GE 200D2600P043 User Manual

www.GEAppliances.com

Refrigerators

Profile Side by Side

200D2600P043 49-60352-2 12-04 JR

La section française commence à la page 44

La sección en español empieza en la página 82

Safety Instructions . . . . . . . . . . .2–4

Operating Instructions

Automatic Icemaker . . . . . . . . . . .12

Care and Cleaning . . . . . . . . . .14, 15

Crispers and Pans . . . . . . . . . . . . .11

Ice and Water Dispenser . . . . . . . .13

Refrigerator Doors . . . . . . . . . . . .10

Replacing the Light Bulbs . . . . . . .16

Shelves, Bins and Racks . . . . . . . .8, 9

Temperature Controls . . . . . . . . . . .5

TurboCool

™

. . . . . . . . . . . . . . . . . . .6

Water Filter . . . . . . . . . . . . . . . . . . .7

Installation Instructions

Installing the Refrigerator . . . .26–29

Moving the Refrigerator . . . . .22–25

Preparing to Install

the Refrigerator . . . . . . . . . . . . . . .21

Trim Kits and Panels . . . . . . . .17–20

Water Line Installation . . . . . .30–32

Troubleshooting Tips . . . . . . .33–36

Normal Operating Sounds . . . . . .33

Consumer Support

Consumer Support . . . . .Back Cover

Performance Data Sheet . . . . . . . .40

Product Registration . . . . . . . .37, 38

State of California Water

Treatment Device Certificate . . . . .41

Warranty (Canadian) . . . . . . . . . . .42

Warranty (U.S.) . . . . . . . . . . . . . . .43

Réfrigérateurs

Profile Côte à Côte

Refrigeradores

Profile Lado a Lado

Models 23, 25, 26, 27 and 29

Write the model and serial
numbers here:

Model # ______________________

Serial # ______________________

Find these numbers on a label inside
the refrigerator compartment at the
top on the right side.

Owner’s Manual

and Installation

Manuel d’utilisation

et d’installation

Manual del propietario

e instalación

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

2

IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

Use this appliance only for its intended purpose as described in this Owner’s Manual.

SAFETY PRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:

■

■ This refrigerator must be properly installed

and located in accordance with the Installation
Instructions before it is used.

■

■ Do not allow children to climb, stand or hang

on the shelves in the refrigerator. They could
damage the refrigerator and seriously injure
themselves.

■

■ Do not touch the cold surfaces in the freezer

compartment when hands are damp or wet.
Skin may stick to these extremely cold surfaces.

■

■ Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any
other appliance.

■

■ In refrigerators with automatic icemakers,

avoid contact with the moving parts of the
ejector mechanism, or with the heating
element located on the bottom of the icemaker.
Do not place fingers or hands on the automatic
icemaking mechanism while the refrigerator
is plugged in.

■

■ Keep fingers out of the “pinch point” areas;

clearances between the doors and between
the doors and cabinet are necessarily small.
Be careful closing doors when children are
in the area.

■

■ Unplug the refrigerator before cleaning and

making repairs.

NOTE: We strongly recommend that any servicing be
performed by a qualified individual.

■

■ Setting either or both controls to 0 (off) does not

remove power to the light circuit.

■

■ Do not refreeze frozen foods which have

thawed completely.

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

www.GEAppliances.com

PROPER DISPOSAL OF THE REFRIGERATOR

Child entrapment and suffocation are not problems
of the past. Junked or abandoned refrigerators are
still dangerous…even if they will sit for “just a few
days.” If you are getting rid of your old refrigerator,
please follow the instructions below to help prevent
accidents.

Before You Throw Away Your Old Refrigerator
or Freezer:

■ Take off the doors.

■ Leave the shelves in place so that children may

not easily climb inside.

Refrigerants

All refrigeration products contain refrigerants,
which under federal law must be removed prior
to product disposal. If you are getting rid of an
old refrigeration product, check with the
company handling the disposal about what
to do.

USE OF EXTENSION CORDS

Because of potential safety hazards under certain conditions, we strongly recommend against the use
of an extension cord.

However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed (in the United
States) or a CSA-listed (in Canada), 3-wire grounding type appliance extension cord having a grounding
type plug and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 120 volts.

DANGER! RISK OF CHILD ENTRAPMENT

3

4

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

HOW TO CONNECT ELECTRICITY

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.
For personal safety, this appliance must be properly grounded.

The power cord of this appliance is equipped with
a 3-prong (grounding) plug which mates with
a standard 3-prong (grounding) wall outlet to
minimize the possibility of electric shock hazard
from this appliance.

Have the wall outlet and circuit checked by
a qualified electrician to make sure the outlet
is properly grounded.

If the outlet is a standard 2-prong outlet, it is
your personal responsibility and obligation to
have it replaced with a properly grounded
3-prong wall outlet.

The refrigerator should always be plugged into
its own individual electrical outlet which has
a voltage rating that matches the rating plate.

This provides the best performance and also
prevents overloading house wiring circuits which
could cause a fire hazard from overheated wires.

Never unplug your refrigerator by pulling on
the power cord. Always grip plug firmly and pull
straight out from the outlet.

Repair or replace immediately all power cords that
have become frayed or otherwise damaged. Do not
use a cord that shows cracks or abrasion damage
along its length or at either end.

When moving the refrigerator away from the
wall, be careful not to roll over or damage the
power cord.

USE OF ADAPTER PLUGS (Adapter plugs not permitted in Canada)

Because of potential safety hazards under certain conditions, we strongly recommend against
the use of an adapter plug.

However, if you must use an adapter, where local
codes permit, a temporary connection may be made
to a properly grounded 2-prong wall outlet by use
of a UL-listed adapter available at most local
hardware stores.

The larger slot in the adapter must be aligned with
the larger slot in the wall outlet to provide proper
polarity in the connection of the power cord.

When disconnecting the power cord from the
adapter, always hold the adapter in place with one
hand while pulling the power cord plug with the
other hand. If this is not done, the adapter ground
terminal is very likely to break with repeated use.

If the adapter ground terminal breaks, DO NOT
USE the refrigerator until a proper ground has
been established.

Attaching the adapter ground terminal to a wall outlet
cover screw does not ground the appliance unless the
cover screw is metal, and not insulated, and the wall
outlet is grounded through the house wiring. You should
have the circuit checked by a qualified electrician to
make sure the outlet is properly grounded.

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

5

About the temperature controls. www.GEAppliances.com

The temperature controls are preset in the factory at 5 for both
the refrigerator and freezer compartments. Allow 24 hours for the
temperature to stabilize to the preset recommended settings.

Several adjustments may be required. Each time you adjust
controls, allow 24 hours for the refrigerator to reach the setting
you have selected.

Setting either or both controls to 0 stops cooling in both the freezer
and refrigerator compartments, but does not shut off electrical power
to the refrigerator.

Control settings will vary based on personal preferences, usage and
operating conditions and may require more than one adjustment.

NOTE: The refrigerator is shipped with protective film covering the

temperature controls. If this film was not removed during installation,
remove it now.

The Performance Air Flow System is designed to maximize temperature control in the refrigerator and
freezer compartments. This unique special feature consists of the Air Tower along the back wall of the
refrigerator and the Air Tunnel on the bottom portion of the freezer rear wall. Placing food in front of the
louvers on these components will not affect performance. Although the Air Tower and the Air Tunnel can
be removed, doing so will affect temperature performance. (For removal instructions, on-line, 24 hours a
day, contact us at GEAppliances.com or call 800.GE.CARES. In Canada, contact us at www.geappliances.ca
or call 1.800.361.3400.)

Performance Air Flow System

ADJUST FREEZER TEMP

WARMERCOLDER

9 IS COLDEST

ADJUST REFRIGERATOR TEMP

WARMERCOLDER

9 IS COLDEST

6

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

About TurboCool.

™

How it Works

TurboCool™rapidly cools the refrigerator

compartment in order to more quickly
cool foods. Use TurboCool when adding a
large amount of food to the refrigerator
compartment, putting away foods after they
have been sitting out at room temperature
or when putting away warm leftovers. It can
also be used if the refrigerator has been
without power for an extended period.

Once activated, the compressor will turn on
immediately and the fans will cycle on and
off at high speed as needed for eight hours.
The compressor will continue to run until
the refrigerator compartment cools to
approximately 34°F (1°C), then it will cycle
on and off to maintain this setting. After
8 hours, or if TurboCool is pressed again,
the refrigerator compartment will return
to the original setting.

How to Use

Press TurboCool. The refrigerator
temperature display will show TC.

After TurboCool is complete, the refrigerator
compartment will return to the original
setting.

NOTES:

The refrigerator temperature cannot be changed
during TurboCool.

The freezer temperature is not affected during
TurboCool.

When opening the refrigerator door during
TurboCool, the fans will continue to run if they
have cycled on.

About ClimateKeeper2.

™

How it Works

The new ClimateKeeper2™is the industry’s
most advanced refrigeration system,
delivering optimum temperature and
humidity performance to keep food fresh
longer and reduce freezer burn, while
maintaining E star-level efficiency.

The new ClimateKeeper2 system features
two evaporators—one for the refrigerator
and one for the freezer.

This provides two separate cooling systems
for the entire unit, and separates the
airflow between the fresh food and freezer
sections during normal cooling operations.*

This ensures that the humidity levels in the
fresh food section are significantly higher
than in a conventional system,** allowing
fresh produce and other unsealed foods to
retain their moisture content and freshness
longer. Moisture sensitive foods such as
fresh fruit, salads, rice, etc., can now be
stored on open shelves without excessive
moisture loss.

The separate airflow system minimizes
the mixing of air between the two
compartments, which reduces odor
transfer, resulting in improved taste of ice.

The ClimateKeeper2 system also reduces
the number of defrosting cycles in the
freezer evaporator, thereby improving the
temperature maintained in the freezer and
reducing freezer burn.

*Freezer air is used in the CustomCool feature.

**Testing shows a higher level of humidity in

the Fresh Food section in ClimateKeeper2
refrigerators versus conventional units.

7

About the water filter. (on some models) www.GEAppliances.com

On some models

Water Filter Cartridge

The water filter cartridge is located in the
back upper right corner of the refrigerator
compartment.

When to Replace the Filter

There is a replacement indicator light for
the water filter cartridge on the dispenser.
This light will turn orange to tell you that
you need to replace the filter soon.

The filter cartridge should be replaced
when the replacement indicator light turns
red or if the flow of water to the dispenser
or icemaker decreases.

Installing the Filter Cartridge

If you are replacing the cartridge, first
remove the old one by slowly turning
it to the left. Do not pull down on the
cartridge. A small amount of water
may drip down.

Fill the replacement cartridge with
water from the tap to allow for better
flow from the dispenser immediately
after installation.

Lining up the arrow on the cartridge
and the cartridge holder, place the
top of the new cartridge up inside
the holder. Do not push it up into
the holder.

Slowly turn it to the right until the filter
cartridge stops. DO NOT OVERTIGHTEN.
As you turn the cartridge, it will
automatically raise itself into position.
Cartridge will rotate about 1/4 turn.

Run water from the dispenser for
3 minutes (about one and a half
gallons) to clear the system and
prevent sputtering.

Press and hold the RESET WATER FILTER
pad on the dispenser for 3 seconds.

NOTE: A newly-installed water filter
cartridge may cause water to spurt from
the dispenser.

Filter Bypass Plug

You must use the filter bypass plug
when a replacement filter cartridge is not
available. The dispenser and the icemaker
will not operate without the filter or filter
bypass plug.

Replacement Filters:

To order additional filter cartridges
in the United States, visit our Website,
www.GEAppliances.com, or call GE Parts
and Accessories, 800.626.2002.

GWF
Suggested Retail $34.95 USD

Customers in Canada should consult
the yellow pages for the nearest Camco
Service Center.

Place the top of the cartridge up
inside the cartridge holder and
slowly turn it to the right.

Filter Bypass Plug

Cartridge
Holder

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

8

About the shelves, bins and racks.

Refrigerator Door Bins and Freezer Door Tilt-Out Bins

Large Bins

The larger refrigerator door bins and
freezer tilt-out door bins are adjustable.

To remove: Lift the front of the bin straight
up, then lift up and out.

To replace or relocate: Engage the back side
of the bin in the molded supports of the
door. Then push down on the front of the
bin. Bin will lock in place.

Small Bins

To remove: Lift the front of the bin straight

up then out.

To replace: Position the bin above the
rectangular molded supports on the door.
Then slide the bin down onto the support
to lock it in place.

The snugger helps prevent tipping, spilling
or sliding of small items stored on the door
shelf. Place a finger on either side of the
snugger near the rear and move it back
and forth to fit your needs.

CAUTION: Be
careful when placing
items in the top bin.
Make sure that
items do not block
or fall into the ice
chute.

Not all features are on all models.

Refrigerator bin

Freezer tilt-out bin

Snugger

Door Wine/Beverage Rack (on some models)

This rack holds up to 5 cans, one bottle of
wine or one 2-liter bottle of soda.

The rack hangs from the sides of the
dairy bin.

To remove:

Empty the wine/beverage rack.

Holding the bottom of the dairy bin,

lift the front straight up, then lift up

and out.

To detach the rack from the dairy bin,

pull the rack’s side wires out of the

holes on each side of the dairy bin.

To replace:

Reattach the rack to the sides
of the bin.

Engage the back side of the bin in
the molded supports on the door.
Then push down on the front of the
bin. The bin will lock into place.

Do not block

www.GEAppliances.com

QuickSpace™Shelf

This shelf splits in half and slides under
itself for storage of tall items on the shelf
below.

This shelf can be removed and replaced
or relocated just like Slide-Out Spillproof
Shelves.

On some models, this shelf can not be used
in the lowest position.

Slide-Out Spillproof Shelf

The slide-out spillproof shelf allows you
to reach items stored behind others. The
special edges are designed to help prevent
spills from dripping to lower shelves.

To remove:

Slide the shelf out until it reaches the stop,
then press down on the tab and slide the
shelf straight out.

To replace or relocate:

Line the shelf up with the supports and
slide it into place. The shelf can be
repositioned when the door is at 90° or
more. To reposition the shelf, slide the shelf
past the stops and angle downward. Slide
shelf down to the desired position, line up
with the supports and slide into place.

Make sure you push the shelves all the way back
in before you close the door.

Slide-Out Freezer Shelves

To remove, slide out to the stop position,

lift the front past the stop position, and
slide out.

Make sure you push the shelves all the way back
in before you close the door.

Freezer Baskets

To remove, slide out to the stop position,

lift the front past the stop position, and
slide out.

On some models, the full extension basket
can be removed by pushing the basket all

the way to the back of the freezer. Lift up
until the back pins are disengaged. Lift the
entire basket up and pull out.

Make sure you push the baskets all the way back
in before you close the door.

Press tab and pull shelf
forward to remove

Fixed Freezer Shelves

To remove, lift the shelf up at the left side

and then bring the shelf out.

NOTE FOR DISPENSER MODELS: In order
to take full advantage of the tilt-out ice bin,
only store items on the shelf below the ice
bin that are no taller than the lowest point
on the bin.

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

9

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

10

About the refrigerator doors.

Refrigerator Doors

The refrigerator doors may feel different
than the ones you are used to. The special
door opening/closing feature makes sure
the doors close all the way and are securely
sealed.

When opening and closing the door you
will notice a stop position. If the door is
opened past this stop point, the door will
remain open to allow you to load and
unload food more easily. When the door
is only partially open, it will automatically
close.

The resistance you feel at the stop
position will be reduced as the door
is loaded with food.

When the door is only partially open,
it will automatically close.

Beyond this stop the door will stay open.

Door Alignment

If doors are uneven, adjust the refrigerator
door.

Using a 7/16″ wrench, turn the door
adjusting screw to the right to raise the
door, to the left to lower it. (A nylon
plug, imbedded in the threads of the
pin, prevents the pin from turning
unless a wrench is used.)

After one or two turns of the wrench,
open and close the refrigerator door
and check the alignment at the top of
the doors.

7/16″ Wrench

Raise

11

About the crispers and pans. www.GEAppliances.com

Not all features are on all models.

Fruit and Vegetable Crispers

Excess water that may accumulate in the
bottom of the drawers should be wiped dry.

On some models, the bottom drawer has
full extension slides that allow full access
to the drawer.

Adjustable Humidity Crispers

Slide the control all the way to the
HI setting to provide high humidity
recommended for most vegetables.

Slide the control all the way to the
LO setting to provide lower humidity
levels recommended for most fruits.

Convertible Deli Pan

The convertible deli pan has its own cold
air duct to allow a stream of cold air from
the freezer compartment to flow to the pan.

The variable temperature control regulates
the airflow from the Climate Keeper.

Set the control to the coldest setting to store
fresh meats.

Set the control to cold to convert the pan
to normal refrigerator temperature and
provide extra vegetable storage space. The
cold air duct is turned off. Variable settings
between these extremes can be selected.

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

About crisper removal.

Not all features are on all models.

Crisper Removal

The top crispers can easily be removed by
pulling the drawer straight out and lifting
the drawer up and over the stop location.

If the door prevents you from taking out
the drawers, first try to remove the door
bins. If this does not offer enough
clearance, the refrigerator will need to
be rolled forward until the door opens
enough to slide the drawers out. In some
cases, when you roll the refrigerator out,
you will need to move the refrigerator
to the left or right as you roll it out.

To remove the bottom crisper:

Pull the drawer out to the stop position.

Rotate all four swing locks to the unlock

position.

Lift the front of the drawer up and out.

To replace the bottom crisper:

Make sure all four swing locks are in

the unlock position.

Place the sides of the drawer into the

drawer supports, making sure the swing

locks fit on the drawer slots.

Lock all four swing locks by rotating

them to the lock position.

HI LO

C

O

D

L

O

C

L

D

E

S

T

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

12

About the automatic icemaker.

Automatic Icemaker

The icemaker will produce seven cubes
per cycle—approximately 100–130 cubes
in a 24-hour period, depending on freezer
compartment temperature, room
temperature, number of door openings
and other use conditions.

If the refrigerator is operated before the
water connection is made to the icemaker,
set the power switch in the O (off) position.

When the refrigerator has been connected
to the water supply, set the power switch to
the l (on) position.

The icemaker will fill with water when it
cools to 15°F (–10°C). A newly installed
refrigerator may take 12 to 24 hours to begin
making ice cubes.

You will hear a buzzing sound each time
the icemaker fills with water.

Throw away the first few batches of ice to
allow the water line to clear.

Be sure nothing interferes with the sweep
of the feeler arm.

When the bin fills to the level of the feeler
arm, the icemaker will stop producing
ice. It is normal for several cubes to be
joined together.

If ice is not used frequently, old ice cubes
will become cloudy, taste stale and shrink.

Special notes about dispenser models:

■ Dispenser models have a tilt-out ice bin.

The bin can be tilted out as shown in
the illustrations, and it will hold itself
up while you take ice out or turn the
icemaker power switch on and off.
Be sure to put the bin back in place
before closing the door.

■ To restore your ice level from an empty

bucket stage, the following steps are
recommended:

12 hours after the first batch of ice
has fallen into the bin, dispense
3 to 4 cubes.

After an additional 6 hours, dispense
3 to 4 cubes again.

These steps will restore your ice level
in the shortest amount of time.

NOTE: In homes with lower-than-average water
pressure, you may hear the icemaker cycle multiple
times when making one batch of ice.

A newly installed refrigerator may take 12 to 24 hours to begin making ice.

Lift the bin, then pull it
forward until the bin stops.

Removing Ice Bin (dispenser models)

CAUTION: The ice bin is heavy when full.

Set the power switch to the O (off) position
before removing the bin.

When replacing the bin, be sure to press it
firmly into place. If it does not go all the
way back, remove it and rotate the drive
mechanism 1/4 turn. Then push the bin
back again.

Icemaker

Feeler Arm

Power
Switch

Green
Power Light

Lower the bin to access ice
or reach the power switch.

NOTE: In order to take full advantage
of the tilt-out ice bin, only store items
on the shelf below the ice bin that
are no taller than the lowest point
on the bin.

On dispenser models, to
access ice or reach the
power switch:

Lift the bin, then pull it
forward until the bin stops.

Lift and pull forward again
to remove the bin.

Rotate

Drive
Mechanism

Dispenser Models only

About the ice and water dispenser. (on some models) www.GEAppliances.com

On some models

To Use the Dispenser

Select CUBED ICE , CRUSHED ICE
or WATER .

Press the glass gently against the top of the
dispenser cradle.

The spill shelf is not self-draining. To
reduce water spotting, the shelf and its
grille should be cleaned regularly.

If no water is dispensed when the refrigerator is
first installed, there may be air in the water line
system. Press the dispenser arm for at least two
minutes to remove trapped air from the water
line and to fill the water system. To flush out
impurities in the water line, throw away the first
six glassfuls of water.

CAUTION: Never put fingers or any other
objects into the ice crusher discharge opening.

Locking the Dispenser

Press the LOCK CONTROL
pad for 3 seconds to
lock the dispenser and
control panel. To
unlock, press and
hold the pad again
for 3 seconds.

Dispenser Light

This pad turns the night
light in the dispenser on

and off. The light also
comes on when the
dispenser cradle is
pressed. If this light
burns out, it should be
replaced with a 6 watt
12 V maximum bulb.

Quick Ice

When you need ice
in a hurry, press this
pad to speed up ice
production. This will
increase ice production
for the following
48 hours or until you
press the pad again.

Door Alarm

To set the alarm, press
this pad until the
indicator light comes
on. This alarm will
sound if either door is
open for more than
3 minutes. The light
goes out and the
beeping stops when
you close the door.

Spill Shelf

Important Facts About Your Dispenser

■ Do not add ice from trays or bags to

the storage drawer. It may not crush or
dispense well.

■ Avoid overfilling glass with ice and use

of narrow glasses. Backed-up ice can jam
the chute or cause the door in the chute
to freeze shut. If ice is blocking the
chute, poke it through with a wooden
spoon.

■ Beverages and foods should not be

quick-chilled in the ice storage drawer.
Cans, bottles or food packages in the
storage drawer may cause the icemaker
or auger to jam.

■ To keep dispensed ice from missing

the glass, put the glass close to, but not
touching, the dispenser opening.

■ Some crushed ice may be dispensed even

though you selected CUBED ICE. This
happens occasionally when a few cubes
accidentally get directed to the crusher.

■ After crushed ice is dispensed, some

water may drip from the chute.

■ Sometimes a small mound of snow will

form on the door in the ice chute. This
condition is normal and usually occurs
when you have dispensed crushed ice
repeatedly. The snow will eventually
evaporate.

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

13

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

Cleaning the Outside

The dispenser drip area, (on some models)

beneath the grille, should be wiped dry. Water
left in this area may leave deposits. Remove
the deposits by adding undiluted vinegar to
the well. Soak until the deposits disappear
or become loose enough to rinse away.

The dispenser cradle (on some models).
Before cleaning, lock the dispenser by
pressing and holding the LOCK CONTROL
pad for 3 seconds. Clean with warm
water and baking soda solution–about
a tablespoon (15 ml) of baking soda to
a quart (1 liter) of water. Rinse thoroughly
and wipe dry.

The door handles and trim. Clean with
a cloth dampened with soapy water.
Dry with a soft cloth.

The stainless steel panels and door handles

(on some models) can be cleaned with a
commercially available stainless steel
cleaner such as Stainless Steel Magic.

™

Stainless Steel Magic is available at Ace, True
Value, Servistar, HWI and other leading
stores. It is also available through GE Parts
and Accessories, 800.626.2002. Order part
number WX10X15.

Do not use appliance wax or polish on the
stainless steel.

Keep the outside clean. Wipe with a clean
cloth lightly dampened with kitchen
appliance wax or mild liquid dish detergent.
Dry and polish with a clean, soft cloth.

Do not wipe the refrigerator with a soiled dish
cloth or wet towel. These may leave a residue
that can erode the paint. Do not use scouring
pads, powdered cleaners, bleach or cleaners
containing bleach because these products can
scratch and weaken the paint finish.

Cleaning the Inside

To help prevent odors, leave an open box of

baking soda in the fresh food and freezer
compartments.

Unplug the refrigerator before cleaning. If this
is not practical, wring excess moisture out
of sponge or cloth when cleaning around
switches, lights or controls.

Use warm water and baking soda solution–
about a tablespoon (15 ml) of baking soda
to a quart (1 liter) of water. This both cleans
and neutralizes odors. Rinse and wipe dry.

Use of any cleaning solution other than that
which is recommended, especially those that
contain petroleum distillates, can crack or
damage the interior of the refrigerator.

Avoid cleaning cold glass shelves with hot water
because the extreme temperature difference
may cause them to break. Handle glass shelves
carefully. Bumping tempered glass can cause
it to shatter.

Do not wash any plastic refrigerator parts in
the dishwasher.

Dispenser drip area.

14

Care and cleaning of the refrigerator.

For long vacations or absences, remove
food and unplug the refrigerator. Clean
the interior with a baking soda solution
of one tablespoon (15 ml) of baking soda
to one quart (1 liter) of water. Leave the
doors open.

Set the icemaker power switch to the
O (off) position and shut off the water supply
to the refrigerator.

If the temperature can drop below freezing,
have a qualified servicer drain the water
supply system (on some models) to prevent
serious property damage due to flooding.

15

www.GEAppliances.com

Behind the Refrigerator

Be careful when moving the refrigerator
away from the wall. All types of floor
coverings can be damaged, particularly
cushioned coverings and those with
embossed surfaces.

Pull the refrigerator straight out and return
it to position by pushing it straight in.
Moving the refrigerator in a side direction
may result in damage to the floor covering
or refrigerator.

When pushing the refrigerator back, make sure
you don’t roll over the power cord or icemaker
supply line (on some models).

Preparing for Vacation

Preparing to Move

Secure all loose items such as shelves and
drawers by taping them securely in place
to prevent damage.

When using a hand truck to move the
refrigerator, do not rest the front or back
of the refrigerator against the hand truck.
This could damage the refrigerator. Handle
only from the sides of the refrigerator.

Be sure the refrigerator stays in an upright
position during moving.

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

16

Replacing the light bulbs.

Setting the controls to OFF does not remove power to the light circuit.

Refrigerator Compartment—Upper Light

Unplug the refrigerator.

The bulbs are located at the top of the
compartment, inside the light shield.
On some models, a screw at the front of
the light shield will have to be removed.

To remove the light shield, on some
models, press in on the tabs on the
sides of the shield and slide forward
and out. On other models, just slide
forward and out.

After replacing the bulb with an
appliance bulb of the same or lower
wattage, replace the light shield and
screws (on some models). When
replacing the light shield, make sure
that the tabs at the back of the shield
fit into the slots at the back of the light
shield housing.

Plug the refrigerator back in.

Refrigerator Compartment—Lower Light

This light is located above the top drawer.

Unplug the refrigerator.

Remove the convertible meat drawer
control knob by pulling straight out.

Lift the light shield up and pull it out.

After replacing the bulb with an
appliance bulb of the same or lower
wattage, replace the shield and
the knob.

Plug the refrigerator back in.

Freezer Compartment

Unplug the refrigerator.

Remove the shelf just above the light
shield. (The shelf will be easier to
remove if it is emptied first.) On some
models, a screw at the top of the light
shield will need to be removed.

To remove the light shield, press in
on the sides, and lift up and out.

Replace the bulb with an appliance
bulb of the same or lower wattage,
and reinstall the light shield. When
reinstalling the light shield, make
sure the top tabs snap securely
into place. Replace the screw
(on some models).

Reinstall the shelf and plug the
refrigerator back in.

Dispenser (on some models)

Unplug the refrigerator.

The bulb is located on the dispenser
under the control panel.
Remove the light bulb by turning
it counterclockwise.

Replace the bulb with a bulb of the
same size and wattage.

Plug the refrigerator back in.

Tabs

C

O

L

D

D

L

E

O

S

C

T

1/4″ (6 mm) Max.

Panels thicker than 1/4″ (6 mm)

5/16″ (8 mm)

3/4″ (19 mm)

17

Trim kits and decorator panels.

For CustomStyle™models

Read these instructions completely and carefully.

Before You Begin

2″ (5.1 cm)
Clearance
Handle Side

Appearance
Panel

Refrigerator
Door

1/4″ (6 mm)
Thick Backing

3/4″
(19 mm)

3/4″ (19 mm) or Raised Panel

A raised panel design screwed or glued to a 1/4″ (6 mm) thick backing, or a 3/4″ (19 mm) routed board
can be used. The raised portion of the panel must be fabricated to permit clearances of at least 2″ (5.1 cm)
from the handle side for fingertip clearance.

Panels thicker than 1/4″ (6 mm), up to 3/4″ (19 mm) maximum, will require that the outer 5/16″
(8 mm) of panel perimeter be no thicker than 1/4″ (6 mm).

Weight limitations for custom panels:
Fresh Food 38 lbs. (17 kg) max.
Freezer Door 28 lbs. (13 kg) max.

1/4″ (6 mm) Max.

Panels 1/4″ (6 mm) thick or less

Some models are equipped with trim kits that allow you to install door panels. You can order
pre-cut black, white, bisque or stainless steel decorator panels from GE Parts and Accessories,

800.626.2002, or you can add wood panels to match your kitchen cabinets.

Panels less than 1/4″ (6 mm) thick

When installing wood panels less than 1/4″ (6 mm) thick, you need to create a filler panel, such as 1/8″
(3 mm) cardboard, that will fit between the face of the door and the wood panel. If you are installing the
pre-cut decorator panels, pre-cut filler panels are included in the kit. The combined thickness of the
decorator or wood panel and the filler panel should be 1/4″ (6 mm).

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

18

Trim kits and decorator panels.

Freezer Panel

Without Dispenser

Freezer Panel

With Dispenser Fresh Food Panel

Cutout

5/16″

(8 mm)

1415⁄32″

(36.8 cm)

679⁄32″

(170.9 cm)

1/8″ (3 mm)

FRONT

177⁄8″

(45.4 cm)

1415⁄32″

(36.8 cm)

335⁄8″

(85.4 cm)

FRONT

679⁄32″

(170.9 cm)

1915⁄32″

(49.5 cm)

FRONT

23‘ Dimensions for Custom Wood Panels

The areas at the top of the panels need to be cut out of the panels.

25‘

CustomStyle™Dimensions for Custom Wood Panels

The areas at the top of the panels need to be cut out of the panels.

Cutout

1/8″ (3 mm)

Cutout

1/8″ (3 mm)

5/16″

(8 mm)

5/16″

(8 mm)

Freezer Panel

Without Dispenser

Freezer Panel

With Dispenser Fresh Food Panel

Cutout

5/16″

(8 mm)

1415⁄32″

(36.8 cm)

69″

(175.3 cm)

1/8″ (3 mm)

FRONT

17″

(43.2 cm)

1415⁄32″

(36.8 cm)

361⁄4″

(92.0 cm)

FRONT

69″

(175.3 cm)

1915⁄32″

(49.5 cm)

FRONT

Cutout

1/8″ (3 mm)

Cutout

1/8″ (3 mm)

5/16″

(8 mm)

5/16″

(8 mm)

19

Inserting the door panels.

Read these instructions completely and carefully.

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

Attach the Top Trim on the Freezer and Fresh Food Doors.

The Top Trim can be found inside the refrigerator
compartment.

With a T-20 Torxdriver, attach the Top Trim, using
two screws on each Top Trim piece, to the top of

each door. Hand tighten only. Make sure that the
top of each panel fits snugly behind the lip of the
Top Trim.

Insert the Freezer Panel and Fresh Food Panel.

Carefully push the freezer panel in until it slides
into the slot behind the door handle. Push the filler
panel (required with some door panels) in behind
the decorator panel. Repeat for fresh food panel.

If your model has a dispenser, this step only applies
to the fresh food panel and top freezer panel.

Insert the Bottom Freezer Panel (on dispenser models).

Carefully push the panel in until it slides into the
slot behind the door handle. Push the filler panel

(required with some door panels) in behind the
decorator panel.

Cut-Out

Cut-Out

Top Trim Screws

Top
Freezer
Panel

Bottom
Freezer
Panel

Side Trim

Side Trim

Fresh
Food
Panel

Top Trim Screws

20

Inserting the door panels.

Install the Side Trim.

These pieces are tucked inside the refrigerator door
handle.

Do not remove the protective film on the outside of the
Side Trim until the Side Trim is installed.

Fit the bottom of the Side Trim under the Bottom
Trim as illustrated.

Hold the Side Trim against the front face of the
decorator panels and fit the Side Trim under
the Top Trim. Make sure the magnetically attached
Side Trim is fitted correctly and that you are
satisfied with the appearance of all the parts.

Consumer Support

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

Side
Trim

Side
Trim

Bottom Trim

Top Trim

21

BEFORE YOU BEGIN

Read these instructions completely
and carefully.

•

IMPORTANT — Save these

instructions for local inspector’s use.

•

IMPORTANT — Observe all

governing codes and ordinances.

• Note to Installer – Be sure to leave these
instructions with the Consumer.

• Note to Consumer – Keep these
instructions for future reference.

• Skill level – Installation of this appliance
requires basic mechanical skills.

• Completion time – Refrigerator Installation

30 minutes
Water Line Installation

30 minutes

• Proper installation is the responsibility of
the installer.

• Product failure due to improper installation
is not covered under the Warranty.

If the refrigerator has already been installed,
remove the base grille (see Step 2 in Moving

the Refrigerator), then skip to Step 5 in
Installing the Refrigerator.

Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: GEAppliances.com

In Canada, call 1.800.361.3400 or Visit our Website at: geappliances.ca

Installation

Refrigerator

Instructions

Models 23, 25, 26, 27 & 29

If the refrigerator has an icemaker, it will have
to be connected to a cold water line. A GE
water supply kit (containing tubing, shutoff
valve, fittings and instructions) is available at
extra cost from your dealer, by visiting our
Website at GEAppliances.com (in Canada
at geappliances.ca) or from Parts and
Accessories, 800.626.2002 (in Canada

1.888.261.3055).

PREPARATION

WATER SUPPLY TO THE ICEMAKER

TOOLS YOU WILL NEED

Phillips Head Screwdriver

3/8″ and 5/16″ Socket 1/2″ and 7/16″ Wrench

Plastic Putty Knife

1/8″ Hex Wrench

22

Installation Instructions

LOADING THE RERIGERATOR
ONTO A HAND TRUCK

Leave all tape and door pads on doors
until the refrigerator is in its final location.

To move the refrigerator, use a padded
hand truck. Center the refrigerator on the
hand truck and secure the strap around
the refrigerator. DO NOT OVERTIGHTEN

THE STRAP.

1

REMOVE THE BASE GRILLE

Remove the grille by removing the two
Phillips head screws.

2

If the refrigerator must go through
any entrance that is less than 38″
wide, the doors must be removed.
Proceed to Step 3.

DO NOT remove the handles.

If all entrances are more than
38″ wide, skip to Installing
the Refrigerator.

DISCONNECT THE WATER
COUPLING (on some models)

If the refrigerator has a water dispenser,

there is a water line from the cabinet into
the bottom hinge on the freezer door that
must be disconnected.

To disconnect, push in on the white collar
of the coupling and pull out the tubing.

3

White collar

Bottom
freezer
hinge

MOVING THE REFRIGERATOR

23

Installation Instructions

DISCONNECT THE POWER
COUPLING (on some models)

If the refrigerator has a water dispenser,

there is a power line (harness) from the
cabinet into the bottom hinge on the
freezer door that must be disconnected.

To disconnect, pull apart at the coupling.

4

Bottom
freezer
hinge

DISCONNECT THE ELECTRICAL
CONNECTORS (on some models)

If the refrigerator has a refreshment
center, there are electrical connectors

(harnesses) from the cabinet into the
bottom hinge on the refrigerator door
that must be disconnected.

To disconnect, pull apart each connector.

5

Bottom
refrigerator
hinge

CLOSE THE FREEZER AND
REFRIGERATOR DOORS

6

REMOVE THE FREEZER DOOR

Remove the freezer door top hinge cover
(if equipped) by either squeezing it and
pulling it up or by prying it off with a
plastic putty knife.

Remove the two 5/16″ or 1/8″ hex head
screws, then lift the hinge straight up to
free the hinge pin.

Open the freezer door to 90.°

7

A

C

B

5/16″ or 1/8″ hex head

90°

24

Installation Instructions

MOVING THE REFRIGERATOR (CONT.)

REMOVE THE FREEZER DOOR
(cont.)

As one person slowly lifts the freezer door
up and off the bottom hinge, the second
person should carefully guide the water
line and power line (harness) through the
bottom hinge.

Set the door on a non-scratching surface
with the inside up.

7

D

E

90°

REMOVE THE REFRIGERATOR
DOOR

Remove the refrigerator door top hinge
cover (if equipped) by either squeezing it
and pulling it up or by prying it off with
a plastic putty knife.

8

A

REMOVE THE REFRIGERATOR
DOOR (cont.)

Remove the two 5/16″ or 1/8″ hex head
screws, then lift the hinge straight up to
free the hinge pin.

Open the refrigerator door to 90.°

8

B

C

5/16″ or 1/8″ hex head

90°

25

Installation Instructions

REMOVE THE
REFRIGERATOR DOOR (cont.)

Lift the refrigerator door up and off the
bottom hinge.

If the refrigerator has a refreshment
center, one person should slowly lift the

door up and off the bottom hinge and the
second person should carefully guide the
electrical lines (harnesses) through the
bottom hinge.

Set the door on a non-scratching surface
with the inside up.

8

D

E

90°

REPLACING THE DOORS

To replace the doors, simply reverse
steps 3 through 8.

However, please note the following:

• When lowering the doors onto the
bottom hinges, make sure the second
person carefully guides the tube and
harnesses through the holes in the
hinges.

• When connecting the water line, make
sure you insert the tubing all the way
to the mark.

• Do not pinch the tubing and harnesses
when placing the doors on the bottom
hinges.

• When connecting the power line and
the electrical lines (refreshment center
models only), be sure that the
connectors are seated together fully.

9

Mark

Refreshment Center Models only

26

DIMENSIONS AND SPECIFICATIONS
(for 23‘ CustomStyle

™

models)

DIMENSIONS AND SPECIFICATIONS

Installation Instructions

INSTALLING THE REFRIGERATOR

REFRIGERATOR LOCATION

• Do not install the refrigerator where the
temperature will go below 60°F (16°C)
because it will not run often enough to
maintain proper temperatures.

• Do not install the refrigerator where the
temperature will go above 100°F (37°C)
because it will not perform properly.

• Install it on a floor strong enough to
support it fully loaded.

CLEARANCES

Allow the following clearances for ease
of installation, proper air circulation and
plumbing and electrical connections:

23‘(33”wide),

23‘/25‘ CustomStyle

™

25‘, 26‘, 27‘, 29‘

Sides 1/8″ (4 mm) 1/8″ (4 mm)

Top 1″ (25 mm) 1″ (25 mm)

Back 1/2″ (13 mm) 1″ (25 mm)

701⁄4″ (178.4 cm)

36″

(91.4 cm)

24″ (61 cm)

24″ (61 cm)
Cabinet

Water Electrical

3/4″ (19 mm) Airspace
(1/2″ [13 mm] Gap +
1/4″ [6 mm] Wall Plates)

25″ (63.5 cm)
Countertop

DIMENSIONS AND SPECIFICATIONS
(for 25‘ CustomStyle

™

models)

*721/4″ (183.5 cm) required for full adjustment

of mobility wheels. If cabinets installed
above refrigerator have doors that are
flush to the top of the opening for the
refrigerator, then an additional 1/8″ may be
required to provide clearance for cabinet
doors to open freely.

36″

(91.4 cm)

24″ (61 cm)

721⁄4″ (183.5 cm)*

27

Installation Instructions

CONNECTING THE REFRIGERATOR
TO THE HOUSE WATER LINE
(icemaker and dispenser models)

A cold water supply is required for
automatic icemaker and dispenser
operation. If there is not a cold water
supply, you will need to provide one.
See “Installing the Water Line” section.

NOTES:

• Before making the connection to the
refrigerator, be sure the refrigerator
power cord is not plugged into the wall
outlet.

• If your refrigerator does not have a
water filter, we recommend installing
one if your water supply has sand or
particles that could clog the screen of
the refrigerator’s water valve. Install it
in the water line near the refrigerator.
If using GE SmartConnect

™

Refrigerator
Tubing Kit, you will need an additional
tube (WX08X10002) to connect the filter.
Do not cut plastic tube to install filter.

If you are using copper tubing, place a
compression nut and ferrule (sleeve) onto
the end of the tubing coming from the
house cold water supply.

If you are using the GE SmartConnect

™

tubing, the nuts are already assembled to

the tubing.
If you are using copper tubing, insert

the end of the tubing into the refrigerator
connection, at the back of the refrigerator,
as far as possible. While holding the
tubing, tighten the fitting.

If you are using GE SmartConnect

™

tubing, insert the molded end of the

tubing into the refrigerator connection,
at the back of the refrigerator, and tighten
the compression nut until it is hand tight.
Then tighten one additional turn with a
wrench. Overtightening may cause leaks.

1

A

B

Fasten the tubing into the clamp provided
to hold it in position. You may need to pry
open the clamp.

1/4″ Tubing

Tubing Clamp

1/4″
Compression Nut

Ferrule
(sleeve)

SmartConnect™Tubing

Refrigerator
Connection

C

TURN ON THE WATER SUPPLY

Turn the water on at the shutoff valve
(house water supply) and check for
any leaks.

2

PLUG IN THE REFRIGERATOR

Before plugging in the refrigerator, make
sure the icemaker power switch is set to
the O (off) position.

See the grounding information attached
to the power cord.

3

28

LEVEL THE REFRIGERATOR
(cont.)

To adjust the
rollers on 23

‘/25‘

CustomStyle

™

models:

Turn the front roller
adjusting screws

clockwise to raise

the refrigerator,

counterclockwise
to lower it. Use a 3/8″ hex wrench with

extension, or an adjustable wrench.

These models also have rear adjustable
rollers so you can align the refrigerator
with your kitchen cabinets. Use a 3/8″ hex
wrench with extension to turn the screws
for the rear rollers—clockwise to raise the
refrigerator, counterclockwise to lower it.

Installation Instructions

INSTALLING THE REFRIGERATOR (CONT.)

PUT THE REFRIGERATOR
IN PLACE

Move the refrigerator to its final location.

4 5

LEVEL THE REFRIGERATOR

The refrigerator can be leveled by
adjusting the rollers located near the
bottom hinges.

Rollers have three purposes:

• Rollers adjust so the door closes easily
when opened about halfway. (Raise the
front about 5/8″ [16 mm] from the floor.)

• Rollers adjust so the refrigerator is
firmly positioned on the floor and does
not wobble.

• Rollers allow you to move the
refrigerator away from the wall for
cleaning.

To adjust the rollers on 23‘ (33” wide),
25‘, 26‘, 27‘ and 29‘ models:

• Turn the roller
adjusting screws

clockwise to
raise the

refrigerator,

counterclockwise
to lower it. Use

a 3/8″ hex socket
or wrench, or
an adjustable
wrench.

5

Rollers

Roller adjusting screw

Roller adjusting screws

LEVEL THE DOORS

Adjust the refrigerator door to make the
doors even at the top.

To align:

Using a 7/16″ wrench, turn the door
adjusting screw to the right to raise the
door, to the left to lower it.

NOTE:

A nylon plug, imbedded in the threads
of the pin, prevents the pin from turning
unless a wrench is used.

After one or two turns of the wrench,
open and close the refrigerator door and
check the alignment at the top of the doors.

6

A

B

Doors should be even at top

Raise

7/16″ wrench

Raise

29

Installation Instructions

REPLACE THE BASE GRILLE

Replace the grille by installing the two
Phillips head screws.

7

SET THE CONTROLS

Set the controls to the recommended
setting.

8

START THE ICEMAKER

Set the icemaker power switch to the
I (on) position. The icemaker will not
begin to operate until it reaches its
operating temperature of 15°F (–9°C)
or below. It will then begin operation
automatically. It will take 2–3 days to
fill the ice bin.

NOTE:

In lower water pressure conditions, the
water valve may turn on up to 3 times
to deliver enough water to the icemaker.

9

Power
switch

30

INSTALLING THE WATER LINE (ICEMAKER & DISPENSER MODELS)

Recommended copper water supply kits are
WX8X2, WX8X3 or WX8X4, depending on the
amount of tubing you need. Approved plastic
water supply lines are GE SmartConnect

™

Refrigerator Tubing (WX08X10002,
WX08X10006, WX08X10015 and
WX08X10025).

When connecting your refrigerator to a GE
Reverse Osmosis Water System, the only
approved installation is with a GE RVKit. For
other reverse osmosis water systems, follow
the manufacturer’s recommendations.

If the water supply to the refrigerator is from
a Reverse Osmosis Water Filtration System
AND the refrigerator also has a water filter,
use the refrigerator’s filter bypass plug. Using
the refrigerator’s water filtration cartridge in
conjunction with the RO filter can result in
hollow ice cubes and slower water flow from
the water dispenser.

This water line installation is not warranted
by the refrigerator or icemaker manufacturer.
Follow these instructions carefully to
minimize the risk of expensive water damage.

Water hammer (water banging in the pipes)
in house plumbing can cause damage to
refrigerator parts and lead to water leakage
or flooding. Call a qualified plumber to correct
water hammer before installing the water
supply line to the refrigerator.

To prevent burns and product damage, do not
hook up the water line to the hot water line.

If you use your refrigerator before connecting
the water line, make sure the icemaker power
switch is in the O (off) position.

Do not install the icemaker tubing in areas
where temperatures fall below freezing.

When using any electrical device (such as a
power drill) during installation, be sure the
device is double insulated or grounded in a
manner to prevent the hazard of electric
shock, or is battery powered.

All installations must be in accordance with
local plumbing code requirements.

BEFORE YOU BEGIN

Installation Instructions

WHAT YOU WILL NEED

• Copper or GE SmartConnect™Refrigerator

Tubing kit, 1/4″ outer diameter to connect

the refrigerator to the water supply. If using
copper, be sure both ends of the tubing are
cut square.

To determine how much tubing you need:
measure the distance from the water valve on
the back of the refrigerator to the water
supply pipe. Then add 8′ (2.4 m). Be sure
there is sufficient extra tubing (about 8′ [2.4 m]
coiled into 3 turns of about 10″ [25 cm]
diameter) to allow the refrigerator to move
out from the wall after installation.

GE SmartConnect

™

Refrigerator Tubing Kits

are available in the following lengths:
2′ (0.6 m) – WX08X10002

6′ (1.8 m) – WX08X10006
15′ (4.6 m) – WX08X10015
25′ (7.6 m) – WX08X10025

Be sure that the kit you select allows at least
8′ (2.4 m) as described above.