GE AEW08LSQ1, AEW08FMG1, AEW06LML1, AEW06LMG1, AEW05LMS2 Owner’s Manual

...

ge.com

Safety Instructions . ............ 9, 3

Operating Instructions

Control I_lob Models ........... 6, 7

Touch Pad Models .............. 4, 5

Care and Cleaning

Air Filter ........................ 7

Outdoor Coils .................... 7

AET05 AEW05 AEW06 * AEwog *

Installation Instructions ....... 8-11

Troubleshooting Tips ........... 12

Normal Operating Sounds ........ 12

Consumer Support

Consumer Support ....... Back Cover

Ownership Registration fi)r

Customers in Canada only ..... 13, 14

Warranty for Customers

in Canada ...................... 16

Warranty fi)r Customers

in the U.S.A ..................... 15

*ENERGY STAR ® labeled product

Climadseur

La section fran_aise commence ?_la page 17

Acondicionador

de aire

La secci6n en espa'_,ol empieza en la pdgina 33

ENERGYSTAR

AS an ENERGY STAR® partnei; GE has

determined that this product meets the ENERGYSTAR®guidelines for

energy efficiency.

Writethe modelandserial numbershere:

Model # Serial #

Find these numbers on a label on the side of the air conditioneL

In Canada, contact us at: xs_s_<GEAppliances.ca

494606 12-08JR

IMPORTANTSAFETYINFORMATION. READALLINSTRUCTIONSBEFOREUSING.

WARNING!

For your safety, the information in this manual must be followed to minimize the risk of fire, electric shock or personal injury.

SAFETYPRECAUTIONS

}}Use this appliance only f_)r its intended }}

purpose as described in this Owner's Manual.

iii}i}i

This air conditioner must be properly installed in accordance xdth the Installation

Instructions befk)re it is used.

iii}i}}li_

Never unplug your air conditioner by pulling on the power cord. Always _-ip plug firmly and pull straight out flom the receptacle.

iii}i}}li_

Replace immediately 'allelectric ser\@e

iii}i}i

iii}i}}li_

cords that have become flayed or otherwise damaged. A damaged power supply cord must be replaced with a new power supply

cord obtained from the manufacturer and not repaired. Do not use a cord that shows

iii}i}}li_

cracks or abrasion damage along its len_h or at either the plug or connector end.

iiiH}}ii{_

Turn the unit OFFand unplug your air conditioner before cleaning.

GE does not support any ser\,icing of the air conditioner We strongly recommend that

you do not attempt to ser\,ice the air

conditioner yoursel£ For your sNety...do not store or use

combustible materials, gasoline or other

flammable vapors or liquids in the x,icinity

of this or any other appliance.

All air conditioners contain refligerants, which under federal law must be removed

prior to product disposal. If you are getting rid of an old product with refrigerants, check with the company handling disposal

about what to do.

If the receptacle does not match the plug, the receptacle must be changed out by a qualified electrician.

HOWTOCONNECTELECTRICITY

Do not, under any circumstances, cut or remove

the third (ground) prong from the power cord. For personal safety, this appliance must be properly grounded.

DONOT use an adapterplug with this appliance.

The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a standard 3-prong (grounding) wall outlet to minimize the possibility of electric shock hazard flom this appliance.

Power cord includes a current intermpmr dex,ice. A test and reset button is prox,ided on the plug case. The dex,ice should be tested on a periodic basis by first pressing the rESrbutton and then the RESErbutton while plugged into the outlet. If the rESrbutton does not trip or if the RESErbutmn will not stay engaged,

discontinue use of the air conditioner and contact a qualified ser\,ice technician.

Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly _ounded.

Where a 2-prong wall outlet is encounmred,

it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet.

The air conditioner should always be plugged into its own indix,idual electrical outlet which

has a voltage rating that matches the rating plate.

This prox,ides the best perfk_rmance and also prevents overloading house xdring circuits

which could cause a fire hazard flom overheated xdres.

See the Installation Instructions, Electrical Requirements section f_r specific electrical

connection requirements.

WARNING!

USEOFEXTENSIONCORDS--115-Voltmodelsonly

ge.com

Because of potential safety hazards under certain

conditions, we strongly recommend against the

use of an extension cord.

However, if you must use an extension cord, it is absolumly necessa U that it be a UL-listed, 14-gauge, 3:wire grounding-type appliance extension cord ha\,ing a _oundinDtype plug and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 125 vohs.

-4,CAUTION:

DO NOT use an extension cord with any of the 230/208 voltmodels.

READANDFOLLOWTHISSAFETYINFORMATIONCAREFULLY.

SAVETHESEINSTRUCTIONS

Aboutthe controlsontheair conditionermmodels with touchpads.

Features and appearance will van Lights next to the touch pads on the air conditioner control panel indicate the selected settings.

Light indicatesthe unit

Thedisplayalwaysshowsthe room temperatureexceptwhensettingthe

Settemperatureor the Delaytimer.

m High m Fan Only m, Ned am Energg Saver

i Low ! Cool

is inthe temperatureor delaytime Set mode.

Lightindicates the delaytimer is set.

Delay

O Delaytimer --

Decrease J

O an speed

Decrease

Temperature --

set hlcrease

and Decrease

Delaytimer Increase

Auto Fanon/off

Fanspeed Increase

Unit poweron/off

AirConditionerControls

Contro/s

O ower Pad

Turns air conditioner on _md off. _rhen turned on, tile display will show tile room

temperature.

0 Display

Shows tile room temperature or time remaining on the Del W fimeL Shows the Set

mmperature while setting the mmperature in

Coolor Energy Saver modes. The Set light will

mrn on while setting. NOTE:The display will change to show file

room temperature after settings have been made. To recall the Set mmpemmre, press the

TampIncrease • or Decrease • pads.

O empIncrease •/Decrease • Pads

Use to set temperature when in Coolor Energy Savermode. The Setlight will mrn on while

setting.

O Delay fimerlncrease • (+)/Decrease • (-)

Pads

Each touch of the Increase •/Decrease • pads on the unit or the Increase+/Decrease - pads on the remote control will set the delay

time when using the Delay1-24hrtimer (1_). The Setlight will mrn on while setting.

O an Speed Pads

Use to set the fan speed to LOW,Mad, High or Auto on the unit. NOTE: On the remote

control, use the fan speed Increase +/

Decrease - pads to set the fan speeds to LOW, Mad or High. Use the Auto pad to turn Auto

fan on.

Remote Control

O ode Pad

Use to set tl_eair conditioner to Cool,Energy

Saveror FanOnlymode. Delay Pads

Delay ON--When the air conditioner is of L it can be set to automatically come on in 1 to 24 hems at its previous mode and fan settings.

Delay OFF--When the air conditioner is on, it can be set to automatically mrn offin 1 to

24 hems.

How toset:

Press file Delay 1-24hr pad on the unit or die @_pad on file remora conuol. Each touch

of the Increase •/Decrease • pads on the unit or the Increase +/Decrease- pads on

tile remote control will set the timer in

1-hour intervals. The Set light will mrn on

while setting.

To review die remaining time on die Delay

1-24hrtime_; press the Delay 1-24hr pad on the

unit or the @ pad on the remote control. Use the Increase •/Decrease • pads on the unit

or the Increase +/Decrease-pads on the remote control to set a new time if desired.

Tocancel the timer, press tt_e Delay 1-24hr pad

until tile light on the Delay 1-24hr pad goes off:

Do Not Operate in Freezing Outdoor Conditions

This cool<rely air conditioner was not designed for fleezing outdoor conditions. It illust not be used in

fleezing outdoor conditions.

Remote Control

ge.com

To ensure proper operation, aim file remora conuol at the signal receiver on the air

condifioneL

Tile remote conuol signal has a range of up m 20 feet.

CoolMode

Use file Coolmode at Low,Med,Highor AutoFan Speedfor cooling. Use tile TemperatureIncrease• /

Decrease • pads to set tile desired temperature between 64°F and 86°F in 1°F increments.

An electronic fllemlostat is used to maintain file

room temperature. Tile compressor will cycle on and off to keep file room at file set level of comfort.

Set file themlostat at a lower number and file indoor air will become cooleL Set die fllelInostat at a higher

number and file indoor air will become wamleL

NOTE:If theairconditionerisoffandisthenturnedon

whilesettoa Coolsettingorif turnedfromafansetting toa Coolsetting,it maytakeapproximately3minutes

forthecompressorto startandcoolingtobegin.

Energy Saver Mode

Controls tile fan.

ON--The fan will cycle on and offwidl die compressor. This results in wider variations of room temperature and humidity. Normally used when tile room is unoccupied. NOTE: The fan may continue to run

forashort time after the compressorcycles off.

Make sure riDdling is between die air conditioner and the remora conuol that could block the

sigmal. Make sure batteries are flesh and instaUed

correctly _tsindicated on the remora conuol.

CoolingDescriptions

ForNormalCooling--Selectthe Coolmode and Highor Med fan with a middle set temperature.

ForMaximum Cooling--Select tile Cool mode and Highfan with a lower set temperature.

ForQuieterandNighttimeCooling--Selecttile

Cool mode and Low fan with a middle set

temperature.

OFF--The tim runs all tile time, while file compressor cycles on and off:

Fan Only Mode

Use the FanOnlyModeat Low,Medor Highfan

speed to provide air circulation and filtering

without cooling. Since fan-only settings do not

provide cooling, a Set mmperamre camlot be enmred. Tile room mmpemmre will appear

in tile displ W.

Auto Fan Speed

Set to Autofan speed for tile fan speed to

automatically set m tile speed needed m provide

optimum comfort settings wifll tile set temperature. If the room needs more cooling, the fan speed

will automatically incre_tse. If the room needs less

cooling, the fan speed will automatically decrease.

Power Outage Recovery Feature

In tile case of a power outage or interruption, tile unit will automatically restart in the settings last used after tile power is restored. If tile Delay 1-24hr

NOTE:AutoFanSpeedcannotbeusedwhenin the FanOnlyMode.

feature was set, it will resume countdown. You may need to set a new time if desired. 5

Aboutthecontrolsonthe air conditionermmodelswith controlknobs.

Features and appearance will var}4.

MODE

High •

Cool.

Cool

OFF

High

MODECONTROL

Contro/s

Mode Control

HighCool,Med Cooland LowCool

provide cooling with (liff_rent fan speeds. Fan settings provide Mr circulation and

filtering Mfllout cooling.

NOTE:If youmovethemodecontrolfroma cool settingtoOFFortoa fansetting,waitat least

3 minutesbeforeswitchingbacktoacoolsetting.

Coolest

TEMP

TEMPERATURECONTROL

TEMP Control

Tile TEMP control is used to maintain the room tempe_mre. Tile compressor will cycle

on and off"m keep tile room at tile same level of comfolt. _r]len you mrn the knob to a

higher numbe_; the indoor air will become cooleL Turn the knob m a lower number mid

tile indoor air will become warmeL

Cooling Descriptions ForNormal Cooling--Select HighCoolor Med Cool

with tile TEMPERATURE control at midpoint.

ForMaximum Cooling--Select High Coolwith tile TEMPERATURE control at the highest number available on your knob.

ForQuieterandNighttime Cooling--Select Low Coolwith tile TEMPERATURE control at

midpoint.

Additional important information.

Air Direction

Use die lever to adjust file air direction left and right only.

Careand cleaning ofthe air conditioner.

Grille and Case

Turn the air conditioner off and remove the plug To clean, use water and a mild detergent. Do not flom tile wall oudet before cleaning, use bleach or ab_sives.

Air Filter

The air filter behind the front grille should be checked and cleaned at least eve_T 30 days or

more often if necessary.

Toremove:

Push on one side of the filter edge and pull it out the other side.

ge.com

Glean tlle filter widl warm, soapy wateL Rinse and let the filter dry before replacing it. Do not clean

the filter in a dishwasheL

CAUTION:DoNoToperatetheair

conditionerwithouta filterbecausedirtandlintwillclog it andreduceperformance.

Outdoor Coils

The coils on the outdoor side of the air conditioner should be checked regularly: If flley are clogged

with dirt or soot, they may be professionally cleaned.

How to Insert the Batteries in the Remote Control

[-_ Remove the batte D, cover by sliding it

according to the arrow direction.

Insert new batteries, making sure that the (+) and (-) of battery are installed correcdy.

[-_ Reatmch the cover by sliding it back

into position.

NOTES:

Use 2 "AAA" (1.5 volt) alkaline batteries. Do not use rechargeable batm_ies.

Remove the batteIies flom the remora control if the sysmm is not going m be used for a long time.

ilnsta,,at,onnsttuct,onsIAirC°ndit'°nerl

In Canada, call 1.800.561.3344 or visit www.GEAppliances.ca

I[-_ Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com I

BEFORE YOU BEGIN

Read these instructions completely and carefully.

IMPORTANT - Savethese

instructions for local inspector's use.

• IMPORTANT - Observeall

governing codes and ordinances.

• Note to Installer- Be sure to leave these instructions with the Consumer.

• Note to Consumer- Keep these instructions for future reference.

• Skill level - Installation of this appliance requires basic mechanical skills.

• Completion time- Approximately 1 hour

• We recommend that two people install this product.

• Proper installation is the responsibility of the installer.

Product failure due to improper installation is not covered under the Warranty.

You MUST use all supplied parts and use proper installation procedures as described

in these instructions when installing this air conditioner.

- CAUTION:

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.

Do not change the plug on the power cord of this air conditioner.

Aluminum house wiring may present special problemsmconsult a qualified electrician.

TOOLS YOU WILL NEED

Phillips head screwdriver

Flat-blade screwdriver

(_ ELECTRICAL REQUIREMENTS

60-Hz grounded outlet protected with a

Some models require a 115/120-volt AC,

15-amp time-delay fuse or circuit breaker.

The 3-prong grounding plug minimizes the

possibility of electric shock hazard. If the wall

outlet you plan to use is only a 2-prong outlet,

it is your responsibility to have it replaced with

a properly grounded 3-prong wall outlet.

Some models require 230/208-volt AC,

protected with a time-delay fuse or circuit breaker. These models should be installed

on their own single branch circuit for best performance and to prevent

overloading house or apartment wiring circuits, which could cause a possible

fire hazard from overheating wires.

Pencil Ruler or tape measure

Level Scissors or knife

Power cord includes a current interrupter device. A test and reset button is provided on the plug case. The device should be tested on a periodic basis by first pressing the TEST button and then the RESET button while plugged into the outlet. If the TEST button does not trip or if the RESET button will not stay engaged,

discontinue use of the air conditioner and contact a qualified service technician.

PARTS INCLUDED

(Appearance may vary)

Top mou_

Air

conditioner

Installation Instructions

vv,_a_;_

Left

accordion

panel

Window

eal

Right

accordion

panel

- /

Top mo "_

seal strip

Type A (6) Type B (3) Type C (5) Window locking

bracket (1)

Installation instructions

[] WINDOW REQUIREMENTS

• These instructions are for a standard double-

hung window. You will need to modify them

for other types of windows.

• The air conditioner can be installed without the accordion panels if needed to fit in a

narrow window. See the window opening dimensions.

All supporting parts must be secured to firm wood, masonry or metal.

The electrical outlet must be within reach of the power cord.

Follow the dimensions in the table and illustration for your model.

Models A B

AET05, AEW05 13" min. 24 1/2"-38 1/8" AEW06, AEW08 13 5/8" min. 24 1/2"-38 1/8"

[ //J

B===8

< B

(With accordion panels)

-3

ATTACH THE TOP MOUNTING RAiL SEAL STRIP

Remove the backing from the top mounting rail seal strip and attach the seal strip to the bottom of the top mounting rail, along the front edge.

Top mounting rail

Remove backing

from seal strip

FRONTViEW

Topmounting rail

]

Seal strip

I_1STORM WINDOW REQUIREMENTS

A storm window frame will not allow the air conditioner to tilt toward the outside, and will

keep it from draining properly. To adjust for this, attach a piece of wood to

the sill. WOOD PIECES WIDTH: 2"

LENGTH: Long enough to fit inside the window frame.

THICKNESS: To determine the thickness, place a piece of wood on the sill to make it 1/2"

higher than the top of the storm window

frame or the vinyl frame. Attach securely with nails or screws provided

by the installer.

than storm window

frame

1/2" higher __r_°°d

Storm window

frame

1/2" higher

than vinyl frame

L (on some windows)

[] PREPARE THE AIR CONDITIONER

I_] Install the top mounting rail with 3 Type B

screws from the outside of the case,

Bottom mounting rail

[] Slide the left and right accordion panels

into the top and bottom mounting rails.

Top right

Top left

Installation Instructions

141PREPARE THE AIR CONDITIONER

(cont.)

[] Attach the accordion panels to the case

using 3 Type A screws on each side.

Top mounting rail

Accordion

panel

Type

screws

BACK

161INSTALL THE AIR CONDITIONER

IN THE WINDOW

[_] Place the air conditioner on the sill with

the bottom mounting rail against its back edge. Center it and close the window securely behind the top mounting rail. It should be level or slightly tilted to the outside. Use a level; about a 1/3 bubble

will be the correct case slant to the outside.

Type C screws

[] Extend the left and right accordion panels

to the vertical window sashes and attach, through the holes in the panels, with 4 Type C screws, as appropriate.

Bottom mounting rail

151PREPARE THE WINDOW

Cut the window sash seal to the proper

length. Peel off the backing and attach the

seal to the underside of the window sash.

m INSTALL SUPPORT BRACKET AND

FOAM TOP WINDOW GASKET

[] CAUTION:

To prevent broken glass

or damage to windows, on vinyl or other

similarly constructed windows, attach the

support bracket to the window side jam.

Attach the support bracket with one

Type C screw.

Cut the foam top window gasket to the window width.

Stuff the foam

[]

between the glass and the

window to prevent air and

insects from getting into the room.

NOTE: If the gasket supplied does not fit your window, obtain appropriate material locally to provide a proper installation seal.

Vinyl

Wood

TroubleshootingTips.

Possible Causes What ToDo

Airconditioner doesnotstart

Air conditioner does Airflow is restricted. • Make sure there are no curtains, blinds or fiuniture

not cool as it should blocking the flont of the air condifioneL

The air conditioner

is tmplugged. The fuse is blown/circuit

breaker is tripped. Power failure.

The current interrupter • Press the RESETbutton located on the power cord plug. device is tripped. • If tile RESETbutton will not stay engaged, discontinue

The temp control may • On models wifll touch pads: In tile Cool mode, press tile not be set correctly. Decrease • pad.

The air filter is dirty. • Glean tile filter at least every 30 days.

The room may have been hot. • When tile air conditioner is filst turned on, you need

• Make sure the air conditioner plug is pushed completely into tile outlet.

• Check tile house fixse/circuit breaker box and replace tile flxseor reset tile breakeL

• Tile unit will automatically restart in tile settings last used after the power is restored.

• There is a protective time del W (approximately 3 minutes) to prevent tripping of tile compressor

overload. Fox this reason, tile unit may not start normal cooling for 3 minutes after it is turned

back on.

use of tile air conditioner and contact a qualified service technician.

• On models with control kalobs, mrn tile temperature knob m a higher numbeL

See tile Care and Cleaning section.

to allow time for file room to cool down.

Cold air is escaping. • Gheck for open fiunace regfiste_ and cold air returns. Cooling coils have iced up. • See "Air conditioner freezing up" below.

Air conditioner freezingup

Ice blocks the air flow and stops the air conditioner

from cooling the room.

• On models widl conUol knobs, set die mode conuol at

HighFanor HighCoolwitb the rempat I or 2.

• On models with touch pads, set tile controls at HighFan or High Cooland set the tbemlosmt m a higher tempex_mxre.

Theremote control The batteries are inserted *Check tile position of tile batteries. Tile), should be

is not working incorrectly, inserted in tile opposite (+) and (-) direction.

The batteries may be dead. =Replace the batteries.

Waterdrips outside Hot, humid weather. • This is normal. Waterdrips indoors The air conditioner is not • Fox proper water disposal, make sure tile air conditioner

tilted to the outside, slants slightly from the case flont to the real

Watercollects in Moisture removed from air • This is normal for a short period in areas with little

basepan and drains into base pan. humidiD,; hernial for a longer period in very humid areas.

Normal Operating Sounds

You may hear a pinging noise caused by water

being picked up and thrown against tile condenser on rainy dws or when the humidity is high. This design feature helps remove moisture and improve efficiency.

}_You may hear tile thernlosmt click when tile

compressor cycles on and off:

Water Mll collect in die base pan during high humidity or on rainy days. Tile wamr may overflow and drip flom tile outdoor side

of tile unit.

}_Tile fan may run even when tile compressor

does not.

Please place in envelope and mail to:

Veuillez mettre dans une enveloppe et envoyez _ :

OWHERSHIPREGISTRATIOH P.O. BOX1780

MISSJSSAUGA,OHTARIO L4Y4G1

(FORCAHADIAHCOHSUMERSOHLY)

For Canadian

Customers

Pour les

Consommateurs Canadiens

Pleaseregisteryourproductto enableustocontactyou VeuiUezenregistrervotreproduitafindenouspermed_ede

in the remote event a safety nonce is issued for this product communiquer avec vous sijamais un avis de s6curi_ concemant

and to aUow for efficient communication under the terms ce produit et,ait6mis et de communiquer facibment avec vous en of your warrant_; should the need arise, vertu de vol_ garan_e, si le besoin s'en fair sentir.

REGISTERON-UNE: www.geappliances.ca MAILTO:, P.O.BOX1788,MISSISSAUGA

ENREGISTREMENTSURINTERNETA:www.electrornena,qersge.ca POSTERA: ONTARIO,L4Y4GI

Z I

[][] MISS/MLLE.MR'/M[][] Ms.MRS'/MNE"FIRSTNAME/PRt_NOM LASTNAME/NOM

STREETNO/N° RUE STREETNAME/RUE

C31

kkll ZI

CITY/VILLE

PROVINCE POSTALCODE/POSTAL

'AR COOE,,NOREOL'LEP.ONE[EOOL

DiDYOUPURCHASEASERVICECONTRACTFORTHISAPPLIANCE? AVEZ-VOUSACHETEUN CONTRATDESERVICEPOURCETAPPAREIL?

NAMEOF SELLINGDEALER/ NOM DU MARCHAND MODEL / MODELE

INSTALLATIONDATE/DATED'INSTALLA_ION/

Y/A M D/J CORRESPONDENCE [] ENGLISH

D Ido notwishto receiveanypromotionaloffers_egardingthisproduct. El Jened6sirepasrecevoird'offrespromotionnelbsconcemantceproduit.

CORRESPONDANCE [] FRANOAIS SERIAL/SI_RI E

YES/OUI[]

NO/NOND

IFYES/SIOUhEXPIRATION

Y/A M D/J

APT.NO/APP./RR#

GEAir Conditioner--One YearLimited Warranty.(For customers in the U.S.A.)

Staple your receipt here. Proof of the original purchase date is needed to make a warranty claim.

We Will Replace:

Replacement unitfor any product which fails due to a defect in materials or workJnanship.

Fromthe date ofthe originalpurchase

The replacement unit is warranted for the remainder of your product's original one:year warranty period. The replacement unit may either be a new unit or a refurbished unit.

Properly pack your unit. We recommend using the original carton and packing materials.

Return the product to the retail location where it was purchased.

Locate your original sales receipt and make a note of your model and serial number.

Call GE at 1.866.907.1655 to initiate the product replacement process.

You will be asked to provide your name, address, date of purchase, model and serial number.

GE will arrange for a carton to be sent to your home to recover the product.

Customer instruction. This owner's manual provides information regarding operating instructions and

user controls. Improper installation. If you have an installation problem,

or if the air conditioner is of improper cooling capacity for the intended use, contact your dealer or installer.

You are responsible for providing adequate electrical connecting facilities.

Failure of the product resulting from modifications to

the product or due to unreasonable use including failure to provide reasonable and necessary maintenance.

Include in the package a copy of the sales receipt or other

evidence of date of original purchase. Also print your name and address and a description of the defect.

You must return the product (postage pre-paid by GE) to GE's recovery center before a replacement unit will be provided. Please include a description of the defect.

You should receive your replacement product within 7 to 10 business days after your unit is received.

If you experience any problems or delays after initiating the replacement process, please call 1.256.796.6610 for

assistance.

Replacement of house fuses or resetting of circuit breakers.

Failure due to corrosion on models not corrosion- protected. Damage to the product caused by improper power

supply voltage, accident, fire, floods or acts of God. Incidental or consequential damage caused by possible

defects with this air conditioner.

Damage caused after delivery.

EXCLUSIONOF IMPLIED WARRANTIES--Your sole and exclusive remedy is product replacement as provided in this Limited Warranty. Any impfied warranties, including the implied warranties of merchantability or fitness for a particular purpose, are limited to one year or the shortest period allowed by law.

This warranty is extended to the original purchaser and any succeeding owner for products purchased for home

use within the USA. Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives

you specific legal rights, and you may also have other rights which vary from state to state. Toknow what your legal rights are, consult your local or state consumer affairs office or your state's Attorney General

Exclusion of implied warranties: Except where prohibited or restricted by law, there are no warranties, whether express, oral or statutory which extend beyond the description on the face hereof, including specifically the

impfied warranties of merchantability or fitness for a particular purpose.

Warrantor: General Electric Company.Louisville, KY 40225 15

+ 33 hidden pages