Do not expose the camera battery pack or other accessories to
rain or humidity to prevent re hazard or electric shock.
For customers in the U.S.A.
Tested To Comply With FCC Standards
FOR HOME OR OFFICE USE
FCC Statement
This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including
interference that may cause undesired operation.
For customers in Europe
"CE" mark indicates that this product complies
with the European requirements for safety, health,
environment and customer protection. "CE" marked cameras
are intended for sales in Europe.
This symbol [crossed-out wheeled bin WEEE Annex IV]
indicates separate collection of waste electrical and
electronic equipment in the European countries. Please
do not throw the equipment into the domestic refuse. Please
use the return and collection systems available in your country
for the disposal of this product.
Declaration of Conformity
Model Name: C1033 / C1233
Trade Name: GE
Responsible Party: General Imaging Co.
Address: 1411 W. 190th Street, Suite 550, Gardena,
Customer Service Telephone Number:
(Outside U.S. & Canada: +1-310-755-6857)
Conforms to the following Standards:
EMC: EN 55022:1998/A1:2000/A2:2003 Class B
EN 55024:1998/A1:2001/A2:2003
EN 61000-3-2:2000/A1:2001
EN 61000-3-3:1995/A1:2001
following the provision of the EMC Directive (89/336/
EEC,2004/108/EEC)
CA 90248, U.S.A.
+1-800-730-6597
i
SAFETY PRECAUTIONS
Camera notes:
Do not store or use the camera in the following types of
locations:
• In the rain, very humid and dusty places.
• In a place where the camera can be exposed directly to the
sunlight or subject to high temperature, e.g. Inside a closed
car in summer.
• In a place where the camera is subject to a high magnetic
eld, e.g. near motors, transformers or magnets.
Do not place the camera on a wet surface or places where
dripping water or sand may come in contact with the camera,
which may cause irrepairable faults.
If the camera will not be used for a long period of time, we
suggest you remove the battery and the memory card from
the camera and keep them in dry environment.
If you carry the camera suddenly from a cold location to a
warm place, moisture may condense inside the camera. We
suggest you wait for a while before turing on the camera.
No compensation for loss of recordings. Loss of recordings
cannot be compensated for if a malfunction of your camera
or recording media, etc, makes the playback of recordings not
possible.
Battery notes:
Incorrect use of the batteries may cause them to leak, become
hot, ignite or burst. Always observe the precautions given below.
• Do not expose the batteries to water, and take particular
care to keep the terminals dry.
• Do not heat the batteries or throw them into a re.
• Do not attempt to deform, disassemble or modify the
batteries.
Keep the batteries out of reach of babies and small children.
In cold locations, battery performance deteriorates and the
time for which they can be used shortens markedly.
Memory card notes:
When using a new memory card, or a memory card has been
initialized by a PC, be sure to format the card with your digital
camera before using it.
To edit image data, copy the image data to the PC’s hard disk
rst.
Do not change or delete the folder names or le names in the
memory card from your PC, as this may make it impossible
to recognize or misinterpret the original folder or le in your
camera.
The photos taken by this camera are stored in the auto-
generated folder in SD card. Please do not store photos that
are not taken by this model of camera, as this may make it
impossible to recognize the picture when the camera is in
playback mode. Please do not expose the camera to harsh
environments such as moisture or extreme temperatures,
which may shorten the life of your camera or damage the
batteries.
iiii1
BEFORE YOU START
Preface
Thank you for purchasing this GE digital camera. Please read
this manual carefully and keep it in a safe place for future
reference.
No part of this publication may be reproduced, transmitted,
transcribed, stored in a retrieval system, or translated into
any language or computer language, in any form, by any
means, without the prior written permission of General Imaging Company.
Trademarks
All trademarks mentioned in this manual are used for identi-
cation purposes only and are properties of their respective
owners.
Safety information
Please read the following important information carefully
before using the product.
• Do not take apart or attempt to service the camera your-
self.
• Do not drop or knock the camera. Improper handling may
damage the product.
• Turn o the camera before inserting or removing the bat
tery and memory card.
• Use only the type of battery that come with the camera.
Using other types of batteries may damage the camera
and invalidate the warranty.
• Do not touch the camera lens.
•
Please not expose the camera to harsh environments such
as moisture, or extreme temperatures, which may shorten
the life of your camera or damage the batteries.
• Do not use or store the camera in dusty, dirty, or sandy
areas, as its components may be damaged.
-
• Do not expose the lens to direct sunlight for extended
periods.
• Download all pictures and remove the batteries from
the camera if you are going to store the camera for long
periods of time.
• Do not use abrasive cleansers, alcohol-based, or solventbased cleaners to clean the camera. To clean, wipe the
camera with a slightly damp soft cloth.
About this manual
This manual provides you with instructions on how to use your
GE digital camera. Every eort has been made to ensure that
the contents of this manual are accurate, however General
Imaging Company reserves the right to make changes without
notice.
Symbols used in this manual
Throughout this manual, the following symbols are used to
help you locate information quickly and easily:
Indicates the useful information to know.
Indicates precautions to be taken while operating the
camera.
Your package should contain the camera model you purchased along with the following items. If anything is missing or appears to
be damaged, please contact your vendor.
Insert the Battery and SD/SDHC Card (Not included)
1. Open the battery compartment.
2.Insert the enclosed batteries into the battery slot in the
correct direction.
1011
card slot as shown.
4. Close the battery compartment.3. Insert an SD/SDHC card (not included) into the memory
Optional SD/SDHC cards are not included. The use
of 64MB to16 GB memory cards from recognized
manufacturers such as SanDisk, Panasonic and Toshiba
is recommended for reliable data storage.
To remove the SD/SDHC card, open the battery
compartment and gently push the card to release it.
Pull the card out carefully.
Turning On and O
Press the Power button to turn the camera on. To turn o the
camera, press the Power button again.
Power Button
When the camera is turned on, it will be at the same shooting
mode based on the last use. You can press the Mode button to
select a dierent one after it is on. When using the camera for
the rst-time, the language setting page will appear. Please
see page 14 or the Quick Start Guide in the package for details.
12131213
Using the Mode Button
The GE camera provides a convenient Mode Button that allows you to switch between dierent modes with ease. Press Left/Right
button to choose the mode, press to select. All the available modes are listed as follows:
Mode NameIconDescription
Auto modeSwitch to take still pictures in automatic mode.
Panorama mode
Stabilization mode
Scene modeSwitch to take still pictures in 12 dierent scene types by your choice.
Movie modeSwitch to record videos.
PortraitSwitch to take portrait pictures under normal condition.
Switch to capture a sequence of shots and stitch them together into a panoramic photo.
Switch to take still pictures by reducing the blurs caused by hand shake, under low luminance, or
slow shutter speed.
Setting Date/Time and Language
To set the language, date, and time, go to the following setup
options in the Setup menu.
• Date / Time
• Language
To access the Setup menu, do the following:
1. Press
Power to turn the camera on.
2. Press the button, switch among the setting menus by
using the Left/Right button to select the corresponding
basic setting menu.
3. Press the button to conrm the setting.
Setting the Date and Time
1. Use the
2. Press the
3. Press the
Up/Down button to select Date/Time. Then
press the Right button to enter the setting.
Left/Right to highlight each field and use the
Up/Down to adjust the value.
button to conrm the setting.
1415
Setting the Language
1. Use the
2. Use the Left/Right buttons to select the desired language.
3. Press the
Up/Down button to go to the Language. Then
press the Right button to enter the setting.
button to conrm the setting.
The Date/Time and Language setup will automatically
appear when the camera is turned on the rst time.
About the LCD Screen
When you turn the camera on, various icons are shown on the
LCD screen to indicate the current camera settings and status.
To learn more about the displayed icons, see “LCD Screen display” on page 24.
LCD Screen notes:
Extremely high-precision technology had been used to
manufacture the LCD screen so that most of the pixels are
operational for use. However, there may be some minute
points (black, white, red, blue or green) that constantly
appear on the LCD screen. These points are normal in the
manufacturing process and the recording is not aected in
any way.
Avoid exposing the LCD screen to water; please remove
any moisture on the LCD screen with dry and soft
cleaning cloth.
If the LCD monitor is damaged, take particular care
with the liquid crystal in the monitor. If any of the
following situations arise, take the recommended
immediate action indicated below:
• If liquid crystal comes in contact with your skin, wipe the
area with a cloth and then wash thoroughly with soap and
running water.
• If liquid crystal gets into your eye, ush the aected eye
with clean water for at least 15 minutes and then seek
medical assistance.
• If liquid crystal is swallowed, ush your mouth thoroughly
with water. Drink large quantities of water and induce
vomiting. Then seek medical assistance immediately.
16171617
BASIC OPERATION
Shooting in Auto Mode
Auto mode is the easiest mode to take photos. While
operating in this mode, the camera automatically optimizes
your photos for best results.
To start shooting, do the following:
1. Press
Power to turn the camera on.
2. In the Mode menu, select the Auto mode ( ).
3. Compose your picture on the LCD screen and press the
Shutter button halfway to focus on the subject.
4. The LCD screen will show green focus frame after the
subject is in focus.
5. Press Shutter fully to capture the image.
Using the Zoom Function
Your camera is equipped with two types of zoom functions:
optical zoom and digital zoom. Press the Zoom button of the
camera to zoom in or out on the subject while taking pictures.
Zoom button
Zoom indicator (See
“Digital Zoom“ on
page 41)
When the optical zoom reaches its maximum value, release
the Zoom button then press it again for it to go further at the
digital zoom. Zoom indicator is hidden after the Zoom button
is released. The screen shows ( ) for the current zoom
status.
Basic Functions Menu
The Basic Function Menus of the camera include Flash, Selftimer, Macro Capture, and Exposure Compensation. The
suitable function setting can let you shoot better photos.
Set the basic functions as per the following steps:
1. Pull up the Basic Function Menus by pressing Right/Flash
button.
4. Press Left/Right button to select the basic functions
required to set, press Up button to enter the setting
screen for selecting basic functions, or press button to
conrm the settings and exit the screen.
Flash
2. Press Left/Right button to select the settings of the
required function.
button to conrm the settings and exit the menu,
3. Press
or press Down button to enter the selection screen of Basic
Function
1819
• Flash : Auto
Camera ash goes o automatically based on
existing light conditions.
• Flash : Red-eye reduction
The camera exposes a brief ash before the picture
is taken to reduce red-eye eects.
• Flash : Forced ash
Flash always goes o.
• Flash : Forced o
Flash is turned o.
• Flash : Slow Synchro
This allows you to take pictures of people at night
that clearly show both your subjects and the night
time backdrop.
• Flash : Red-Eye + Slow Synchro
Using this mode for slow synchro shots with red-eye
reduction.
Self-timer/Continuous Capture
• Self-time : 2 sec
A single picture is shot 2 seconds after the Shutter
button is pressed.
• Self-time : 10 sec
A single picture is shot 10 seconds after the Shutter
button is pressed.
• Self-time : Continuous Shot
Pictures are shot continuously when the Shutter
button is pressed down based on the Continuous
Shot settings in the menu. (See “Continuous Shot” on
page 39).
• Self-time : O
Disable the self-timer.
Macro Mode
• Macro : On
Select this to focus on subjects 5cm from the lens.
• Macro : O
Select this option to disable Macro.
Exposure Compensation
The exposure compensation allows you to adjust the light
exposure value and shoot the best photo.
The adjustable range of exposure value is from EV -2.0 to
EV+2.0.
Advanced Functions Menu
The Advanced Functions Menu of the camera include Image
Size, Image Quality, White Balance, Image Color and ISO etc.
The suitable function setting can let you shoot better photos
and videos.
Set the advanced functions as per the following steps:
1. Pull up the Advanced Function Menus by pressing
button.
4. Press Left/Right button to select the advanced functions
required to set, press Up button to enter the setting screen
for selecting advanced functions, or press button to
conrm the settings and exit the screen.
2. Press Left/Right button to select the settings of the
required function.
3. Press button to conrm the settings and exit the
menu, or press Down button to enter the selection screen
of Advanced Functions.
2021
WB (White Balance)
The White Balance allows you to adjust the color temperature
under dierent light source to ensure faithful color
reproduction.
The options of White Balance include:
• WB : Auto
• WB : Daylight
• WB : Cloudy
•WB : Fluorescent
•WB : Fluorescent CWF
•WB : Incandescent
•WB : Manual (Press the shutter button to set WB)
ISO
The ISO function allows you to set the sensitivity of the camera
sensor based on the brightness of the scene. To improve the
performance in darker environments, a higher ISO value is
required. On the other hand, a lower ISO value is needed when
in bright conditions.
Pictures at higher ISO will naturally have more noise than
those at lower ISO.
The options of ISO include automatic, 80, 100, 200, 400, 800
and 1600.
The available ISO values vary on dierent camera
models.
Loading...
+ 54 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.