GE 98504 User Manual

98504

Wireless Laser Notebook Mouse

Instruction Manual

For technical support contact Jasco Products at 1-800-654-8483 or

www.jascoproducts.com

TABLE OF CONTENTS

Package Contents ............................................................................................2

System Requirements ....................................................................................2

Battery Installation .......................................................................................... 3

Mouse Installation ............................................................................................ 3

Reconnecting the Mouse to the Receiver ............................................ 4

Using the Laptop Clip .................................................................................... 4

Mouse Suite Software .................................................................................... 5

Troubleshooting ................................................................................................ 9

5 Year Limited Warranty .............................................................................10

FCC & FDA Statement ..................................................................................10

Package Contents

• Wireless Laser Notebook Mouse

• Laptop Clip

• 1 AA Battery

• Instruction Manual

• Mini USB Receiver

System Requirements

• Windows® 98 SE or higher, Mac OSX

• Available USB Port

2

Battery Installation

1. Press the battery release button on top of the mouse.

2. The battery door will open.

3. Insert 1 AA battery, being sure to match the polarity
of the batteries with the polarity markings inside the
battery compartment.

4. Close the battery door.

Mouse Installation

1. Slide the USB Receiver out of the bottom of the mouse.

2. Once the receiver has been removed, the Battery Meter
will light up.

Green Light = battery life is good.

Red Light (Blinking slowly) = battery is low.

Red Light (Blinking rapidly) = change battery.

3. Insert the USB receiver into an available USB port.
The receiver has an LED on the top.

Green Light on Receiver = Mouse movement.

Red Light on Receiver = Low battery.

4. Please refer to page 5 of this manual for the
Mouse Suite Installation.

LED

Battery Light

3

Reconnecting the Mouse to the Receiver

This mouse will usually automatically connect to the receiver. If needed,
you can connect the mouse to the receiver by following these steps.

1. Press the button on top of the receiver. The LED will light up on
the receiver.

2. Press the button on the bottom of the mouse. It is located near the top
of the mouse, left side.

3. The LED on the receiver will blink and you are fi nished.

Storing the Receiver

To help conserve battery and increase portability you
may store the receiver under the mouse. To do this,
simply unplug the receiver from your USB slot and
place it in the designed position on the bottom of the
mouse. Once the receiver is correctly in place, the power
will automatically shut off.

Using the Laptop Clip

Your mouse is equipped with the Laptop Clip. This is used for easy storage
of the mouse while on the go with your laptop. To use this clip, simply insert
the clip on the bottom of the mouse then place your mouse into the modem
slot on your laptop. Please ensure that your modem slot is not in use before
attaching the storage clip.

4

Mouse Suite Software (for Windows® Vista, XP & 2000 only)

The Mouse Suite is a software program with many features that give
amazing functionality to your GE mouse. Here is a brief overview.

Installation Procedure

1. Insert the Installation CD into the computer CD drive.

2. Run the fi le named “Setup”.

3. Follow the instructions on the screen.

4. Click Finish when completed.

Buttons Tab

From this screen you can set the function of each button on your mouse.
There are over 33 functions to choose from. To specify the function of each
button follow these steps:

5

1. Select the button you
want from the Button
drop down menu.

2. Next select the function
you want by using the
Function drop down
menu.

3. After you have selected
the features you want
click apply at the bottom
of your screen.
You may change these
features at any time.

You may also check your battery life from this screen. The battery indicator is
located on the right side of the window.

Magnifi er Function

This feature allows you to
use the scroll button as a
magnifi er. To enable this
feature, simply check the
box labeled “Magnifi er”
and click Apply. Press the
middle scroll button to
activate the magnifi er.
To make the magnifi er size
taller, press and hold the
scroll button again and
move the mouse up or down.
To make the magnifi er size wider, move the mouse right or left.

6

Double-Click Tab

This screen allows you to
set the double-click speed
of your mouse. Use the
slider to set the desired
speed. You must click
Apply to update any
changes.

Orientation Tab

This feature allows you to
set the orientation of the
mouse while fi nding the
most comfortable position
to hold the mouse.
Please follow the directions
on the screen to set the
orientation.

7

Wheel Tab

This screen allows you to
select different wheel
operations. You may
select vertical scrolling
speed as well as horizontal
scrolling speed. If you
would like to reverse the
scrolling direction of the
mouse, please check the
box labeled Reverse
Scrolling Direction.

Pointer Utility Tab

From this screen you can
select different functions
for the pointer.

8

Pointer Wrap

The pointer wrap feature allows the pointer to go in one side of the screen
and come out of the opposite side. This works at both sides of the screen
as well as top and bottom. This allows easier and more functional mouse
navigation with less wrist and arm movement.

Slow Motion

This feature allows the pointer to move in slow motion by pressing the Shift
key. This will help the precision of the pointer.

X-Focus

This feature allows you to make an inactive window active by simply moving
the pointer over the title bar.

Troubleshooting

• Mouse does not work properly

- Check the battery life on your mouse. If it is low please install new batteries.

- Reconnect your mouse to the receiver. Press the link button on the receiver.
Press the link button on the bottom of your mouse. (page 4)

• Mouse does not move on screen.

- Reconnect your mouse to the receiver.

- Change the batteries on your mouse.

- Make sure that your USB receiver is completely plugged into the
computer’s USB port .

Questions? Please call 1-800-654-8483 (option #4)
Monday—Friday, 9:00 am—5:00 pm CST.

9

Five Year Limited Warranty

Jasco Products Company warrants this product to be free from
manufacturing defects for a period of fi ve years from the original date of
consumer purchase. This warranty is limited to the repair or replacement
of this product only and does not extend to consequential or incidental
damage to other products that may be used with this unit. This warranty is
in lieu of all other warranties express or implied. Some states do not allow
limitations on how long an implied warranty lasts or permit the exclusion or
limitation of incidental or consequential damages, so the above limitations
may not apply to you. This warranty gives you specifi c rights, and you may
also have other rights which vary from state to state. If unit should prove
defective within the warranty period, return prepaid with dated proof of
purchase to:

Jasco Products Company
10 East Memorial Dr
Oklahoma City, OK 73114

FCC Statement

Notice: Federal Communications Commission (FCC) requirements, Part 15

This equipment has been tested and found to comply with the limits for a
class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

10

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

CAUTION: Any changes of modifi cations not expressly approved by
the grantee of this device could void the users authority to operate the
equipment. This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

FDA Notice

This product complies with DHHS Rules 21CFR Chapter I, Sub chapter J.
This product has been designed and manufactured according to IEC60825-1
on the safety label of laser product.

Class 1 Laser Product
It is recommended not to point directly in the eye or any other optical device.

CLASS 1 LASER

11

Distributed for GE

by Jasco Products Company

10 E. Memorial, Oklahoma City, OK 73114

www.jascoproducts.com