<![endif]>AIR CONDITIONER
<![if ! IE]><![endif]>Portable Room
IMPORTANT SAFETY INFORMATION . . . . . . . . . . . . . 3
USING THE AIR
CONDITIONER . . . . . . . . . . . . . . 4 CARE AND CLEANING . . . . . . . 7
INSTALLATION
INSTRUCTIONS . . . . . . . . . . . . . 9 TROUBLESHOOTING . . . . . . . 13 WIFI SETUP . . . . . . . . . . . . . . . 14 LIMITED WARRANTY . . . . . . . .15 CONSUMER SUPPORT . . . . . . .16
Before you begin (on some models)
Record the GE module number and password for wifi setup. To locate this information, see pages 13 and 14.
GE Module Number #____________
Password #____________________
Write the model and serial numbers here:
Model #_________________
Serial # _________________
Find these numbers on a label on the side of the air conditioner.
OWNER’S MANUAL AND INSTALLATION INSTRUCTIONS
APCA09
APCA10
APCA12
APWA12
GE is a trademark of the General Electric Company. Manufactured under trademark license.
49-5000440 Rev. 2 09-20 GEA
THANK YOU FOR MAKING GE APPLIANCES A PART OF YOUR HOME.
Whether you grew up with GE Appliances, or this is your first, we’re happy to have you in the family.
We take pride in the craftsmanship, innovation and design that goes into every GE Appliances product, and we think you will too. Among other things, registration of your appliance ensures that we can deliver important product information and warranty details when you need them.
Register your GE appliance now online. Helpful websites and phone numbers are available in the Consumer Support section of this Owner’s Manual. You may also mail in the pre-printed registration card included in the packing material.
2 |
|
49-5000440 Rev. 2 |
|
IMPORTANT SAFETY INFORMATION
READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE
IMPORTANT SAFETY INSTRUCTIONS
WARNING To reduce the risk of fire, electrical shock, injury to persons, or damage when using the air conditioner, follow basic precautions, including the following:
•Read all of the instructions before using this appliance.
•Plug into a grounded 3 prong outlet.
•Do not remove ground prong.
•Do not use an adapter.
•Do not use an extension cord.
•Do not operate the air conditioner if it has a damaged cord or plug, if it is not working properly, or if it has been damaged or dropped.
•The air conditioner should be serviced only by qualified service personnel. Call an authorized service company for examination, repair, or adjustment.
•Disconnect power before servicing.
•Disconnect power before cleaning.
NOTE: Turning off power by pressing the Power button does NOT disconnect the appliance from the power supply.
•Do not install or use the air conditioner in any area where the atmosphere contains combustible gases or where the atmosphere is contaminated. Avoid any chemicals coming in contact with your air conditioner.
•Do not store anything directly on top of the air conditioner.
•Use two or more people to move and install air conditioner.
•Never operate the air conditioner without the filters in place.
•Do not use the air conditioner near a bathtub, shower or wash basin or other wet area.
READ AND SAVE THESE INSTRUCTIONS
<![endif]>INFORMATION SAFETY IMPORTANT
49-5000440 Rev. 2 |
3 |
<![endif]>USING THE AIR CONDITIONER
Controls
Features and appearance will vary.
Lights next to the touch pads on the air conditioner control panel indicate the selected settings.
A
Cool Fan Dry |
|
|
|
|
|
Low Med High |
|
|
|
Temp / Time |
|
|
|
|
|
|
|
|
|
B C D E F G H (on some models)
B C D A
Controls
A. CONTROL PANEL DISPLAY
Displays the Set Temperature in degrees Fahrenheit or the hours remaining in a Time Delay. The corresponding indicator light will illuminate.
B. Power Button
Turns ON/OFF power to the air conditioner. NOTE: Turning off power by pressing the Power button does NOT disconnect the appliance from the power supply.
•Press the Power button. The Power indicator will illuminate.
C. Mode Button
Press the Mode button to toggle among the operating options. The corresponding indicator will illuminate: Cool – Cools the room to the set temperature
Dry – Reduces the humidity in the room
Fan – Circulates the air in the room without cooling.
D.Remote Control Signal Receiving Window
Aim the Remote Control at this window so the Control will receive the signal.
E.Up and Down Arrow Buttons
Adjusts the Temperature or Hours in Time Delay.
To Set the Temperature:
The temperature can be set between 64ºF and 86ºF (18ºC and 30ºC) when the air conditioner is in Cool mode.
1.Press the Mode button until the Cool mode is selected.
2.Press the Up Arrow or Down Arrow buttons to select the Temperature.
NOTE: The temperature cannot be set when the air conditioner is in either Fan or Dry mode.
E F G
F.Fan Speed Button
The fan speed can be adjusted from Low speed, Medium speed, to High speed when the air conditioner is either in Cool or Fan mode.
NOTE: The fan speed cannot be adjusted when the unit is in Dry mode.
•Press the Fan Speed button to toggle among the three speeds. The corresponding fan speed indicator will illuminate.
G.Timer Button
Program a time from (1-hour to 24-hours) for the air conditioner to turn Off or On. When a Time Delay is programmed, the Timer indicator light will illuminate.
While the air conditioner is operating:
1.Press the Timer button.
2.Press the Up/Down arrow buttons to select the number of hours you want the air conditioner to continue to operate before turning Off.
NOTE: Wait approximately 5 seconds for the Turn-Off time to be saved.
While the air conditioner is off:
1.Press the Timer button.
2.Press the Up/Down arrow buttons to select the number of hours you want the air conditioner to remain off before turning On.
NOTE: Wait approximately 5 seconds for the Turn-On time to be saved.
To cancel the timer:
•Press the Timer button once, the hours remaining will flash, press the timer button again and the timer will be canceled.
H. WiFi Connect Pad (on some Models)
1.Press and hold the timer button for 3 seconds to connect the app or disconnect the app.
2.Connect your air conditioner to WiFi router.
Refer to the “WiFi Set up” section for more information.
4 |
49-5000440 Rev. 2 |
Controls
The display will always default to show the room temperature.
When the air conditioner is turned on, it will automatically start in the last mode and fan settings selected.
Cool Mode
Use the COOL mode for cooling.
To set the COOL mode:
1.Press the MODE pad until the COOL indicator light is lit.
2.Press the FAN pad to set HIGH, MEDIUM, or LOW fan speed.
3.Press + or - to set the desired temperature between 61°F and 89°F in 1°F increments.
After settings have been made, the display will change back to show the room temperature.
The temperature control is used to maintain the room temperature. The compressor will cycle on and off
to keep the room at the set level of comfort. Set the temperature control at a lower number and the indoor air will become cooler. Set the temperature control at a
higher number and the indoor air will become warmer. NOTE: If the air conditioner is off and is then turned on while set to COOL, it will take approximately 3 minutes for the compressor to start and cooling to begin.
Cooling Descriptions
For Normal Cooling—Select the COOL mode and HIGH, MEDIUM, or LOW fan speed with a middle set temperature.
For Maximum Cooling—Select the COOL mode and HIGH fan speed with a lower set temperature.
For Quieter & Nighttime Cooling—Select the COOL mode and LOW fan speed with a middle set temperature.
NOTE: If you switch from COOL or DRY mode setting to OFF, wait 3 minutes before restarting.
DRY Mode—Dehumidification
Use the DRY mode to provide dehumidification only. The fan will run at a fixed speed at this setting, so a fan speed cannot be set. Keep windows and doors closed for the best dehumidifying effects.
To set the DRY mode:
•Press the MODE pad until the DRY indicator light is lit.
In the DRY mode, a set temperature will not be displayed. After DRY mode has been set, the display will change back to show the room temperature.
NOTE: If you switch from a DRY setting to OFF or to a
fan setting, wait at least 3 minutes before switching back to a DRY setting.
If using the unit in the DRY mode as a dehumidifier for an extended time.
1 .Unplug the power cord.
2.Connect a drain hose to the upper drain port (see page 10, upper drain #11) and lead hose to floor drain.
3.Reconnect the power cord and press the MODE pad until the DRY indicator light is lit.
FAN Mode
Use the FAN mode to provide air circulation and filtering without cooling.
To set the FAN mode:
•Press the FAN pad until the desired indicator light for HIGH, MEDIUM, or LOW fan speed is lit.
Since fan only settings do not provide cooling, a set temperature will not be displayed. After FAN speed has been set, the display will change back to show the room temperature. The exhaust hose and window kit do not need to be installed when operating in fan mode.
Power Outage Recovery Feature
In the case of a power outage or interruption, the unit will |
NOTE: If the TIMER was set before the power outage, it |
automatically re-start in the settings last used after the |
will need to be reset after power is restored. |
power is restored. |
|
<![endif]>CONDITIONER AIR THE USING
49-5000440 Rev. 2 |
5 |
<![endif]>USING THE AIR CONDITIONER
Controls
Features and appearance may vary.
Icons on the remote control indicate the selected settings.
|
Swing |
Fan Speed |
|
|
Cool |
|
|
A |
Fan |
C |
|
B |
|||
|
|
||
C |
Dry |
|
|
D |
Heat |
|
|
E |
|
||
|
|
||
F |
|
|
REMOTE CONTROL
1.Insert the two batteries (provided).
2.Aim the remote control at the signal receiver on the control panel to operate the air conditioner.
A.Power
Turns ON/OFF power to the air conditioner.
NOTE: Turning off power by pressing the Power button does NOT disconnect the appliance from the power supply.
•Press the Power button. The Power indicator will illuminate.
B. Mode
Press the Mode button to toggle among the operating options. The corresponding indicator will illuminate:
Heat (on some models) - Heats the room to the set temperature
Cool – Cools the room to the set temperature DRY – Reduces the humidity in the room
Fan – Circulates the air in the room without cooling
C.Temperature
Adjusts the Temperature or Hours in Time Delay.
To Set the Temperature:
The temperature can be set between 64ºF and 86ºF (18ºC and 30ºC) when the air conditioner is in Cool mode.
1.Press the Mode button until the Cool mode is selected.
2.Press the Up Arrow or Down Arrow buttons to select the Temperature.
NOTE: The temperature cannot be set when the air conditioner is in either Fan or DRY mode.
D. Fan Speed
The fan speed can be adjusted from Low, Medium, to High speed when the air conditioner is in operation.
NOTE: The fan speed cannot be adjusted when the unit is in DRY mode.
•Press the Fan Speed button to toggle among the three speeds. The corresponding fan speed indicator will
illuminate.
E. Timer
Program a time from (1-hour to 24-hours) for the air conditioner to turn Off or On. When a Time Delay is
programmed, the Timer indicator light will illuminate.
F. Swing Button
The louvers on your portable air conditioner will open automatically (do not pry them open or push them shut).
Use the Swing Button on your remote to adjust the louvers in the position you would like them to be in, or to operate in Swing mode the louvers will continue to move up and down.
6 |
49-5000440 Rev. 2 |
Care and Cleaning
CLEANING
WARNING
Electrical Shock Hazard
Disconnect power before cleaning.
Failure to do so can result in death or electrical shock.
1.Unplug or disconnect power.
2.Use only a soft cloth dampened with water to clean the cabinet.
NOTE:
•Do not use a liquid or spray cleaner to clean the air conditioner.
•DO NOT use chemicals, abrasives, ammonia, chlorine bleach, concentrated detergents, solvents or scouring pads. Some of these chemicals/items may damage and/or discolor your air conditioner.
3.Dry thoroughly with a soft cloth.
4.Plug in or reconnect power.
Air Filter
The air filters should be cleaned at least every two weeks for your unit to operate at optimum efficiency.
CAUTION DO NOT operate the air conditioner without a filter because dirt and lint will clog it and reduce performance.
To remove:
1.Unplug or disconnect power.
2.Pull to remove upper filter panel.
3.Wash or vacuum the dust from the air filters.
NOTE: If washed, gently shake the filter to remove the excess water and dust particles trapped in the filter.
4.Reinstall the filters.
5.Plug in or reconnect power.
<![endif]>CLEANING AND CARE
49-5000440 Rev. 2 |
7 |
<![endif]>CARE AND CLEANING
Care and Cleaning
Internal Water Tank
The Water Full indicator (“FL” on the control panel display) illuminates when the internal water tank has filled with condensed water.
To Empty the Internal Water Tank:
1.Unplug or disconnect power.
2.Place a shallow 1 quart or larger pan (not included) below the lower drain located on the back (near the bottom) of the air conditioner.
3.Remove the cap and the rubber plug and drain the water tank.
4.Re-insert the drain plug and screw the cap snugly into place.
5.Plug in or reconnect power.
Storage
If the unit is not being used for a long period of time: To Empty the Internal Water Tank:
1.Unplug or disconnect power.
2.Drain the water from the water tank. (See “Internal Water Tank section” above.)
3.Use the original packaging to repack the unit to avoid a buildup of dust or dirt.
4.Store the air conditioner in a cool, dry location.
How to Insert the Batteries in the Remote Control
1.Remove the battery cover by sliding it according to the arrow direction.
2.Insert new batteries, making sure that the (+) and (–) of battery are installed correctly.
3.Reattach the cover by sliding it back into position.
NOTES:
Ŷ 8VH ³$$$´ YROW DONDOLQH EDWWHULHV 'R QRW XVH rechargeable batteries.
Ŷ 5HPRYH WKH EDWWHULHV IURP WKH UHPRWH FRQWURO LI WKH system is not going to be used for a long time.
Ŷ 'R QRW PL[ ROG DQG QHZ EDWWHULHV 'R QRW PL[ DONDOLQH standard (carbon-zinc) or rechargeable (ni-cad, ni-mh, etc) batteries.
8 |
49-5000440 Rev. 2 |
Installation Instructions
Questions? Call GE Appliances at 800.GE.CARES (800.432.2737) or visit our Website at: GEAppliances.com. In Canada, call 1.800.561.3344 or visit our Website at: www.GEAppliances.ca
BEFORE YOU BEGIN
Read these instructions completely and carefully.
• IMPORTANT — Save these instructions for local inspector’s use.
• IMPORTANT — Observe all governing codes and ordinances.
•Note to Installer – Be sure to leave these instructions with the Consumer.
•Note to Consumer – Keep these instructions for future reference.
•Skill level – Installation of this appliance requires basic mechanical skills.
•Completion time – Approximately 1 hour
•We recommend that two people install this product.
•Proper installation is the responsibility of the installer.
•Product failure due to improper installation is not covered under the Warranty.
•You MUST use all supplied parts and use proper installation procedures as described in these instructions when installing this air conditioner.
ELECTRICAL REQUIREMENTS
Some models require a 115/120-volt AC, 60-Hz grounded outlet protected with a
15-amp time-delay fuse or circuit breaker.
The 3-prong grounding plug minimizes the possibility of electric shock hazard. If the wall outlet you plan to use is only a 2-prong outlet, it is your responsibility to have it replaced with a properly grounded 3-prong wall outlet.
CAUTION
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.
Do not change the plug on the power cord of this air conditioner.
Aluminium house wiring may present special problems—consult a qualified electrician.
|
Power cord includes a current |
|
RESET |
interrupter device. A test and reset |
|
button is provided on the plug case. |
||
|
||
TEST |
The device should be tested on |
|
|
a periodic basis by first pressing |
|
|
the TEST button and then the |
|
|
RESET button while plugged into |
|
|
the outlet. If the TEST button does |
|
|
not trip or if the RESET button will |
|
|
not stay engaged, discontinue use |
|
|
of the air conditioner and contact a |
|
|
qualified service technician. |
Location Requirements
•Place the air conditioner on a flat, level surface in a location that is at least 30” (76.2 cm) from any wall.
NOTE: A minimum clearance of 30” (76.2 cm) from the air conditioner to the wall must be maintained to ensure proper airflow.
•Maintain a minimum 30” (76.2 cm) clearance around the air conditioner to not block airflow.
•Keep the air conditioner free of any obstructions such as drapes, curtains, blinds, etc.
•The exhaust hose should be free of any obstructions.
•Do not place the air conditioner on an unstable or raised surface because it could fall and cause damage or injury.
•Do not place the air conditioner in direct sunlight or near a heat source such as baseboard heaters, stoves, etc.
•The window panel can be installed in a window with a minimum 20” (55.88 cm) to a maximum 46” (121.92) opening.
20" |
20" |
|
|
(55.88 cm) |
|
<![endif]>INSTRUCTIONS INSTALLATION
49-5000440 Rev. 2 |
9 |
<![endif]>INSTALLATION INSTRUCTIONS
Installation Instructions
PARTS INCLUDED
(Appearance may vary)
1
2
3
6
9
7
8 11
10
12
13
14
1. |
Control Panel |
6. |
Remote Control |
2. |
Swing Air Louvers |
7. |
Filter Panel |
3. |
Casters |
8. |
Power Cord Hook (2) |
4. |
Exhaust hose assembly |
9. |
Handle (2) |
4 |
10. Air Vent - exhaust |
|
|
11. Continuous Drainage hole |
|
|
12. Air inlet grille |
|
|
13. |
Drainage hole |
5. Window sealing plate assembly |
14. |
Power Cord and plug |
|
15. |
Small Screw |
|
|
15 |
5 |
|
|
10 |
49-5000440 Rev. 2 |