affairs
Hotpoint
Appliance Park Louisville,
KY40225
If you received a damaged dryer. . .
Immediately contact the dealer
(or builder) that sold you the
dryer.
Save time and money.
Before you request service . . .
check the Problem Solver on pages 10-12. It lists causes of minor operating problems that you can correct yourself.
Write down the model and serial numbers.
You’ll find them on a label on the front of the dryer behind the door.
These numbers are also on the Consumer Product Ownership Registration Card that came with your dryer. Before sending in this card, please write these numbers here:
Model Number
Serial Number
Use these numbers in any correspondence or service calls concerning your dryer.
FOR YOUR
SA~TY
If you smell gas:
1. Open windows.
2. Don’t touch electrical switches?
3. Extinguish any open flame.
4. Immediately call your gas supplier.
*Don’t turn electric switches on or off because sparks may ignite the gas.
FOR YOUR SAFETY Do
not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
All drying instruction terms in this book conform to the Care Labeling Rule established by the Federal Trade Commission, January 1984.
2
Page 3
IMPORT~T
F
Read all instructions before using this appliance.
SAFETY INSTRUCTIONS
-
WMING—TO
of fire, electric shock, or injury to persons when using your
apptiance, fo~ow
including the following:
Use this appliance only for its
intended purpose
this Use and Care Book.
This dryer must be properly
installed and located in accordance with the Instillation Instructions before it is used. If
you did not receive an Installation Instructions sheet with your dryer, you can obtain one by contacting the service location nearest you.
—Properly ground to conform with all governing codes and ordinances. Follow details in Instillation Instructions.
—Locate where the temperature is above
50°F. (lO°C.)
satisfactory operation of the dryer control system. Do not install or store the dryer where it will be exposed to the weather.
—Connect to a properly rated, protected and sized power-supply circuit to avoid electrical overload.
—Exhausting to the outside is STRONGLY RECOMMENDED to prevent large amounts of moisture and lint from being blown into the room. Carefully follow the Exhausting Details in the Instigation Instructions.
When disconnecting this appliance pull by the plug rather than the cord to avoid damage to the cord or junction of cord and plug. Make sure that the cord is located so that it will not be stepped on, tripped over or otherwise subjected to damage or stress.
Do not repair or replace any part of the appliance or attempt any servicing unless specifically recommended in this Use and Care Book or in published repair instructions that you understand and have the skills to
carry out.
reduce the risk
basic
p-utions,
as described in
for
user-
To minimize the possibility of a fire hazard.
Do not use heat to dry articles containing rubber, plastic, or similar materials (such as padded bras, tennis shoes, galoshes, bath mats, rugs, bibs, baby pants, plastic bags, etc.) as these materials may melt or burn. Also, some rubber materials, when
certain circumstances produce fire by spontaneous combustion.
Garments labeled “Dry Away
From Heat” (such as life jackets containing Kapok) must not be put in your dryer.
Do not wash or dry articles that have been cleaned in, washed in, soaked in, or spotted with combustible or explosive substanc~ (such as gasoline, degreasers,
drycleaning solvents, kerosene,
which may give off vapors that
cotid
ignite or explode. Do not use or store such substances on/or around your washer and/or dryer during operation.
Any article on which you have used a cleaning solvent, or which contains flammable materials (such as cleaning cloths, mops, towels used in beauty salons, restaurants or barber shops, etc.) must not be placed in or near the dryer until all traces of these flammable liquids or solids and their fumes have been removed. There are many highly flammable items used in homes such as: acetone, denatured alcohol, gasoline, kerosene, some household cleaners, some spot removers, turpentines, waxes, wax removers and products containing petroleum distillates.
Clean the lint filter before each load to prevent lint accumulation inside the dryer or in the room. DO NOT OPERATE THE
DRYER WITHOUT THE LINT FILTER IN PLACE.
. Keep area around and underneath your appliance free
hated,
can under
etc.)
from the accumulation of combustible materials, such as lint, paper, rags, chemicals, etc.
Do not store items that may burn or melt (such as clothing, paper material, plastics or plastic containers, etc. ) on top of the dryer during operation.
The interior of the machine
and the exhaust duct connection inside the dryer should be
cleaned periodically by a qualified individual.
Exhaust duct (see installation
instructions). Use only
metai
duct inside dryer or for exhausting dryer to the outside.
To minimize the possibility of injury.
Never reach into the the drum is moving. Befo;e loading, unloading or adding clothes, wait until the drum has completely stopped.
Close supervision is necessary
if this appliance is used by or near
children. Do not allow children to play inside, on or with this appliance or any discarded appliance. Dispose of discarded
appticw
and shipping or packing materials properly. Before discarding a dryer, or removing from service, remove the door of the drying compartment.
. Keep all laundry aids (such as detergents, bleaches, fabric softeners, etc. ) out of the reach of children, preferably in a locked cabinet. Observe all warnings on container labels to avoid personal injury.
Keep the floor around your appliances clean and dry to reduce the possibility of slipping.
Do not dry fiberglass articles in
your dryer. Skin irritation could result from the remaining glass
particles that may be picked up by clothing during subsequent
drver
while
3
‘ryerusew
Page 4
hportant Safety Imtructiom
(continued)
The laundry process can reduce
the flame retardancy of fabrics. To avoid such a result, the garment manufacturer’s care instructions should be followed very carefully.
Never climb on or stand on the
dryer top or door.
Do not timper with controls.
To minimize the possibility
of electric shock, unplug this
appliance from the power supply
before attempting any maintenance
or cleaning (except the removal and cleaning of the lint filter). Turning the Cycle Selector knob to an OFF position does disconnect the appliance from the power supply.
Do not operate this appliance if it is damaged, malfunctioning, partially disassembled, or has missing or broken parts, including a damaged cord or plug.
If yours is a gas dryer, it is equipped with an automatic electric ignition and does not have a pilot
light.
DO
N~ ATTEM~ ~
LIGHT WITH A may result from having your hand in the vicinity of the burner when the automatic ignition may turn on.
MA~H.
N~E:
N~
Burns
Dryer-applied fabric softeners or
anti-stitic
conditioners
You may wish to soften your
laundered fabrics or reduce the static electricity in them. We recommend you use either a
fabric softener in the wash cycle, according to the manufacturer’s instructions for try a dryer-added product for which the manufacturer gives written assurance on the package that their product can be safely used in your dryer.
Service or performance problems caused by the use of these products are the responsibility of the manufacturers of those products and
are
not covered under the
warranty of this appliance.
SAVE
thbse
T~SE
products, or
INSTRUCTIONS
4
Page 5
How to operate your dryer
WARNING-To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY INSTRUCTIONS before operating this appliance.
@
K~/WES
L.
bad
Your Dryer Properly
Clean the lint filter each time the
w..,
FLWF
dryer is used. Always be sure the
lint
filter is in place. Don’t use the
dryer without it.
Good sorting for the dryer begins at the washer. Generally, if clothes are sorted right for washing, they’re sorted right for drying. See page 8 for sorting help. (If you do mix various types of fabrics in your
– load, set the controls for the
lighter-weight fabrics and remove when dry. Reset controls for the remaining heavier fabrics. )
A
o
HEAVV DUTY DRVER
wITH
AUTOMATIC ORV CONTROL
Set the Controls
See the Controls Setting Guide on pages 6 and 7.
~
Drying Selections Select the proper heat for your load. Note:
“Fluff
No-Heat” is to be used
only with the TIMED
@
Turn Cycle Selector to desired
cycle setting.
~
Turn START knob to start
dryer.
(Opening the door during operation stops the dryer. To restart, close the
door and turn the START knob.)
~CLES.
#
Polyester Knits &
fiss
Permanent
DO NOT
Garments being dried or
dewrin~ed
REMOVE CLOTHES
PROM~LY—To help prevent wrintiing, remove from the dryer
promptly at the end of the drying cycles.
Q
PLACE ON Permanent Press and Polyester Knit garments look best if placed on hangers after drying.
OVERLOAD—
should tumble freely.
drying tips
HANGERS—
What is the difference between Automatic &
~med
Automatic Drying
When using the AUTOMATIC
SENSI-DRY cycles, the
Dry Control
senses the temperature of the air in the dryer drum. Wet laundry keeps this air cool. When laundry is dry enough (and the drum air warm enough) the heat turns off. When the air cools, the heat turns back on. This off and on cycling may happen a number of times
(depending on the fabric, load size, and Cycle Selector setting). The Cycle Selector advances (when the heat is turns off dryer.
drying?
Automatic
system
of~
until it automatically
continually
5
Timed Drying
When using the TIMED
~CLES,
you select the number of minutes you wish the dryer to run and it turns off at the end of this time period.
TURN THE PAGE
for Controls Setting Guide
Page 6
Controk
bad
Setting Guide for different fabrics and loads
Fabric Care/ Drying Selection
Cycle
Cycle Setting
Cottons & Linens
Permanent Press, Treated Cottons, Blends with Cotton
Synthetics—Polyester, Nylon, Acrylic Knits and Woven Fabrics
Sturdy
Delicate
Silks and Silks and Wools
Rayon and Acetate
Down-filled garments, if machine washing and drying are recommended.
Baby Clothes—Sturdy: Diapers, Nightgowns, Shirts, Pads, Sheets, Receiving Blankets, Coveralls. See Special Instructions.
Baby Clothes—Delicate
Blankets—Wool, Part Wool, Cotton, Electric, Synthetic. See
below
Curtains, Slipcovers, Draperies. DO NW MACHINE DRY FIBERGLASS.
Chenille Bedspreads, Robes. See
below
Rubber-coated Items, Laminated Fabrics, Articles with Plastic Trim.
Bathmats and Rugs
Extra-1arge Items—Queen or King Size Sheets, Blankets or Spreads, Sleeping Bags, Insulated Jackets or Suits, Mattress Covers (Pads), Quilted Bedspreads.
Wools, Blends
under “Extra-large
under “Extra-large
Vinyl,
Plastics and
including
Items~’
Items:’
Cottons
(High)
(Medium)
Permanent Press (Medium)
Knits/Delicates
(Low)
Knits/Delicates
(Low)
Knits/Delicates
(Low) Cottons
(High)
Cottons (High)
Knits/Delicates (Low)
Cottons (High)
Cottons (High)
Cottons (High)
Fhrff
No Heat
Cottons (High)
Permanent Press (Medium)
AUTOMATIC
~;MED
AU~MATIC
~;MED mcLEs
AU~MATIC
AUTOMATIC SENSI-DRY
AU~MATIC SENSI-DRY
AU~MATIC SENSI-DRY Knits.
AUTOMATIC SENSI-DRY
AU~MATIC
or TIMED CYCLES
AU~MATIC SENSI-DRY Knits.
TIMED CYCLES 20 to 25 minutes.
TIMED CYCLES
TIMED CYCLES
TIMED CYCLES
TIMED CYCLES
TIMED CYCLES First setting—20 minutes;
SENSI-DRY
CYCLES
SENSI-DRY
SENSI-DRY
SENSI-DRY
Heavy Fabric or Normal Fabric.
45 minutes for dry; 20 minutes for damp dry for ironing.
Permanent Press.Permanent Press
10 minutes to
that have not been washed.
Permanent Press.
Knits.
Knits.
Normal Fabric.
Heavy Fabric or Normal Fabric.
45 minutes.
For first setting, set at 20 minutes; for second setting, set at 15 minutes.
First setting— 20 minutes; additional settings—5 minutes.
Set for time desired.
First setting—20 minutes; additional settings—5 minutes.
second setting—15 minutes; additional settings—5 minutes.
de-wrin~e
garments
Pillows—Feather and
filld
(if manufacturer recommends they be dried in a dryer). See Special Instructions.
*The terms High, Medium and Low Heat are those
N~E:
The Cycle Selector settings indicated above are to be used as a guide. You may find that best results are obtained for certain of your fabrics
by setting the
Cycle Selector to either side of the recommended settings.
Polyester-
Cottons (High)
TIMED CYCLES
usuallv
found on fabric care labels. For best results,
50 minutes.
follow Your
fabric care labels.
6
Page 7
——
S~cial
Instructions
Do not dry non-colorfast items with whites or light-colored items.
Do not overload dryer; clothes should tumble freely. Remove promptly as soon as dryer stops; place clothes on hangers to minimize wrinkling.
Do not overload dryer; clothes should tumble freely. Remove promptly as soon as dryer stops, place clothes on hangers to minimize wrinkling.
Dry
silks and wools in your dryer
only
if recommended by the garment manufacturer. FO11
OW
instructions carefully.
Tumble drying is mandatory. Down must be thoroughly dried to remove odor and prevent mildewing. Place two large, dry towels in the dryer to improve tumbling and shorten drying time. Two clean, dry tennis shoes added to dryer also help to fluff up the down. Be sure to dry thoroughly.
IMPORTANT. If children’s Check manufacturer’s drying instructions.
—.
sleepwear
is made of Modacrylic,
tumble
dry only on Knits/Delicates (Low). High Heat can damage these fabrics.
See
above
instructions.
Place in dryer with 3 or 4 dry towels which have been heated for 5 minutes. Set timer for 20 to 25 minutes. Do not set control for more than 25 minutes. Do only one blanket at a time. Remove blanket at end of cycle and block blanket back to original shape. Press binding with warm iron. Allow to dry before storing.
Use dry
towels
as buffers. Set timer for 20 minutes. If items are still wet, reset for 15 minutes and check again. Items
still damp. Place slipcovers on furniture immediately. Hang draperies and curtains so that creases
will fall
out. Stop dryer periodically and check
should
be removed while
filter for excess lint. Remove and restart dryer.
Tumble
on FLUFF (No Heat) setting as heat may cause alteration in shape, color and appearance of such articles.
Stop dryer periodically and check
Specialprecautiorrs must be taken for extra-large items. Set dryer for 20mbrutes then check carefilly. Set 15 minutes for second setting, check
again; and 5 minutes for each additional setting. Make sure that article does not
filter for excess lint. Remove and restart dryer.
fill
drum. Many large articles, when wet, have ample room in dryer, but as they dry and fluff up may not have room to tumble. Check carefully every few minutes and if article is still wet or damp and fills dryer, finish drying on have room to tumble, the air flow maybe blocked which be dried in home size dryers.
Check ticking for holes or weak seams where feathers or filling
line.
Do not, under any circumstances operate dryer for longer times without checking. CAUTION: If
DO NOTtumble
d~jackets
could
result in scorching your valuable items. Many large items, like shag rugs, cannot
containing
ffipok.
(See filter cleaning instructions above.)
could
escape. Dry no more than one pillow at a time and set dryer for maximum
large
items do not
time. Stop dryer occasionally and shake pillows to redistribute filling for more even drying. Check pillows at end of drying time. If they are not completely dry, return them to dryer and reset for more drying time. Feather pillows dry very
mildewing.
DO NOTtumble
drypillo~~.v
containing
ffipok.
slowly
and must be dried completely to prevent
Refer to Garment Manufacturers’ Care
hbels
For more information on care labeling, send for “What’s New About CARE LABELS?’ For sale by the Superintendent of Documents, U.S. Government Printing Office, Washington,
7
D.C.
20402.
Page 8
How to sort the clothes
Normally, if you have sorted clothes correctly for washing,
you will also have properly sorted drying loads.
Sort by surface tetiure
Separate
\
from
LINT PRODUCERS—such as terry toweling and chenille—give up lint. LINT such as man-made fibers and
napped fabrics like velveteen and corduroy—attract lint, and must be dried separately.
COLLE~RS—
Sort by fabric
Separate
from
from
Permanent
Press
\
m
from
.
L
Sort by color
Separate
Whites
I
from
Lights
\
m
from
from
L
Delicates
\3
In addition to sorting to reduce lint collection, it is recommended that fabrics of similar construction be dried together whenever possible.
Sort by weight
Separate
—..
Heay”ltems
(such as
towels)
\
m
from
.
Light Items
(such as
curtains)
\
m
For information on tumble drying extra-large items and different fabrics and loads, see pages 6
and
7.
8
Page 9
How to load the
- clothes
Don’t overload your dryer. Crowded loads don’t dry efficiently and clothes may be unnecessarily wrinkled.
Loads should look like this:
Drum with
Cottons & Linens
Drum with
Permanent Press Load
Clean the lint filter before
dryi~
Clean lint filter (see shaded area) by putting your moistened fingers at the corner of filter and wiping in a downward motion all the way across to the other corner.
For additional information on lint filter, see page 13.
every load.
Lint Filter
Ene~y-Saving
Sort clothes by weight so you won’t
~ps
have to run an extra cycle for one or two heavier, slower-drying items.
See page 8.
Do not overload dryer. For
efficient drying, clothes need to tumble freely.
To help prevent ironing, use
Press (Medium) or
Knits/Delicates
Perm
(Low). Remove garments promptly at end of drying cycle and place on hangers.
Dry your clothes in consecutive
loads. Using a “warm” dryer will save energy.
Clean dryer lint filter each time
you dry.
Clean dryer exhaust
ducting
at least once a year. A partially clogged exhaust can lengthen drying time.
—.
9
Page 10
.—
Questiom?
~
-
PROBLEM
DRYER WON’T START
CL~HES ~0
TAKE
LONG ~ DRY
Use This Problem Solver
POSSIBLE CAUSE AND REMEDY
. Dryer unplugged. Make sure power cord is plugged in.
No power to dryer. Check fuses and circuit breakers to make sure dryer is getting
current. Most electric dryers use two.
Controls improperly set. Make sure controls are set and START switch is turned. Opening the door during operation stops the dryer. Tore-start, close the door and turn the START switch.
Dryer door is open. Close door securely—dryer will not run with door open.
Circuit is overloaded. Do not operate other appliances on the same electrical outlet
or circuit while the dryer is operating.
Controls improperly set. Check all controls to make sure they are correctly set for
the load you want to dry. See pages 5-7.
Clogged lint filter. Remove and clean filter before every load. Periodically clean area under lint filter with vacuum cleaner. See page 13.
SHWNKAGE,
GENERAL
Improper
ducting.
Make sure dryer is
ducted
in accordance with Installation
Instructions.
Obstruction in exhaust
ducting.
Make sure
ducting
is clean and free of obstruction; make sure damper in outside wall cap operates easily. If flexible ducting is used, be sure it is not kinked and is properly installed according to Instigation Instructions.
Blown fuses or tripped circuit breakers. Check household fuses or circuit breakers.
Most electric dryers use two. It is possible for one to be blown or tripped and the dryer still tumble without heat.
hproper
Large loads of moisture-holding fabrics, such as beach towels, take a long time to
sorting. Do not mix heavy, hard-to-dry items with lightweight articles.
remove moisture. . Too many items in dryer. Dry only one washer load at a time. Do not combine loads. . Too few items in dryer. If drying only one article, add two more similar articles, even
if dry, to insure proper tumbling.
c
Some
&brics
will shrink whether machine washed and tumble dried or washed by hand and drip dried; others may be safely washed but will shrink in a dryer. Follow Garment Manufacturers’ Care Labels exactly. If in doubt, do not machine wash or tumble dry.
10
Page 11
PROBLEM
SHRINKAGE,
POSSIBLE CAUSE AND REMEDY
Rel~tion
KNITS and
shape
Progressive or delayed shrinkage
gradudly
laundered many times without previous shrinkage. Treat as for
Shrinkage caused by overheating
shaped. When washing, drying or ironing temperatures exceed the temperatures used to shape set, shrinkage may occur. This cannot be corrected, but it can be prevented by washing in cold or warm water; drying on
shrinkage
elongatd
afir
by the manufacturer. When this occurs, garment maybe pressed back into
each wash and dry cycle.
can occur in knit fabrics that have been improperly stretched
is caused when starch or sizing (in some fabrics) is
removed by laundering. Maybe noticed in older garments that have been
Relmtion
Shrinkage above.
occurs in certain knit fabrics that have been
Knits/Delicates (Low).
heat-
W~NKLINGIN
PERMANENT PRESS AND “NO-IRON” ITEMS
Q
Leaving clothes in dryer after tumbling stops. Remove clothes promptly and hang
them immediately.
Q
Too many items in dryer. Dry only one washer load at a time. Do not combine loads.
Q
Too few items in dryer. If drying only one article, add two or more similar articles, even
if dry, to insure proper tumbling.
kproper
loads. Avoid laundering heavy Permanent Press items, such as work clothes, with lighter Permanent Press items, such as shirts or blouses. Do not wash or dry Permanent Press with regular laundry.
Too many clothes in washer. Items must have room to move freely. Permanent Press
loads should always be smaller than regular loads..
Use of incorrect wash and dry cycles. Use Permanent Press Wash Cycle which provides
a cool-down rinse to minimize
writiing.
Also, use Permanent Press (Medium)
.no
more than medium loads.
selection. . Incorrect water level. Use Full Water Fill for medium load; Medium Fill for
small load.
c
Washing repeatedly in too hot water. Wash in cool or
warm water with plenty of detergent.
k
(continued nextpage)
..-
11
.
Page 12
The
Woblem Solver
(continued)
PROBLEM
WWNKLING IN
PERMANENT PRESS AND “NO-IRON”
ITEMS (continual)
POSSBLE
Accumulation of lime scale due
non-phosphate detergent, avoid the use of a high-carbonate detergent.
c
Failure to use fabric softener. Proper
To remove
1.
Retumbleon
2.
Rerinsemddryon
3. If unsuccessful,
4. Iron carefully.
5. Sendtodrycleaners fortressing,
6.
Somewrities mayremainwhich
*N~:
out wrirdded, cotton blends, the cotton portion of the fabric can eventually wear away leaving only the synthetic. Since it’s the cotton portion which is treated for Permanent Press, a loss or decrease of Permanent Press performance
If
you
If you need more help.. call. toll free: The GE Answer
Cen~er@
800.6262000 consumer information service
CAUSE AND
~~DY
to use of carbonate detergents. If you must use a
use
of fabric
sofiner
will minimize wrirdding.
writies:
Permanent Press (Medium) selection.
Permanent Press (Medium) selection.
retumbleonhighheat
follow
good
laundry procedures ud Permanent Press clothes
the
Gnishmay not be good quality. Also, impermanent press synthetic/
for IQ-12 minutes and hang immediately.
cannot be removed?
wdl
result.
still
I
come
Page 13
Care and Cleaning
USER MAINTENANCE INSTRUCTIONS
mod
dryer care
The Drum. Porcelain enamel
drum is rust-resistant and requires
no special care.
The Exterior.
washing compounds. Wipe or dust with damp cloth. Try not to strike the surface with sharp objects.
The Lint Filter.
before every use as described on page 9. Periodically lint filter should be removed and suction hose from vacuum cleaner should be inserted into the opening. See below.
Wipe off any spills or
Wipe lint filter
CAUTIONS:
Before having your electric dryer connected in your new residence, be sure your licensed electrician confirms that the supply voltage matches the voltage specified on the rating plate.
Dryer control panel and finishes
may be damaged by some laundry
pre-treatment soil and stain
remover products if such products are sprayed on or have direct
contact with the dryer.
Apply these away from the dryer. The fabric may then be washed and dried normally. Damage to your dryer caused by not covered by your warranty.
pre-treatment
pre-treatment products is
products
Do not obstruct the flow of combustion and ventilating air.
Dryer Exhaust:
the dryer exhaust once a year.
To store dryer:
time, disconnect power supply and clean lint filter.
Do not store dryer where it exposed to the weather.
Inspect and clean
ducting at least
For short period of
will
be
13
Page 14
Noks
14
Page 15
If You Need Service
To
obtiin
service, see your warranty
on the back page of this book. We’re proud of our service and
want you to be pleased. If for some reason you are not happy with the service you receive, here are three steps to follow for further help.
FIRST, contact the people who serviced your appliance. Explain why you are not pleased. In most cases, this will solve the problem.
NEXT, if you are still not pleased, write all the details-including your phone number—to:
Manager, Consumer Relations
Hotpoint
Appliance Park Louisville, Kentucky 40225
FINALLY, if your problem is still not resolved, write:
Major Appliance Consumer Action Panel
20 North Chicago, Illinois 60606
Wacker
Drive
—.
15
,-
Page 16
YOUR
HOTPOINT
AUTOMATIC
CL~HES
WARRANTY
Save proof of original purchase date such as your sales slip or
cancelled
DRYER
check to establish warranty period.
II
II
WHAT IS COVERED
WHAT IS
N~
COVERED Se~icetriPstoYour
FULL ONE-YEAR WARRANTY
For one year from date of original
purchase, we will provide, free of
charge, parts and service labor
in your home to repair or replace
any
pan
of the
dryer
that fails
because of a manufacturing
defect.
teach you how to use the product.
Read your Use and Care material.
If you then have any questions about operating the product, please contact
Consumer Affairs office at the address below, or call, toll free:
The GE Answer CenteP
800.626.2000 consumer information service
Improper installation.
If you have an installation problem, contact your dealer or installer. You are responsible for providing adequate electrical, gas, exhausting and other connecting facilities.
your dealer or our
hometo
This warranty is extended to the original purchaser and any succeeding owner for products purchased for ordinary home use
48
in the and Washington, warranty is the same except that it is LIMITED because you must pay to ship the product to or for the service technician’s travel
costs to your
All warranty service will be provided by our Factory Service Centers or by our authorized Customer servicers during normal working hours.
Look in the White or Yellow Pages of your telephone directory for
HOTPOINT
GENERAL FACTORY SERVICE or CUSTOMER CARE@ SERVICE.
. Replacement of house fuses or resetting of circuit breakers.
Failure of the product if
for other than its intended purpose or used commercially.
c
Damage to product caused by accident, fire, floods or acts of God.
WARRAN~R
FOR CONSEQUENTIAL DAMAGES.
mainland states, Hawaii
D.C.
In Alaska the
the service shop
home.
Care@
FACTORY SERVICE,
ELECTRIC-HOTPOINT
HOTPOINT
it is used
IS NOT RESPONSIBLE
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion
may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
To know what your legal rights are in your state, consult your local or state consumer affairs office or your state’s Attorney General.
Manager—Consumer
Part No. 113 Pub.
No.
39-9269
12-87
D5497P087
Warrantor: General Electric Company
If further help is needed concerning this warranty, write:
Affaim,
General Electric Company, Appliance Park, Louisville, KY 40225
~lm
DLB6850B
DLL6850B
Loading...