GE AME06, AME08 Use and Care Manual

Page 1
Use and Care & Installation Guide
Contents
Adapter Plug Air Direction
Air Filter Grille & Cabinet
Outdoor Coil
Consumer Services Control Settings
Electrical Requirements
EnerW EnerW-Saving Tips
Extension Cords Freezing Up
Saver
Stitch
4,5
15
Room
3 5
2 6
6 6
6
3 5
7 3
4
Air
Conditioner
Grounding Installation Instructions
Model Problem Solver
Safety Instructions User Maintenance Instructions 6
Warranty
GE Answer Center
800.626.2000
Models
and Serial Numbers 2, 6
m
AME06
8-14
Back Cover
AME08
GE Appliances
3
7
2
Page 2
Help us help you...
WPORTANT
Uyou
need
sertice
Before using your air conditioner, read this book carefully.
It is intended to help you operate
and maintain your new conditioner properly.
Keep it handy
for
air
answers to
your
questions.
If you
don’t understand something or need more help, write (include your phone number):
Consumer Affairs GE Appliances Appliance Park Louisville, KY 40225
Write down the model and
serial numbers.
You’ll find them on a label behind the front grille on the left-hand side of the air discharge duct.
These numbers Consumer Product Ownership Registration Card that came with your air conditioner. Before sending in this card, please write these numbers here:
Model Number
are
also on the
SAFETY
~STRUCTIONS
Read all instructions before
this
using
When using this appliance, exercise basic safety precautions, including the following:
Use this appliance only for its
intended purpose
in this Use and Care Guide.
This air conditioner must be properly installed in accordance with the Installation Instructions
before it is used. See
instructions.
Never unplug your air
conditioner by pulling on the power cord.
firmly and pull straight out from the receptacle.
Repair or replace immediately all electric service cords that have become frayed or otherwise damaged.
shows cracks or abrasion damage along its length or at either the plug or connector end.
appliance.
always
as described
grounding
Always grip plug
Do not use a cord that
To obtain service, see the Consumer Services page in the back of this book.
We’re proud want you to be pleased. If for some reason you are not happy with the service you receive, here are three steps to
FIRST, contact the people who serviced your appliance. Explain why you are not pleased. In most cases, this will solve the problem.
NEXT, if you are still not pleased, write all the details—including your phone number—to:
Manager, Consumer Relations GE Appliances Appliance Park Louisville, KY 40225
FINALLY, if your problem is still
not resolved, write:
Major Appliance Consumer
Action Panel 20 North Chicago, IL 60606
of
our service and
follow for
Wacker
further
Drive
help.
Serial Number
Use these numbers in any correspondence or service calls concerning your air conditioner.
If you received a damaged
air conditioner...
Immediately contact the dealer (or builder) that sold you the conditioner.
air
Save time and money. Before you request service...
Check the Problem Solver section of this guide. It lists causes of minor operating problems that you can correct yourself.
2
Unplug your air conditioner
before making any repairs.
Note: We strongly recommend that any servicing be performed by a qualified individual.
For your safety..
.do
not store or use combustible materials, gasoline or other flammable vapors or liquids in the vicinity of this or any other appliance.
SAVE THESE
~STRUCTIONS
Page 3
Electrical
Safety—IMPORTANT...please
Read Carefully.
How to connect electricity
For personal safety, this ~ppliance must be properly grounded.
Electrical requirements
115-voIt models require a
volt
a.c., 60 hz
protected with a 15 amp time delay fuse or circuit breaker.
The power cord on these a three-prong (grounding) plug that mates with a standard three-prong (grounding) wall outlet (Fig. I ) to minimize the possibility of electric shock hazard from these appliances.
PREFERRED , METHOD
Fig. 1
Where a standard two-prong wall outlet is encountered, it is your personal responsibility and obligation to have it replaced with a properly grounded three-prong wall outlet.
grounded outlet
DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR REMOVE THE THIRD (GROUND) PRONG FROM THE POWER CORD.
230/208-volt models
own single branch circuit 230/208-volt time delay fuse or-circuit breaker. This is recommended for best performance and overloading house wiring circuits,
which
could
hazard from overheating wires. The power cord on these models
has a 230/208-volt perpendicular, tandem or large tandem type plug
a.c.,
protected with a
to
prevent
cause a possible fire
115/120-
models
m~ N’
<,
~
INSURE PROPER GROUND EXISTS BEFORE USE
require their
supplyin~
has
Q
that mates respectively with a 230/208-volt perpendicular, tandem or large tandem type outlet. These available at most hardware stores.
230/208-VOLT
tv~es
of outlets are
. .
MATCHING
wall
TEMPORARY METHOD
(ADAPTER PLUGS NOT P
P
Fig. 2
‘PERPENDICULAR TYPE WALL OUTLET
LINE CORD PLUG
REQUIRES 20 AMP TIME DELAY FUSE
OR CIRCUIT BREAKER PROTECTION
230/208-VOLT
MATCHING
TANDEM TYPE WALL OUTLET
LINE CORD PLUG
REQUIRES 15 AMP TIME DELAY FUSE
OR CIRCUIT BREAKER PROTECTION
n-o
Q
mm
Qo
. . . ,.
230/208-VOLT
LARGE TANDEM TYPE WALL
LINE CORD PLUG
REQUIRES 30 AMP TIME DELAY FUSE
OR CIRCUIT BREAKER PROTECTION
Whether your air conditioner is a 115-volt or a 230/208-volt unit, it is important to have the wall outlet and circuit checked by a qualified electrician if there is any doubt as to whether a proper ground exists.
Use of adapter plug
(115-volt models only)
Because of potential safety hazards under certain conditions, we
strongly recommend against use of an adapter plug. However, if
you
still
elect to use an adapter,
where local codes permit, a TEMPORARY CONNECTION may be made to a properly grounded two-prong wall outlet by use of a
listed adapter (Fig. 2) available most local hardware stores.
MATCHING
OUTLE1
UL
at
The larger slot in the adapter must be
aligned
wall
;utlet
in the connection of the power cord. CAUTION: Attaching the adapter
ground terminal to wall outlet cover screw does not ground the appliance unless cover screw is metal, and not insulated, and wall outlet is grounded through house wiring. You should have the circuit checked by a qualified electrician to make sure the outlet is properly grounded.
When disconnecting the power cord from the adapter, always
hold the adapter with one hand. If this is not done, the adapter ground terminal is very likely to break with repeated use.
Should the adapter ground terminal break, DO NOT USE the appliance until a proper ground has again been established.
Use of extension cords
Because of potential safety hazards under certain conditions, we strongly recommend against
the use of an extension cord.
However, if you still elect to use an extension cord, it is absolutely necessary that it be a UL listed 3-wire grounding type appliance extension cord carrying rating of the cord in amperes be equal to or greater than the branch circuit size shown on the rating nameplate of the appliance.
BEFORE USE
with the
to provide
larger
and
that the current
o
slot in the
~roper poltity
3
Page 4
Operating Your Air Conditioner Controls
LOW COOL
\\\
\\\
,.’
=
a
SELECTOR
,\\\lloll///,,
-.
///,.
~MoEoDL
//,
“,
,,
“-
;
HIGH
COOL
FAN
ONLY ●\’
OFF ,
Selector Switch
OFF
turns
air
conditioner off.
FAN ONLY
operation without cooling.
For
FAN ONLY
Energy Saver Switch must
in NORM
LOW COOL permits cooling with low fan speed operation.
MED COOL permits cooling with
medium fan speed operation. HIGH COOL permits cooling
with high
permits
po.~ition.”
fan
speed operation.
fan
op(~ration,”
speed
b(~
THERMOSTAT
1
2C
:8
51 6R
7 8 9
I
10
1
Thermostat Control
When you move the Thermostat Control to the desired setting, the thermostat will automatically control the temperature of the indoor air. The higher the number selected, the cooler the indoor air will become.
TIMER
HOUR
o
MANUAL
Timer Control
When you turn the Timer Control to the MANUAL setting, the air conditioner starts immediately and operates continuously if the Selector Switch is at any setting other than OFF.
When used with the Delay
SttiStop
Control turns the air conditioner on or off at preset times.
To delay the start of the air conditioner anywhere from
1 to 12 hours.
1.
Set the Timer Control for the number of hours you want to delay the start of the air conditioning operation.
Switch, the Timer
Freezing up
4
Outside air temperature dropping
If you notice that your air conditioner is not cooling as it should, it may be
that ice has formed on the cooling coils. The ice blocks air flow and stops the unit from cooling the room. This “freezing up” is a temporary condition that most often occurs at night when the Thermostat is set at a higher number and the Selector is set on LO COOL.
To correct the condition, set the Selector at HI FAN or HI COOL and move the Thermostat to the warmest setting.
2. Set the Delay
SttiStop
Switch at
DELAY START.
3. Turn the Selector Switch to the desired setting.
To stop the air conditioning operation from 1 to 12 hours later:
1.
Set the Timer Control for the number of hours you want the air conditioner to operate before shutting off automatically.
2. Set the Delay
SttiStop
Switch at
DELAY STOP.
3. Turn the Selector Switch to the desired setting.
Page 5
Energy Saver Fan Cycle Switch
NORM
m
ENERGY SAVER
This switch controls the operation.
NORM setting allows continuous function, circulating the compressor has cycled off thermostat setting has been reached. This setting is recommended maximum comfort.
SAVE setting lets the
and
off with the compressor during cooling. The fan stops when the thermostat setting is satisfied. This setting results in longer off time
and
wider variations of room
temperature and humidity. This setting is normally used when the room is unoccupied.
OPEN VENT CLOSE
(ON THE LOWER RIGHT SIDE OF THE DISCHARGE GRILLE)
I
Ilh
,!
I
I
fan
air
even when
fan
cycle on
SAVE
for
~nd
fan
the
Ventilation Control
When you move the Ventilation Control to CLOSE, the vent door is closed and only the air inside the room will be circulated and conditioned. Moving the control to OPEN opens the vent door, allowing a small amount of indoor air to be exhausted from the room.
However, cooling effectiveness is reduced when this control is set at OPEN, so we suggest you don’t keep it there hot, humid weather.
Iong+specially
in
For normal cooling
1.
Set the Selector Switch at HIGH
COOL.
2. Set the Thermostat Control at the desired number (usually 5-7 is a good starting position). temperature is not satisfactory after a reasonable time, set the Thermostat Control at a higher number lower number for a warmer room.
3. Set the Energy Saver Switch at
NORM position operation or at SAVE position to automatically cycle the fan on and
off with the compressor.
4. Set the Ventilation Control at CLOSE except for brief periods when you want to exhaust room air to the outside.
for
a cooler room or at a
for
For maximum cooling
1. Set the Selector Switch at
HIGH COOL.
2. Turn the Thermostat Control to
10.
3. Set the Ventilation Control CLOSE.
4. Set the Energy Saver Switch at the NORM position.
For quieter operation
1.
I
Set the Selector Switch at LOW
COOL position.
2. Slide the Thermostat Control to the desired number.
3. Set the Ventilation Control at CLOSE.
4. Set the Energy Saver Switch at NORM position.
Note: When the Energy Saver Switch is at the SAVE position, changes in the sound level may be more noticeable than when it’s at the NORM position.
If
room
continuous
at
fan
For nighttime operation
During the cooler evening hours, recommend that you set the Switch at LOW COOL for quieter operation and the Thermostat Control at mid-range (5 or 6). Set the Ventilation Control at CLOSE and the Energy Saver Switch NORM or SAVE position.
W(
Selecto
tit
For extreme temperatures
For greatest economy and best performance, we suggest you set the Selector Switch COOL in extremely hot weather.
at
HIGH
To adjust air direction
Up and
The up-and-down air direction louvers are controlled by fingertip pressure on the louvers. They regulate air discharge upward, downward, or straight out.
Side to side
Two separate banks of side-to-side air direction louvers have separate tabs to let you direct discharged air to the right, to the left, or straight out.
down
UP-AND-DOWN
AIR DIRECTION
Page 6
Care and Cleating
USER MAINTENANCE INSTRUCTIONS
Turn
air
conditioner off
and
remove plug from wall outlet before cleaning.
Grille & Cabinet
Wipe front grille with a lightly dampened with mild
dishwashing detergent. Wash
cabinet with mild soap or detergent
and
lukewarm water.
clean
cloth
liquid
Outdoor Coil
This
coil on
the outdoor side
of the unit
periodically and cleaned if clogged with dirt or soot from the atmosphere. soiled, it may need to be steam cleaned, through your GE service outlet,
should
be checked
If
extremely
a
service available
Front Grille
Remove the front window sill prevents removal the air filter or if you need to read the model and serial numbers.
To remove the grille: Step 1:
that
Remove and save the screw
holds
the grille to the chassis.
Step 2: Press inward on the lower right side of the cabinet until the
tab is clear
of
grille to come toward you slightly. Step 3: Repeat this process
lower left side.
D{)
not
pull
vOU
more than 3
to the top 2
OC’C:UK
Step 4: Grasp the grille’s lower right and left corner and carefully
lift straight upward to disengage the 2 top tabs from their slots in the cabinet front edge.
grille
if the
of
the slot and allow the
for
the
the bottom”
tub.v (?j’the
edge toward
inc”he.s or
grille
damage
mu>
CABINET
Air Filter
The air should be washed days or as often as it needs cleaning.
To remove the filter,
on the filter and pull downward. the window sill blocks access to the
air
front grille.
Vacuum the filter on the dusty side
to remove light dust. Wash the
filter, cleaner side up, under flowing water to wash out accumulated dust filter is very dirty, use a mild household detergent in the wash water. Let the before replacing it.
When replacing the filter, be sure the word FRONT is facing you as you slide the filter back into place.
filter
behind the inlet grille
at
least every
grasp
filter
you must first remove the
and
lint. If the
filter
dry thoroughly
30
the tab
If
gently
6
o e’
To attach the grille:
The grille is attached on the front
of the cabinet by four tabs and a
screw. Step 1: Lower the 2 top tabs of the
grille
into the
slots
in the cabinet
top.
Step 2: Carefully push the sides of the grille over the cabinet sides until the side tabs lock into the slots.
D{) not strike or,fi)rcibl> hit the grille or damage to OL’C’UK
th(~ t(~b.~
will
Step 3: Replace the screw that holds the
grille
to the chassis.
Page 7
Ener~-Saving
Tips
—a
Questions
Keep the
For most efficient cooling,
air
filter
clean.
keep the ventilation control in the CLOSE position
except
when you want to exhaust air, smoke or odors from the room.
Don t let the room
get
too hot. Whenever possible, turn the unit on before the room heats up. When heat is “stored up” in
walls,
furniture, rugs and draperies, your air conditioner takes longer to produce the desired comfort condition.
Keep windows
closed. Cool, dry
and
air
doors escapes
when they’re open.
Keep furnace
floor
registers and cold air returns closed. Cold air can easily escape through them.
Don’t let drapes or furniture block
the
top
or front of unit and restrict
air flow when it is operating.
It’s best to operate your air conditioner at high speed during extremely hot weather.
Keep the outdoor condenser coil clean.
Turn air conditioner off before vacations or extended absences
from
home.
‘~:
Use This Problem Solver
PROBLEM
AIR
CONDITIONER
DOES NOT OPERATE
AIR CONDITIONER “DOES NOT COOL AS IT
SHOULD’7
OPERATING SOUNDS
POSSIBLE CAUSE
Not plugged in. Plug may have been bumped
loose by vacuum cleaner or furniture.
If plugged in, fuse could have blown or
circuit breaker may have tripped.
Curtain, blinds or furniture blocking the top or
the front of the air conditioner will restrict air
c
Thermostat Control may not be set high enough.
tlow.
Move the knob to a higher number. Highest
setting should provide maximum cooling. When Energy Saver Switch is set at SAVE, temperature
range in room will vary more.
Air filter dirty, should be cleaned at least
every 30 days.
Room may have been very hot when air conditioner was first turned on. Allow time for it to cool down.
Q
Cold air may be escaping through open
furnace floor registers and cold air returns.
Ventilation control may be set at OPEN position,
allowing hot outside air to enter
Cooling coils have iced up. To melt ice, move
the
room.
the Selector Switch to FAN ONLY and the Thermostat Control to a lower number.
Thermostat click, a metallic sound, may be heard
when compressor cycles on and off. This is normal.
Fan runs continuously when Selector Switch
is in COOL or FAN position. This is normal. When Energy Saver Switch is set at SAVE, fan cycles on and off with compressor.
WATER DRIPPING OUTSIDE
WATER DRIPPING INSIDE
WATER IN BASE PAN (ON OUTDOOR SIDE)
Excess water may overflow in extremely hot
and humid weather. This is normal.
Air conditioner must be installed level or tilted
slightly to the outside for proper water disposal.
This is normal for a short period in areas with
little humidity; normal for a longer period in very humid areas. Moisture removed from indoor air drains to rear of cabinet where it is picked up by a fan and thrown against the outdoor condenser coil.
If you need more help... call, toll free: GE Answer Center
(
800.626.2000 consumer information service
7
Page 8
I
INSTALLATION INSTRUCTIONS
I
BEFORE YOU BEGIN
Read these instructions completely and carefully.
lMPORTANT—Observe
and ordinances.
lNSTALLER—Be
instructions with the consumer. CONSUMER–Keep these instructions for
future reference.
sure to leave these
all governing codes
ELECTRICAL REQUIREMENTS
FOR PERSONAL SAFETY:
THIS APPLIANCE MUST BE PROPERLY
GROUNDED. See grounding instructions.
DO NOT, UNDER ANY CIRCUMSTANCES,
CUT OR REMOVE THE THIRD GROUNDING PRONG FROM THE POWER CORD.
WE RECOMMEND THAT YOU DO NOT USE
AN EXTENSION CORD OR AN ADAPTER PLUG WITH THIS APPLIANCE.
DO NOT CHANGE THE PLUG ON THE
POWER CORD OF THIS APPLIANCE.
FOLLOW NATIONAL ELECTRICAL CODES
OR LOCAL CODES AND ORDINANCES.
WINDOW REQUIREMENTS
Standard double-hung window with actual
opening width of 25“ to 40”.
Clear vertical opening of 14“ minimum from
bottom of sash to stool.
Install the air conditioner in a window where
there will be enough clearance around the cabinet to allow ample circulation of air through the unit.
//’
I
t
.
Note: All supporting parts should be secured to
firm wood, masonry or metal.
25” tO 40”
14“
min.
*
V1208V
115V
15 AMP circuit 20 AMP circuit
“parallel” type
II
o
If the electrical supply provided does not meet
the above
Aluminum house wiring may pose special
problems—consult a qualified electrician.
This unit requires a separate circuit serving only
this appliance.
specifications,
230
“perpendicular<’ type
1-
o
230V/208V 230V/208V
15 AMP
ctrcuit
“tandem” type “tandem” type
call a licensed electrician.
30 AMP
c!rcuit
8
Page 9
-DOW
INSTALLATION
TOOLS NEEDED
Phillips head screwdriver
Blade-type screwdriver
Sharp knife or razor blade
Rule or tape measure
Pencil
Type A
screw
Type
scre
Level
Box wrench
SCREWS FURNISHED
Type
Type
Qty-3
A
B
Qty-2
(see samples)
Type C
T
Qty-4
Type D
+
Qty-6
t
Sealer (1
1/2
Type A
screw
Right
dow filler
panel
oz.)
(continued next page)
9
Page 10
I
WINDOW INSTALLATION
~
REMOVEFRONTGRILLE
See Front Grille section.
~
PREPARE CHASSIS.
1. Remove chassis locking bracket and chassis locking screw with a Phillips head screwdriver.
(Save for reuse.)
I
w.
PREPARE CABINED
1. Install top mounting rail onto top of cabinet
with 3 Type D screws.
I
Chassis locking
scre
(cont,nue~,
+
Top mounting rail
Room side
+
+
~
Type D screw
~~abine~~op
1~
Chassis locking bracket
2. Remove ground screw and ground wire.
(Save for reuse.)
Ground screw
Ground wire
Type D screw
Type D screw
2. Install bottom sill channel onto cabinet by
inserting notches on channel into slots located on bottom of cabinet and securing with 3 Type D screws.
o
Ill II
3. Remove chassis from cabinet using the base pan
as a handle.
10
Page 11
EArAcHwJNDOwFJllERPANELS
1. Slide left window filler panel into top and bottom
mounting rails.
2. Slide retainer panel into window filler panel and attach to cabinet with 2 Type C screws.
3. Repeat for right side.
5. Secure top mounting rail with two Type B screws.
Ier
a
Window — filler panel
o
Top mounting rail
L
Bottom mounting rail
Retainer panel
, JNSmLL
1. Cut sealing ribbon to window width and stick it
to bottom of the lower window sash.
2. Measure and mark center of window sill to establish mounting position of cabinet.
3. Install cabinet into opening and center on line marked on window
you and lower window sash b rail.
CABJNETJNWJNDO~
sill;
Put
to]
]f
cabinet toward
lind top mounting
JNSTALL
Cut foam sash gasket to window width and stuff between top of lower sash and glass panes of upper sash. Make sure foam gasket is flush with top of lower sash.
SASH
GASKEZ
— Sealing
ribbon (ADHESIVE SIDE)
Center line
4. Extend and secure left and right window filler
panels to window sash with Type A screws, one on each side.
JNS~LL SASH LOCK
Install sash locking bracket using Type A screws.
Type A screw
(continued next page)
11
Page 12
WINDOW INSTALLATION (Continued)
INSML[
1.
Slide chassis into cabinet. (Make sure tubing on
unit is not touching wail case.)
2. Lock chassis into cabinet by reinstalling chassis locking bracket and chassis locking screw removed in Step 2.
3. Reconnect ground wire removed in Step 2 to chassis.
4. Remove enough line cord to reach the wall receptacle.
CHASSIS IN CABINED
Chassis locking bracket
CHECKFOR
Seal small openings around cabinet with gum-type
sealer, provided.
/NS~LL
See Front Grille section.
AIR LEAKS.
FRONTGRILLE
12
Page 13
THROUGH-THE-WALL INSTALLATION
THE CABINET MAY BE INSTALLED THROUGH THE WALL IN BOTH EXISTING BUILDINGS AND NEW CONSTRUCTION.
lMPOR~NT
Any
side
louvers must project on the
side of the wall.
The room side of the cabinet must project into
the room at least 1“ from the finished wall.
The cabinet must be installed level from side to
side and with a 3/8” tilt from front to rear.
oudoor
PREPARE WALL OPENING.
Determine size of opening. Measure width and
1.
height of cabinet and add 1/8” to each dimension.
TOOLS REQUIRED
Phillips head screwdriver
Blade-type screwdriver
Magnetic stud finder (optional)
Tin snips
Handsaw
Level
Chisel
Concrete saw (if installing through a masonry wall)
Hammer
Caulking gun
Tape measure
ADDITIONAL MATERIALS NEEDED
(obtain locally)
12 #10 wood screws, 1“ long
1 tube high grade caulking compound
Wooden framing studs
Lintel, if required, to support bricks or blocks
above opening
Flashing, alum inure or galvanized steel
2. Choose the wall opening location. Be sure a power receptacle
3.
Make the opening. Frame it to support the
is (or will be) installed nearby.
weight of the air conditioner. Add metal flashing over bottom of frame opening
and 1“ up on sides to reduce the possibility of moisture entering the area between the inner and outer wall. The flashing lip should be 1“ wide and
bent down
PREPARE THE CABINED
45!
See the illustration, page 14.
1. Remove chassis from cabinet. See Step 2 of
Window Installation.
2. With caulking compound or electrical tape, seal all holes provided in the cabinet for window installation hardware not used in this installation.
lNS~LL
CABINETIN WALL.
1. Place cabinet in wall opening.
2. Secure cabinet bottom rail to wooden frame with two 1“ long #1 O wood screws.
.<. :=
.~.~
+= s-’<<~-
**-
QS
+W
+
?
-\
+
(continued next page)
13
Page 14
THROUGH-THE-WALL INSTALLATION
INSMIL
3. Secure cabinet sides to wooden frame with six
1“ long #1 O wood screws and secure cabinet top
to frame with four 1“ long #1 O wood screws.
CABINETIN WALL (continued).
——
——
Holes for #10 1“ Long
Wood Screws
9
I
(cont,nue~,
ster
Line
Trim Molding (if desired)
INSIDE
Drill holes in cabinet sides and top, if necessary for proper installation. If frame is oversize, use shims to prevent cabinet distortion.
4.
Caulk all four cabinet to prevent moisture from getting through to the interior wall. Use of flashing (a piece of aluminum or galvanized steel available at most hardware stores) will further prevent moisture
from getting into interior walls.
5. Install wood trim molding (obtained locally) around
4
In
Lift the chassis and carefully slide it into cabinet. Do not push on controls or finned coils. Make sure chassis is firmly seated toward rear of cabinet.
roomside
SLIDE CHASSIS INTO
sides on the outdoor
projection of cabinet, if desired.
side of
CABINEZ
——
Caulking
Flashing Lip
Flashing
‘]
\
_——---——
.
— . .
. . .
.—.
—..
.
:.
T
J j
~91/
I
,;‘
--
1
. .
~.
-
(
I
/
i
‘:,1
~
I
:
:;
In
5 lNS~LL
See Step 8 of Window Installation.
CHASSIS IN CABINED
I
6 lNS~LL
In
See Care and Cleaning section.
I
14
FILTER AND
GRILLE
Page 15
Wdll
Be There
With the purchase of your new GE appliance, receive the
assurance that if vou ever need information or assistance from GE,
In-Home Repair Service
80ME4ARES (80W32-2737)
A
GE
consumer service
will
provide expert rep:iit-
scheduled at
fi)r you. c{)mpany-opcr;itcd you service your
c(mvenience weekdays, days).
know your s()
most repairs
one
visit.
wdll
b< there. All you have to do is call–toll-free!
professional”
service,
a time
that’s
M;iny (;E (;ousumer
loc~~tions offer
tod:~y
or
tomorrow,”
(7:()()
a.m. to
{1:()() ;~.m.
Our f’;t(:tory-tr~iine[i
~~ppliance
to 2:00 p.m. Satur-
inside and
c~m
be
h~mdlecl
convenient
Setvice
or :it
7:()()
p.m.
tech nici:ms
out-
in just
Service Contracts
80&626-2224
YOL]
c:m have the
(;E
(;orlsumer Service will still be
tbcrc af’tcr­chase;~ t’imty ii subslzmti:Ll ye2Lr contr ’;~ct, yoL1’t-e :issL~red
service at today’s prices.
(;E corrt.ract while yoLlr war-
is
slill
secLue
your
w:u-rimty expit-es.
in
cf~k>ct
and
discount. With:1
fkeling
yoL]’]1
receive
rr]ul Liple-
of
[.ll~L[
Put-
’filtLlr”e
GEAnswer Centera
80~6262000
help.
YOLlr- c;d-iuld yoLlr
will be answered
courteoLlsly.”
time. (;F.
open 24
Telecommunication Detice for the Deaf
Arrswet (;enter”
hoLu-s:~ d~~y,
promptly
And you
quest.iorl-
imd
c~tn c~dl ~uly
selvice is
7
d~~ys a
week.
Parts
andAccessories
80@626-2002
Individuds ow
appliances c:m parts
theit-
The
(“;E p:~rts to river (;errLline wat-rauted.
I)iscover cards are accepted.
User maintenance instructions contained in this booklet cover proce­dures intended to be performed by any user. Other servicing
shotid
vice personnel. Caution must be exercised, since improper servicing may cause unsafe operation.
qu~fied
or accessories
home, free of ’shipping
system provides
47,000” parts...~md all (;E
Renewal Parts are fully
VISA,
be referred to qualified ser-
to service their
h:~ve
rrecdcd
sent
directly
Master(”;ard
generdy
ch~irge!
to
:~ccess
and
S. CT,
...,0 ..6.,”.,...,..,.!,..,..
,,
...”.....,.......=....,=.
fir
Customers With
ONA.A
.“.,.
..
Special Needs...
Ur(~rr reqLlest, (JE
controls” :md ii
btirr’iel--fiee kitchen fi)r persons with
Iirnited fi-ee of’ch:ir-ge, c;dl
or” sreech or :i
C2L11800-TDD-(;F”A(:” (800
10
for:1
btocllLlt-e
tnobilily.
(lorlsumers with
who
corrven[i( )rr:ll
request
information”
will rrovide
Y:u-iety
of’(;kl
to
;tssisl
in
‘lo
obt;iin these items,
800.(
j2(j.2000.
irrlp:Lir-ed he~u-iug
h;ive
:lccess to iL TDD
[eletyrewriter
or service.
Br;iillc’
;iprli:mccs,
p12Lrlrlirl<<J ;i
rniiy
-83:;
-4:322)”
.,,,.,
Page 16
YOUR GE ROOM AIR CONDITIONER
WARRANTY
Save proof of original purchase date such as your sales slip or cancel led check to establish warranty period.
I
WHAT IS COVERED
WHAT IS NOT COVERED
Service trips to your home to
teach you how to use the product.
Read your Use and Care material.
If you then have any questions about operating the product please contact your dealer or our Consumer Affairs office at the address below, or call, toll free:
GE Answer
800.626.2000 consumer information service
Center@)
FULL ONE-YEAR WARRANTY
For one year from date of original purchase, we will provide, free of charge, parts and service labor in your home to repair or replace
any part of
conditioner
of a manufacturing defect.
the
room air
that fails because
FULL-FIVE YEAR WARRANTY
For five years from the date of
original purchase, we will provide, free of charge,
pafls and service
labor in your home to repair or replace any part of the
refrigerating system
compressor, condenser, evaporator and all connecting tubing) that fails because of a manufacturing defect.
sealed
(the
For each of the above warranties:
Transpotiation expense to and from
a service shop and
shop sewice labor if required will be free of charge.
Improper installation.
If you have an installation
problem, or if the air conditioner is of improper cooling capacity for the intended use, contact your dealer or installer. You are responsible for providing adequate electrical connecting facilities.
Replacement of house fuses or
resetting of circuit breakers.
In commercial locations labor
necessary to move the unit to a location where it is accessible
for
service by an individual technician.
This warranty is extended to the original purchaser and any succeeding owner for products purchased for use in the 48 mainland states, Hawaii and Washington, warranty is the same except that it is LIMITED because you must pay to ship the product to the service shop
or for the service technician’s
D.C. In Alaska the
travel costs to your home.
All
warranty service will be
provided by our Factory Service
Centers or by our authorized Customer normal working hours.
Look in the White or Yellow Pages
of your telephone directory for
GENERAL ELECTRIC COMPANY, GENERAL ELECTRIC FACTORY SERVICE, GENERAL FACTORY SERVICE or GENERAL ELECTRIC CUSTOMER
SERVICE.
Failure of the product resulting
Care” servicers during
ELECTRIC-HOTPOINT
CARE”
from modifications to the product or due to unreasonable use including failure to provide reasonable and
necessary maintenance.
Failure due to corrosion on
models not corrosion-protected.
Damage to product caused
by improper power supply voltage, accident, fire, floods or acts of God.
WARRANTOR IS NOT
RESPONSIBLE FOR
CONSEQUENTIAL DAMAGES.
I
Pub
11-91
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion
may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which
To know what your legal rights are in your state, consult your local or state consumer affairs office or your state’s Attorney General.
vay
from state to state.
Warrantor: General Electric Company
If further help is needed concerning this warranty, write:
Manager—Consumer Affairs, GE Appliances, Louisville, KY 40225
No.
49-7260
CG
I
AME06 AMEO
Loading...