GE EGD5600G0WW, EGD4600G1WW, EGD4600G0WW, EED5600G1WW, EED5600G0WW Owner’s Manual

...

ge.com

Safety Instructions ........ 2-4

Operating Instructions

Control Panel ................. S,6

Control Settings ................. 7

Features ....................... 8

Loading and Using

the Drger ................... 10-11

Reversing the Door .............. 9

Venting the Drger .............. 11

Troubleshooting Tips ... 12, 13

Consumer Support

Consumer Support ..... Back Cover

Warrantg ..................... 15

DBLR333 DBSR463 DBXR463

DHDSR46

DJXR433 DLLLR23 DLLSR34 DLLSR40 DLSR483

DQSR483

DRSR483 DRSR495

DVLR223 DWSR463 DWSR483 DWXR463 DWXR483

DX2300

DX4500 EED4600 EED5600

EGD4600 EGD5600

Write the model and serial numbers here:

Model # Serial #

Youcan find them on a label on the front of the drger behind the

dooE

175D1807P586 49-90318 12-06 JR

IMPORTANT SAFETY INFORMATION. READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or

death.

• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

• Installation end service must be performed by o qualified installer,

service agency or the gas supplier.

WHAT TO DO IF YOU SMELL GAS:

[] Do not try to light a match, or

cigarette, or turn on any gas or

electrical appliance.

[] Do not touch any electrical switch;

do not use any phone in your building.

[] Clear the room, building or area of all

occupants.

California Safe Drinking Water and Toxic Enforcement Act

This act requiresthe governor of Californiato publish alist of substances known to the state to cause cancer,

birth defects or other reproductive harm and requires businessesto warn customers of potential exposureto such substances.

Gasappliances cancause minor exposureto four ofthesesubstances,namely benzene,carbon monoxide, formaldehyde and soot,causedprimarily by the incomplete combustion of natural gas or LPfuels.

Properly adjusted dryers will minimize incomplete combustion. Exposureto thesesubstances can be minimized further by properly venting the dryer to the outdoors.

[] Immediately call your gas supplier

from a neighbor's phone. Follow the gas supplier's instructions carefully.

[] If you cannot reach your gas supplier,

call the fire department.

PROPERINSTALLATION

This dryer must be properlg installed and located in accordance with the Installation Instructions

before it is used. If you did not receive an Installation Instructions sheet, you can receive one by visiting ge.com or bg calling 800.GE.CARES (800.432.2737).

[] Properlyground dryer to conform with all

[] Installor store where it will not be exposed to

[] Connectto a properly rated, protected and sized

[] Removeall sharp packing items and disposeof

governing codesand ordinances. Followdetails in Installation Instructions.

temperatures below freezingor exposed to the weather,which could causepermanent damage

and invalidatethe warranty.

power supply circuit to avoid electrical overload.

all shipping materials properly.

Exhaust/Ducting

]Gas dryers MUST be exhausted to the outside. ]Use only rigid metal 4" diameter ductwork inside

the dryer cabinet. Use only rigid metal or flexible metal 4" diameter ductwork for exhausting to the

outside. USE OF PLASTIC OR OTHER

COMBUSTIBLEDUCTWORKCANCAUSE A FIRE.PUNCTUREDDUCTWORKCANCAUSEA FIREIFITCOLLAPSESORBECOMESOTHERWISE

RESTRICTEDIN USEORDURINGINSTALLATION.

Forcomplete details,follow the Installation Instructions.

WARNING!

YOUR LAUNDRY AREA

ge.com

• Keepthe area underneath and around your appliances free of combustible materials,

(lint, paper,rags,etc.),gasoline,chemicals and other flammable vapors and liquids.

• Keepthefloor around your appliances clean and dry to reducethe possibilityof slipping.

• Closesupervisionisnecessary ifthis appliance is used by or near children. Do not allow children to

play on,with or inside this or any other appliance.

WHEN USING YOUR DRYER

• Neverreach into the dryer while the drum is

moving. Beforeloading, unloading or adding clothes,wait until the drum has completely

stopped.

• Cleanthe lint filter beforeeach load to prevent lint

accumulation inside the dryer or in the room. DO

NOTOPERATETHEDRYERWITHOUTTHELINT FILTERIN PLACE.

• Do not wash or dry articles that have been

cleaned in,washed in,soakedin or spotted with combustible or explosivesubstances(such as

wax, oil,paint, gasoline,degreasers,dry-cleaning solvents,kerosene,etc.).Thesesubstances give

off vapors that may ignite orexplode. Donot add these substances to the wash water Do not use

or placethese substancesaround your washer or dryer during operation.

• Do not place items exposed to cooking oilsin

your dryer Items contaminated with cooking oils may contribute to a chemical reaction that could

cause a clothesload to catch fire.

• Any article onwhich you have used acleaning

solvent or that contains flammable materials (suchas cleaning cloths,mops,towels used in

beauty salons, restaurants or barber shops,etc.) must not be placedin ornear the dryer until

solvents or flammable materials have been removed.Thereare many highly flammable items

used in homes suchasacetone, denatured alcohol, gasoline,kerosene,somehousehold cleaners,some spot removers,turpentines, waxes, wax removers

and products containing petroleum distillates.

• Keepall laundry aids(suchas detergents, bleaches,etc.)out of the reach of children,

preferably in a locked cabinet. Observeall warnings on container labelsto avoid injury.

• Neverclimb on or stand onthe dryer top.

• Thelaundry processcan reduce the flame

retardancy offabrics. To avoid sucha result, carefully follow the garment manufacturer's

care instructions.

• Do not dry articles containing rubber, plastic

or similarmaterials such aspadded bras,tennis shoes,galoshes, bath mats, rugs, bibs,baby pants,

plastic bags, pillows,etc.that may melt or bum. Somerubber materials,when heated, can under

certain circumstances produce fire by spontaneous combustion.

• Do not store plastic, paper orclothing that may

burn or melt on top ofthe dryer during operation.

• Garments labeled Dry Away from Heotor DoNot

TumbleDry (suchas lifejackets containing Kapok) must not be put in your dryeE

• Do not dry fiberglass articles inyour dryer

Skinirritation could result from the remaining particles that may bepicked up by clothing

during subsequent dryer uses.

• Tominimizethe possibility of electric shock, unplug

this appliance from the power supply or disconnect the dryer at the household distribution panel by

removing the fuse or switching offthe circuit breaker before attempting any maintenance or

cleaning (exceptthe removal and cleaning ofthe lint filter).NOTE:Turningthe CycleSelectorknob

to an off positionor pressingPAUSEdoesNOT disconnect the appliance from the power supply.

IMPORTANT SAFETY INFORMATION. READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

WHEN USING YOUR DRYER(cont.)

• Neverattempt to operate this appliance if it is damaged, malfunctioning, partially disassembled,

or has missing or brokenparts, including a damaged cord or plug.

• Theinterior of the machine and the exhaust duct connection insidethe dryer should becleaned at

leastonce a year by a qualified technician. Seethe

Loading and Usingthe Drblersection.

• Ifyours is a gas dryer,it isequipped with an automatic electric ignition and does not have

a pilot light. DO NOTATTEMPTTOLIGHTWITH A MATCH.Burnsmay result from having your hand

in the vicinity ofthe burner when the automatic ignition turns on.

WHEN NOT USING YOUR DRYER

• Graspthe plug firmly when disconnecting this appliance to avoid damage to the cord while

pulling.Place the cord away from traffic areas

soit will not bestepped on,tripped over or subjected to damage.

• Donot attempt to repair or replaceany part of this appliance orattempt any servicingunless

specificallyrecommended in this Owner's Manual or inpublisheduser-repairinstructionsthat you

understand and have the skillsto carry out.

• Beforediscarding a dryer, or removing it from

• Do not tamper with controls.

Youmay wish to soften your laundered fabrics or reducethe static electricity in them by using

a dryer-applied fabric softener or an anti-static conditioneEWe recommend you use either a

fabric softener in the wash cycle, according to the manufacturer's instructions for those products,

or try a dryer-added product for which the manufacturer giveswritten assurance on the

package that their product can be safely used in gour dryeEServiceor performance problems

caused bg useof these products are the responsibility of the manufacturers of those

products and are not covered under the warranty to this appliance.

service,remove the dryer door to prevent children from hiding inside.

\l|j

..,.__ READANDFOLLOWTHISSAFETYINFORMATIONCAREFULLY.

/_\'_ SAVE THESE INSTRUCTIONS

About the drger control panel, ge.com

You can locate _qourmodel number on the label on the front of the dryer behind the door, Throughout this manual, features and appearance may vary from _jour model.

Model DVLR223

LESSDRY 70

80 MIN

START OPilMOMDRY [TIMED DRY 1

(_ _

IB m

Models DX2300 and DLLLR23

START

Models DBSR463, DBXR463, DHDSR46 and DX4500

START FABRIC CARE

START

_TTONS _S¥ CARt

_E_H_ ME_H_T

SIGNAL _z;

raED_M "•

MORE DRY

COTTONS]

AUTOMATIC REGULARHEAT

LESSOOY

"'Optional features

(on some models) .........

AUTO.TIC

MEDIUMHEAT

80 MIN

OEWRINKLE20

Ipz

No H_ low H_

irt B El

Model DBLR333

START

Push to _$#_t

FABRIC CARE

LESSDRY

MEDIUM

MOSEDRY

LESSDOY

(2)

30 40 59

m. Irl El

NOTE: Drging times will varg according to the tgpe of heat used (Electric, Natural or LPgas), size of load,

tgpes of fabrics, wetness of clothes and condition of exhaust ducts.

About the dryer control panel.

You can locate gour model number on the label on the front of the dryer behind the door. Throughout this manual, features and

appearance mag varg from gour model. Models DJXR433, DWSR483, DWXR483 and DLSR483

START FARRJC CARE WRINKLE CARE SIGNAL

Model DLLSR34

START

FABRIC CARE

3 Heot 5etting_

MEDIUM

. B El

Model DRSR495

SIGNAL FABRIC CARE WRINKLE CARE

COTTONS EASYCASE

oN .EG.EAT HED.EAT

FL CATES

NOHEAT LOWHEAT

DAMPD_¥3O

,By

LESSo_Y

_ [EASY CARE]

C_E

;; WR/NKLEFREE

) DEL CATES

}} LESSDRY

AUTOMATIC

DELICATES

,n El IB

Models DQSR483, DRSR483, DWSR463, DWXR463, DLLSR40, EED5600, EED4600, EGD5600 and EGD4600

SIGNAL

MEDIUM

FABRIC CARE

4 Heat Settings

COTTONS EASY CARE f_EGHEAT HED BEAT

WRINKLE CARE

Extended CootAir Tu_ble _ _tE _

OF_ oN o_H_.v

A_OMAr_C L_So.'_

START

NOHEAT LOWHEAT

I!1 El 0

Optional features .... -_2,w.,.._

(on some models) o._..._

START

NOTE: Drying times will vary according to the tgpe of heat used (Electric, Natural or LPgas), size of load, tgpes of fabrics, wetness of clothes and condition of exhaust ducts.

About the control settings.

IMPORTANT: Clean the lint filter each time gou use the drger.

ge.com

H Fabric Care/Temperature (onsome models)

REGULARForregular to heavycottons.

or COTTONS

REG.HEAT

MEDIUM, For synthetics, blends, delicates and items labeled permanent press.

EASYCARE

MED. HEAT,

EASYCARE

or PERMA PRESS

MED. HEAT

DELICATES On some models. For delicates, synthetics and items labeled tumble dry Io_z LOW HEAT

FLUFF For fluffing items without heat. Usethe TIMED DRY cycle.

NO HEAT

Automatic cycles automatically determine fabric dryness.SelectLESSDRYif you want your clothes slightly damp at the endof the drying cycle.Select MOREDRYif you want them to feel drie[ Timed

cycles runfor a selectedtime.

_ Drying Cycles

COTTONS For cottons and most linens. For most loads, select OPTIMUMDRY (onsome models) or

select the Preferred Regular Setting marked with an *.

EASYCARE/ For wrinkle-free, permanent press and delicate items, and knits.

PERMANENT

PRESS

DEUCATES

TIMED DRY

DAMP DRY

DEWRINKLE

Fordelicate items,special-care fabrics and knits. Setthe CgcleSelector at the desireddrying time.

For leavingitems partially damp. Forremoving wrinkles from items that are clean and dry or that are very lightly damp.

QUICK FLUFF

Forfreshening or fluffing up alreadg dry clothing,fabrics, linensand pillows.Usewith

FLUFFNO HEAT.Provides10 minutes of no heat tumbling.

Start-Close the dryer doo[ SelectSTART.Openingthe door during operation will stop the drye[

To restart the dryer,closethe door and selectSTARTto complete the cycle.

Color Logic (onsome models)

Select the correct FABRICCARE setting.

Hatch the particular color below the words

with the same color on the Cycle Dial.

Example: Drying a load of clothing labeled

permanent press.

F] Choosethe FABRICCAREsetting--for

this load it would be the EASYCAREMED. HEAT(whichisa particularcolor).

r-_-]Turn the Cycle Dial to the areathat has

the same color asthe FABRICCARE setting gou have chosen-for thisload it

would bethe EASYCAREAUTOMATIQ

About the dryer features.

WRINKLE CARE

Wrinkle Care Option (onsomemodels)

Usethis option to minimizethe wrinkles

in clothes. It provides approximately

15 minutes of no-heat tumbling after

the clothes are dry. Thisoption can only be used with the

COTTONSand EASVCAREcgcles,

Cgcle Signal Option (onsomemodels)

Thissignalwill sound just beforethe end of the cgcle to remind you to remove the

clothes.On some models,the signal sound

levelcannot be adjusted, IfUouselectedthe WRINKLECAREoption,

the signal will sound at the end of the drying time and will sound severaltimes during the

WRINKLECAREcurie.Thiswill remind gou

that it istime to remove the clothes.

If Uou are using the CYCLESIGNALknob and you selectthe WRINKLECAREoption,

a signalwill sound at the end of the drying time and severaltimes during the WRINKLE

CAREcycle.Thiswill remind Uouthat it istime to remove the clothes.

If WRINKLE CAREis not on, the dryer will stop once the timer reaches the WRINKLE CARE

mark on the cycle dial.

NOTE:

• Removegarments promptly at the sound of the signal. Placeclothes on hangers so

wrinkles won't set in.

• Usethe Cycle Signal especially when drying fabrics like polyester knits and

permanent press. Thesefabrics should be removed so wrinkles won't set in.

Automatic Cycle Signal tonsomemodels)

Atthe end of each cgcle,there is A reminder signalwill sound periodicallu approximately 15 minutes of no-heat during thistime to remind you to remove

tumbling after the laundry is dry. the laundry.

Drum Lamp (on somemodels)

Beforereplacing the light bulb,be sure to unplug the dryer power cord or disconnect

the dryer at the household distribution panel

bg removing the fuse or switching offthe circuit breake_Reachabove dryer opening from insidethe drum. Removethe bulband

replacewith the same sizebulb.

Drying Rack (onsomemodels)

A handg drying rack mag be usedfor drying delicate items such aswashable sweaters.

Hook the rack over the lint filter so the rack extends into the dryer drum.

NOTE:

• The drying rock must be used with the TIMED CYCLE.

• Do not use this drying rack when there are other clothes in the dryer.

Stainless Steel Drum (onsomemodels)

The stainlesssteel usedto make the dryer

drum provides the highest reliabilitg available in a GEdrye_ If the dryer drum shouldbe

scratched ordented during normal use,

the drum will not rust or corrode. These

surface blemisheswill not affect the function or durabilitg of the drum.

About reversing the door. ge.com

Reversing the Door Toolsneeded:

[] 5tondord #2 [] Tope-tipped

Phillipsscrewdriver putty knife

[_ Openthe door and remove the filler plugsopposite the hinges.With the door completel9

open,remove the bottom screw from each hingeon the dryer face, Insertthese screws about half wau into the TOPholes,for each hinge, on the opposite side(where you

removed the filler plugs).Applufirm pressureto get the screw started in new holes.

[_] Loosentop screw from each hinge on the dryer face half wag, With one handholding the

top of the door and the other hand holding the bottom, remove the door from the druer bg liftingit UP and OUT.

[_] Rotatethe door 180°.Insert it on the opposite sideof the opening bg moving the door

IN and DOWN until the top hingeand the bottom hinge are resting on the top screws inserted in step 1.

I_] Removethe remaining screwsfrom the sideof the opening from which the door

was removed. With these screws,secure each hinge at the bottom. Tighten the two top screwsof each hinge.Reinsertthe plastic plugson the sidefrom which

the door was removed,

Loadingand usingthe dryer.

Always follow the fabric manufacturer's care label when laundering.

Sorting and Loading Hints

As a general rule, if clothes are sorted properly for the washer, theg are sorted properly for the drgeE

Do not add fabric softener sheets once the load has become warm. They may cause fabric softener stains.

Bounce ®Fabric Conditioner Dryer Sheets hove been approved for use in all GEDryers when used in

accordance with the manufacturer's instructions.

Careand Cleaning of the Dryer

The Exterior: Wipe or dust any spills or washing

compounds with a damp cloth. Dryer control panel and finishes may be damaged by some laundry pretreatment soil and stain remover products.

Apply these products awag from the dryeE The fabric may then be washed and dried normally. Damage to

your dryer caused bg these products is not covered by gour warranty.

The Lint Filter: Clean the lint filter before each use. Moisten your fingers and reach into the filter opening. Run your fingers across the filten Have a qualified technician vacuum the lint from the dryer once a gear

Do not overload.Thiswastes energy and causes wrinkling.

Do not dry the following items: fiberglassitems, woolens,rubber-coated items, plastics,items with

plastictrim and foam-filled items.

Stainless Steel: To clean stainless steel surfaces,

use a damp cloth with a mild, non-abrasive cleaner suitable for stainless steel surfaces. Removethe

cleaner residue, and then dry with a clean cloth. TheExhaust Duct: Inspectand clean the exhaust

ducting at leastonce a gearto prevent clogging. Apartially clogged exhaust can lengthen the

drying time.

Follow these steps:

M Turn offelectrical supply bg disconnecting the

plug from the wall socket.

F_ Disconnect the duct from the dryer F_ Vacuum the ductwith the hose attachment and

reconnect the duct.

TheExhaust Hood:Checkfrom the outsidethat the flaps of the hood move freely when operating. Hake

surethat there isnot wildlife (birds,insects,etc.)nesting insidethe duct or hood.

ge.com

Venting the Dryer

Forthe best drging performance, the dryer needsto be properlg vented. Thedryer will usemore energy and run longerif it is not vented to the below specifications. Carefully follow the details on Exhausting in

the Installation Instructions.

[] Useonlg rigidmetal 4" diameter ductwork insidethe

drger cabinet. Useonlg rigidmetal or flexible metal4" diameter ductwork for exhausting to the outside.

[] Donot useplastic or other combustible ductwork. [] Usethe shortest length possible.

[] Donot crush orcollapse. [] Avoid restingthe duct on sharp objects.

[] Venting must conform to local building codes.

Correct Venting

Incorrect Venting

(

Before you call for service...

Troubleshooting Tips Save time and money! Review the charts on the following pages, or visit

Problem Possible Causes What To Do Dryer doesn't start Dryer is unplugged • Hakesure the dryer plug is pushedcompletely into

Dryer doesn't heat Fuse isblown/circuit breaker is • Checkthe house fuse/circuit breaker box and replace

Dryer shakes or Someshaking/noiseisnormal. • Hove dryer to an evenfloor space,or adjust levelinglegs makes noise Dryer may be sittingunevenly as necessary until even.

Greasy spots on clothes Improper use of fabric softener • Followdirections on fabric softener package.

Be.com. You may not need to call for service.

the outlet,

Fuse is blown/circuit breaker • Checkthe house fuse/circuit breaker box and replace istripped fuse or reset breakeENOTE:Host electric dryers use

2fuses/breakers.

tripped; the dryer may tumble both fuses or reset both breakers.Yourdryer may tumble

but not heat if only one fuse isblown or onebreaker tripped. Gasservice is off • Hakesure gas shutoff at dryer and main shutoff are

fully open.

Drying dirty items with • Useyour dryer to dry only clean items. Dirty items can clean ones stain clean items andthe dryeE

Clothes were not • Sometimes stains which cannot be seen when the completely clean clothes are wet oppeorafter drying. Useproper washing

procedures before drying.

Lint on clothes Lint filter isfull • Clean lint screenbefore each load.

Improper sorting • Sort lint producers (likechenille)from lint collectors

(likecorduroy).

Static electricity can attract lint • Seesuggestions in this sectionunder STATIC. Overloading • Separate largeloads into smallerones.

Paper,tissue, etc. left in pockets • Empty all pockets before launderingclothes.

Static occurs No fabric softenerwas used • Try a fabric softeneE

• Bounce®FabricConditioner Dryer Sheetshave been approved for usein all GEDryers when used in

accordance with the manufacturer's instructions,

Overdrging • Try a fabric softener:

• Adjust setting to LESSDRYorDAMPDRY

Synthetics, permanent press • Try a fabric softener: and blendscan cause static

Inconsistent Type of heat • Automatic drying times will vary according to the type drying times of heat used(electric,natural orLPgas),sizeof load,

types of fabrics,wetness of clothes and condition of exhaust ducts.

ge.eom

Problem Possible Causes Clothes take too long Improper sorting

to dry

Large loads of heavg fabrics {likebeach towels)

Controls improperlg set Lint filter is full

Improper or obstructed ducting

Blown fuses or tripped . Replace fuses or reset circuit breakers. Since most dryers circuit breaker use 2 fuses/breakers, make sure both are operating.

Overloading/combining loads . Do not put more than one washer load in the dryer

Underloading . If you are drying only one or two items, add a few items

What To Do

, Separate heavy items from lightweight items (generally,

a well-sorted washer load isa well-sorted dryer load),

, Large,heavy fabrics contain more moisture and take

longer to dry. Separatelarge,heavy fabrics into smaller loadsto speeddrying time.

, Match control settings to the load you are drying.

Cleanlintfilter before every load. Checkinstallation instructions for proper

ductingiventing. Makesure ducting isclean, free of kinksand

unobstructed. Checkto see if outside wall damper operates easily.

Checkthe Installation Instructions to make surethe dryer venting iscorrect.

at a time.

to ensure proper tumbling.

Clothes are wrinkled Overdrying , Select a shorter drying time.

, Remove items while they still hold a slight amount of

moisture. Select a LESSDRY or DAMP DRY setting.

Letting items sit in dryer , Remove items when cgcle ends and fold or hang after cycle ends immediately.

Overloading , Separate large loads into smaller ones.

Clothes shrink Some fabrics will naturally shrink , To avoid shrinkage, follow garment care labels exactly.

when washed. Others can be . Some items may be pressed back into shape after drying. safely washed, but will shrink

in the dryer . If you are concerned about shrinkage in a particular

item, do not machine wash or tumble dry it.

Notes.

GEDryer Warranty.

All warrant;] service provided by our Factor;] Service Centers,

or an authorized Customer Card_ technician. To schedule service, on-line, 24 hours a day, visit us at ge.com, or call 800.GE.CARES

(800.432.2737). Please have serial number and model number available when calling for service.

For The Period Oh GE Will Replace:

One Year From the date of the

oniginolpurchase

What GE Will Not Cover:

[] Service trips to gout home to teach gou how to []

usethe product.

[] Improper installation, deliverg or maintenance. [] [] Failure of the product ifit is abused, misused, or

used for other than the intended purpose or used []

commerciallg.

[] Replacement of the light bulb. [] [] Products which are not defective or broken, or which

are working as described in the Owner's Manual. []

Any part of the drger which failsdue to adefect in materials or workmanship. During this limited one-year warranty, GEwill also provide,free of charge, all labor and related service costs

to replacethe defective part.

Staple your receipt here.

Proof of the original pumhase

dote is needed to obtain

support under the warranty.

Replacement of house fuses or resetting of circuit breakers.

Damage to the product caused bg accident, fire, floods

or acts of God. Incidental or consequential damage caused bg possible

defects with this appliance. Defects or damage due to operation in freezing

temperatures. Damage caused after deliverg.

[] Product not accessibleto provide required service.

EXCLUSION OF IMPLIED WARRANTIES--Your sole and exclusive remedy is product repair as provided in this Limited Warranty. Any implied warranties, including the implied warranties of merchantability or fitness for a particular

purpose, are limited to one year or the shortest period allowed by law.

This warranty is extended to the original pumhoser and any succeeding owner for products purchased for home use within the USA. If the product is located in an area where service by a GE Authorized Servicer is not

available, you may be responsible for a trip charge or you may be required to bring the product to on Authorized GE Service location. In Alaska, the warranty excludes the cost of shipping or service calls to your home.

Some states do not allow the exclusion or limitation of incidentaf or consequential damages. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. To know

what _]our legal rights are, consult your local or state consumer- affairs office or _jour state's Attorney] General.

Warrantor: General Electric Company. Louisville, KV 40225

+ 33 hidden pages