GE DDC4400TWH, DDC4400T User Manual
DDC4400T
77
27
27
Gas Dryer
only
Access
Panel
Access
Panel
11-3/4
41-5/8
3-1/2
3/4
1-7/8
2-3/8
GE® 5.4 Cu. Ft. Large Capacity Modular Commercial Electric Dryer
Dimensions and Installation Information (in inches)
Exhaust Options: Shipped with exhaust to the rear.
Electric model offers 3-way venting: left, right, or rear.
Maximum recommended exhaust duct length is 25 feet
of 4" rigid ducting with two 90° elbows and 4" dampered
wall cap.
Requirements:
Electric – 120/240 Volts, 60 Hertz, 120/208* Volts, 60
Hertz, 5600 Watts at 240 Volts, 4400 Watts at 208 Volts.
An individual branch circuit fused for 30-amps is required
for each dryer.
* A special 208 Volt heater, part number WE11X0101 is
available to reduce drying time in 208 Volt installations.
For answers to your Monogram,® GE Profile™ or
GE® appliance questions, visit our website at
ge.com or call GE Answer Center® service,
800.626.2000.
Front View Rear View
Note: Dimensions and specifications shown here are correct at the time this sheet was printed. Before
proceeding with construction or rough-in, check installation instructions that came with your unit.
Specifications, dimensions and design are subject to change without notice.
Note: Wall anchor chain provided for gas models only.
Listed by
Underwriters
Laboratories
Specification Revised 5/09
370404
DDC4400T
Best performance
Domestic
dryer models
Maximum length of 4"
dia. rigid metal duct
Number
of
90°
turns
Exhaust hood type
A
4"
opening
B
2-1/2"
opening
5.7 cu. ft., capacity
electric and
gas dryers
0
1
2
3
4
60 ft.
52 ft.
44 ft.
32 ft.
28 ft.
48 ft.
40 ft.
32 ft.
24 ft.
16 ft.
5.4 cu. ft., capacity
electric and
gas dryers
0
1
2
45 ft.
35 ft.
25 ft.
30 ft.
20 ft.
10 ft.
A
4
B
2-1/2
A
GE® 5.4 Cu. Ft. Large Capacity Modular Commercial Electric Dryer
Dimensions and Installation Information (in inches)
For complete information, see installation instructions packed with your dryer.
Important Note:
GE Kit Number WE14X70 needed when converting rear exhaust to bottom or side.
(On large capacity models.)
Ducting Materials:
For best performance, this dryer should be vented with 4" diameter all rigid metal
exhaust duct. If rigid metal duct cannot be used, then UL-listed flexible metal (semirigid) ducting can be used (Kit WX08X10077). In special installations, it may be
necessary to connect the dryer to the house vent using a flexible metal (foil-type)
duct. A UL-listed flexible metal (foil-type) duct may be used ONLY in installations
where rigid metal or flexible metal (semi-rigid) ducting cannot be used AND where a
4” diameter can be maintained throughout the entire length of the transition duct.
Please see installation instruction packed with your dryer for complete instructions
when using flexible metal (foil type) ducting.
Exhaust Length Calculation
1. Determine the number of 90° turns needed for your installation. If you exhaust to
the side or bottom of dryer, add one turn.
2. The maximum length of 4' rigid (aluminum or galvanized) duct which can be
tolerated is shown in the table.
A turn of 45° or less may be ignored. Two 45° turns within the duct length should be
treated as a 90° elbow. A turn over 45° should be treated as a 90° elbow.
Dryers must be exhausted to the outside.
Caution: For personal safety do not terminate exhaust into a chimney, under any
enclosed house floor (crawl space), or into an attic, since the accumulated lint could
create a fire hazard or moisture could cause damage. Never terminate the exhaust
into a common duct or plenum with a kitchen exhaust, since the combination of lint
and grease could create a fire hazard.
Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts,
bird nesting, etc. The wall cap must also be located at least 12" above the ground or
any other obstruction with the opening pointed down.
For answers to your Monogram,
GE® appliance questions, visit our website at
ge.com or call GE Answer Center® service,
800.626.2000.
®
GE Profile™ or
Special Installation Requirements
Alcove or Closet Installation:
• If your dryer is approved for installation in an alcove or closet, it will be stated on a label on the
dryer back.
• The dryer MUST be exhausted to the outside.
• Minimum clearances between dryer cabinet and adjacent walls or other surfaces are:
0" either side
3" front and rear
• Minimum vertical space from floor to overhead cabinets, ceilings, etc. is 52".
• Closet doors must be louvered or otherwise ventilated and must contain a minimum of 60 sq. in.
of open area equally distributed.
If this closet contains both a washer and a dryer, doors must contain a minimum of 120 sq. in. of
open area equally distributed.
• The closet should be vented to the outdoors to prevent gas pocketing in case of a gas leak in the
supply line.
• No other fuel-burning appliance shall be installed in the same closet with the dryer.
Bathroom or Bedroom Installation:
• The dryer MUST be exhausted to the outdoors.
• The installation must conform with the local codes, or in the absence of local codes, with the
Natioinal Electric Code and National Fuel Gas Code, ANSI Z223 for gas dryers.
Minimum Clearances other than Alcove or Closet Installation:
• Minimum clearances to combustible surfaces
0" both sides
3" rear
Dryer Exhausting Information – Use Metal Duct Only
Listed by
Underwriters
Laboratories
Specification Revised 5/09
370404
Loading...