GE ABH2 Installation Guide

GE
Lighting
AlbeoTM LED Luminaire
Modular High & Low Bay Lighting (ABH2-series)
Features
• 5 year warranty
BEFORE YOU BEGIN
Read these instructions completely and carefully.
Installation Guide
WARNING/AVERTISSEMENT
RISK OF ELECTRIC SHOCK
• Turn power off before inspection, installation or removal.
• Properly ground electrical enclosure.
RISK OF FIRE
• Follow all NEC and local codes.
• Use only UL or IEC approved wire for input/output connections. Minimum size 18 AWG.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAN ICES-3 (A)/NMB-3(A)
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
RISQUES DE DÉCHARGES ÉLECTRIQUES
• Coupez l’alimentation avant d’’inspecter, installer ou déplacer le luminaire.
• Assurez-vous de correctement mettre à la terre le boîtier d’alimentation électrique.
RISQUES D’INCENDIE
• Respectez tous les codes NEC et codes locaux.
• N’utilisez que des ls approuvés par UL ou IEC pour les entrées/sorties de
connexion. Taille minimum 18 AWG.
Save These Instructions
Use only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer.
Prepare Electrical Wiring
Electrical Requirements
• The LED driver must be supplied with 120-480 VAC, 50/60 Hz per product label and connected to an individual properly grounded branch circuit, protected by a 15 or 20 ampere circuit breaker.
Grounding Instructions
• The grounding and bonding of the overall system shall be done in accordance with National Electric Code (NEC) Article 600 and local codes.
imagination at work
Unit Installation
Carefully unpack unit and properly inspect for defects before installing. Wear work gloves to prevent dirt and oil from being
1
transferred to the luminaire.
Choose a mounting method: chain or cable, rod mount, or pendant mount . (Chain or cable is covered here. Other options are
2
covered in the section Optional Mounting Methods).
Fixture Weight
ABH2-series
LED Modules
1 13 17 2 17 21 3 31 40 4 36 43 6 58 70
Chain or Cable Mounting: Please
3
follow all UL, NEC and minimum load rating guidelines when selecting and installing a cable or chain.
NOTE: When selecting chain, a joint in a circular chain link shall be welded. A joint in a chain link of another shape shall not be located within 30 degrees of the vertical unless welded.
Max. Weight (lbs.)
120/277V 347/480V
Direct Mounting: Hang two chains/
4 5
cables from a structural member of the ceiling. Fixture must be supported independently of an outlet box. Tighten adjustment screws on all four mounting inserts, then attach chain or cable to mounting inserts on both ends of
xture.
Electrical Connections (120/277V)
Attach to structural member
Mounting inserts
Tighten screws
Attach to structural member
Indirect Mounting for Uplighting:
Hang two chains/cables from a structural member of the ceiling. Fixture must be supported independently of an outlet box. Attach chain or cable to eye bolt
mounts on both ends of xture.
Loosen screws to remove endcap.
1
A) Conduit
Option: power input from side – Remove knockout in
3 4
endcap and A) Install 1/2” conduit, or B) install AC power cord with strain relief. Plug unused hole on top with
appropriate tting.
B) Power cord
A) Conduit
Option: power input from top – A) Install 1/2” conduit, or
2
B) install AC power cord with strain relief.
Connect the green (ground), black (line) and white (neutral) wires of the AC line to the similarly colored
wires of the xture’s power supply using UL listed
wire connectors. Re-attach endcap.
B) Power cord
Electrical Connections (347/480V)
A) Conduit B) Power cord
Loosen screws to remove endcap.
1
Connect AC line to xture’s power supply using UL listed
3 4
wire connectors. Green to green (ground), red to black (line) and black to white (neutral).
Optional Mounting Methods
A) Install 1/2” conduit, or B) install AC power cord with
2
strain relief.
Re-attach endcap.
OPTION A
Attach two rod mount brackets to xture using four
1 2
10-32 x 3/8” pan head screws per bracket.
Rod Mount Kit
Attach to structural member
Fasten with nuts
Secure 1/2” threaded rods into structural members in
ceiling. Place a nut on each threaded rod where xture should hang. Slide xture onto threaded rods and tighten second nut onto rods to secure xture.
OPTION B
NOTE: Pendant Mount Kit cannot be used with the 6‐module xture.
Pendant Mount Kit
AC line
Attach pendant mount bracket assembly to four
1
mounting inserts on the xture with (8) 10‐32 x 3/8”
Philips pan head screws.
Align tabs
Slide top plate into main bracket. Align top tabs of end
3
plate with slots in main bracket and push endplate into place.
Attach top plate to 3/4” conduit and pass AC input wires
2
through conduit, top plate, and locking nut (if used).
Connect the AC input wires to the xture wires coming
from the strain relief in the main bracket assembly bottom plate.
Fasten screws
Fasten endplate to bracket with a 8-32 x 1/4” Philips pan
4
head screw. Fasten endplate to mounting hub with a 6-32 x 1/2” hex head screw.
Troubleshooting
Symptom Solution
Luminaire will not turn on. • Check that the color of the supply side wires match the color of the wires they are connected to.
• Check that all wire connectors are properly connected.
• Verify that your input voltage is within specs.
• If you are using any additional controls IE wireless controls // motion sensors, please also verify that those are working properly and that the unit is setup to interface with the controllers.
Mounting insert slides from side to side.
Endplate of Pendant Mount Kit does not snap in place.
• Check that the mounting insert is properly tightened using the adjustment screws provided.
• Check that the top plate is properly slotted in main bracket.
• Check that endplate tabs are properly aligned in pendant mount bracket assembly.
• Check that endplate is pushed rmly into place.
GE Lighting • 1-888-MY-GE-LED (1-888-69-43-533) • www.gelighting.com
GE Lighting, LLC is a subsidiary of the General Electric Company. The GE brand, logo, and Albeo are trademarks of the General Electric Company.
© 2013 GE Lighting, LLC. Information provided is subject to change without notice. All values are design or typical values when measured under laboratory conditions.
ALB014-012114
Loading...