GE AMV06 Use and Care Manual

Page 1
Iu
se and Care& Installation Guide
Contents
Room Air Conditioner
Adapter Plug Air Direction
(;are
and Cleaning
Air Filter
C;nlle &
Outdoor
Consumer Services 15 Control Settings
Electrical Requirements Energy-Saving
Extension Cords Freezing Up
Grounding Installation Instructions
Model and Serial Numbers Problem Solver
Safety Instructions User Maintenance Instructions
Warranty
GE Answer
800.626.2000
(labinet
(:oil
‘1’ips
Centera
Back
4,5
8-14
(;over
:3
5
2 6
6 6
6
:3
7
3
5
:3
2
7 2
f;
Model
AW06
GE Appliances
Page 2
Help us help you...
MPORTANT
Hyou need
sertice
Before using your air conditioner, read this book carefully.
It is intended to help you operate and maintain your new air
conditioner properly.
Keep it handy for answers to your
questions.
If
you don’t understand something or need more help, write (include your phone number):
Consumer Affairs GE Appliances Appliance Park Louisville, KY 40225
Write down the model and serial numbers.
You’ll find them on a label on the lower right hand side of the outer cabinet.
These numbers are also on the Consumer Product Ownership
Registration Card that came with
your air conditioner. Before
sending in this card, please write
these numbers here:
Model Number
Serial Number
Use these numbers in any correspondence or service calls concerning your air conditioner.
If you received a damaged air conditioner...
Immediately contact the dealer (or builder) that sold you the air conditioner.
Save time and money. Before you requ~t service...
SAFETY
mSTRUCTIONS
Read all instructions before using this appliance.
When using this appliance, always exercise basic safety precautions, including the following:
Use this appliance only for its
intended purpose as described
in this Use and Care Guide.
This air conditioner must be properly installed in accordance with the Installation hstructions before it is used. See grounding instructions.
Never unplug your air conditioner by pulling on the power cord. Always grip plug firmly and pull straight out from the receptacle.
Repair or replace immediately all electric service cords that have become frayed or otherwise damaged. Do not use a cord that
shows cracks or abrasion damage along its length or at either the plug or connector end.
s
Unplug your air conditioner before making any repairs. Note: We strongly recommend that any servicing be by a qualified individual.
For your safety..
or use combustible materials, gasoline or other flammable vapors or liquids in the vicinity of this or any other appliance.
perfomed
.do
not store
To obtain service, see the Consumer Services page in the back of this book.
We’re proud of our service and want you to be pleased. If for some reason you are not happy with the
service you receive, here are three steps to follow for further help.
FIRST, contact the people who
serviced your appliance. Explain why you are not pleased. In most
cases, this will solve the problem.
NEXT, if you are write all the details—including your phone number—to:
Manager, Consumer Relations GE Appliances Appliance Park Louisville, KY 40225
FINALLY, if your problem is still not resolved, write:
Major Appliance Consumer
Action Panel 20 North Chicago, IL 60606
still
Wacker
not pleased,
Drive
Check the Problem Solver
section of this guide. It lists causes of minor operating problems that you can correct yourself.
2
SAVE THESE
~STRUCTIONS
Page 3
Electrical
Safety—MPORTANT...pleaSe
Read
Carefully.
How to connect electricity
For personal safety, this appliance must be properly grounded.
Electrical requirements
115-volt models require a
volt
a.c.,
60 hz grounded outlet protected with a
fuse
or circuit breaker.
The
power cord on these models has a three-prong (grounding) plug that mates with a standard three-prong (grounding) wall outlet (Fig. 1) to minimize the possibility shock hazard from these appliances.
PREFERRED , METHOD
Fig. 1
Where a standard two-prong wall outlet is encountered, it is your personal responsibility and obligation to have it replaced with a properly grounded three-prong wall outlet.
IS
amp time delay
DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR REMOVE THE THIRD (GROUND) PRONG FROM THE POWER CORD.
230/208-volt models
own single branch circuit supplying 230/208-volt time delay fuse or circuit breaker. This is recommended performance and to prevent overloading house wiring circuits, which could cause a possible fire hazard from overheating wires.
The power cord on these models has a 230/208-volt perpendicular,
tandem
or
a.c.,
protected with a
large
tandem type plug
115/120-
of
electric
QQ +’
<,
n
INSURE PROPER GROUND EXISTS BEFORE USE
require their
for
best
r
that mates respectively with a 230/208-volt perpendicular, tandem or large tandem type wall outlet. These types available at most hardware stores.
230/208-VOLT
>ERpENDlcu~R
LINE CORD PLUG
REQUIRES 20 AMP TIME DELAY FUSE
OR CIRCUIT BREAKER PROTECTION
. . . .
230/208-VOLT
TANDEM TYPE
LINE CORD PLUG
REQUIRES 15 AMP TIME DELAY FUSE
OR CIRCUIT BREAKER PROTECTION
230/208-VOLT
LARGE TANDEM TYPE WALL OUTLET
LINE CORD PLUG REQUIRES 30 AMP TIME DELAY FUSE
OR CIRCUIT BREAKER PROTECTION
Whether your air conditioner is a 115-volt or a 230/208-volt unit, it is important to have the wall outlet and circuit checked by a qualified electrician if there is any doubt as to whether a proper ground exists.
of outlets are
~pE
MATCHING
WALL OUTLET
MATCHING
WALL OUTLET
MATCHING
Use of adapter plug (115-volt models only)
Because of potential safety hazards under certain conditions, we
strongly recommend against use of an adapter plug. However, if
you still elect to use an adapter, where local codes permit, a TEMPORARY CONNECTION may be made to a properly grounded two-prong wall outlet by use of a
UL listed
at most local hardware stores.
adapter
(Fig,
2) available
,.
TEMPORARY METHOD (ADAPTER PLUGS NOT
PERMITTED IN CANADA
ALIGN LARGE
PRONGS/SLOTS
Fig. 2
The larger slot in the adapter must be aligned with the the wall outlet to polarity in the connection of the power cord.
CAUTION: Attaching the adapter ground terminal to wall outlet cover screw does not ground the appliance unless cover screw is metal, and not insulated, and wall outlet is grounded through
house wiring. You should have the circuit checked by a qualified electrician to make sure the outlet is properly grounded.
When disconnecting the power cord from the adapter, always
hold the adapter with one hand. If this is not done, the adapter ground terminal is very likely to break with repeated use.
Should the adapter ground terminal break, DO NOT USE the appliance until a proper ground has again been established.
BEFORE USE
larger
prov;de
proper
1
slot in
Use of extension cords
Because of potential safety hazards under certain conditions, we
strongly recommend against the use of an extension cord.
However, if you still elect to use an extension cord, it is absolutely necessary that it be a UL listed 3-wire grounding type appliance extension cord and that the current carrying rating of the cord in amperes be equal to or greater than the branch circuit size shown on the rating nameplate of the appliance.
I
&
w
~
Page 4
Operating Your Air Conditioner Controls
HI FAN
\
LO COOL
9
HI
COO1
LO FAN
OFF
+ +
&
SELECTOR
Selector Switch
OFF
turns air conditioner off.
LO FAN provides low fan speed operation without cooling.
HI FAN provides high fan speed operation without cooling.
LO COOL provides cooling with low fan speed operation.
HI COOL provides cooling with
high fan speed operation.
cOOUR b
4
2
THERMOSTAT
5
7
Thermostat Control
When you move the Thermostat Control to the desired setting, the thermostat will automatically control the temperature of the indoor air. The higher the number selected, the cooler the indoor air will become.
-
OPEN VENT CLOSE
(ON THE LOWER RIGHT SIDE OF THE DISCHARGE GRILLE)
I
Ventilation Control
When you move the Ventilation Control to CLOSE, the vent door is closed and room will be circulated and conditioned. Moving the control to OPEN opens the vent door, allowing a small amount of indoor air to be exhausted from the room.
However, cooling effectiveness is reduced when this control is set at OPEN, so we suggest you don’t keep it there long+ specially in hot. humid weather.
only
the air inside the
I
4
Page 5
For normal cooling
1.
Set the Selector Switch at
HI COOL.
2. Set the Thermostat Control at the desired number (usually 4-6 is a good starting position). If room temperature is not satisfactory after a reasonable time, set the Thermostat Control at a higher number for a cooler room or at a
lower number for a warmer room.
3. Set the Ventilation Control at CLOSE except for brief periods
when you want to exhaust room air to the outside.
For maximum cooling
1. Set the Selector Switch at
HI COOL.
2. Turn the Thermostat Control to
8.
3. Set the Ventilation Control at CLOSE.
For quieter operation
1.
Set the Selector Switch at LO
COOL position.
2. Turn the Thermostat Control to the desired number.
3. Set the Ventilation Control at CLOSE.
For nighttime operation
During the cooler evening hours, we recommend that you set the Selector Switch at LO COOL for very quiet operation and the Thermostat Control at mid-range
(4 or 5). Set the Ventilation
Control at CLOSE.
For extreme temperatures
For greatest economy and best performance, we suggest you set the Selector Switch at HI COOL in extremely hot weather.
To adjust air direction
Up and down
UP-AND-DOWN
AIR DIRECTION
SIDE­AIR D
r
*
The up-and-down air direction
louvers are controlled by fingertip pressure on the louvers. They regulate air discharge upward, downward, or straight out.
Side to Side
Two separate banks of side-to-side
air direction louvers have separate
tabs to let you direct discharged
to the right, to the left, or straight
ahead.
*
ail
Freezing up
Outside air temperature dropping
If you notice that your air conditioner is not cooling as it should, it may be that ice has formed
on the cooling coils. The ice
blocks air flow and stops the unit from cooling the room. This “freezing up” is a temporary condition that most often occurs at night when the Thermostat is set at a higher number and the Selector is set on LO COOL.
To correct the condition, set the Selector at HI FAN or HI COOL and move the Thermostat to the
warmest setting.
Page 6
Care and Cleating
USER MAINTENANCE INSTRUCTIONS
~rn
air conditioner off and remove the plug from the wall outlet before cleaning.
Grille & Cabinet
Wipe front grille with a clean cloth lightly dampened with mild liquid
dishwashing
cabinet with mild soap or detergent and lukewarm water.
Outdoor Coil
detergent. Wash
Step
4:
Grasp the grille’s lower right and left corner and carefully lift straight upward to disengage the 2 top tabs from their slots in the cabinet front edge.
o
Step
5:
Mount the grille on front of the cabinet with the screw attached to grille during shipping, and slide the filter back into place.
This coil on the outdoor side
of the unit should be checked
periodically and cleaned if clogged with dirt or soot from the atmosphere. If extremely
soiled, it may need to be steam cleaned, a service available through your GE service outlet.
Front Grille
Remove
window sill prevents removal of the air filter.
To remove the grille:
Step 1:
that holds the grille to the chassis.
Step 2: Press inward on the lower right side of the cabinet until the tab is clear of the slot and allow the
grille to come toward you slightly.
Step 3: Repeat this process for the
lower left
Do you
to the
Oc(’ul:
the front grille if the
Remove and save the screw
side.
flot i)ull the
more
top 2 tubs
bottom
than 3
inches
of
ed,qe
or
the grille
toward
damage
may
To attach the grille: Step 1:
upward.
Step
right and left corner and carefully insert the VENT knob between the lower air direction louver and the grille frame, and engage two tabs on the grille’s top inside edge with two slots in the cabinet front edge.
Air Direction Louvers
w
Step 3: Press inward on the lower right side of the metal cabinet at the location of the slot and then carefully push the grille in until the tab engages with the slot.
Do not strike or plastic grille or damage to the tabs
will occur
Step 4: Repeat this process for the lower left side.
Set the air direction louvers
2:
Grasp the grille’s upper
Grille Frame “
FRONT VIEW
jorceably
SIDE VIEW
hit the
SCREW
Air Filter
The air filter behind the inlet grille should be washed at least every 30 days or as often as it needs cleaning.
To remove the filter,
on the filter and pull downward. the window sill blocks access to the air filter, you must first remove the front grille.
Vacuum the filter on the dusty side to remove light dust. Wash the filter, cleaner side up, under gently flowing water to wash out
accumulated dust and lint. If the
filter
is very dirty, use a mild household detergent in the wash water. Let the filter dry thoroughly
before replacing it. When replacing the filter, be sure
the word FRONT is facing you as you slide the filter back into place.
grasp the tab
If
6
Page 7
-
Ener~-Saving Tips
Keep the air filter clean.
For most efficient cooling,
keep the Ventilation Control in the CLOSE position except when
you want to exhaust air, smoke or odors from the room.
Don’t let the room get too
hot. Whenever possible, turn the unit on before the room heats up. When heat is “stored up” in walls, furniture, rugs and draperies, your air conditioner takes longer to produce the desired comfort condition.
Keep windows and doors
closed. Cool, dry air escapes when they’re open.
Keep furnace floor registers and
cold air returns closed. Cold air can easily escape through them.
Don’t let drapes or furniture
block the top or front of unit and restrict air flow when it
is operating.
It’s best to operate your air
conditioner at high speed during
extremely hot weather.
Keep the outdoor condenser
coil clean.
Turn air conditioner off before
vacations or extended absences from home.
Questions
m
~
~.
Use This Problem Solver
~
PROBLEM
AIR CONDITIONER DOES NOT OPERATE
AIR CONDITIONER “DOES NOT COOL AS IT SHOULD”
OPERATING SOUNDS
POSSIBLE CAUSE
Not plugged in. Plug may have been bumped
loose by vacuum cleaner or furniture.
If plugged in, fuse could have blown or
circuit breaker may have tripped.
Curtain, blinds or furniture blocking the top or
the front of the air conditioner will restrict airflow.
Thermostat Control may not be set high enough.
Move the knob to a higher number. Highest
setting should provide maximum cooling.
Air
filter
dirty, should be cleaned at least
every 30 days.
Room may have been very hot when air conditioner was first turned on. Allow time for it to cool down.
Cold air may be escaping through open furnace floor registers and cold air returns.
Ventilation Control may be set at OPEN
position, allowing hot outside air to enter the room.
Cooling coils have iced up. To melt ice,
move the Selector Switch to HI FAN and the Thermostat Control to a lower number.
Thermostat click, a metallic sound, may be
heard when compressor cycles on and off. This is normal.
Fan runs continuously when Selector
Switch is in COOL or FAN position.
This is normal.
WATER DRIPPING OUTSIDE
WATER DRIPPING INSIDE
WATER IN BASE PAN (ON OUTDOOR SIDE)
Excess water may
hot and humid weather. This is normal.
Air conditioner must be installed level or tilted
slightly to the outside for proper water disposal.
This is normal for a short period in areas with
little humidity; normal for a longer period in very humid areas. Moisture removed from indoor air drains to rear of cabinet where it is picked up by a fan and thrown against the outdoor condenser coil.
If you need more help...call, toll free:
GE Answer Center”
800.626.2000 consumer information service
ovefiow
in extremely
7
Page 8
INSTALLATION INSTRUCTIONS
BEFORE YOU BEGIN
Read these instructions completely and
carefully.
lMPORTANT–Observe
all governing codes
and ordinances.
lNSTALLER—Be
sure to leave these
instructions with the consumer.
CONSUMER–l{eep these instructions for
future reference.
ELECTRICAL REQUIREMENTS
FOR PERSONAL SAFETY:
THIS APPLIANCE MUST BE PROPERLY
GROUNDED. See grounding instructions.
DO NOT, UNDER ANY CIRCUMSTANCES,
CUT OR REMOVE THE THIRD GROUNDING PRONG FROM THE POWER CORD.
WE RECOMMEND THAT YOU DO NOT USE
AN EXTENSION CORD OR AN ADAPTER PLUG WITH THIS APPLIANCE.
DO NOT CHANGE THE PLUG ON THE
POWER CORD OF THIS APPLIANCE.
FOLLOW NATIONAL ELECTRICAL CODES
OR LOCAL CODES AND ORDINANCES.
WINDOW REQUIREMENTS
Standard double-hung window with actual
opening width of
Clear vertical opening of 14“ minimum from
bottom of sash to stool.
Install the air conditioner in a window where
there will be enough clearance around the cabinet to allow ample circulation of air through the unit.
1
t
.
25“ to 40”.
&’
25”
to
40”
*
14“
min.
i
I
Note: All supporting parts should be secured to
firm wood, masonry or metal.
I
115V
15 AMP c!rcuit 20 AMP circuit 15 AMP circuit 30 AMP circuit
“parallel” type “perpendicular” type “tandem” type “tandem” type
@@@@
If the electrical supply provided does not meet
the above specifications, call a licensed electrician.
Aluminum house wiring may pose special
problems–consult a qualified electrician.
This unit requires a separate circuit serving only
this appliance.
230V/208V 230V/208V
230
V1208V
8
Page 9
I
WINDOW INSTALLATION
TOOLS NEEDED
Ph
ill
ips
head screwdriver
Blade-type screwdriver
Sharp knife or razor blade
Rule or tape measure
Pencil
Typ
scr
Level
Box wrench
SCREWS FURNISHED (see samples)
Type A Type B
Qty-3
Qty-2 Qty-4
Type C
Type D
asket
%
Qty-6
Sealer (1
1/2
oz.)
Type A
screw
-
Right
window filler
panel
(continued next page)
9
Page 10
I
WINDOW INSTALLATION
REMOVEFRONTGRILLE
See Front Grille section.
PREPARE CHASSIS.
1. Remove chassis locking bracket and chassis locking screw with a Phillips head screwdriver. (Save for reuse.)
1. Install top mounting rail onto top of cabinet
with 3 Type D screws.
(co”t,nue~,
PREPARE CABINED
+
Room side
Top mounting rail
-
Chassis locking bracket
2. Remove ground screw and ground wire.
(Save for reuse.)
3. Remove chassis from cabinet using the base pan
as a handle.
Type D screw
Type D screw
2. Install bottom sill channel onto cabinet by
inserting notches on channel into slots located on bottom of cabinet and securing with 3 Type D screws.
0
Ill
~
10
Page 11
wArACH
1. Slide left window filler panel into top and bottom mounting rails.
2. Slide retainer panel into window filler panel and
attach to cabinet with 2 Type C screws.
3. Repeat for right side.
WIMDOWFIILER
PANELS.
5. Secure top mounting rail with two Type B screws
Ier
a
Top mounting rail
-t
Window filler panel
[
@
~
6
[
lNSMLL
1. Cut sealing ribbon to window width and stick it
to bottom of the lower window sash.
2. Measure and mark center of window sill to establish mounting position of cabinet.
3. Install cabinet into opening and center on line marked on window sill. Put top of cabinet toward you and lower window sash behind top mounting rail.
CABINETINWINDOM
Bottom mounting rail
Retainer panel
/NS~LL
Cut foam sash gasket to window width and stuff between top of lower sash and glass panes of upper sash Make sure foam gasket top of lower sash
SASH GASKEZ
IS
flush with
— Sealing
ribbon (ADHESIVE SIDE)
,
,
Center line
4. Extend and secure left and right window filler
panels to window sash with Type A screws, one on
each side.
/NS~LL
Install sash locking bracket using Type A screws
SASH LOCK
11
Type
A
screw
(continued next page)
Page 12
I
WINDOW INSTALLATION
INSMLL
1.
Slide chassis into cabinet. (Make sure tubing on
unit is not touching wall case. )
2. Lock chassis into cabinet by reinstalling chassis locking bracket and chassis locking screw removed in Step 2.
CHASSIS IN CABINED
Seal small openings around cabinet with gum-type sealer, provided.
See Front Grille section.
Chassis locking bracket
3. Reconnect ground wire removed in Step 2 to chassis.
4. Remove enough line cord to reach the wall receptacle.
(continued)
CHECKFORAIR
INSTALL
FRONTGRILIE
LEAKS.
12
Page 13
THROUGH-THE-WALL INSTALLATION
THE CABINET MAY BE INSTALLED
THROUGH THE WALL IN BOTH EXISTING
BUILDINGS AND NEW CONSTRUCTION.
lMPOR~NT
Any side louvers must project on the
side of the wall.
The room side of the cabinet must project into
the room at least 1“ from the finished wall.
The cabinet must be installed level from side to
side and with a 3/8” tilt from front to rear.
oudoor
PREPARE
1.
Determine size of opening.
height of cabinet and add 1/8” to each dimension.
WAll
OPENING.
Measure width and
TOOIS REOUIRED
Phillips head screwdriver
Blade-type screwdriver
9
Magnetic stud finder (optional)
Tin snips
Handsaw
Level
Chisel Concrete saw (if installing through a masonry wall)
Hammer
Caulking gun
Q
Tape measure
ADDITIONAL MATERIALS NEEDED
(obtain locally)
12 #10 wood screws, 1“ long
1 tube high grade caulking compound
Wooden framing studs
Lintel, if required, to support bricks or blocks
above opening
Flashing, aluminum or galvanized steel
2. Choose the wall power receptacle is (or will be) installed nearby.
3.
Make the opening. Frame it to support the
weight of the air conditioner. Add metal flashing over bottom of frame opening
and 1“ up on sides to reduce the possibility of moisture entering the area between the inner and outer wall. The flashing lip should be 1“ wide and bent down
1.
Remove chassis from cabinet. See Step 2 of
Window Installation.
2. With caulking compound or electrical tape, seal all holes provided in the cabinet for window installation hardware not used in this installation.
1.
Place cabinet in wall opening.
2. Secure cabinet bottom rail to wooden frame with two 1“ long #1 O wood screws.
45!
PREPARE THE CABINED
INSMLL
+
opening location. Be sure a
See the illustration, page 14.
CABINETIN WALL.
.=: s
.= ->:
~~= .>< .:.Z:
:<s,,%:
.,,. ,:...
:~:
;<:’$
,+:
‘?
-%
(continued next page)
13
Page 14
THROUGH-THE-WALL INSTALLATION
~ lNS~Ll
3. Secure cabinet sides to wooden frame with six
1“ long #1 O wood screws and secure cabinet top
to frame with four 1“ long #1 O wood screws.
Drill holes in cabinet sides and top, if necessary for proper installation. If frame is oversize, use shims to prevent cabinet distortion.
4. Caulk all four sides on the outdoor side of
cabinet to prevent moisture from getting
through to the interior wall. Use of flashing (a
piece of aluminum or galvanized steel available at most hardware stores) will further prevent moisture
from getting into interior walls.
5. Install wood trim molding (obtained locally)
around
CABINETIN WALL (continued).
,1
roomside projection of cabinet, if desired.
1
Brick Veneer —
Lintel Angle
‘if~:::::=
Caulking
Flashing Lip
~la~hing
4
Holes for #10
Wood Screws
-
Flashing
1
-1
----
..-
1“
Long
\
--- ——--— —-—
— . .
~:.:c
-—.
—..
. .
F-
i
\
o
-
(...,,.”,,,
ster
Line
Trim
Molding
(if desired)
INSIDE
SLIDE CHASSIS INTO CABINED
Lift the chassis and carefully slide it into cabinet. Do not push on controls or finned coils. Make sure
chassis is firmly seated toward rear of cabinet.
INSWIL
See Step 8 of Window Installation.
lNS~LL
See Care and Cleaning section.
CHASSIS IN CABINED
FILTER AND GRILLE
14
Page 15
Wdll
With the purchase
Be There
ofyour
new GE appliance, receive the assurance that if you ever need information or assistance from GE, we’ll be there. All you have to do is call–toll-free!
GEAnswer Centera
80~62E2000
In-Home
Repair
Service
80ME4ARES (80M32-2737)
A
GEconsumerservice
will provide
scheduled at a time that’s
for
you, Many GE company<) you service today or
your convenience weekdays,
days). Our factory-trained technicians
know your appliance inside so most repairs can be hanclled in just
one
visit.
exper[. repair service,
perated
9:()()
a.m. to
profkssi(ma]
convenient
(;onsumer
locations” off’er
tomorrow,”
(7:(}()
a.m. to
2:()()
Scmice
or at
7:()()
p.m.
p.m. Satur-
and
{)ut–
Service Contracts
80&626-2224
You c;in have the secure feeling that (;E (;onsunler
there
after
chase a ranty is
ii substan[.ial
year
contract, you’re assured of”future
setlice at
Service will still he
y(~ur
warranty expires. Pur-
(;E
contract while youl war-
still
in
effect
and
yc)u’11
discount. With a nlultiple-
today’s prices.
receive
Whatever
Inzijol” appliance, (;k; Answer
infi}rnl;~tion help.
will be answered pr(mlptly and
courtec)usly. And time. open 24
Telecommunication
Youl
(;E
Answer
l~t)LIrs ;i
yoLlr
question about any
se~~i(’e
is
avail~thle [()
call-and
yoLIr
yt)u
can c:ill any
(lenter’” selwicc
day, 7 days a week.
Detice
for
ques[ion-
tie
(;F
(;entel”’”
is
Deaf
Patis andAccessories
80&626-2002
IndividuA qufified
own appliances
parts
or
accessories sent directly to
their
home, free of ’shipping charge!
The
(1E
parts
to
over
47,()()()
Genuine Renewal Parts are fully warranted.
Discover cards arc accepted,
User maintenance instructions contained in this booklet cover proce­dures intended to be performed by any user. Other servicing
shodd
vice personnel. Caution must be exercised, since improper servicing may cause unsafe operation.
\JISA, Master(;ard and
be referred to qualified ser-
to service their
can have
system
provides access
parts... and all
needed
(;E
gener~y
s..,,
. . . .
!..... .s,,” .,... ,.., .,7””... -.,.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
fir
Customers With
.
Special Needs...
8b062&2000
Upon request,
c(mtr{)ls for a variety :tIld
a
brochure 10
harrier-free kitchen fi)r persons with
Iimiteci
mobility. T() obtain these item
free
of’cbarge, call 800.626.2000.
(;onsumers with impaired hearing
01
speech who have access to a TDD
01-
a
cc~rlventional
call
800-TDD-(;EAC” (800-833-4322)
to request infi)rrnation or service.
(1E
will provide Brain
of’(;E
appliance
assist in planning
teletypewriter may
i
Page 16
YOUR GE ROOM AIR CONDITIONER
WARRANTY
Save
proof of original purchase date such as your sales slip or cancel led check to establish warranty period.
II
WHAT IS COVERED
WHAT IS NOT COVERED
Service trips to your home to
teach you how to use the product.
Read your Use and Care material.
If you then have any questions
about operating the product please contact your dealer or our Consumer Affairs office at the address below, or call, toll free:
GE Answer Center[”
800.626.2000 consumer information service
)
FULL ONE-YEAR WARRANTY
For one year from date of original purchase, we will provide, free of charge, parts and service labor in your home to repair or replace
any part of the room air conditioner
of a manufacturing defect. FULL-FIVE YEAR WARRANTY For five years from the date of
original purchase, we will provide, free of charge, parts and service labor in your
replace any part
that fails because
home to repair or
of
the
sea/ed
refrigerating system (the
compressor, condenser, evaporator and all connecting tubing) that fails because of a manufacturing defect.
For each of the above warranties:
Transportation expense to and from a
sewice shop and shop semice
free of charge.
labor if required will be
Improper installation.
If you have an installation
problem, or if the air conditioner is of improper cooling capacity for the intended use, contact your dealer or installer. You are responsible for providing adequate electrical connecting facilities.
Replacement of house fuses or
resetting of circuit breakers.
I
n commercial locations labor
necessary to move the unit to a location where it is accessible for service by an individual technician.
This warranty is extended to the original purchaser and any succeeding purchased for use in the 48 mainland states, Hawaii and Washington, warranty is the same except that it is LIMITED because you must pay to ship the product to the service shop or for the service technician’s travel costs to your home.
All warranty service will be provided by our Factory Centers or by our authorized Customer normal working hours.
Look in the White or Yellow Pages of your telephone directory for GENERAL ELECTRIC COMPANY, GENERAL ELECTRIC FACTORY SERVICE, GENERAL FACTORY SERVICE or GENERAL ELECTRIC CUSTOMER SERVICE.
Failure of the product resulting
from modifications to the product or due to unreasonable use including failure to provide reasonable and necessary maintenance.
Failure due to corrosion on
owner for products
D.C. In Alaska the
Sewice
Care’) servicers during
ELECTRIC-HOTPOINT
CAREF’
models not corrosion-protected.
Damage to product caused
by improper power supply voltage, accident, fire, floods or acts of God.
WARRANTOR IS NOT RESPONSIBLE FOR CONSEQUENTIAL DAMAGES.
I
I
Pub
11-91
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion
may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state
To know what your legal rights are in your state, consult your local or state consumer affairs office or your state’s Attorney General.
Warrantor: General Electric Company
If further help is needed concerning this warranty, write:
Manager—Consumer Affairs, GE Appliances, Louisville, KY 40225
No.
49-7259
CG
I
I
AMV(
Loading...