GE 2600 Series Owner’s Manual
Zoneline Heat/Cool Models
2600 Series
Zoneline
Owner’s Manual
®
Important Safety Information
Operating Instructions
The Controls on Your Zoneline
Care of Product
Installation Instructions
Important Electrical Safety
Adjustments and Auxiliary Controls
Helpful Information
Things That Are Normal
3
4
10
18
If Something Goes Wrong
Before You Call For Service
GE Service Numbers
Warranty
GE Answer Center
®
800.626.2000
GE Appliances
19
Welcome
Welcome to the GE family. We’re
proud of our quality products and
we believe in dependable service.
You’ll see it in this easy-to-use
manual and you’ll hear it in the
friendly voices of our customer
service department.
Best of all, you’ll experience
these values each time you enjoy
the comfort of your Zoneline.
That’s important, because your
new Zoneline will be part of your
family for a long time.
Start Here!
Before using
your
Zoneline
Staple your receipt to the inside back
cover of this manual. You will need it
to obtain service under warranty.
Write down the model and serial
numbers here.
behind the room cabinet.
Model number
Serial number
Date of purchase
They are on a label
Need Help?
Help us
help you
800.626.2000
2
Before you call for service,
there are a few things you can
do to help us serve you better.
Read this manual.
instructions to help you use and
maintain your Zoneline properly.
Save time and money.
section titled “If Something Goes
Wrong” before calling. This section was designed to solve common
problems that might occur.
It contains
Check the
If you do need service, you can
relax knowing help is only a phone
call away. Toll-free customer service
numbers are included in the back
of this manual. Or call the
Answer Center
24 hours a day, 7 days a week.
®
at 800.626.2000,
GE
Important Safety Information
Read all safety information before using
• This Zoneline must be properly
installed in accordance with the
Installation Instructions before it
is used.
• Repair or replace immediately
all electric service cords that have
become frayed or otherwise
damaged.
SAVE THESE INSTRUCTIONS
• Unplug or disconnect the
Zoneline at the fuse box or
circuit breaker before making
any repairs.
NOTE:
that any servicing be performed
by a qualified individual.
We strongly recommend
3
The
Operating Instructions
controls
MODE
COOL FAN HEAT
on your
Zoneline
FAN
1
Mode Control Temp Control
COOL—
HEAT—
FAN—
The fan controls cooling or heating with
LOW
automatically switches between low and high to
adjust for room temperature changes.
For cooling
For heating
For fan-only operation
fan speed operation. When set at
HIGH LOW AUTO
1
HIGH
AUTO
, it
or
COOLER WARMER
CALL
SVC
STOP/ON
TEMP
2
2
The temp control is used to maintain the
room temperature. The compressor will cycle
on and off to keep the room at the same level
of comfort.
COOLER—
WARMER—
STOP/ON
tion. Power remains connected to the Zoneline
and the Freeze Sentinel still functions.
For cooler temperatures
For warmer temperatures
—Stops heating, cooling and fan opera-
The
CALL SVC
if the compressor fails to start. If the control is
set at
COOL
operates alone. If set at
HEAT
4
setting. Call for service as soon as possible.
(call service) indicator will light
, the compressor stops and the fan
HEAT
, it continues in the
Energy Tips
Keep the vent control at
The air will be filtered and
circulated.
OPEN
Vent
control
CLOSE
CLOSE
3 4
.
Setthe
between low and high to adjust
for room temperature changes.
FAN
at
AUTO
. It switches
Adjust the air louvers straight out
to get the most hot or cool air into
the room.
Air louvers
Ventilation Control Air Direction
The ventilation control lever is located at the
lower left side of the Zoneline unit, behind the
room cabinet.
When set at
is circulated and filtered.
When set at
drawn into the room. This will reduce the
heating or cooling effect.
CLOSE
OPEN
, only the air inside the room
, some outdoor air will be
43
Adjust the air louvers by moving them with
your fingers. To get the most hot or cool air
into the room, set the louvers straight out.
5
Operating Instructions
Other Zoneline features
To Remove the
Room Cabinet
Fan Switch
Fan switch
9
ON
OFF
Auxiliary Controls
Down—Continuous Fan
Up—Cycle Fan
OFF
ON
Additional controls are located
behind the room cabinet.
To remove:
Pull out to release it
from the tabs. Then lift up.
2
1
The fan switch 9 is located behind
the room cabinet.
This switch is set at continuous fan
(down) at the factory to provide
continuous fan operation in cool
or heat modes. Leaving the switch
in the continuous fan setting allows
continuous circulation of room air
and will result in a more balanced
temperature throughout the room.
To replace:
Place the tabs over
the top rail. Push inward until
it snaps into place.
1
2
If you want the fan to cycle on
and off with the compressor or
with the heater, move the switch
to cycle fan (up).
6
Freeze Sentinel
The Freeze Sentinel feature
automatically turns on the
resistance heater and fan if the
room temperature (sensed at
the unit) drops to approximately
45°F. It will turn the heater off
when the temperature reaches
about 50°F.
The Freeze Sentinel helps prevent
plumbing damage in the room due
to sub-freezing temperatures.
The Freeze Sentinel is active as long
as power to the unit has not been
interrupted.
7
Operating Instructions
Care & Cleaning
Room Cabinet
and Case
Outdoor Coils
Base Pan
Turn the Zoneline off and remove
the plug from the wall outlet
before cleaning.
The coils on the outdoor side of
the Zoneline should be checked
regularly. If they are clogged with
dirt or soot they may be professionally steam cleaned, a service available through your GE service
outlet.
In some installations, dirt or other
debris may be blown into the unit
from the outside and settle in the
base pan (the bottom of the unit).
To clean, use water and a mild
detergent. Do not use bleach or
abrasives.
Check it periodically and clean it
out, if necessary.
8
Loading...