GE AEH18DSQ1, AEH18DQQ1, AEH18DPQ1, AEH18DPH1 Owner’s Manual

GEAppliances.com

Safety Instructions ............. 2, 3

Operating Instructions

Controls ........................... 4-6

Care and Cleaning

Air Filter .............................. 6

Outdoor Coils ......................... 6

Installation Instructions ...... 7-13

AEH18*

0_

0_

0

Troubleshooting Tips ............ 14

Normal Operating Sounds ............ 14

Consumer Support

Consumer Support .......... Back Cover

Ownership Registration for

Customers in Canada only ........ 1S, 16

Warranty for Customers

in Canada ........................... 18

Warranty for Customers

in the U.SA........................... 17

*ENERGY STAR ® labeled product

STAR

Climatiseur

La section franqaise commence 5 la page 19

Acondicionador

deaire

La secci6n en espaflol empieza en la p6gina 37

As an ENERGYSTAR®partner, GE has

determined that this product meets
the ENERGYSTAR®guidelines for
energy efficiency.

Write the model and serial numbers here:
Model #

Serial #

Find these numbers on a label on the sideof
the air conditioner.

In Canada, contact us at:
www.GEAppliances.ca

49-7686 12-10 GE

IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

Foryour safety, the information in this manual must be followed to minimize the risk of fire, electric

shock or personal injury.

SAFETYPRECAUTIONS

Use this appliance only for its intended
purpose as described in this Owner's

Manual.

This air conditioner must be properly

installed in accordance with the Installation
Instructions before it is used.

Never unplug your air conditioner by pulling
on the power cord. Always grip plug firmly
and pull straight out from the receptacle.

Replace immediately all electric service
cords that have become frayed or otherwise
damaged. A damaged power supply cord
must be replaced with a new power supply

cord obtained from the manufacturer and
not repaired. Do not use a cord that shows

cracks or abrasion damage along its length
or at either the plug or connector end.

Turn the unit OFFand unplug your air

conditioner before cleaning.
GEdoes not support any servicing of the

air conditioner. We strongly recommend

that you do not attempt to service the air

conditioner yourself.

For your safety...do not store or use
combustible materials, gasoline or other

flammable vapors or liquids in the vicinity

of this or any other appliance.

Allair conditioners contain refrigerants,
which under federal law must be removed

prior to product disposal. If you are getting
rid of an old product with refrigerants, check

with the company handling disposal about
what to do.

If the receptacle does not match the plug,

the receptacle must be changed out by u

qualified electrician.

These R410A air conditioning systems

require contractors and technicians to
use tools, equipment and safety standards
approved for use with this refrigerant.
DO NOT use equipment certified for
R22 refrigerant only.

HOW TO CONNECT ELECTRICITY

Do not, under any circumstances, cut or remove
the third (ground) prong from the power cord.
For personal safety, this appliance must be
properly grounded.

DO NOT use an adapter plug with this appliance.

The power cord of this appliance is equipped
with o 3-prong (grounding) plug which mutes
with u standard 3-prong (grounding) wall outlet
to minimize the possibility of electric
shock hazard from this appliance.

Power cord includes u current interrupter device.
A test and reset button is provided on the plug
case. The device should be tested on u periodic
basis by first pressing the TESTbutton and
then the RESETbutton while plugged into the
outlet. If the TESTbutton does not trip or if the
RESETbutton will not stay engaged, discontinue
use of the air conditioner and contact a qualified

2

service technician.

Have the wall outlet and circuit checked by
a qualified electrician to make sure the outlet
is properly grounded.

Where a 2-prong wall outlet is encountered,
it isyour personal responsibility and obligation to
have it replaced with u properly grounded
3-prong wall outlet.

The air conditioner should always be plugged
into its own individual electrical outlet which has

u voltage rating that matches the rating plate.
This provides the best performance and also

prevents overloading house wiring circuits which
could cause a fire hazard from overheated wires.

See the Installation Instructions, Electrical
Requirements section for specific electrical

connection requirements.

GEAppliances.com

WARNING!

USEOF EXTENSION CORDS

RISK OF FIRE. Could couse serious injury or
death.

• DONOT use an extension cord with this
Window Air Conditioner.

• DONOT use surge protectors or multi-outlet
adaptors with this Window Air Conditioner.

READAND FOLLOWTHISSAFETYINFORMATIONCAREFULLY.

SAVETHESEINSTRUCTIONS

About the controlson the air conditioner

Features and appearance will vary.
Lights next to the touch pads on the air conditioner control panel indicate the selected settings.

NOTE:Thedisplayalways
showsthe roomtemperature
exceptwhensettingthe Set
temperatureor the Delaytimer.

-- High m Cool Mode select

0 --Auto Cq_lp_- Decrease 0

-- ('-Fan-_ &o 0_,,Speed_ d _#_ Decrease 0

Med u Energy Saver

-- Low iFan Onlg Fan speed

I set Increase

Lightindicatesthe unit
is in thetemperatureor
delaytime Set mode.

T_g_ Delay1-24hr

Lightindicatesthe

delay timer is set.

Air Conditioner Controls

Controls

O Power Pad 0

Turns air conditioner on and off.When turned
on,the display will show the room temperature.

O Display

Shows the room temperature ortime remaining
on the Delaytimer. Showsthe Settemperature

while setting the temperature in Cool or Energy
Saver modes. TheSet light will turn on while

setting.

O emp Increase •/Decrease • Pads

Useto set temperature when in Cool or Energy

Saver mode. TheSet light will turn on while
setting.

O elay Timer Increase • (4-I/Decrease • (-)

Pads

Eachtouch of the Increase • / Decrease •

pads on the unit or the Increase + / Decrease

- pads on the remote control willset the delay
time when using the Delay 1-24hr timer. The

Set light willturn on while setting.

O an Speed Pads

Useto set the fan speedto Low, Med, High

orAuto on the unit. NOTE:On the remote
control, use the fan speed Increase + /

Decrease - pads to set the fan speedsto Low,
Med or High. UsetheAuto pad to turn Auto

fan on.

Delaytimer O

Temperature

andDecrease

0

Delaytimer Increase

I _ _ i _AutoFanon

II _t_ +_._i_ FanspeedIncrease

Remote Control

Mode Pad

Useto set the air conditioner to Coo/,Energy

Saver or FanOnly mode.

Delay Pads/Delay 1-24hr Pad

Delay ON--When the air conditioner is off, it can

be set to automatically come on in 1 to 24 hours

at its previous mode and fan settings.
Delay OFF--When the air conditioner is on,

itcan be set to automatically turn off in 1 to
24 hours.

How to set:

Pressthe Delay 1-24hr pad on the unit or the

Delay pad onthe remote control. Eachtouch

of the Increase • / Decrease• pads on the

unit or the Increase + / Decrease - pads on

the remote control will set the timer in 1-hour

intervals.The Set light will turn on while setting.

To review the remaining time on the Delay
1-24hr timer, press the Delay 1-24hr pad on

the unit or the Delay pad on the remote control.

Usethe Increase • / Decrease • pads on the

unit or the Increase + / Decrease - pads on the
remote control to set a new time if desired.

To cancel the timer, press the Delay 1-24hr pad
until the light on the Delay 1-24hr pad goes off.

Note: The default temperature reading on the display is degree Fahrenheit (°F). Tochange the display to
degree Celcius (°C),press the Temp Increase • and Temp Decrease • buttons together and hold for :3
seconds. Repeat the process to change back to degree Fahrenheit (°F)

4

Do Not Operate in Freezing Outdoor Conditions
Thiscool-only air conditioner was not designed for

freezing outdoor conditions. It must not be used in
freezing outdoor conditions.

Remote Control

Toensure proper operation,dim the remote
control ot the signal receiver on the air

conditioner.
Hake sure nothing is between the airconditioner

and the remote control that could block the
signal.

Cool Mode

GEAppliances.com

Theremote control signal has o rangeof
up to 20 feet.

Make sure batteries ore fresh and installed
correctly os indicated on the remote control.

Remotecontains o magnet allowing it to attach
to metal surfaces.

Usethe Cool mode atLow,Med, High or Auto Fan

Speedfor cooling.Usethe Temperature Increase •
/ Decrease • podsto set the desiredtemperature

between 64°F and 86°F in l°F increments.
An electronicthermostat is usedto maintain the room

temperature. Thecompressorwill cycle on
and off to keep the room ot the set level of comfort.

Setthe thermostat ot o lowernumber and the indoor
air will become cooler.Setthe thermostat ot o higher

number and the indoor air will become warmer.

NOTE:Iftheair conditioner isoff ond is then turned on
while set to o Cool setting or if turned from o fan

setting to o Cool setting,it may take approximately
3 minutes for the compressor to start and coolingto
begin.

Energy Saver Mode

Controlsthe fan.
ON--The fan will cycleon and off with the

compressor.This results in wider variations of room
temperature and humidity. Normally usedwhen the
room isunoccupied. NOTE:Thefan may continueto
run for a short time after the compressor cyclesoff.

Cooling Descriptions

For Normal Cooling-Select the Cool mode and
High orF/edfan with o middle set temperature.

For Maximum Cooling--Select the Cool mode
and High fan with o lower set temperature.

For Quieter and Nighttime Cooling-Select the

Cool mode and Low fan with o middle set
temperature.

OFF--Thefan runsoil the time, while the compressor
cycles on and off.

Fan Only Mode

Usethe FanOnly Node ot Low, Ned or High fan
speedto provide air circulation and filtering without

cooling. Sincefan-only settings do not provide
cooling, o Settemperature cannot be entered. The

room temperature will appear in the display.

Auto Fan Speed

Setto Auto fan speedfor the fan speedto
automatically set to the speed needed to provide
optimum comfort settings with the settemperature.

If the room needsmore cooling, the fan speed
will automatically increase.If the room needs less

Power Outage Recovery Feature

Inthe case of o power outage or interruption, the
unit will automatically restart in the settings last
used offer the power isrestored. Ifthe Delay 1-24hr

NOTE:Auto FanSpeedcannot be usedwhen in the
Fan Only Mode.

cooling, the fan speedwill automatically decrease.

NOTE:Auto FanSpeedcannot be used when in the
Fan Only Mode.

feature was set,it will resume countdown. You may
need to set o new time if desired.

About the controlson the air conditioner

Additional important information.

Air Direction

Usethe lever to adjust the air direction left and right

only.

Careand cleaningof the air conditioner.

Grille and Case

Turn the air conditioner off and remove the plug from Toclean,usewater and a mild detergent. Do not use
the wall outlet before cleaning, bleachor abrasives.

Air Filter

Theair filter behind the front grille should be checked
and cleaned at least every 30 days or

more often if necessary.

Toremove:

Open the inlet grille by pulling downward on the tabs
at the top upper corners of the inlet grille until the

grille is in a 850position. Removethe filter.
Cleanthe filter with warm, soapy water. Rinseand let

the filter dry before replacing it. Donot cleanthe filter
in a dishwasher.

CAUTION:_oNoro_erotetheair

conditioner without o filter becausedirt and lint will
clog itand reduceperformance.

Tab Tab

Outdoor Coils

Thecoils on the outdoor sideof the air conditioner
should be checked regularly. Ifthey are clogged with

dirt or soot,they may be professionallycleaned.

How to Insert the Batteries in the Remote Control

-] emovethe battery cover by sliding it according

to the arrow direction.

[2] Insertnew batteries, makingsure that the (+)

and (-) of battery are installed correctly.

[-_ Reattachthe cover by sliding it back

into position.

6

NOTES:

Use2"AAA"(1.5volt) alkaline batteries. Do not

use rechargeable batteries.

Removethe batteries from the remote control if

the system isnot going to be usedfor a long time.

Donot mix old and new batteries. Donot mix

alkaline,standard (carbon-zinc)orrechargeable
(ni-cad,ni-mh,etc) batteries.

Installation

Air Conditioner

Instructions

r-_ Questions? Call 800.GE.CARES(800.432.2737)or Visit our Website at: GEAppliances.com

I

In Canada, call 1.800.561.3344or visit www.GEAppliances.ca I

BEFOREYOU BEGIN

Read these instructions completely

and carefully.

• IMPORTANT- Savetheseinstructions

for local inspector's use.

• IMPORTANT--Observe all governing

codes and ordinances.

• Note to Installer- Be sure to leave these
instructions with the Consumer.

• Note to Consumer - Keep these instructions for
future reference.

• Skill level- Installation of this appliance

requires basic mechanical skills.

• Completion time - Approximately 1 hour

• We recommend that two people install
this product.

• Proper installation is the responsibility
of the installer.

• Product failure due to improper installation is not
covered under the Warranty.

• You MUST use all supplied parts and use proper
installation procedures as described in these

instructions when installing this air conditioner.

CAUTION:

Do not, under any circumstances, cut or remove
the third (ground) prong from the power cord.

Do not change the plug on the power cord
of this air conditioner.

Aluminum house wiring may present special
problems--consult a qualified electrician.

TOOLSYOUWILL NEED

Phillips head screwdriver

Flat-blade screwdriver

(_ ELECTRICALREQUIREMENTS

Some models require a 115/120-volt AC,

(_ 60-Hz grounded outlet protected with a

possibility of electric shock hazard. If the wall outlet

you plan to use is only a 2-prong outlet, it isyour

responsibility to have it replaced with a properly

grounded 3-prong wall outlet.

©

15-amp time-delay fuse or circuit breaker.

The 3-prong grounding plug minimizes the

Some models require 230/208-volt AC,

protected with a time-delay fuse or circuit
breaker. These models should be installed on

their own single brunch circuit for best

performance and to prevent overloading

house or apartment wiring circuits, which
could cause a possible fire hazard from
overheating wires.

Pencil Ruler or tape measure

Level Scissors or knife

Power cord includes u current interrupter device. A
test and reset button is provided on the plug case. The
device should be tested on a periodic basis by first
pressing the TESTbutton and then the RESETbutton
while plugged into the outlet. If the TESTbutton does
not trip or if the RESETbutton will not stay engaged,

discontinue use of the air conditioner and contact a
qualified service technician.

PARTS INCLUDED

(Appearance may vary)

Installation Instructions

Top rail gasket (1)

Window

seal

Foam top window _u_,

gasket (1) _

Top

mounting

rail

Side rail (2)

Right

accordion

panel

\

V-supports (2)

Type A Type B Type C

screws (10) screws (2) screws (4)

Sill angle

bracket (2)

Window

locking bracket

(2)

®

Type Ebolt with

nut (4)

8

®

Type F bolt with

nut (2)

Installation Instructions

D WINDOW REQUIREMENTS

•These instructions are for a standard double-hung
window. You will need to modify them for other types

of windows.

• All supporting parts must be secured
to firm wood, masonry or metal.

• The electrical outlet must be within reach of the

power cord.

• Follow the dimensions in the table and illustration
for your model.

1

18.5/'

26"- 41 "

(With accordion panels)

I

[] STORMWINDOW REQUIREMENTS

A storm window frame will not allow the air
conditioner to tilt toward the outside, and will keep it

from draining properly.
To adjust for this, attach a piece of wood to the sill.

WOODPIECES
WIDTH:2"

LENGTH:Long enough to fit inside the window

frame.
THICKNESS:To determine the thickness, place a

piece of wood on the sill to make it 1/2" higher
than the top of the storm window frame or the vinyl

frame.
Attach securely with nails or screws provided by the

installer.

1/2" higher

than vinyl frame

D PREPARETHEAIR CONDITIONER

[] Pull down the front panel and remove the filter.

Remove the front panel by lifting up at an
angle.

r_ Remove the four front screws. Save them

for reinstalling the front housing.

[-C-]Grasp the lower corners of the grille while

pressing in on the case sides with your
finger tips. Pull out to release and lift it up.

NOTE: Do not pull the bottom edge
toward you more than 3" or you may
damage the tabs of the grille.

e

When the front grille is removed the

@

control panel will still be attached by
a harness. Turn the grille around so
you can see the back side of the grille.
Remove the 2 screws to separate the
control panel housing from the grille.

NOTE: Be sure to save these screws. You will
need them later in the installation.

1/2" higher

than storm
window
frame

Storm window

frame

_ _(°ns°mewind°ws v/Woo d

- r'- Vinylframe I I

Remove Screws

9

Installation Instructions

D PREPARE THE AIR CONDITIONER

(continues)

[_ Remove the ground screw from the left

side of the case. Keep it in a safe location.
NOTE: Be sure to save this screw. You will need

them later in the installation.

[] Slide the air conditioner from the case by

gripping the base pan handle and pulling
forward while bracing the case. Do not
pull or lift on the styrofoam discharge area.

Do not

D PREPARETHE CASE

r-c] Slide each side retainer onto the edge of

each according panel. The figure shows teh
orientation of each accordion panel and side
retainer assembly relative to the case from a

top view of the unit.

SIDE RETAINER

pull

damage

unit may

FRONT

D PREPARETHE CASE

[] Attach the top rail gasket to the bottom

of the top rail.

[-_ Install the top mounting rail with 4 type A

screws from the inside of the case. Press
firmly to drive the screws into the gasket

and through the top mounting rail.

area i

to the

result

[] Slide the left and right accordion panels

into the top and bottom mounting rails.

Top!eft_ ., _ P_

Topmo nting rail To ight

/

Bottom mounting rail

E] Attach the side retainers to the case using 6

type A screws.

....o o]} y

0

Installation Instructions

D PREPARETHEWINDOW AND INSTALL

THECASE

[] Cut the window sash seal to the proper length.

Peel off the backing and attach the seal to the

underside of the window sash.

r_Open the window and mark the center of

the window sill.

[] Carefully slide the case into the window

and center the case. Lower the window

behind the top mounting rail. Pull the
bottom of the case forward so that the

bottom mounting rail is tight against the
back of the window stool. Mount the case

to the window sill using 2 type B screws.

Drill pilot holes, if necessary.

t JlL _L

Fs]PREPARETHE WINDOW AND INSTALL

THECASE(continues)

[] Position the V-supports J_,

on the case bottom so
that they will be near

the outside wall. Attach
a V-support to each side

of the bottom of the case
with Type E bolts, 2 for

each support.
Adjust sill angle brackets to rest on sill.

E3

r_ Extend the left and right accordion panels

to the vertical window sashes. Drill pilot
holes and attach the top corners with 2 type

C screws.

TypeC
screw

tpport

screw

c

2type Bscrews

Stool

r_ Assemble the V-support and V-support

bracket with Type F nut and bolt

Type Ebolt

nut

Left

Sillangle

brocket __ _

V-support Type

Fbolt and nut

_ht

11

Installation Instructions

DPREPARE THE WINDOW AND INSTALL

THECASE(continues)

[] CAUTION:

To prevent broken Vinyl

glass or damage to

windows, on vinyl or

other similarly

constructed windows,

attach the window
locking bracket to the window side jamb.

Attach the window locking Wood

bracket with one Type C

screw.
This unit contains two

window locking brackets.

[]-] Cut the foam top window gasket to the

window width.

r_ stuff the foam

between the
glass and the

window to
prevent air and

insects from getting into the room.
NOTE: If the gasket supplied does not fit
your window, obtain appropriate material
locally to provide a proper installation seal.

INSTALL THE AIR CONDITIONER
IN THE CASE (continues)

[] Replace the 1 screw removed earlier, one

on each side of the case.

IMPORTANT: THE GROUND SCREWS MUST BE
REINSTALLEDTO ENSURE PROPERGOUND.

[_ Reinstall the control to the panel housing by

replacing the 2 screws you removed earlier.

Screws

Attach the front grille to the case by inserting
the tabs on the grille into the slots on the

front top of the case. Push the grille in.

[] INSTALL THE AIR CONDITIONER

IN THE CASE

Slide the air conditioner into the case by
the base pan. Do not push on the controls,

styrofoam air discharge housing or the finned
coils. Make sure the air conditioner is firmly

seated.

:_!!iF_!!!!!!!

Do not presson
these areas-

damage to the unit
may result

Base Pan

['_ Replace the screws.

[_] Install the filter and the front grille.

[_ Plug in the air conditioner.

12

Through-the-Wall Installation Instructions--Optional

The case may be installed through-the-wall
in both existing and new construction.

Read completely, then follow step-by-step.

NOTE: Obtain all materials locally for
mounting the air conditioner through-

the-wall.

IMPORTANT

%

Through-the-wall installation is not
appropriate if any of the side or top louvers

in the case will be obstructed by the wall.
All side and top louvers in the case must

project on the outdoor side of the wall.
The room side of the case must project

into the room far enough to maximize the
balance of the unit.

The case must be installed level from side-
to-side and with a slight tilt from front to

rear. Use a level; no more than a 1/2 bubble
will be the correct case slant to the outside.

Lintel angle is required to support bricks or
blocks above opening.

Flashing is required and should extend the
length of the opening to ensure no inside

cavity leakage occurs.

Remove the air conditioner from the case.
For specific instruction, refer to the Window

Installation Instructions.
Make certain that a wall receptacle is

available close to the hole location or make
arrangements to install a receptacle.

ITI IMPORTANT (cont.)

F_ Secure with 14 wood screws anchored at

least an inch into the wall support structure.
NOTE: Drill pilot holes, if necessary, for

proper installation. If the frame is oversized,
use shims to prevent case distortion.

[] FINISH THE WALL OPENING

[] Caulk all four sides on the outdoor side of

the case to prevent moisture from getting
through to the interior wall. Use of flashing
(drip rail) will further prevent water from
dripping inside the wall and down the
outside of the building.

[_ Plaster line

Caulking

OUTSIDE

Air louvers (top /

and sides must/
project on thev

outdoor side of

the wall)

Wood filler and
caulking (above an

below the flashinc

• II """ desired)

rl Trim molding (if

INSIDE

Bottom rail

J

Place the case in the wall opening and

@

place wood support strips between the case
bottom and the flashing on both sides of the

bottom rail. They should be the same height
as the bottom rail and the same length as
the wall openin.q.

Flashing
(Drip rail)

Flashing

(Drip rail)

F_ Place the air conditioner into the case.

For specific instruction, refer to the Window

Installation Instructions.

Wood support strips

13

Bottom
rail

TroubleshootingTips.

PossibleCauses What To Do
Theair conditioner • Hake surethe air conditioner plug ispushed

doesnotstart _sunplugged, completely into the outlet.

Thefuse isblown/circuit .Check the housefuse/circuit breaker box and replace

breaker is tripped, the fuse or resetthe breaker.
Power failure. .The unitwill automatically restart in the settings last

usedafter the power is restored.

•There is a protective time delay (approximately
:3minutes) to prevent tripping of the compressor

overload. For this reason, the unit may not start

normal cooling for :3 minutes after it is turned
back on.

The current interrupter • Pressthe RESETbutton located on the power cord plug.
device istripped. • If the RESETbutton will not stay engaged, discontinue

use of the air conditioner and contact a qualified

service technician.

Airconditionerdoes Airflow is restricted. • Hake surethere are nocurtains, blindsor furniture
notcoolasitshould blocking the front of the air conditioner.

Thetemp control may • In the Coolmode,pressthe Decrease• pad.

not be set correctly.

Theair filter is dirty. .Clean the filter at leastevery :30days.

Seethe CareandCleaningsection.

Theroom may have been hot. .When the air conditioner isfirst turned on,you need

to allow time for the room to cool down.

Coldair isescaping. .Check for open furnace registersand cold air returns.
Cooling coils have iced up. .See "Air conditionerfreezingup"below.

Aircondtioner Ice blocks the air flow •Setthe controls at HighFanor HighCooland setthe

freezingup and stops the air conditioner thermostat to a highertemperature.

from cooling the room.

Theremotecontrol Thebatteries are inserted .Check the position of the batteries.They should be

isnotworking incorrectly, inserted in the opposite (+)and (-) direction.

Thebatteries may bedead. • Replacethe batteries.
Water dripsoutside Hot,humid weather. .This isnormal.
Water dripsindoors The air conditioner is not • For proper water disposal,make surethe air conditioner

tilted to the outside, slants slightlyfrom the case front to the rear.
WaterCollectsin

basepan

Normal Operating Sounds

You may hear a pinging noisecaused by
water being picked up and thrown against the
condenser on rainy days or when the humidity
is high.Thisdesign feature helps remove
moisture and improve efficiency.

You may hearthe thermostat click when the
compressor cycles on and off.

Moisture removed from air

and drains into base pan.

•This isnormal for a short period in areas with little
humidity; normal for a longerperiod invery humid areas.

Water will collect inthe base pan during

high humidity or on rainy days.The water
may overflow and drip from the outdoor side

of the unit.

iiiiiiiiiiii_iii

Thefan may runeven when the compressor
does not.

14

Notes.15Notes.

16

GEAir Conditioner--One-Year Limited Warranty. (Forcustomers in theU.S.A.]

All warranty service provided by our Factory Service Centers,

or an authorized Customer Care®technician. To schedule service,
visit us on-line at ge.com, or call 800.GE.CARES (800.432.2737).
Have serial number and model number available when calling

for service.

GE Will Replace:

Any part of the air conditioner which fails due to a defect in materials or workmanship.

Eromthedateof the
origina!purchase

Service trips to your home to teach you how to
use the product.

Improper installation, delivery or maintenance. Ifyou
have an installation problem, or if the air conditioner

isof improper cooling capacity for the intended use,
contact your dealer or installer. You are responsible

for providing adequate electrical connecting facilities.

Failure ofthe product resulting from modifications to

the product or dueto unreasonable use including failure
to provide reasonable and necessary maintenance.

In commerciallocations, labor necessary to move the
unit to a location where it is accessible for service

by an individual technician.

Duringthis limited one-year warranty, GEwill also provide, free of charge, all labor and related
serviceto replace the defective part.

Stapleyour receipt here.

Proof of the original purchase

date is needed to obtain service

under the warranty.

Replacement of house fuses or resetting of circuit
breakers.

Failure due to corrosionon models not corrosion-
protected.

Damage to the product caused by improper power
supply voltage, accident, fire, floods or acts of God.

Incidental or consequential damage caused by possible
defects with this air conditioner.

Damage caused after delivery.

EXCLUSION OF IMPLIED WARRANTIES--Your sole and exclusive remedy is product repair as provided in
this Limited Warranty. Any implied warranties, including the implied warranties of merchantability or
fitness for a particular purpose, are limited to one year or the shortest period allowed by law.

This warranty is extended to the original purchaser and any succeeding owner for products purchased for
home use within the USA. If the product is located in an area where service by a GE Authorized Servicer is
not available, you may be responsible for a trip charge or you may be required to bring the product to an

Authorized GE Service location for service. In Alaska, the warranty excludes the cost of shipping or service calls

to your home.

Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty
gives you specific legal rights, and you may also have other rights which vary from state to state. To know

what your legal rights are, consult your local or state consumer affairs office or your state's Attorney General.

Warrantor: General Electric Company. Louisville, KY 40225

17