GE 45146 User Manual

Wireless Alarm System

Wireless
Keypad

User’s Manual

1 2

3 4

Choice

Choice

ALERT

ALERT

Control all sensors, accessories
and remote transmitters from
one location

™

™

3

Table of Contents

Important Safeguards 4

Introduction 5

Assigning a Wireless Keypad to a Device Location 6

Programming Security Codes into 7
the Wireless Keypad

Changing the Master Code or either 7
Alternate User Code

Erasing Alternate User Codes 8

Placement of the Wireless Keypad 9

Mounting the Wireless Keypad on a Wall 10

Removing Top Cover from the Mounting Plate 11

Attaching Top Cover to Mounting Plate 11

Operating the Wireless Keypad 11

Using the Panic Button 12

Replacing a Wireless Keypad 12

Erasing a Wireless Keypad from a Control Center 13

Low Battery Indicator/Replacing the Battery 13

Resetting Master Code 14

Battery Warnings 15

F.A.Q.'S 16

FCC Warning 17

2

Before connecting or operating the Wireless Keypad,
please read these instructions carefully and save this
manual for future reference.

Congratulations

The GE Choice Alert™ Wireless Alarm System is one of
the most affordable and expandable wireless alarm
systems available. You’ll discover that the system offers
many features typically found in custom installed
Alarm systems. The Choice Alert system is reliable and
easy-to-use. With Choice Alert you can select from a
line of Sensors, Accessories and Remote Transmitters;
start small and expand as you need, or create a system
that meets all your needs.

The Choice Alert System is protected by Priority
Code Selection technology which provides increased
security and trouble-free wireless connections. It also
guarantees the Control Center will only respond to
signals from your Sensors in and around your
home, and prevents anyone from tampering with
your system.

This user manual explains in simple steps how to
install, use and care for your new Choice Alert Wireless
Keypad.

If you have any questions or would like additional
information please visit our web site
www.jascoproducts.com, or contact our Tech Support
at 1-800-654-8483.

3

5

Important safeguards

PreCautions

1.

Do not attempt to disassemble the Wireless Keypad,
unless described in the user’s manual. There are no
user serviceable parts.

2. Handle with Care – Avoid striking or shaking.
Improper use or storage could damage the Wireless
Keypad. Modifying or tampering the device or its
internal components can cause a malfunction
and void the Wireless Keypad’s warranty.

3. If you feel the Wireless Keypad or any part of the
Choice Alert system is not operating correctly or
as described, please contact Technical Support for
assistance (1-800-654-8483).

4

Introduction

The Wireless Keypad allows you to wirelessly control
your Choice Alert System. With this keypad, you will
be able to arm, disarm and immediately activate the

alarm with up to three personalized security codes.

Parts Check List

Identify all the parts before proceeding.

Wireless Keypad

2 - Screws

1 2

3 4

2 - Plastic anchors

2- double sided adhesive tape

5

7

Activating the Battery

The Wireless Keypad is packaged with the battery
installed, but not activated. To activate the battery,
remove the yellow battery isolation strip on the side
edge; pull to remove. Once the strip is removed, the
Wireless Keypad will be active.

Assigning a Wireless Keypad to a Device Location

The Control Center is designed to store up to four
remote transmitters, such as the Wireless Keypad. In
order to ensure that the Wireless Keypad will operate
only with your Control Center, it must be assigned to
one of the four device locations on the Control Center.

Step 1. Press and hold the Learn button on the Control
Center. You will hear a short beep, followed shortly by a
long continuous beep. Release the Learn button.

Step 1

Press and hold
the Learn button
for three seconds

InputDC12V

-

Mute

Learn

Alert

Chime

Off

Step 3

+

To activate the keypad
press the panic button
on the unit.

1 2 3 4

Zone

Step 2

Press and release the
Device number

1 2 3 4

Arm

Armed Power

Step 2.

On the Control Center, press and release one of
the device numbers (1,2,3 or 4) that you want to assign
the Wireless Keypad. The LED for that device number
will begin to flash.

6