GE ADT521PGFWS, ADT521PGFBS, GDF540HMFES, GDF540HSFSS, GDF520PSFSS Owner's Manual
GEAppliances.com
Safety Instructions ............. 2-3
Operating Instructions
Care and Cleaning .................. 11
Getting Started ..................... 4-5
Loading and Place Settings ......... 8-9
Loading the silverware baskets ...... 10
Using the Dishwasher ...............6-7
Troubleshooting Tips ......... 12-14
Consumer Support
Consumer Support ....................16
Warranty ............................15
Owner’s Manual
Dishwashers
GDF510-540 Series
GDT530-550 Series
Lave-vaisselle
Manuel d’utilisation
La section française commence à la page 17
Lavaplatos
Manual del propietario
La sección en español empieza en la página 33
Printed in the United States
FRONT CONTROL MODELS TOP CONTROL MODELS
Write the model and serial
numbers here:
Model # _________________
Serial # __________________
Dishwashers
You can find them on the tub wall
just inside the door.
49-55082-5 04-13 GE
IMPORTANT SAFETY INFORMATION
5($'$//,16758&7,216%()25(86,1*³
SAVE THESE INSTRUCTIONS
WARNING!
For your safety, the information in this manual must be followed to minimize the risk of fire,
explosion, electric shock, and to prevent property damage, personal injury, or death.
WARNING!
Under certain conditions, hydrogen gas may be produced in a water heater that has not been used for two or
more weeks. HYDROGEN GAS IS EXPLOSIVE.
If the hot water has not been used for two or more weeks, prevent the possibility of damage or injury by turning
on all hot water faucets and allow them to run for several minutes. Do this before using any electrical appliance
connected to the hot water system. This simple procedure will allow any built-up hydrogen gas to escape. Since
the gas is flammable, do not smoke, use an open flame, or use the appliance during this process.
WATER HEATER SAFETY
When using your dishwasher, follow basic precautions,
WARNING!
Use this appliance only for its intended purpose
as described in this Owner’s Manual.
Do not operate your dishwasher unless all enclosure
panels are properly in place.
Do not store or use combustible materials, including
gasoline or other flammable liquids or vapors in the
vicinity of this or any other appliance.
WARNING!
This dishwasher must be properly installed and located in accordance with the Installation Instructions
before it is used. If you did not receive an Installation Instructions sheet with your dishwasher, you can
receive one by visiting our Website at GEAppliances.com. In Canada, visit www.GEAppliances.ca.
Connect the dishwasher/appliance to a grounded
metal, permanent wiring system; or run an
equipment-grounding conductor with the circuit
conductors and connect to the equipmentgrounding terminal or lead of the appliance.
Improper connection of the equipment-grounding
conductor can result in a risk of electric shock. Check
with a qualified electrician or service representative
if you are in doubt whether the appliance is properly
grounded.
Dispose of discarded appliances and shipping
or packing material properly.
including the following:
Do not abuse, sit on or stand on the door or dish rack
of the dishwasher.
Do not tamper with controls.
Do not wash plastic items unless marked
dishwasher safe or the equivalent. For plastic
items not so marked, check the manufacturer’s
recommendations.
PROPER INSTALLATION AND MAINTENANCE
Do not attempt to repair or replace any part
of your dishwasher unless it is specifically
recommended in this manual. All other servicing
should be referred to a qualified technician.
To minimize the possibility of electric shock,
disconnect this appliance from the power supply
before attempting any maintenance.
NOTE: Turning the dishwasher off does not
disconnect the appliance from the power supply. We
recommend having a qualified technician service
your appliance.
2
IMPORTANT SAFETY INFORMATION
5($'$//,16758&7,216%()25(86,1*³
SAVE THESE INSTRUCTIONS
WARNING! RISK OF CHILD ENTRAPMENT
Do not allow children to play with, on or inside this appliance at any time.
PROPER DISPLOSAL OF THE DISHWASHER
Junked or abandoned dishwashers are dangerous…even if they will sit for “just a
few days.” If you are getting rid of your dishwasher, please follow the instructions
below to help prevent accidents.
Do not allow children to play with, on or inside this or any discarded appliance.
Take off the door of the washing compartment or remove the latch by
removing the two screws from the latch receiver inside the tub (as shown).
CAUTION: To prevent minor injury and property damage
During or after wash cycle, contents may be hot to
the touch. Use care before handling.
Using a detergent that is not
specifically designed for dishwashers
will cause the dishwasher to fill with
suds.
Non-Dishware Items: Do not wash items such
as electronic air cleaner filters, furnace filters
and paint brushes in your dishwasher. Damage
to the dishwasher and discoloration or staining
of the dishwasher may result.
Close supervision is necessary if this appliance
is used by or near children.
GEAppliances.com
Load light-weight, plastic items so they do not
become dislodged and drop to the bottom of the
GLVKZDVKHU³WKH\PLJKWFRPHLQWRFRQWDFWZLWK
the heating element and be damaged.
Locate sharp items so that they are not likely to
damage the door seal.
Load sharp knives with the handles up to reduce the
risk of cut-type injuries.
Do not allow children to play around the dishwasher
when opening or closing the door due to the
possibility of small fingers being pinched in the door.
Do not touch the heating element during or
immediately after use.
CAUTION: ELECTRICAL REQUIREMENTS
This appliance must be supplied with 120V, 60 Hz,
and connected to an individual, properly grounded
branch circuit, protected by a 15 or 20 amp circuit
breaker or time-delay fuse.
If the electric supply provided does not meet the
above specifications, it is recommended that a
licensed electrician install an approved outlet.
Your dishwasher circuit should not be used for
any other appliance while the dishwasher is in
operation as the dishwasher requires the full
capacity of the circuit.
If the wall receptacle you plug the dishwasher’s
power cord into is controlled by a switch, turn on
the switch.
NOTICE
If your dishwasher is connected to a wall
switch, ensure that the switch is on prior
to use.
If you choose to turn the wall switch
off between wash cycles, allow 5-10
seconds after turning the switch on before
touching Start to allow the control to
initialize.
Use only powder, Cascade
liquid detergents or rinse agents recommended
for use in a dishwasher and keep them out of the
reach of children. Cascade
Automatic Dishwashing Detergent, and Cascade
Rinse Aid™ rinse agents have been approved for use
in all GE dishwashers.
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
®
All-in-1 ActionPacs™,
®
All-in-1 ActionPacs™
SAVE THESE INSTRUCTIONS
®
3
Getting started!
Features and appearance will vary throughout this manual
Load Dishwasher
1
For best dishwashing results, follow the rack loading guidelines found in the Loading the dishwasher racks section. No pre-rinsing of
normal food soil is required. Scrape off hard soils, including bones, toothpicks, skins, and seeds. Remove leafy vegetables, meat trimmings,
and excessive amounts of grease or oil. Remove acidic food soils that can discolor stainless steel.
Add Detergent
2
Add needed amount of detergent to the detergent dispenser. Use a detergent such as Cascade Complete All-in-1 ActionPacs™. See Detergent
Dispenser in the Using the dishwasher section.
Add Rinse Agent
3
Add Rinse Agent to the rinse agent dispenser. See
Select Cycle
4
Press the Select Cycle pad for the desired wash cycle. The light next to the Select Cycle pad will be on to indicate which wash cycle has been
selected.
The cycle may be selected with the door in the open position. The cycle will not start until after the door is closed and Start selected.
AutoSense
(on some models)
This cycle automatically senses the soil level and adjusts the wash cycle accordingly.
Heavy This cycle is meant for heavily soiled dishes, cookware, pots, or pans with dried-on or baked-on soils.
Everyday dishes are safe to be used in this cycle.
Normal
NOTE: Normal was used to rate the energy efficiency of this dishwasher.
Light
This cycle is meant for normal everyday soil levels and is designed to conserve both water and energy.
This cycle is for light to medium soiled dishes. It is safe for china and crystal.
Use a Rinse Agent such as Cascade® Rinse Aid
™ in the Using the dishwasher section.
Rinse For rinsing partial loads that will be washed later. Do not use detergent. Detergent is not dispensed during the
(on some models) rinse cycle.
Select Options
5
The light by the selected pad will be ON to indicate which Option has been selected.
Wash Temp
This option increases the temperature to help clean heavily soiled dishes and may increase the overall cycle time.
Boost Option may be turned On or Off during the wash cycle.
(on some models)
Wash Temp This option raises the water temperature in the final rinse to sanitize your dishware. The cycle length will
Sani vary depending on the temperature of your inlet water.
(on some models) NOTE: This option is monitored for sanitization requirements. If the cycle is interrupted during or after the main
wash portion or if the incoming water temperature is so low that adequate water heating cannot be achieved,
the sanitizing conditions may not be met. In these cases, the Sanitized light will not illuminate at the end of the
cycle. Utilizing this option will modify the cycle to meet the requirements of Section 6, NSF 184 for soil removal
and sanitization efficacy.
NOTE: NSF certified residential dishwashers are not intended for licensed food establishments.
Heated Dry Shuts off the heat drying option. Dishes air dry naturally and energy is saved. Open the dishwasher door to
Off speed drying.
Heated Dry Turns on the heater for faster drying. This cycle may extend the time to your wash cycle up to 64 minutes. This
On
option is not available with the Rinse cycle.
4
GEAppliances.com
Select Options (Continued)
5
Steam For use with heavily soiled and/or dried-on, baked-on soils. This option MUST be selected PRIOR to
(Prewash) starting the cycle. The Steam option adds approximately 30 minutes to the cycle time. This option is
(on some models)
available with Heavy, Auto Sense, and Normal cycles.
Wash Selecting either the Upper or Lower Wash Zones will target dishwashing of just one rack. This will
Zones shorten the cycle time and conserve energy. This option can be used when there is only half a
(on some models)
load of dishes.
Delay Delays the start of a wash cycle up to 8 to 12 hours depending on model. Press Delay Hours, to select
Hours the number of hours, then press Start one time to begin countdown. The cycle will start once allotted time
(on some models) has expired.
Control You can lock the controls to prevent selections from being made. You can also lock the controls
Lock after you have started a cycle to prevent cycle changes.
start the dishwasher by pressing pads with this option selected.
To LOCK the dishwasher control, depending on the model, press and hold the Heated Dry pad for 3 seconds or
press and hold the Steam and Wash Temp pads at the same time for 3 seconds. The Control Lock light will turn
on to indicate the control is locked.
To UNLOCK the dishwasher control, depending on the model, press and hold the Heated Dry pad for 3 second
or press and hold the Steam and Wash Temp pads at the same time for 3 seconds. The Control Lock light
will turn off to indicate the control is unlocked.
For example, children cannot accidentally
Energy When connected to a smart meter and your electric company, the dishwasher will automatically delay starting
Smart a cycle during the more expensive peak demand times, and run when demand is low. However, you can override
the delay settings and use the dishwasher as needed. Learn more about Energy Smart under the Using the
Dishwasher section.
Start Dishwasher
6
Start Door can be open to select the desired options. Press the Start pad and close the door within 10 seconds
to start the cycle or begin the Delay Hours countdown. The wash cycle will begin shortly after closing
the door. If the door is open, the illuminated lights will turn off if a pad is not pressed within two minutes.
To activate the display, close and open the door or press any pad.
Interrupt To interrupt or pause a dish cycle, slowly open the door. Opening the door will cause the wash cycle to
or Pause pause. The dishwasher will beep every minute to remind you to close the door. To restart or resume
the cycle, press Start, and close the door.
Cancel To cancel a wash cycle, press and hold the Start pad for 3 seconds and close door. The dishwasher will drain,
emit a beep sound, and the wash cycle light will turn OFF.
Cycle Completion
7
Sanitized Displayed at the end of the cycle when Wash Temp Sani (Sanitize) has been selected and the dishwasher
has met the requirements for sanitization. See Wash Temp Sani, for complete option description.
Opening the door or pressing any key while the door is closed will turn off the light.
Clean Displayed when a wash cycle is complete. The light stays ON as a reminder that the dishes are clean.
the door or pressing any key while the door is closed will turn the light off.
Opening
5
Using the dishwasher.
Check the Water Temperature
The entering water should be at least 120°F (49°C) and
not more than 150°F (66°C) for effective cleaning and to
prevent dish damage. Check the water temperature with a
candy or meat thermometer. Turn on the hot water faucet
nearest the dishwasher, place the thermometer in a glass
and let the water run continuously into the glass until the
temperature stops rising.
Energy Smart
Energy Smart enables your dishwasher to reduce energy
consumption during periods of high energy costs. If you are
in an area where your electricity provider charges variable
rates at different times of the day, your dishwasher will
inform you of those times when you are paying the highest
rate. You can then either delay starting your dishwasher
until the rate goes down; or you can override the feature
and run your dishwasher at your convenience.
What you will need:
Smart Meter that will communicate with your
1
dishwasher. Consult your local electricity provider to
determine if the technology is available in your area.
An Energy Smart dishwasher model (GDF520, GDF540,
2
GDT530 or GDT550).
An Appliance Communication Module (ACM). Please
3
visit, gebrillion.com to order the communication device
that will need to be installed in the dishwasher.
Use a Rinse Agent such as Cascade® Rinse Aid™
Rinse agents, such as Cascade® Rinse Aid™ are designed for great drying action and protect against spots
and film build-up on your dishes, glasses, flatware, cookware, and plastic.
Filling the Dispenser
The rinse agent dispenser holds 3.5 oz. (100 ml) of rinse agent. Under normal
conditions, this will last approximately one month.
Make sure the dishwasher door is fully open.
1
Open the RINSE AID dispenser door.
2
Slowly add rinse agent until the fill cup is full. May need to pause several times to
3
allow rinse aid to settle.
Clean up any spilled rinse agent with a damp cloth.
4
Close the RINSE AID dispenser door.
5
Indicator
window
Rinse Aid Setting
The amount of rinse agent released into the final wash can be adjusted. The
factory setting is at the midpoint. If hard water spots appear on dishes, try a
higher setting. If you see foam in the dishwasher, move the indicator to a lower
setting.
To adjust the setting
Open the RINSE AID dispenser door; then turn the adjuster clockwise to
increase the amount of rinse agent, counterclockwise to reduce the amount of rinse agent.
Rinse
agent
adjuster
6
GEAppliances.com
Detergent Dispenser
The detergent dispenser is located in the center of
the dishwasher door. It has two compartments. The
main wash compartment is found inside the detergent
dispenser. To open, press the blue button on the side of
the dispenser. The pre-wash compartment is on the lid of
the detergent dispenser. Use the pre-wash compartment
only when your water is extremely hard or when you have
a heavy soiled load.
NOTE: Do not block detergent dispenser with large or tall
utensils.
Detergent
Dispenser
You may use tablet, powder, liquid or gel automatic
dishwasher detergent. Make sure you use only detergents
specifically labeled for use in automatic dishwashers. Never
use liquid hand dish detergent in an automatic dishwasher.
Sudsing and poor wash performance will result with the use of
improper detergents.
Detergents should be stored in a dry location and in their
original container to prevent loss of effectiveness. Place
detergent in the cup just prior to starting the dishwasher and
then close the cover. The cover will open during the wash
cycle.
Number of
Grains/Gal.
Less than 4 Fill cup to 1/3 full
4 to 8 Fill cup to 2/3 full
8 to 12 Fill cup completely full
Greater than 12
Main
Wash
Pre-Wash
Push/Slide
to Close
Using too much detergent with very soft and/or very
hot water may cause a condition called etching on your
glassware. Etching is a permanent cloudiness in your
glassware. This condition is irreversible. However, using too
little detergent will cause poor wash performance.
Use the table as a starting point and then adjust the amount
of detergent you use. Use just enough to get good wash
performance. Using just the right amount of detergent will
provide great wash performance without wasting detergent
or etching of glassware.
Detergent Cups to Fill
Fill both main wash cup and pre
wash cup
Rinse Agent
Filling the Detergent Dispenser
GE recommends using detergent in tablet or packet form.
Independent testing has shown this form of detergent is very
effective in the dishwasher.
are an example of this type of detergent. Simply put a tablet
or packet into the main wash compartment and slide to
close the detergent cup cover. Please notice that the tablet or
packet must be placed in the main wash compartment of the
detergent cup. If the tablet or packet is tossed in the bottom of
the dishwasher, the detergent will be flushed down the drain
in a very short period of time and will thus be wasted. Wash
performance will be very poor as a result.
If you choose to use detergent in powder, liquid or gel form,
the amount of detergent you use will be determined by the
hardness of your water, the temperature of your water, and
the food soil load inside the dishwasher. Contact your water
company to get information about the hardness of the water
in your area. Water hardness is measured in grains per gallon.
Use this information and the table above to determine the
amount of detergent to use. You may purchase a hard water
test strip from GE. Call 1-877-959-8688 and ask for part
number WD01X10295. In Canada, call 1-800-661-1616
Cascade® All-in-1 ActionPacs™
DO NOT USE HAND DISH DETERGENT
NOTE: Using a detergent that is not specifically designed
for dishwashers will cause the dishwasher to fill with suds.
During operation, these suds will spill out of the dishwasher
vents, covering the kitchen floor and making the floor wet.
Because so many detergent containers look alike, store the
dishwasher detergent in a separate space from all other
cleaners. Show anyone who may use the dishwasher the
correct detergent and where it is stored.
While there will be no lasting damage to the dishwasher, your
dishes will not get clean using a dishwashing detergent that is
not formulated to work with automatic dishwashers.
7
Loading and place settings.
For best dishwashing results, follow these loading guidelines. Features and appearance of racks and silverware
baskets may vary from your model.
To add flexibility in loading, the utility shelf (on some
models) may be placed in the up or down position.
The shelf may also be used to secure stemware such
as wine glasses. Because these stemware items
come in various sizes, slowly push the rack in to
ensure the items do not bump into the edges of the
dishwasher, which may cause damage to the items.
It is important to ensure that items do not protrude
through the bottom of the rack or silverware basket
(on some models) where they will block the rotation
of the middle spray arm. This could result in noise
during operation and/or poor wash performance.
Check to make sure
that no items will block
rotation of the wash
arms.
End Cap
Rail
Rollers
Upper Rack
The upper rack is primarily for glasses, cups, and
saucers. However, other items such as pots, pans,
and plates may be placed in the upper rack. This is
also a secure place for dishwasher-safe plastic items.
The upper rack can be used for odd sized utensils.
Sauce pans, mixing bowls, and other similarly shaped
items should be placed face down for best wash
performance. Ensure small plastic items are secure
so that they cannot fall into the heater at the bottom
of the dishwasher, potentially damaging the item.
On some models, the upper rack may be adjusted
to accommodate larger items. To adjust the upper
rack, fully extend the upper rack and remove the two
plastic end caps on the front of the rails. Remove the
upper rack. Select the set of rollers on the side of the
rack that provides the desired height, and reinstall
the upper rack by guiding the rack rails between the
appropriate set of rollers. With the rack reinstalled,
replace the two plastic end caps, ensuring the snap
is properly engaged. Failure to properly engage
the end caps may result in the rack falling from the
dishwasher.
Upper Rack - 8 Place Settings GDF510 & GDF520
Upper Rack - 8 Place Settings GDT530, GDF540 & GDT550
Upper Rack - 10 Place Settings GDF510 & GDF520
Upper Rack - 10 Place Settings GDT530, GDF540 & GDT550
Upper Rack - 12 Place Settings GDF510 & GDF520
Upper Rack - 12 Place Settings GDT530, GDF540 & GDT550
8
8
GEAppliances.com
Lower Rack
Fold down tines (on some models) allow for greater
flexibility in loading large items. Select the position
of the fold down tine that best accommodates
your dishware items. The direction of the fold down
tines can be changed to match preferred loading
direction. To adjust the fold down tine direction,
remove the clips securing the fold down tines to the
racks by sliding the clip so that it disengages from
the rack wire. The fold down tines may be rotated
in the opposite direction to reverse the loading
direction. Secure the fold down tines to the rack
using the same clips. The clip is removed by pulling
up on the clip and separating it from the rack.
Replace the clip on the opposite side of the rack by
positioning the clip over the wire and pressing down.
It is important to ensure that items do not protrude
through the bottom of the rack or the silverware
basket where they will block the rotation of the lower
spray arm. This could result in noise during operation
and/or poor wash performance.
Clip
The lower rack is best used for plates, saucers and
cookware items. Large items, such as broiler pans
and baking racks should go along the sides of the
rack. If necessary, oversized glasses and mugs can
be placed in the lower rack to maximize loading
flexibility. Plates, saucers and similar items should be
placed between the tines in the direction that allows
the item to remain secure in the rack.
Do not load large items where they may block the
detergent dispenser when the door is closed.
The reversible tine blocks (on some models) are
designed to allow greater flexibility in loading dishes.
The direction of the tine blocks can be changed to
match preferred loading direction. To adjust the tine
block direction, remove the clips securing the tine
blocks to the racks by pulling up on the tab, then
flex the retaining wire to unseat the tine block from
the lower rack. The tine block may be turned in the
opposite direction to reverse the loading direction.
Secure the tine block to the rack using the same
process and be sure to snap the same clips in place.
Lower Rack - 8 Place Settings GDF510 & GDF520
Lower
Rack - 8 Place Settings -
GDT530, GDF540 & GDT550
WARNING! The clips can be a
choke hazard for small children. Keep out of
reach of children.
Lower Rack - 10 Place Settings GDF510 & GDF520
Lower
Rack - 10 Place Settings -
GDT530, GDF540 & GDT550
Lower Rack - 12 Place Settings - GDF510 & GDF520
Lower
Rack - 12 Place Settings -
GDT530, GDF540 & GDT550
9
Loading the silverware baskets…
For best dishwashing results, follow these loading guidelines. Features and appearance of racks and silverware
baskets may vary from your model.
The accessory basket (on some models) may be
positioned by placing the hooks on the back of the
basket over the top wire on the sides of the lower
rack.
The FlexBaskets (on some models) may be positioned
on the front of either the upper or lower racks.
Secure the basket to the rack using the wire loop on
the front of the upper and lower racks to engage the
tabs on the rear of the basket.
Do not load large or tall utensils where they may
block the detergent dispenser or become trapped
between the door and the gasket when the door is
closed.
Mounting
Bosses
Silverware
Basket
Silverware
Basket
Wire Loops
Silverware Basket
Place flatware in the removable silverware and
accessory baskets (on some models). Sharp objects,
such as forks and knives, may be placed with the
handles facing up, in order to protect your hands.
For the best wash performance, place other items
such as spoons with the handles facing down. Avoid
allowing items to nest together, which may keep
them from being properly washed. When loading,
distribute items evenly in the basket.
The silverware and accessory baskets (on some
models) may also be used for small items, such as
measuring spoons, baby bottle nipples, plastic lids,
or corn cob holders. The silverware basket covers (on
some models) can be closed to contain small items.
The door mounted silverware basket (on some
models) may be positioned either on the door by
securing the basket to the door using the two
mounting bosses, or to the rack by securing the
basket to the rack using the wire loop on the front of
the lower rack to engage the tabs on the rear of the
basket.
Silverware Basket - 8 Place Settings GDF510 & GDF520
Silverware Basket
GDT530, GDF540 & GDT550
- 8 Place Settings -
Silverware Basket - 10 Place Settings GDF510 & GDF520
Silverware Basket
GDT530, GDF540 & GDT550
- 10 Place Settings -
Silverware Basket - 12 Place Settings GDF510 & GDF520
Silverware Basket
GDT530, GDF540 & GDT550
- 12 Place Settings -
10
Care and cleaning. GEAppliances.com
Cleaning the Exterior Door Panel
Before cleaning the front panel, make sure you know
what type of panel you have. Refer to the last two
letters of your model number. You can locate your
model number on the left-hand tub wall just inside
the door. If your model number ends with BB, CC,
WW, SA or ES then you have a painted door panel. If
your model number ends with SS, then you have a
Stainless Steel Door panel. If your model number ends
with II, then you have an Integrated door panel.
Follow the instructions below for cleaning the door
panel for your specific model.
Painted Door Panel (model numbers ending in BB–
black, CC–bisque, WW–white, SA-silver or ES-slate)
Use a clean, soft, lightly dampened cloth, then dry
thoroughly. You may also use a good appliance wax
or polish.
Cleaning the Control Panel
To clean the control panel, use a lightly dampened soft
cloth. Then dry thoroughly.
Stainless Steel Inner Door
The stainless steel used to make the dishwasher tub
and inner door provides the highest reliability available
in a GE dishwasher.
Stainless Steel Door Panel (model numbers ending in
SS)
The stainless steel panels can be cleaned with
Stainless Steel Magic or a similar product using a clean,
soft cloth. Do not use appliance wax, polish, bleach or
products containing chlorine on Stainless Steel doors.
You can order Stainless Steel Magic #WX10X29
through GE Parts by calling 877.959.8688. In Canada,
call 1-800-661-1616.
Integrated Door Panel (model numbers ending in II)
This is a custom installed door panel, and you
will need to refer to the cabinet manufacturers
recommendations for proper cleaning.
Do not use scouring pads or powered cleaners
because these products can scratch the finish.
If the dishwasher tub or inner door should be
scratched or dented during normal use, they will
not rust or corrode. These surface blemishes will
not affect their function or durability.
Fine
Filter
Ultra-Fine
Filter
Cleaning the Filters
Inspect the filters periodically, every other month or so depending on usage, and clean if necessary. If there is a
decrease in wash performance or dishes feel gritty, this is also an indication the filters need to be cleaned.
Retaining Posts
Spray Arm
Ultra-Fine Filter
To clean the Ultra-Fine Filter,
remove the bottom rack. Twist and
remove the large round filter. Rinse
filter with warm soapy water and
use a sponge to carefully remove
any stubborn particles. Scrubbing
with scouring pads or brushes can
damage the filter. Once cleaned,
replace the Ultra-Fine Filter, and
twist to lock in place.
Fine Filter
To clean the Fine Filter (mesh plate), remove the
bottom rack. Remove the Ultra-Fine Filter. Twist
each of the two retaining posts located toward the
back bottom of the tub, and remove the Fine Filter.
Rinse filter with warm soapy water. Scouring pads
or brushes can damage the filter but a soft brush or
sponge may be needed to remove stubborn soils or
calcium deposits caused by hard water. Once cleaned,
replace the Fine Filter, the Ultra-Fine Filter, and twist
the two retaining posts into place.
WARNING! The retaining posts can
Protect Against Freezing
If your dishwasher is left in an unheated place during
the winter, ask a service technician to:
Cut off electrical power to the dishwasher.
1
Remove fuses or trip circuit breaker.
Turn off the water supply and disconnect the
2
water inlet line from the water valve.
be a choke hazard for small children. Keep out of
reach of children.
Drain water from the water inlet line and water
3
valve. (Use a pan to catch the water.)
Reconnect the water inlet line to the water valve.
4
Air gap
Check the air gap any
time your dishwasher
isn’t draining well.
Does Your Dishwasher Have an Air Gap?
An air gap protects your dishwasher against water
backing up into it if a drain clogs. The air gap is not
a part of the dishwasher. It is not covered by your
warranty. Not all plumbing codes require air gaps,
so you may not have one.
The air gap is easy to clean.
Turn off the dishwasher and lift off the cover.
1
Remove the plastic cap and clean with
2
a toothpick.
11
Before you call for service…
Troubleshooting Tips
Save time and money! Review the charts on the following pages, or visit GEAppliances.com.
In Canada visit www.GEAppliances.ca. You may not need to call for service.
Problem
Start Status The door was opened or the • Press the Start pad once to start the dishwasher. Press the
indicator light flashing cycle was interrupted. Start pad a second time when the dishwasher is running only if you
wish to cancel the cycle.
Dishwasher BEEPS This is a reminder that your • Press Start and close the door.
once every minute dishwasher door has been left
open during operation. It will
continue beeping until you press
Start and close the door.
Beeping at the end This is normal. The dishwasher • To turn off the double beep indicator (or re-activate it if it was previously
of the cycle will beep twice at the end of the turned off), press the Heated Dry pad 5 times within 3 seconds.
(on some models) cycle. A triple beep will sound to indicate the end-of-cycle beep option
has been turned on or off.
Dishes and flatware Ultra fine or fine filter is clogged • See the Care and cleaning section.
not clean Low inlet water temperature • Make sure inlet water temperature is correct (see the Using the dishwasher
section). Turn on the hot water faucet nearest the dishwasher, let run until
the water temperature stops rising. Then start the dishwasher and turn
off the faucet. This ensures the entering water is hot. Select Wash Temp Boost if
available.
Water pressure is temporarily low • Turn on a faucet. Is water coming out more slowly than usual? If so, wait
until pressure is normal before using your dishwasher.
Air gap or disposer is clogged • Clean the air gap or flush the disposer.
Improper rack loading • Make sure large dishware does not block the detergent dispenser or the
wash arms. See the Loading the dishwasher racks section.
• When large utensils are placed in the silverware basket, do not mount the basket
on the door (on some models). Instead, mount basket on the lower rack.
Poor performing detergent • Use a highly rated detergent such as Cascade Complete
Spots and filming Extremely hard water • Use rinse agents such as Cascade ® Rinse Aid™ to remove spots
on glasses and and prevent new film buildup.
flatware
Low inlet water temperature • Make sure water temperature is at least 120°F.
Overloading or improper • Load dishwasher as shown in the Loading Place Settings section.
loading of the dishwasher
Old or damp powder detergent • Make sure detergent is fresh.
Rinse agent dispenser empty • Refill with rinse agent such as Cascade ® Rinse Aid™.
Too little or low performing • Make sure you use the proper amount of highly rated detergent.
detergent
Possible Causes What To Do
• If water is extremely hard, a softener may be required.
®
All-in-1 ActionPacs™.
12
GEAppliances.com
Problem Possible Causes What To Do
Cloudiness on Combination of soft water and • This is called etching and is permanent. To prevent this from happening,
glassware too much detergent use less detergent if you have soft water. Wash glassware in the shortest
cycle that will get it clean.
Low performing phosphate • See A white film on glassware, dishware and the interior in this
free detergent Troubleshooting section.
Water temperature entering the • This could be etching. Lower the water heater temperature.
dishwasher exceeds 150°F (66°C)
Suds in the tub Correct detergent • Use only automatic dishwasher detergents to avoid sudsing. Cascade®
wasn’t used Automatic Dishwashing Detergents have been approved for use in all
GE dishwashers.
• To remove suds from the tub, open the dishwasher and let suds dissipate.
Pump out water by pressing Start and close the door. Wait 30 seconds.
Open the door, press and hold Start for 3 seconds, and close the door.
Repeat if necessary.
Rinse agent was spilled • Always wipe up rinse agent spills immediately.
Detergent left in Dishes or utensils are blocking • Reposition the dishes, so the water from the lower spray arm can flush
dispenser cups the detergent cup the detergent cup. See the Loading the dishwasher racks section.
• Reposition the tall utensils or heavy silverware that may be keeping the
dispenser cup door from opening. See the Loading the silverware basket
section.
Black or gray Aluminum utensils have • Remove marks with a mild, abrasive cleaner.
marks on dishes rubbed against dishes
Dishes don’t dry Low inlet water temperature • Make sure inlet water temperature is at least 120°F.
• Select Heated Dry.
• Use Wash Temp Boost option.
• Select a higher cycle, such as Wash
Rinse agent dispenser is empty • Check the rinse agent dispenser and fill as required.
Control panel responded Door may not be completely • Make sure the door is firmly closed.
to inputs but dishwasher closed
never filled with water
Water valve may be turned off • Make sure water valve (usually located under the sink) is turned on.
Stained tub interior Some tomato-based foods can • Use of the Steam cycle (on some models) after adding the dish to the load
cause reddish stains can decrease the level of staining.
Tea or coffee stains • Remove the stain by hand, using a solution of 1/2 cup bleach and
3 cups warm water. NOTE: Do not use bleach on stainless steel
tub or inner door.
Temp Sani (
Sanitize) or Heavy.
Before cleaning interior, wait at least 20 minutes after a cycle for the
heating elements to cool down. Failure to do so can result in burns.
:KLWHILOPRQLQVLGHVXUIDFH³ • GE recommends Cascade ® Rinse Aid™ to help prevent hard water
hard water minerals mineral deposits from forming.
• Run dishwasher with citric acid to remove mineral deposits. Citric acid
(Part number: WD35X151) can be ordered through GE Parts. See back
cover for ordering information.
Dishwasher won’t run Fuse is blown or circuit breaker • Replace fuse or reset circuit breaker. Remove any other appliances from
is tripped the circuit.
Power is turned off • In some installations, the power to the dishwasher is provided through a
wall switch, often located next to the disposer switch. Make sure it is on.
Control panel is locked • Unlock control panel. See the Getting started section.
An overall yellow or brown film can
be caused by iron deposits in water
• A special filter in the water supply line is the only way to correct
this problem. Contact a water softener company.
CAUTION!
13
Before you call for service…
Problem Possible Causes What To Do
Control panel lights Time too long between • Each pad must be touched within 30 seconds of the others.
go off when you’re touching of selected pads To relight, touch any pad again or open the door and
setting controls unlock (top control).
Water standing in Air gap is clogged • Clean the air gap. See the Care and cleaning section.
the bottom of the tub
Water won’t pump Drain is clogged • If you have an air gap, clean it. See the Care and cleaning section.
out of the tub
• Check to see if your kitchen sink is draining well. If not, you
may need a plumber.
Steam This is normal • Warm, moist air comes through the vent during drying and when
water is being pumped out. This is necessary for drying.
Sanitized light does The door was opened and the • Do not interrupt the cycle by opening the door during the wash cycle.
not illuminate at the cycle was interrupted during
end of the cycle final rinse
The incoming water • Raise the water heater temperature to between 120°F and 150°F.
temperature was too low
Noise Normal operating sounds: • These are all normal. No action is required.
Detergent cup opening
Water entering dishwasher
The motor stops and starts at
various times during the cycle
Spray arms start and stop at
various times
Drain pump sounds during
pump out
Drain pump starts and stops
several times during each drain
Rattling dishes when the spray • Make sure dishes are properly loaded. See the Loading the
arm rotates dishwasher racks section.
Rattling silverware against door • Tall utensils may be placed in the upper rack to avoid bumping against
during wash inner door during wash cycle.
A white film on This problem caused by • To remove the white film, run your dishes through a dishwasher cycle with
glassware, dishware phosphate-free dishwasher citric acid. Use a WD35X151 citric acid kit found online.
and the interior detergent Pour the citric acid in the detergent cup and close the cover. Place the filmed
but otherwise clean glassware and dishware in the dishwasher. Leave
silverware and other metal items out of the dishwasher. Turn the dishwasher
on and let it run through a complete cycle without detergent. The glassware,
dishware, and dishwasher should come out film free. Alternatively,
a vinegar rinse may be used. Pour 1 cup of vinegar into dishwasher just after
the detergent cup opens and let the dishwasher complete its cycle.
This may be repeated several times a year as needed
The use of a rinse agent such as Cascade
a repeat build up of film. Also, the use of a highly rated detergent such as
Cascade Complete
• If the dishwasher drains into a disposer, run disposer clear.
®
Rinse Aid™ may help minimize
®
All-in-1 ActionPacs™ will help prevent film build-up.
14
GE Dishwasher Warranty. GEAppliances.com
All warranty service provided by our Factory Service Centers, or an
®
authorized Customer Care
technician. To schedule service, visit us on-line
at GEAppliances.com, or call 800.GE.CARES (800.432.2737) in the United
States. In Canada, call 1.800.561.3344. Please have serial number and
model number available when calling for service.
Staple your receipt here.
Proof of the original purchase
date is needed to obtain service
under the warranty.
Servicing your appliance may require the use of the onboard data port for diagnostics. This gives a GE
Factory Service technician the ability to quickly diagnose any issues with your appliance and helps GE
improve its products by providing GE with information on your appliance. If you do not want your appliance
data to be sent to GE, please advise your technician NOT to submit the data to GE at the time of service.
For The Period Of: GE Will Replace:
One Year Any part of the dishwasher which fails due to a defect in materials or workmanship. During
From the date of the this limited one-year warranty, GE will also provide, free of charge, all labor and in-home
original purchase service to replace the defective part.
What GE Will Not Cover (for customers in the United States):
Service trips to your home to teach you how to use
the product.
Improper installation, delivery or maintenance.
Failure of the product if it is abused, misused, or used for
other than the intended purpose or used commercially.
Replacement of house fuses or resetting of circuit breakers.
Product not accessible to provide required service.
Damage to the product caused by accident, fire, floods
or acts of God.
Incidental or consequential damage caused by possible
defects with this appliance.
Cleaning or servicing of the air gap device in the drain line.
Damage caused after delivery, including damage from
items dropped on the door.
(;&/86,212),03/,(':$55$17,(6³<RXUVROHDQGH[FOXVLYHUHPHG\LVSURGXFWUHSDLUDVSURYLGHGLQWKLV/LPLWHG
Warranty. Any implied warranties, including the implied warranties of merchantability or fitness for a particular purpose,
are limited to one year or the shortest period allowed by law.
This warranty is extended to the original purchaser and any succeeding owner for products purchased for home use within the USA.
If the product is located in an area where service by a GE Authorized Servicer is not available, you may be responsible for a trip charge
or you may be required to bring the product to an Authorized GE Service location for service. Proof of original purchase date is needed
to obtain service under the warranty. In Alaska, the warranty excludes the cost of shipping or service calls to your home.
Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal
rights, and you may also have other rights which vary from state to state. To know what your legal rights are, consult your local or
state consumer affairs office or your state’s Attorney General.
Warrantor: General Electric Company. Louisville, KY 40225
What Is Not Covered (for customers in Canada):
Service trips to your home to teach you how to use
the product.
Improper installation.
If you have an installation problem, contact your dealer
or installer. You
electrical, exhausting and other connecting facilities.
(;&/86,212),03/,(':$55$17,(6³<RXUVROHDQGH[FOXVLYHUHPHG\LVSURGXFWUHSDLUDVSURYLGHGLQWKLV/LPLWHG
Warranty. Any implied warranties, including the implied warranties of merchantability or fitness for a particular purpose,
are limited to one year or the shortest period allowed by law.
are responsible for providing adequate
Failure of the product if it is abused, misused, or used for
other than the intended purpose or used commercially.
Replacement of house fuses or resetting of circuit breakers.
Damage to the product caused by accident, fire, floods
or acts of God.
Damage caused after delivery.
This warranty is extended to the original purchaser and any succeeding owner for products purchased in Canada for home use within
Canada. In home warranty service will be provided in areas where it is available and deemed reasonable by Mabe to provide.
WARRANTOR IS NOT RESPONSIBLE FOR CONSE QUEN TIAL DAMAGES.
Warrantor: MC Commercial, Burlington, ON, L7R 5B6
15
Loading...