GE DDC4500T1WH, DDC4500SQMWH, DDC4500SPMWH, DDC4500SNMWH, DDC4500SMMWH Owner’s Manual
...
A
WARNING - POTENTIAL FIRE AND SHOCK HAZARD
• Use only rigid metal or flexible metal 4_'diameter ductwork inside the dryer cabinet or for exhausting to
the outside Never use plastic or other combustible ductwork Never use foil or other thin ductwork that
can be easily punctured with a screwdriver or nail
• This appliance must be properly grounded and installed as described in these instructions
Tools you will need
° The dryers must be exhausted to the outside
° Use only metal duct inside dryer cabinet or for exhausting
to outside
WARNING: For your safety the information in
this manual must be followed to minimize the risk
of fire or explosion or to prevent property
damage, personal injury or loss of life.
• Do not store or use gasoline or other
flammable vapors and liquids in the vicinity of
this or any other appliance.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use
any phone in your building.
, Clear the room, building or area of all
occupants.
• Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions
• if you cannot reach your gas supplier call the
fire department
Installation and service must be performed by a
qualified installer, service agency or the gas
supplier.
The American Gas Association requires the following
safety cautions be posted and displayed in a
a. Instructions to be followed in the event the user
Slip joint pliers
Phillips and flat head screwdrivers
prominent location:
smells gas. The information to be posted shall be
obtained by consulting with the local gas supplier.
b. This note:
FOR YOUR SAFETY
DO NOT STORE OR USE GASOLINE OR
OTHER FLAMMABLE VAPORS AND LIQUIDS
tN THE VICINITY OF THIS
OR ANY OTHER APPLIANCE
500A 187P009
aev _ Pub, NO. 31-1724
CAUTION: FOR PERSONAL SAFETY, STACKED UNITS
MUST BE FASTENED SECURELY TO WALL.
REAR VIEW
STEP 1
Attach two chains using Phillips head screws to each end of
upper unit cabinet.
STEP 2
Locate two wall studs behind desired operating _ocation of
stacked units.
NOTE: For wall studs not appropriately spaced, see section
for Alternate Method for installation of Wall Hooks.
STEP 3
Screw two wall hooks into two wall studs (same height as
chain connections on cabinet of upper unit). Both chains
should pul! straight back to wall studs or angle outward.
NEITHER chain should angle inward.
NOTE: The final construction must withstand a pull of
200 Ibs.
STEP4
Connect both dryers to gas supply.
(See GAS CONNECTION iNFOR:MATiON of this instruction.)
STEP 5
Connect both dryers to power supply. (See ELECTRICAL
CONNECTION INFORMATION section of this instruction,)
ATTACH CHAINS HERE
o
! '
STEP 6
Connect both dryers to external exhaust. (See EXHAUST
iNFORMATION section of this instruction.)
STEP 7
Hook both chains from upper unit to appropriate walt hooks
taking up any slack.
STEP 8
Adjust all 4 levelling legs. Dryer must be levelled and rest
firmly on alt 4 levelling legs.
/
Alternate Method for Installation of Wall Hooks
STEP 1
if wall studs are not correctly spaced or centered behind upper unit, it
may be necessary, to attach a horizontal 2" x 4" board to the existing
wall.
STEP 2
Attach wall hooks in approximate position of two chains of upper unit
so each chain pulls straight back to wall.
SIDE VIEW
4 LEVELLING LEGS
WALL STUDS
ffl
WALL HOOKS
NOTE: if wall is concrete or b!ock_ ddll holes and use appropriate wall
anchors. The final construction must withstand a puil of 200 Ibs,
Loading...