GE AZ32H15E5DM1, AZ32H15E5BM2, AZ32H15E5BM1, AZ32H15E4DM1, AZ32H15E4CM2 Owner’s Manual

O

Zoneline Series

Heat Pump Model 3200

Heat/Cool Model 2200

Zoneline

Owner's Manual

Important Safety information

Operating Instructions

The OontroL_ on Yo_r ZoneH_m

Oa_ o{ Predator

Installation Instructions

Helpful Information

Thi_gs Tha__Are

If SomethingGoesWrong

BeZoye Yow ...... _oywce

GE Serdce _w_mness

GEAnswer Center ®

800.626.2000

GEAppliances

49-7359

we believe in dependable service.

You'll see it in this easy-to-use
manual and you'll hear it in the
friendly voices of our customer
service department.

the comff)rt of your Zoneline.
That's important, because your
new Zoneline will be part of your
family for a long time.

Before using

yo_g

Zoneline

Staple your receipt to the inside back
cover of this manual You will need it

to obtain service under warranty.

Write down the model and serial

numbers here. They are on a label

behind the room cabinet on the
base pan.

Model number

Serial number

Date of purchase

ii _ il

Hglp 1is

help you

800.626.2000

2

Befi)re you call for service,
there are a few things you can
do to help us serve you better.

Read this manual It contains
instructions to help you use and

maintain your Zoneline properly.

Save time and money. Check the
section titled ff Something Goes

Wrong before calling. This section

was designed to solve common

problems that might occur.

If you do need service, you can
relax knowing help is only a phone
call away. Toll-free customer service

numbers are included in the back
of this manual. Or call the GE

Answer Center ® at 800.626.2000,

24 hours a day, 7 days a week.

READ ALL SAFE TY INFORMA TION

BEFORE USING

• This Zoneline must be properly • Unplug or disconnect the
installed in accordance with the Zoneline at the fuse box or

Installation Instructions before it circuit breaker before making
is used. See pages 10-12.

any repairs.

• Repair or replace immediately
all electric service cords that have

become ficayed or otherwise
damaged.

SAVE

THE SE INS TR UCTI ONS

For details see the Installation
Instructions in the back of this

manual.

NOTE:We strongly recommend

that any servicing be pertbrmed

by a qualified individual.

3

The

controls

TEMP CONTROLS MODE CONTROLS

LOW

FAN

STOPt

HIGH

• FAN

On yO! T

Zoneline

A TempControl

The temp control is used to maintain the
room temperature. The compressor will cycle
on and off to keep the room at the same level
of comfort. When you turn the knob to COOLER

(blue) the indoor air will become cooler. Turn

the knob to WARMER (red) and the indoor air

will become warmer.

3200Series on/y

When the outdoor temperature is lower than
25°F., heat is provided by the electric heater in
the air conditioner instead of by the heat pump.

LOW•

HEAT

HIGH

DLOW

COOL

HIGH

A Mode Control

HiGH COOLand LOW COOLprovide cooling with

different fan speeds.

HiGH HEATand tOW HEATprovide heating with
different fan speeds.

LOW FAN or HIGH FANprovides air circulation
and filtering without cooling or heating.

NOTE:

ff you move the switch from a cool or heat
setting to STOP or to a fan setting, the unit has
an automatic 3=minute delay before allowing the
compressor to restart in the cool or heat mode.

EnergyTip

Vent

control

Louverscrews

Removethe room cabinet and

flip the louvers to change the air direction.

A Ventilation Control

The ventilation control lever is located at the

lower left side of the Zoneline unit, behind the
room cabinet.

When set at CLOSE, only the air inside the room

is circulated and filtered.

When set at OPEN,some outdoor air will be

drawn into the room. This will reduce the
heating or cooling egiciency.

Air Direction

To adjust the air direction, remove the room
cabinet. Remove the 7 louver screws that

hold the louvers in place. Flip the louver
section 180 °, replace the screws and the

room cabinet.

5

Other Zoneline features

Heat pumps can save money by
removing heat from the outside

air-even when the outside
temperature is below freezing-

and releasing that heat indoors.

To get the best performance from

your heat pump, don't change the

room thermostat vet y often.
Raising the heat setting 2-3
degrees will cause the Zoneline to
use its electric heating elements in
order to reach the new temperature

setting quickly.

Additional controls are located

behind the room cabinet.

To remove: Pull out at the bottom to

There is a three minute minimum
compressor run time at any setting

to prevent short cycling.
The indoor fan motor starts before

the compressor and stops after the
compressor cycles off.

The electric heating elements use
much more electricity than heat
pumps and cost more to operate.

To replace: Place the tabs over

the top rail. Push inward at the
bottom until it snaps into place.

release it from the tabs. Then lift up.

The auxilia[ T controls are located behind the room cabinet on the front of
the unit control box. The factory settings will be in the DOWNposition. The
owner is responsible for checking switches and ensuring they are in the
desired position.

123456

UP

DOWN

*All E
UP:Fan cycle

DOWN:F
RemoteCq

(Class 2)

*Not on Model 2200 Series

Load Shedding)

1B23456

IIaaaaIoow.

Auxiliary Controls

Down--Continuous Fan
Up--Cycle Fan

123456

FIBFIBFIII]oowN

UP

UP

The fan switch #2 is located behind
the room cabinet.

This switch is set at continuous fan

(DOWN) at the factory to provide

continuous fan operation in cool
or heat modes. Leaving the switch
in the continuous fan setting allows

continuous circulation of room air
and will resuh in a more balanced

temperature throughout the room.

Switch #6 controls the Freeze
Sentinel. When the switch is DOWN,

the Freeze Sentinel automatically
turns on the resistance heater and

fan if the room temperature (sensed
at the unit) drops to approximately

40 ° F. It will turn the heater offwhen
the temperature reaches about 45 ° F.

The unit leaves the factory with
the Freeze Sentinel in the DOWN

(on) position.

If you want the fan to cycle on
and offwith the compressor or

with the heater, move the switch

to cycle fan (UP).

The Freeze Sentinel helps prevent
plumbing damage in the room due
to sub-freezing temperatures.

If the Freeze Sentinel is set, it is

active as long as power to the
unit is on.

NOTE: The owner is responsible for
checking the Freeze Sentinel switch
and ensuring it is in the desired

setting. 7

&

Cleaning

Turn the Zoneline off and discon-
nect the power supply.

The coils on the outdoor side of
the Zoneline should be checked

regularly. If they are clogged with
dirt or soot they may be profes-
sionally steam cleaned, a seiMce
available through your GE seiMce

outlet. You will need to remove
the chassis to inspect the coils

because the dirt build-up occurs
on the inside.

To clean, use water and a mild
detergent. Do not use bleach or

abrasives. Some commercial
cleaners may damage the plastic

parts.

Clean the outside coils
regularly.

In some installations, dirt or other
debris may be blown into the unit

from the outside and settle in the
base pan (the bottom of the unit).
In some areas of the United States
a "jell-like" substance may be seen

in the base pan.

Check it periodically and clean it
out, if necessai T.