GE 26930 User Manual

INTRODUCTION

Your Caller ID phone stores and displays specific
information, provided by your local telephone company, to
subscribers of Caller ID or similar caller identification
services. You must subscribe to one of these services in
order to use this unit.

Your Caller ID phone enables you to:

• Identify callers before you answer the phone.

• View the time and date of each incoming call.

• Record up to 40 Caller ID messages sequentially.

• Know who called while you were away.

To get the most from your new phone, we suggest that you
take a few minutes right now to read through this user's guide.

IMPORTANT: In order to use this unit, you must
subscribe to either the standard Name/Number Caller
ID Service or Caller ID with Call Waiting Service. To
know who is calling while you are on the phone, you
must subscribe to Caller ID with Call Waiting Service.

IMPORTANT: Because cordless phones operate on
electricity, you should have at least one phone in your
home that isn’t cordless, in case the power in your
home goes out.

BEFORE YOU BEGIN

PARTS CHECKLIST

Make sure your package includes the items shown here.

INSTALLATION

DESKTOP INSTALLATION

NOTE: For desktop charging only, the handset is able

to charge facing up or down.

1. Place the handset in the base.

2. Raise the base antenna.

3. Plug the power supply cord into an AC outlet. The
CHARGE/IN USE indicator comes on indicating that the
battery is charging.

Allow the phone to charge for 12 hours prior to
first use. If you don't properly charge the phone,
battery performance will be compromised.

4. After charging, plug the telephone line cord into the
modular jack.

5. Set the RINGER switch on the handset to ON.

NOTE : The phone automatically defaults to touch­tone dialing. To change to pulse (rotary) dialing, see
“Tone/Pulse Dialing.” If you don’t know which type of
service you have, check with the phone company.

WALL MOUNT INSTALLATION

Because it is necessary to charge the handset for 12 hours
prior to connecting the phone for use the first time, it is
better to leave the unit on a flat surface during initial
charge before attempting to hang it on the wall.

1. Remove the handset hook; turn it upside down, and put
it back in the slot. You need to do this so the handset
doesn't fall out of the base when it is on the wall.

2. Set the RINGER switch on the handset to ON.

3. Place the handset in the base.

4. Plug the power supply into an AC outlet.

The CHARGE/IN USE indicator comes on indicating that
the battery is charging.

Allow the phone to charge for 12 hours prior to first
use. If you don't properly charge the phone, battery
performance will be compromised.

5. After charging, plug the telephone line cord into the
modular jack. Then stuff the excess line cord into the
mounting bracket.

6. Attach the wall
mount bracket by
inserting the two
tabs at the top
and then
snapping the tab
at the bottom into
place.

7. Slip the mounting
holes over the
wall plate posts
and slide the unit
down firmly into
place. (Wall plate
not included.)

8. Raise the base antenna.

NOTE : The phone automatically defaults to touch­tone dialing. To change to pulse (rotary) dialing, see
“Tone/Pulse Dialing.” If you don’t know which type of
service you have, check with the phone company.

CORDLESS PHONE BASICS

RECEIVING A CALL

1. Check the display to see who is calling.

2. Press the TALK button.

MAKING A CALL

To make a call, press the TALK button before you dial and
press it again to hang up.

REDIAL

While the phone is on, press the REDIAL button to redial
the last number you dialed (up to 32 digits). If you get a
busy signal, and want to keep dialing the number, just
press REDIAL again (you don't have to turn the phone off
and back on).

FLASH

Use the FLASH button to activate custom calling services
such as call waiting or call transfer, which
are available through your local phone company.

TIP: Don’t use the TALK button to activate custom
calling services such as call waiting, or you’ll hang up
the phone.

CHANNEL BUTTON

While talking, you might need to manually change the
channel in order to get rid of static. Press and release the
CHANNEL button to advance to the next clear channel.

TEMPORARY TONE

This feature enables Pulse (rotary) service phone users to
access touch-tone services offered by banks, credit card
companies, etc., by pressing the TONE button to temporarily
make the phone touch-tone compatible. To get information
about your bank account, for example, you would:

1. Call the bank’s information line.

2. Press the TONE button (*) after your call is answered.

3. Follow the voice instructions to complete your transaction.

4. Hang up when finished. The phone returns to Pulse
(rotary) service.

FINDING THE HANDSET

This feature helps to locate a misplaced handset.
Press the PAGE button on the base. The handset beeps

continuously for about 2 minutes or until you press any button
on the handset. You can also press PAGE again to cancel.

NOTE: The ringer does not have to be on for this
feature to work.

RINGER SWITCH

The RINGER switch must be ON for the handset to ring
during incoming calls.

TONE/PULSE DIALING

This adjustment allows you to select tone (touch-tone) or
pulse (rotary) mode dialing. The phone is automatically set
for touch-tone use.

TONE

1. Make sure the phone is OFF.

2. Press and hold the CHANNEL button for 2 seconds until
the phone beeps.

3. Press TONE*.

PULSE

1. Make sure the phone is OFF.

2. Press and hold the CHANNEL button for 2 seconds until
the phone beeps.

3. Press #.

VOLUME

The VOLUME button controls the volume of the
handset's earpiece.

VOICE MESSAGING

Provided your phone company
offers voice messaging service
and you subscribe to it, the
CHARGE/IN USE indicator on
the base flashes when the
phone is not in use to indicate
there is a message waiting. It
stops flashing after the
message has been reviewed.

CALLER ID FEATURES

This unit receives and displays information transmitted by
your local phone company. This information can include
the phone number, date, and time; or the name, phone
number, date, and time. The unit can store up to 40 calls
for later review.

CALLER ID WITH CALL WAITING

Provided you subscribe to Caller ID with Call Waiting
service from your phone company, you are able to see who
is calling when you hear the call waiting beep. The caller
identification information appears in the display after you
hear the tone.

• Press the FLASH button to put the current person on
hold so that you can answer the incoming call.

IMPORTANT: In order to use this unit, you must
subscribe to either the standard Name/Number Caller
ID Service or Caller ID with Call Waiting Service. To
know who is calling while you are on the phone, you
must subscribe to Caller ID with Call Waiting Service.

RECEIVING AND STORING CALLS

When you receive a call, the information is transmitted by
the phone company to your Caller ID telephone between
the first and second ring.

When the memory is full, a new call automatically replaces
the oldest call in memory.

NEW

appears in the display for

calls received that have not been reviewed.

NOTE: Check with your local phone company
regarding name service availability.

REVIEWING RECORDS

As calls are received and stored, the display is updated to
let you know how many calls have been received.

• Press the arrow down button to scroll through the call
records from the most recent to the oldest.

• Press the arrow up button to scroll through the call
records from the oldest to the newest.

• To display the last Caller ID record reviewed, make sure
the phone is OFF. Then press REDIAL. To dial the number,
press REDIAL again. The number dials automatically.

DELETING RECORDS

Use the DELETE button to erase the record currently shown
in the display or all records.

DELETING THE CURRENT RECORD

1. Make sure the phone is OFF.

2. Use the arrow buttons to display the desired Caller ID record.

3. Press DELETE. The display shows

ERASE CALL ID?

4. Press DELETE again to erase the record.

DELETING ALL RECORDS

1. Make sure the phone is OFF.

2. Use the arrow buttons to display the desired Caller ID record.

3. Press and hold DELETE. The display shows

ERASE ALL?

4. Press DELETE again to erase all records.

DIALING A CALLER ID NUMBER

1. Make sure the phone is OFF.

2. Use the arrow buttons to display the desired Caller ID record.

3. Press CALL BACK. The number dials automatically.

SETTING YOUR LOCAL AREA CODE

1. Press and hold the CHANNEL button until “AREA
CODE=000” shows in the display.

2. Use the handset numberpad to enter your 3-digit area code.

NOTE: To clear your local area code, press and hold
the CHANNEL button until your area code appears in
the display, then press 000.

CHANGING THE NUMBER FORMAT

The FORMAT button lets you change the format of the
displayed number. The available formats are as follows.

7-digit 7-digit telephone number.

10-digit 3-digit area code + 7-digit telephone

number.

11-digit long distance code “1” + 3-digit area code +

7-digit telephone number.

1. Use the arrow buttons to scroll to the number you want
to call back.

2. If the number will not dial as shown, press the FORMAT
button. Repeat if necessary, until the correct number of
digits are shown.

3. Press CALL BACK. The number dials automatically.

MEMORY

Store up to ten 24-digit numbers in memory for quick
dialing. This memory feature is in addition to the 40 Caller
ID records that can be stored in the Caller ID memory log.

STORING A NUMBER IN MEMORY

1. Make sure the phone is OFF.

2. Press the MEMORY button.

3. Press the memory location number (0-9).

4. Press MEMORY again. The display shows

ENTER NAME.

NOTE: If you don't want to enter the name, skip step 5.

5. Use the keypad to store a name (up to 15 characters).
More than one letter or character is stored in each of the
number keys. For example, to enter Joe Smith, press 5
for J; press 6 three times for O; press 3 two times for E;
press 1 to enter a space before you start entering the
last name; press 7 four times for S; press 6 for M; press
4 three times for I; press 8 for T; and 4 two times for H.

If you're using two letters consecutively that are stored
in the same number key, you must press FORMAT
between the letters. For example, if you enter Barb,
press 2 two times for B; press FORMAT; press 2 for A; 7
three times for R; and 2 two times for B. You need to
press FORMAT between the B and the A since they are
stored within the same number key.

6. Press MEMORY. The display shows

ENTER TEL NUMBR

.

7. Use the keypad to enter the number you want to store
(up to 24 digits). To add a pause, See “Inserting a Pause
in the Dialing Sequence”.

8. Press MEMORY again to store the number.

26930

40-Channel 900Mhz Caller ID with
Call Waiting Cordless Telephone
User's Guide

We bring good things to life.

FCC REGISTRATION INFORMATION

Your telephone equipment is registered with the Federal
Communications Commission and is in compliance with parts 15 and
68, FCC Rules and Regulations.
1 Notification to the Local Telephone Company

On the bottom of this equipment is a label indicating, among other
information, the FCC Registration number and Ringer Equivalence
Number (REN) for the equipment. You must, upon request, provide
this information to your telephone company.
The REN is useful in determining the number of devices you may
connect to your telephone line and still have all of these devices
ring when your telephone number is called. In most (but not all)
areas, the sum of the RENs of all devices connected to one line
should not exceed 5. To be certain of the number of devices you may
connect to your line as determined by the REN, you should contact
your local telephone company.

Notes

• This equipment may not be used on coin service provided by the
telephone company.

• Party lines are subject to state tariffs, and therefore, you may not
be able to use your own telephone equipment if you are on a
party line. Check with your local telephone company.

• Notice must be given to the telephone company upon
permanent disconnection of your telephone from your line.

2 Rights of the Telephone Company

Should your equipment cause trouble on your line which may
harm the telephone network, the telephone company shall, where
practicable, notify you that temporary discontinuance of service
may be required. Where prior notice is not practicable and the
circumstances warrant such action, the telephone company may
temporarily discontinue service immediately. In case of such
temporary discontinuance, the telephone company must: (1)
promptly notify you of such temporary discontinuance; (2) afford
you the opportunity to correct the situation; and (3) inform you of
your right to bring a complaint to the Commission pursuant to
procedures set forth in Subpart E of Part 68, FCC Rules and
Regulations.
The telephone company may make changes in its communications
facilities, equipment, operations or procedures where such action
is required in the operation of its business and not inconsistent
with FCC Rules and Regulations. If these changes are expected to
affect the use or performance of your telephone equipment, the
telephone company must give you adequate notice, in writing, to
allow you to maintain uninterrupted service.

ATLINKS USA, Inc.

10330 North Meridian Street

Indianapolis, IN 46290
© 2001 ATLINKS USA, Inc.
Trademark(s) ® Registered

Marca(s) ® Registrada(s)

Model 26930C/D
15574080 (Rev. 3 DOM E)
01-18
Printed in China

Base

Handset

Mounting bracket

CHARGE/ IN USE

PAGE

10:2810/20 03

3175551234

FRED PAGE

PM REPT

CALL

#

VOLUME

CID REVIEW

CALL BACK

DELETE

RINGER

OFF ON

FLASH

FORMAT

CHANNEL

REDIAL MEMORY

TALK

WXYZ9TUV8PQRS

7

MNO6JKL5GHI

4

DEF3ABC

21

#

OPER0TONE

*

10:28 10/20 03

3175551234

FRED PAGE

PM REPT

CALL

#

VOLUME

CID REVIEW

CALL BACK

DELETE

RINGER

OFF ON

FLASH

FORMAT

CHANNEL

REDIAL MEMORY

TALK

WXYZ9TUV8PQRS

7

MNO6JKL5GHI

4

DEF3ABC

21

#

OPER0TONE

*

CHANNEL
button

DELETE/
FLASH
button

TALK
button

CALL BACK/
REDIAL button

TONE
button

RINGER
switch

VOLUME
button

FORMAT
button

MEMORY
button

CHARGE/ IN USE

PAGE

CHARGE/IN USE indicator

Caller ID name

10:28 10/20 03

3175551234

FRED PAGE

PM REPT

CALL

#

Time

Date

Number of calls

Caller ID phone number

MODULAR JACK REQUIREMENTS

You need an RJ11 type modular phone jack,
which is the most common type of phone jack
and might look like the one pictured here. If you
don’t have a modular jack, call your local phone
company to find out how to get one installed.

INSTALLATION NOTE: Some cordless
telephones operate at frequencies that may cause
interference to nearby TVs, microwave ovens, and
VCRs. To minimize or prevent such interference, the
base of the cordless telephone should not be placed
near or on top of a TV, microwave oven, or VCR. If
such interference continues, move the cordless
telephone farther away from these appliances.

DIGITAL SECURITY SYSTEM

Your cordless phone uses a digital security system to
provide protection against false ringing, unauthorized
access, and charges to your phone line.

When you place the handset in the base, the unit verifies
its security code. After a power outage or battery replace­ment, you should place the handset in the base for about
20 seconds to reset the code.

Belt clip

4

1

2

3

5

3

2

4

1

5

7

6

8

SEE MARKING ON BOTTOM / BACK OF PRODUCT

RISK OF ELECTRIC SHOCK
DO NOT OPEN

WARNING: TO PREVENT FIRE OR
ELECTRICAL SHOCK HAZARD, DO
NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.

THE LIGHTNING FLASH
AND ARROW HEAD
WITHIN THE TRIANGLE
IS A WARNING SIGN
ALERTING YOU OF
“DANGEROUS
VOLTAGE” INSIDE THE
PRODUCT.

CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE
PERSONNEL.

THE EXCLAMATION
POINT WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
IMPORTANT
INSTRUCTIONS
ACCOMPANYING THE
PRODUCT.

CAUTION:

CHANGING A STORED NUMBER

Use the same procedure to change a stored number as you
do to store a number—you’re just replacing the phone
number with a different one.

DIALING A STORED NUMBER

1. Make sure the phone is ON by pressing the TALK button.

2. Press MEMORY.

3. Press the number (0-9) for the desired memory location.
The number dials automatically.

- OR -

1. Make sure the phone is OFF.

2. Press MEMORY.

3. Use the arrow buttons to scroll through the numbers
stored in memory until the desired number is shown.

4. Press CALL BACK. The numbers dials automatically.

IMPORTANT: If you make test calls to emergency
numbers stored in memory, remain on the line and
briefly explain the reason for the call to the dispatcher.
Also, it’s a good idea to make these calls in off-peak
hours, such as early morning or late evening.

INSERTING A PAUSE IN THE DIALING
SEQUENCE

Press the REDIAL button to insert a delay in the dialing
sequence of a stored telephone number when a pause is
needed to wait for a dial tone (for example after you dial 9
for an outside line, or to wait for a computer access tone).
Each pause counts as 1 digit in the dialing sequence.

REVIEWING AND DELETING STORED
NUMBERS

1. Press MEMORY, then use the arrow keys to view the entry.

2. While the entry is displayed, press DELETE to delete the
entry. The display shows

ERASE MEMO?

3. Press DELETE a second time to delete the entry.

CHAIN DIALING FROM MEMORY

Use this feature to make calls which require a sequence of
numbers such as using a calling card for a frequently
called long distance number. Basically, you dial each part
of the sequence from memory. The following example
shows how you can use chain dialing to make a call
through a long distance service:

The Number For Memory Location
Long distance access number 7

Authorization code 8
Frequently called long distance number 9

1. Make sure the phone is ON.

2. Press MEMORY and then press 7.

3. When you hear the access tone, press MEMORY and
then press 8.

4. At the next access tone, press MEMORY and then 9.

TIP: Wait for the access tones before pressing the next
memory button, or your call might not go through.

HEADSET AND BELT CLIP
OPERATION

CONNECTING A HEADSET TO THE

HANDSET

For hands free
conversation, connect the
headset (optional) to the
HEADSET jack as shown.
The handset receiver and
microphone are disabled
when the headset is
connected.

Adjust the headset to rest
comfortably on top of your
head and over your ear.
Move the microphone to
approximately 2 to 3 inches
from your mouth.

• Press the TALK button to
answer or place a call
before using the headset.

CONNECTING THE BELT CLIP

There are two slots, one on
each side of the handset.

• Attach the belt clip by
inserting the sides of the
belt clip into the slots.
Snap the ends of the belt
clip into place.

CHANGING THE BATTERY

Make sure the telephone is OFF before you replace
battery.

1. Remove the battery compartment door.

2. Disconnect the cord attached to
the battery pack and remove the
battery pack from the handset.

3. Insert the new battery pack and
connect the cord into the jack
inside the handset.

4. Put the battery compartment door
back on.

5. Place handset in the base to
charge. If you don’t charge the

handset battery properly (for 12 hours)
when you first set up the phone and/or
when you install a new battery pack,
the battery’s long-term performance
will be compromised.

BATTERY SAFETY PRECAUTIONS

• Do not burn, disassemble, mutilate, or puncture. Like
other batteries of this type, toxic materials could be
released which can cause injury.

• To reduce the risk of fire or personal injury, use only the
battery listed in the User’s Guide.

• Keep batteries out of the reach of children.

• Remove batteries if storing over 30 days.

Ni-Cd

RBRC

RBRC

GENERAL PRODUCT CARE

To keep your telephone working and looking good, follow
these guidelines:

• Avoid putting the phone near heating appliances and
devices that generate electrical noise (for example,
motors or fluorescent lamps).

• DO NOT expose to direct sunlight or moisture.

• Avoid dropping the handset, as well as other rough
treatment to the phone.

• Clean the phone with a soft cloth.

• Never use a strong cleaning agent or abrasive powder
because this will damage the finish.

• Retain the original packaging in case you need to ship
the phone at a later date.

• Periodically clean the charge contacts on the handset
and base with a clean pencil eraser.

CAUSES OF POOR RECEPTION

• Aluminum siding

• Foil backing on insulation

• Heating ducts and other metal construction can shield
radio signals

• You’re too close to appliances such as microwaves,
stoves, computers, etc.

• Atmospheric conditions, such as strong storms

• Base is installed in the basement or lower floor of the house

• Base is plugged into an AC outlet with other electronic devices

• Baby monitor is using the same frequency

• Handset battery is low.

• You’re out of range of the base.

MESSAGE INDICATORS

The following indicators show the status of a
message or of the unit.

ERROR Caller information has been interrupted

during transmission or the phone is
excessively noisy.

ENTER NAME Prompt telling you to enter a name for

one of the 10 memory locations.

ERASE ALL? Prompt asking if you want to erase all

Caller ID records.

ERASE CALL ID? Prompt asking if you want to erase the

current Caller ID record that is shown
on the display.

ERASE MEMO? Prompt asking if you want to erase one

of the 10 numbers stored in the
phone's outgoing memory.

END OF LIST Indicates there is no additional

information in the Caller ID memory log.

NEW Indicates call or calls have not been

reviewed.

UNKNOWN The incoming call is from an area not

serviced by Caller ID or the information
was not sent.

PAGING YOU Someone has pressed the PAGE button

on the base.

BLOCKED The person is calling from a number that

has been blocked from transmission.

REPT Repeat call message. Indicates that a

new call from the same number was
received more than once.

NO DATA No Caller ID information was received.

H

ANDSET SOUND SIGNALS

Signal Meaning
A long warbling tone Signals an incoming call

(with ringer on)
One short beep, one Page signal

long beep (several times)
Three short beeps Out of range
Four short beeps Low battery warning

TROUBLESHOOTING TIPS

CALLER ID

Problem Solution

No Display • Is battery fully charged? Try

replacing the battery.

• If you are using AC power,
make sure that the unit is
connected to a non-switched
electrical outlet. Disconnect
the unit from the plug and
plug it in again.

• Did you order Caller ID
service from your local
telephone company?

Caller ID Error Message • The unit displays this

message if it detects
anything other than valid
Caller ID information during
the silent period after the
first ring. This message
indicates the presence of
noise on the line.

TELEPHONE

Problem Solution
No dial tone • Check installation:

— Is the base power cord

connected to a working outlet?

— Is the telephone line cord

connected to the base unit
and the wall jack?

• Disconnect the base from
the wall jack and connect
another phone to the same
jack. If there is no dial tone
in the second phone, the
problem might be your
wiring or local service.

• Is the handset out of range
of the base?

• Make sure the battery is
properly charged (12 hours).

• Is the battery pack
installed correctly?

• Did the handset beep
when you pressed the
TALK button? Did the
CHARGE/ IN USE indicator
come on? The battery may
need to be charged.

TELEPHONE

Problem Solution

Dial tone is OK, but • Make sure the tone/
can't dial out pulse setting is programmed

correctly.

Handset does not ring • Make sure the RINGER

switch on the handset is
turned to ON.

• You may have too many
extension phones on your line.
Try unplugging some phones.

• See solutions for “No dial tone.”

You experience static, • Change channels
noise, or fading in • Is handset out of range?
and out Move closer to the base.

• Does the base need to be
relocated?

• Charge battery.

• Make sure base is not
plugged into an outlet with
another household
appliance.

Unit beeps • Place handset in base for

20 seconds to reset the
security code. If that
doesn’t work, charge
battery for 12 hours.

• Clean charging contacts on
handset and base with a
soft cloth, or an eraser.

• See solutions for “No dial tone.”

• Replace battery.

Memory Dialing • Did you program the memory

location keys correctly?

• Did you follow proper
dialing sequence?

• Make sure the tone/pulse
setting is programmed correctly.

• Did you reprogram
numbers into memory
after power outage or
battery replacement?

S

ERVICE

The FCC requires this product to be serviced only by the
manufacturer or its authorized service agents. In
accordance with FCC requirements, changes or
modifications not expressly approved by ATLINKS USA,
Inc. could void the user’s authority to operate this product.
For instructions on how to obtain service, refer to the
warranty included in this user's guide or contact Consumer
Information at 1-800-448-0329.

Or refer inquiries to:
ATLINKS USA, Inc.
Manager, Consumer Relations
P O Box 1976
Indianapolis, IN 46206

Attach your sales receipt to the booklet for future reference
or jot down the date this product was purchased or
received as a gift. This information will be valuable if
service should be required during the warranty period.

Purchase date__________ Name of store__________________

NOTE: The RBRC seal on the battery
used in your ATLINKS USA, Inc.
product indicates that we are
participating in a program to collect
and recycle Nickel Cadmium batteries
throughout the United States. Please
call 1-800-8-BATTERY for information
or contact your local recycling center.

INTERFERENCE INFORMATION

This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference; and (2) This device must accept any
interference received, including interference that may cause
undesired operation.

This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation.

If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

• Reorient or relocate the receiving antenna (that is, the antenna
for radio or television that is “receiving” the interference).

• Reorient or relocate and increase the separation between the
telecommunications equipment and receiving antenna.

• Connect the telecommunications equipment into an outlet on a circuit
different from that to which the receiving antenna is connected.

• Consult the dealer or an experienced radio/TV technician for help.

If these measures do not eliminate the interference, please consult
your dealer or an experienced radio/television technician for
additional suggestions. Also, the Federal Communications
Commission has prepared a helpful booklet, “How To Identify and
Resolve Radio/TV Interference Problems.” This booklet is available
from the U.S. Government Printing Office, Washington, D.C. 20402.
Please specify stock number 004-000-00345-4 when ordering copies.

LIMITED WARRANTY

What your warranty covers:

• Defects in materials or workmanship.

For how long after your purchase:

• One year, from date of purchase.
(The warranty period for rental units begins with the first rental or 45 days from
date of shipment to the rental firm, whichever comes first.)

What we will do:

• Provide you with a new or, at our option, a refurbished unit.

• The exchange unit is under warranty for the remainder of the original
product’s warranty period.

How to make a warranty claim:

• Properly pack your unit. Include any cables, etc., which were originally
provided with the product. We recommend using the original carton and
packing materials.

• ”Proof of purchase in the form of a bill of sale or receipted invoice which is
evidence that the product is within the warranty period, must be presented to
obtain warranty service.” Also print your name and address and a description
of the defect. Send via standard UPS or its equivalent to:

ATLINKS USA, Inc. c/o Thomson multimedia Inc.
11721 B Alameda Ave.
Socorro, Texas 79927

• Pay any charges billed to you by the Exchange Center for service not
covered by the warranty.

• Insure your shipment for loss or damage. Thomson multimedia Inc.
accepts no liability in case of damage or loss en route to Thomson
multimedia Inc..

• A new or refurbished unit will be shipped to you freight prepaid.

What your warranty

does not

cover:

• Customer instruction. (Your Owner’s Manual provides information regarding
operating instructions and user controls. Any additional information, should
be obtained from your dealer.)

• Installation and setup service adjustments.

• Batteries.

• Damage from misuse or neglect.

• Products which have been modified or incorporated into other products.

• Products purchased or serviced outside the USA.

• Acts of nature, such as but not limited to lightning damage.

Product Registration:

• Please complete and mail the Product Registration Card packed with your
unit. It will make it easier to contact, you should it ever be necessary. The
return of the card is not required for warranty coverage.

Limitation of Warranty:

• THE WARRANTY STATED ABOVE IS THE ONLY WARRANTY APPLICABLE TO
THIS PRODUCT. ALL OTHER WARRANTIES, EXPRESS OR IMPLIED
(INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE) ARE HEREBY DISCLAIMED. NO VERBAL OR
WRITTEN INFORMATION GIVEN BY ATLINKS USA, INC., IT’S AGENTS, OR
EMPLOYEES SHALL CREATE A GUARANTY OR IN ANY WAY INCREASE THE
SCOPE OF THIS WARRANTY.

• REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE
EXCLUSIVE REMEDY OF THE CONSUMER. ATLINKS USA, INC. SHALL NOT
BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING
FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF
ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. THIS
DISCLAIMER OF WARRANTIES AND LIMITED WARRANTY ARE GOVERNED
BY THE LAWS OF THE STATE OF INDIANA. EXCEPT TO THE EXTENT
PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS
PRODUCT IS LIMITED TO THE APPLICABLE WARRANTY PERIOD SET
FORTH ABOVE.

How state law relates to this warranty:

• Some states do not allow the exclusion no limitation of incidental or
consequential damage, or limitation on how long an implied warranty
lasts so the above limitations or exclusions may not apply to you.

• This warranty gives you specific legal rights, and you may have other
rights which vary from state to state.

If you purchased your product outside the USA:

• This warranty does not apply. Contact your dealer for warranty
information.

ACCESSORY ORDER FORM

(OR CALL 1-800-338-0376 FOR ACCESSORIES ONLY)

CUSTOMER: CUT ALONG DOTTED LINE.

✂

*Prices are subject to change without notice.

Total Merchandise.........................................$_______________

Sales Tax........................................................$_______________

We are required by law to collect the appropriate sales tax for each individual state,
county, and locality to which the merchandise is being sent. Duties will apply for
shipments to Canada.

Use VISA or Master Card or Discover preferably. Money order or check must be in U.S.
currency only. No COD or Cash. All accessories are subject to availability. Where
applicable, we will ship a superseding model.

Shipping/Handling....................................... $_______________

Total Amount Enclosed.................................$_______________

Mail order form and money order or check (in U.S. currency)
made payable to Thomson multimedia Inc. to:

Thomson multimedia Inc.
Mail Order Department
P.O. Box 8419
Ronks, PA 17573-8419

Name_______________________________________________________
Address_____________________________________ Apt.____________
City ________________________State________ ZIP_________________
Daytime Phone Number ( )_______________________________

Please make sure that this form has been filled out completely.

____________________________________________________________________

Authorized Signature

My card expires:

Copy the number above your
name on the Master Card

For credit card purchases

Your complete charge card number, its expiration date and your
signature are necessary to process all charge card orders.

Copy your complete account number from your VISA card.

My card expires:

Copy your complete account number from your

Master Card or Discover.

$5.00

DESCRIPTION

CATALOG NO.

TOTAL

QTY.

PRICE*

Belt clip

5-2462

$4.95

Headset

5-2425

$36.35

5-2461

$14.95

Replacement battery

5-2463

5-2444

(white)

(black)

HEADSET

Headset
jack

Headset
plug

Slot for
belt clip

Slot for
belt clip