How it Works
GE
Loading...
197D3354P013
User Manual
80 pgs9.33 Mb0
Table of contents
Loading...

GE WX08X10006, 197D3354P013, WX08X10015, WX08X10025 User Manual

ge.com
Refrigerators
Top-Freezer
197D3354P013 49-60511 07-07 JR
Safety Instructions . . . . . . . . . . . .2–3

Operating Instructions

Additional Features . . . . . . . . . . . . . . . . .6
Controls . . . . . . . . . . . . . . . . . . . . . . . . . .4
Crispers and Pans . . . . . . . . . . . . . . . . . .6
Dispenser . . . . . . . . . . . . . . . . . . . . . . . . .7
Shelves and Bins . . . . . . . . . . . . . . . . . . .5
Water Filter . . . . . . . . . . . . . . . . . . . . . . .4

Care and Cleaning

Replacing the Light Bulbs . . . . . . . . . . .9

Installation Instructions

Preparing to Install
Reversing the Door Swing . . . . . . .14–18
Water Line Installation . . . . . . . . . .11–14
Troubleshooting Tips . . . . . . .19–21
Normal Operating Sounds . . . . . . . . . .19

Consumer Support

Consumer Support . . . . . . . . .Back Cover
Performance Data Sheet . . . . . . . . . . .27
Product Registration
Product Registration
for U.S. Customers . . . . . . . . . .22, 23, 24
State of California Water
Treatment Device Certificate . . . . . . . .28
Warranty for
Canadian Customers . . . . . . . . . . . . . . .25
Warranty for U.S. Customers . . . . . . . .26
Réfrigérateurs
Congélateur supérieur
Refrigeradores
Congelador superior
Model 18
Manuel d’utilisation
et d’installation
Owner’s Manual and
Installation Instructions
Manual del propietario
e instalación
La section française commence à la page 29
La sección en español empieza en la página 53
Nota al instalador – Asegúrese de
dejar estas instrucciones con el consumidor.
Nota al consumidor – Conserve
estas instrucciones para referencia futura.
Write the model and serial numbers here: Model # __________________________ Serial # __________________________
Find these numbers on the gray label on the left side, near the top of the refrigerator compartment.
Refrigerators
Top-Freezer
Note to Installer – Be sure to leave
these instructions with the Consumer.
Note to Consumer – Keep these
instructions for future reference.
Note à l’installateur – Assurez-vous de
laisser ces instructions au consommateur.
Note au consommateur – Conservez
ces instructions pour référence future.
Instructions de sécurité . . . .29–30

Instructions de fonctionnement

Bacs à légumes . . . . . . . . . . . . . . . . .33
Caractéristiques additionnelles . . . .33
Clayettes et bacs . . . . . . . . . . . . . . . .32
Distributeur . . . . . . . . . . . . . . . . . . . .34
Filtre à eau . . . . . . . . . . . . . . . . . . . .31
Machine à glaçons automatique . . .34
Réglages . . . . . . . . . . . . . . . . . . . . . .31

Soins et nettoyage

Remplacement des
ampoules électriques . . . . . . . . . . . .36
Soins et nettoyage . . . . . . . . . . . .35, 36

Instructions d’installation

Installation de la
conduite d’eau . . . . . . . . . . . . . .38–41
Inversion du sens
d’ouverture des portes . . . . . . . .41–45
Préparation à l’installation
du réfrigérateur . . . . . . . . . . . . . . . .37
En cas de panne . . . . . . . . .46–49
Bruits normaux
de fonctionnement . . . . . . . . . . . . . .46

Soutien au consommateur

Feuillet de données relatives à la
performance de la cartouche . . . . . . .51
Garantie . . . . . . . . . . . . . . . . . . . . . . .50
Soutien au consommateur . . . . . . . .52

Información de seguridad . . .53–54 Instrucciones de operación

Características adicionales . . . . . . . . . . .57
Controles . . . . . . . . . . . . . . . . . . . . . . . . .55
Dispensador . . . . . . . . . . . . . . . . . . . . . . .58
Estantes y compartimientos . . . . . . .56–57
Filtro de agua . . . . . . . . . . . . . . . . . . . . . .55
Gavetas de almacenamiento . . . . . . . . .57
Máquina de hielos automática . . . . . . .58

Cuidado y limpieza

Cómo reemplazar las bombillas . . . . . .60
Cuidado y limpieza . . . . . . . . . . . . . .58–60

Instrucciones para la instalación

Cómo invertir el vaivén de
la puerta . . . . . . . . . . . . . . . . . . . . . . .65–69
Instalación de la tubería
del agua . . . . . . . . . . . . . . . . . . . . . . .62–65
Preparación para instalar
el refrigerador . . . . . . . . . . . . . . . . . . . . .61
Consejos para la solución
de problemas . . . . . . . . . . . . . . .70–74
Sonidos normales de operación . . . . . .70

Soporte al consumidor

Hoja de datos de funcionamiento . . . .78
Garantía . . . . . . . . . . . . . . . . . . . . . . . . . .77
Soporte al consumidor . . . . . . . . . . . . . .79
Escriba aquí el modelo y el número de serie:
Modelo # ________________________________ Serie # __________________________________
Encuentre estos números en la etiqueta gris en el lado izquierdo, cerca de la parte superior del compartimiento del refrigerador.
Écrivez ici le numéro de modèle et le numéro de série :
Modèle # ______________________________ Série # ________________________________
Vous trouverez ces numéros sur l’étiquette grise située à gauche, près du haut du compartiment réfrigérateur.
IMPORTANT SAFETY INFORMATION. READ ALL INSTRUCTIONS BEFORE USING.
WARNING!
Use this appliance only for its intended purpose as described in this Owner’s Manual.
SAFETY PRECAUTIONS
When using electrical appliances, basic safety precautions should be followed, including the following:
■ This refrigerator must be properly installed
■
and located in accordance with the Installation Instructions before it is used.
■ Do not allow children to climb, stand or hang
■
on the shelves in the refrigerator. They could damage the refrigerator and seriously injure themselves.
■ Do not touch the cold surfaces in the freezer
■
compartment when hands are damp or wet. Skin may stick to these extremely cold surfaces.

Operating Instructions Safety InstructionsInstallation Instructions

■ Do not store or use gasoline or other flammable
■
vapors and liquids in the vicinity of this or any other appliance.
■ In refrigerators with automatic icemakers,
■
avoid contact with the moving parts of the ejector mechanism, or with the heating element located on the bottom of the icemaker. Do not place fingers or hands on the automatic icemaking mechanism while the refrigerator is plugged in.
■ Keep fingers out of the “pinch point” areas;
■
clearances between the doors and between the doors and cabinet are necessarily small. Be careful closing doors when children are in the area.
■ Unplug the refrigerator before cleaning and
■
making repairs.
NOTE: We strongly recommend that any servicing be performed by a qualified individual.
■ Setting either or both controls (some models only
■
have one control) to the 0 (off) position does not remove power to the light circuit.
■ Do not refreeze frozen foods which have
■
thawed completely.
DANGER! RISK OF CHILD ENTRAPMENT
PROPER DISPOSAL OF THE REFRIGERATOR
Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous…even if they will sit for “just a few days.” If you are getting rid of your old refrigerator, please follow the instructions below to help prevent accidents.
Before You Throw Away Your Old Refrigerator or Freezer:
■ Take off the doors.
■ Leave the shelves in place so that children
may not easily climb inside.
Refrigerants
All refrigeration products contain refrigerants, which under federal law must be removed prior to product disposal. If you are getting rid of an old refrigeration product, check with the company handling the disposal about what to do.
USE OF EXTENSION CORDS
Because of potential safety hazards under certain conditions, we strongly recommend against the use of an extension cor
However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed (in the United
Consumer Support Troubleshooting Tips
2
States) or a CSA-listed (in Canada), 3-wire grounding type appliance extension cord having a grounding type plug and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 120 volts.
d.
WARNING!
HOW TO CONNECT ELECTRICITY
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For personal safety, this appliance must be properly grounded.
ge.com
The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a standard 3-prong (grounding) wall outlet to minimize the possibility of electric shock hazard from this appliance.
Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded.
Where a standard 2-prong wall outlet is encountered, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet.
The refrigerator should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating plate.
This provides the best performance and also prevents overloading house wiring circuits which could cause a fire hazard from overheated wires.
Never unplug your refrigerator by pulling on the power cord. Always grip plug firmly and pull straight out from the outlet.
Repair or replace immediately all power cords that have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end.
When moving the refrigerator away from the wall, be careful not to roll over or damage the power cord.
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
SAVE THESE INSTRUCTIONS
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions
3
About the controls on the refrigerator.
Control Settings
Initially, set the control(s) at 5 (some models have only one control). Allow 24 hours for the temperature to stabilize.
Several adjustments may be required. Adjust the control(s) one increment at a time and allow 12 hours after each adjustment for the refrigerator to reach the temperature you have set.
Setting the refrigerator control to 0 stops cooling in both the freezer and refrigerator compartments but does not shut off electrical power to the refrigerator. The freezer control (on some models) has no effect on electrical power to the refrigerator.
Control settings will vary based on personal preferences, usage and operating conditions, and may require more than one adjustment. Factors that affect temperature include the amount of food in the refrigerator or freezer, the frequency of door opening and the temperature of food when it is placed in the refrigerator.
Operating Instructions Safety InstructionsInstallation Instructions
About the water filter. (on some models)
(on some models)
Water Filter Cartridge
The water filter cartridge is located inside the cartridge holder in the back upper right corner of the refrigerator compartment.
NOTE: Some models ship with the filter bypass plug in place of the filter cartridge. The filter bypass plug needs to be removed before the filter cartridge is installed. Keep the filter bypass plug for future use.
When to Replace the Filter
The filter cartridge should be replaced every six months or earlier if the flow of water to the icemaker and dispenser decreases.
Installing the Filter
If you are replacing the cartridge, first remove the old one. To open the cartridge cover, push in where indicated and the cover will drop down.
Consumer Support Troubleshooting Tips
4
Cartridge
Remove the cartridge by slowly rotating it to the left. A small amount of water may drip down.
CAUTION:
has been trapped in the system, the filter cartridge may be ejected as it is removed. Use caution when removing.
Apply a month and year sticker to the new cartridge to remind you to replace it in six months.
If air
Filter Bypass Plug
You must use the filter bypass plug when a replacement filter cartridge is not available. The dispenser and the icemaker will not operate without the filter or filter bypass plug.
Replacement Filters
To order additional filter cartridges in the United States, visit our Website, ge.com, or call GE Parts and Accessories, 1.800.661.1616.
Filter Model GSWF Suggested Retail Price $34.95 USD
Customers in Canada should consult the yellow pages for the nearest Mabe Service Center
Position the cartridge inside the cartridge holder and slowly rotate the cartridge to the right until it stops. When the cartridge is properly installed, you will feel it “click” as it locks into place. The blade on the end of the cartridge should be positioned vertically. Do not overtighten.
Close the cartridge cover.
Run water from the dispenser for 3 minutes (about 1 the system and prevent sputtering. See T Dispenser section.
NOTE: A newly-installed water filter cartridge may cause water
to spurtfrom the dispenser
.
1
⁄2 gallons) to clear
o Use the
.
About the shelves and bins. ge.com
Not all features are on all models.
Rearranging the Shelves
Refrigerator Compartment
o remove:
T
Freezer Compartment
To remove:
Tilt the shelf up at the front.
ift the shelf up at the back
L and bring the shelf out.
Some models have wire shelves that can be adjusted in the same manner.
Lift and slide left.
Rotate up and out.
o replace:
T
To replace:
hile tilting the shelf up, insert
W the top hook at the back of the shelf in a slot on the track.
Lower the front of the shelf until the bottom of the shelf locks into place.
Holding the shelf diagonally, insert the left end of the shelf into the center of the shelf supports on the side wall.
Insert the right end of the shelf into the shelf supports on the side wall. Rest each end of the shelf on the bottom of the shelf supports.
Opening
Tab
Front bar
Slide-Out Spillproof Shelf (on some models)
The slide-out spillproof shelf allows you to reach items stored behind others. The special edges are designed to help prevent spills from dripping to lower shelves.
NOTE: The shelves are shipped with tape on the back. Remove this tape before attempting to remove the shelf.
To remove:
Remove all items from shelf.
Slide the shelf out until it stops.
Lift the front edge of the shelf until the tabs
are above the shelf frame.
Continue pulling the shelf forward until it
can be lifted out and removed.
To replace:
Place the rear of the shelf on the shelf frame
just behind the front bar.
Slide the shelf back until the tabs are above
the openings.
Lower the shelf so that the tabs go into the
openings; then slide the shelf all the way in.
Make sure that the shelf sits flat after reinstallation and doesn’t move freely from side to side.
Make sure you push the shelves all the way in before you close the door.
Adjustable Bins on the Door (on some models)
Adjustable bins can easily be carried from refrigerator to work area.
o remove:
T
Lift bin straight up; then pull out.
NOTE: Bins for the refrigerator and freezer doors are different sizes and are not interchangeable.
o replace or relocate:
T
Engage the bin in the molded supports of the door and push down. Bin will lock in place.
Non-Adjustable Shelves on the Door
Detachable shelves deepen and enclose fixed door shelves, providing more storage room and greater storage flexibility.
emove:
o r
T
Lift the shelf straight up; then pull out.
Freezer Tilt-Out Bin (on some models)
Push the button as you tilt out the bin. To remove: Hold the sides of the bin and
lift it straight up; then pull out.
To replace:
Engage the shelf extender in the molded supports on the door and push down. It will lock in place.
To replace: Engage the ends of the bin in the molded supports on the door and push down. It will lock in place.
NOTE: Do not overload the bin.
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions
5
About the crispers and pans.
Not all features are on all models.
Fruit and Vegetable Crispers
Excess water that may
ccumulate in the bottom
a
f the drawers or under the
o drawers should be wiped dry.
Snack Pan (on some models)
This pan can be moved to the most useful location for your family’s needs.
Adjustable Humidity Crisper (on some models)
Slide the control all the way to the HIGH setting to provide high humidity recommended for most vegetables.
Slide the control all the way to the provide lower humidity levels recommended for most fruits.
LOW setting to
Crisper Removal
Unload the bottom shelf before attempting to remove the storage drawers.
Operating Instructions Safety InstructionsInstallation Instructions
To Remove:
Lift the drawers up slightly while pulling them past the stop location.
If the door prevents you from taking out the drawers, first try to remove the door bins. If this does not offer enough clearance, the refrigerator will need to be rolled forward until the door opens enough to slide the drawers out. In some cases, when you roll the refrigerator out, you will need to move the refrigerator to the left or right as you roll it out.
To remove the glass cover:
Remove the glass, then the frame. When replacing the glass, push the front edge firmly into the frame.
Lift the back up off of its supports, slide it backward, tilt it and take it out.
Removing the glass cover
About the additional features.
Not all features are on all models.
ShelfSaver™Rack
This slide-out rack holds twelve cans of soda or two wine/water bottles (lengthwise). Can be removed for cleaning.
To remove the frame:
Lift the front of the frame, pull it forward, tilt it and take it out.
To remove, slide the rack out to the stop position, lift the rack up and past the stop, and lift out.
Consumer Support Troubleshooting Tips
6
About the automatic icemaker. ge.com
A newly-installed refrigerator may take 12–24 hours to begin making ice.
There are 2 types of icemakers:
ower
P Switch
Green Power Light
Power switch model
Feeler Arm in the ON (down) position
Feeler arm model
Feeler Arm
Icemaker
Feeler Arm in the STOP (up) position
Automatic Icemaker (
The icemaker will produce approximately
1
to 3
3 d
bs. of ice in a 24-hour period,
⁄2 l
epending on the freezer compartment
on some models)
temperature, room temperature, number of door openings and other use conditions.
If the refrigerator is operated before the water connection is made to the icemaker, move the feeler arm to the
STOP (up)
position. When the refrigerator has been connected
to the water supply, move the feeler arm to the ON (down) position.
The icemaker will fill with water when it cools to 15°F. A newly-installed refrigerator may take 12 to 24 hours to begin making ice cubes.
Once the icemaker starts to make ice, it may take up to 48 hours to fill the bin, depending on the temperature settings and number of door openings.
You will hear a buzzing sound each time the icemaker fills with water.
Throw away the first few batches of ice to allow the water line to clear.
Be sure nothing interferes with the sweep of the feeler arm.
When the bin fills to the level of the feeler
rm, the icemaker will stop producing ice.
a
t is normal for several cubes to be joined
I together.
If ice is not used frequently, old ice cubes will become cloudy, taste stale, shrink or fuse together.
On power switch models, the green power light will blink if ice cubes get stuck in the icemaker. To correct this, set the power switch to
O (off) and remove the cubes.
Set the power switch to I (on) to restart the icemaker. After the icemaker has been turned on again, there will be a delay of about 45 minutes before the icemaker resumes operation.
NOTE: In homes with lower-than-average water pressure, you may hear the icemaker cycle multiple times when making one batch of ice.
Icemaker accessory kit:
If your refrigerator did not already come equipped with an automatic icemaker, an icemaker accessory kit is available at extra cost.
Check the back of the refrigerator for the specific icemaker kit needed for your model.
Water Filter Accessory
The water filter is an option at extra cost and is available from your dealer. Specify WR97X0214. It has complete installation instructions and installs on 1/4″ O.D. copper water line or plastic tubing that is included in a GE SmartConnect
™
Refrigerator Tubing kit. When using the plastic tubing, an additional piece of plastic tubing (WX08X10002) must also be ordered since the plastic tubing should not be cut.
To Use the Dispenser (on some models)
The water dispenser is located on the left wall inside the refrigerator compartment.
o dispense water:
T
Hold the glass against the recess.
Push the water dispenser button.
Hold the glass underneath the
dispenser for 2–3 seconds after releasing the dispenser button. Water may continue to dispense after the button is released.
NOTE: The only GE approved plastic tubing is that supplied in GE SmartConnect™Refrigerator Tubing kits. Do not use any other plastic water supply line because the line is under pressure at all times. Certain types of plastic will crack or rupture with age and cause water damage to your home.
If no water is dispensed when the refrigerator is first installed, there may be air in the water line system.
ess the dispenser button for at least 2 minutes to
Pr
emove trapped air from the water line and to fill the
r water system. During this process, the dispenser noise may be loud as the air is purged from the water line system. T
o flush out impurities in the
water line, throw away the first 6 glassfuls of water.
NOTE: T
o avoid water deposits, the dispenser should be cleaned periodically by wiping with a clean cloth or sponge.
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions
7
Care and cleaning of the refrigerator.
Cleaning the Outside
The door handles and trim. Clean with
a cloth dampened with soapy water. Dry with a soft cloth.
eep the outside clean. Wipe with a clean
K
cloth lightly dampened with kitchen appliance wax or mild liquid dish detergent. Dry and polish with a clean, soft cloth.
The stainless steel panels and door handles
(on some models) can be cleaned with
a commercially available stainless steel cleaner. Do not use appliance wax or polish
n the stainless steel.
o
Do not wipe the refrigerator with a soiled dish cloth or wet towel. These may leave a residue that can erode the paint. Do not use scouring pads, powdered cleaners, bleach or cleaners containing bleach because these products can scratch and weaken the paint finish.
Cleaning the Inside
To help prevent odors, leave an open box of
baking soda in the fresh food and freezer compartments.
Unplug the refrigerator before cleaning. If this
Operating Instructions Safety InstructionsInstallation Instructions
is not practical, wring excess moisture out of sponge or cloth when cleaning around switches, lights or controls.
Use warm water and baking soda solution— about a tablespoon (15 ml) of baking soda to a quart (1 liter) of water. This both cleans and neutralizes odors. Thoroughly rinse and wipe dry.
Avoid cleaning cold glass shelves (on some models) with hot water because the extreme temperature difference may cause them to break. Handle glass shelves carefully. Bumping tempered glass can cause it to shatter.
Do not wash any plastic refrigerator parts in the dishwasher.
Do not clean with any products containing detergent, bleach or ammonia. They may damage the refrigerator.
Condenser
There is no need for routine condenser cleanings in normal home operating environments. However, in environments that may be particularly dusty or greasy condenser should be cleaned periodically for efficient refrigerator operation.
For models with a base grille, the grille must be removed in order to clean the condenser.
emove the base grille:
o r
T
Grasp it about 6″ from each end and pull its bottom edge toward you.
To replace the base grille:
Insert the tops of the metal clips into the oval vents, making sure one of the plastic tabs on the back of the grille goes into each
, the
of the oval vents. Then push the bottom of the grille forward until it snaps into place.
Cleaning the condenser:
Sweep away or vacuum up dust. For models with a base grille, reach the
condenser by inserting a brush or vacuum hose into the oval holes.
For models without a base grille, reach the condenser by inserting a brush or vacuum hose under the bottom of the refrigerator.
For best results, use a brush specially designed for this purpose. It is available at most appliance parts stores.
Moving the Refrigerator
Be careful when moving the refrigerator away from the wall. All types of floor coverings can be damaged, particularly cushioned coverings and those with embossed surfaces.
BEFORE moving the r
Consumer Support Troubleshooting Tips
be sure to adjust the leveling legs up. (See page 10 for details.)
efrigerator away from the wall,
8
Pull the refrigerator straight out and return it to position by pushing it straight in.
Moving the refrigerator in a side direction may result in damage to the floor covering or refrigerator.
When pushing the refrigerator back, make sure you don’t roll over the power cord or icemaker supply line (on some models).
Preparing for Vacation
ge.com
For long vacations or absences, remove food and unplug the refrigerator. Move the refrigerator control to the 0 (off) position and clean the interior with a baking soda solution of one tablespoon (15 ml) of baking soda to one quart (1 liter) of water. Leave the doors open.
Set the icemaker power switch to the O (off)
osition or move the feeler arm to the STOP
p
up) position (depending on model) and
(
hut off the water supply to the refrigerator.
s
If the temperature can drop below freezing, have a qualified servicer drain the water supply system (on some models) to prevent serious property damage due to flooding.
Preparing to Move
Secure all loose items such as grille, shelves and drawers by taping them securely in place to prevent damage.
Be sure the refrigerator stays in an upright position during moving.
Replacing the light bulbs.
Setting either or both controls to 0 (off) does not remove power to the light circuit.
Some models have only one light.
Light shield
Refrigerator Compartment—Upper Light
CAUTION:Light bulbs may be hot.
Unplug the refrigerator.
The bulbs are located at the top of the
compartment near the opening.
Replace with an appliance bulb of the same or lower wattage.
Plug the refrigerator back in.
Freezer Compartment Dome Light (on some models)
CAUTION:Light bulbs may be hot.
Unplug the refrigerator.
The bulb is located behind a light
shield at the back of the freezer compartment. To remove, squeeze the top and bottom of the shield and pull the shield off.
After replacing with an appliance bulb
of the same or lower wattage, replace
the shield.
Plug the refrigerator back in.
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions
9
10
Rollers allow you to move the refrigerator away from the wall for cleaning.
Leveling Legs near each front corner of the refrigerator, next to the rollers, should be adjusted if any of the following occurs:
• Refrigerator wobbles due to front roller not being firmly positioned on the floor.
• Door(s) do not close easily when opened to 45°.
NOTE:
• BEFORE moving the refrigerator away from the wall, be sure to turn the leveling legs counterclockwise so that the weight of the refrigerator is fully transferred to the front rollers.
• The refrigerator will not be level from front to back. It will have a slight backward tilt for proper door-closing.
To adjust the leveling legs,
turn the two front leveling legs clockwise to raise the front of the refrigerator and counterclockwise to lower it.
ROLLERS AND LEVELING LEGS
Clockwise to raise refrigerator
BEFORE YOU BEGIN
Read these instructions completely and carefully.
•
IMPORTANT – Save these
instructions for local inspector’s use.
•
IMPORTANT – Observe all
governing codes and ordinances.
• Note to Installer – Be sure to leave these
instructions with the Consumer.
• Note to Consumer – Keep these instructions
for future reference.
• Skill level – Installation of this appliance requires basic mechanical skills.
• Completion time – Refrigerator Installation
15 minutes Reversing the Door Swing
1 hour
• Proper installation is the responsibility of the installer.
• Product failure due to improper installation is not covered under the Warranty.
Allow the following clearances for ease of installation, proper air circulation and plumbing and electrical connections.
• Sides 1/8″ (3 mm)
• Top 1″ (25 mm)
• Back 1″ (25 mm)
If the refrigerator is to be installed next to a wall on the hinge side, allow 5/16″ (8 mm) door clearance.
CLEARANCES
If the refrigerator has an icemaker, it will have to be connected to a cold water line. A water supply kit (containing copper tubing, shutoff valve, fittings and instructions) is available at extra cost from your dealer, by visiting our Website at ge.com (in Canada at www.geappliances.ca) or from Parts and Accessories,
1.800.661.1616.
WATER SUPPLY TO THE ICEMAKER
(on some models)
Installation Instructions
Model 18
If you have questions, call 1.800.GE.CARES
or visit our Website at:
ge.com
In Canada, call 1.800.561.3344
or Visit our Website at:
www.geappliances.ca
• Do not install the refrigerator where the temperature will go below 60°F (16°C) because it will not run often enough to maintain proper temperatures.
• Do not install the refrigerator where the temperature will go above 100°F (37°C) because it will not perform properly.
• Install it on a floor strong enough to support it fully loaded.
REFRIGERATOR LOCATION
Installation Instructions
INSTALLING THE WATER LINE (ON SOME MODELS)
BEFORE YOU BEGIN
Recommended copper water supply kits are WX8X2, WX8X3
r WX8X4, depending on the amount of tubing you need.
o Approved plastic water supply lines are GE SmartConnect Refrigerator Tubing (WX08X10006, WX08X10015 and WX08X10025).
When connecting your refrigerator to a GE Reverse Osmosis Water System, the only approved installation is with a GE RVKit. For other reverse osmosis water systems, follow the manufacturer’s recommendations.
This water line installation is not warranted by the refrigerator or icemaker manufacturer. Follow these instructions carefully to minimize the risk of expensive water damage.
Water hammer (water banging in the pipes) in house plumbing can cause damage to refrigerator parts and lead to water leakage or flooding. Call a qualified plumber to correct water hammer before installing the water supply line to the refrigerator.
To prevent burns and product damage, do not hook up the water line to the hot water line.
If you use your refrigerator before connecting the water line, make sure the feeler arm is in the
Do not install the icemaker tubing in areas where temperatures fall below freezing.
When using any electrical device (such as a power drill) during installation, be sure the device is double insulated or grounded in a manner to prevent the hazard of electric shock, or is battery powered.
All installations must be in accordance with local plumbing code requirements.
STOP (up) position.
™
WHAT YOU WILL NEED (CONT.)
• A GE water supply kit (containing tubing, shutoff
valve and fittings listed below) is available at extra cost from your dealer or from Parts and Accessories,
1.800.661.1616.
• A cold water supply. The water pressure must be
between 20 and 120 p.s.i. (1.4–8.1 bar).
• Power drill.
• 1/2″ or adjustable wrench.
• Straight and Phillips blade screwdriver.
• Two 1/4″ outer diameter compression nuts and
2 ferrules (sleeves)
to the shutoff valve and the refrigerator water valve.
OR
• If you are using a GE SmartConnect™Refrigerator Tubing kit, the necessary fittings are preassembled to the tubing.
—to connect the copper tubing
WHAT YOU WILL NEED
• Copper or GE SmartConnect™Refrigerator Tubing kit,
1/4″ outer diameter to connect the refrigerator to the water supply. If using copper, be sure both ends of the tubing are cut square.
To determine how much tubing you need: Measure the distance from the water valve on the back of the refrigerator to the water supply pipe. Then add 8 tubing (about 8′ [2.4 m] coiled into 3 turns of about 10″ [25 cm] diameter) to allow the refrigerator to move out from the wall after installation.
GE SmartConnect™Refrigerator Tubing Kits are available in the following lengths:
6′ (1.8 m) – WX08X10006 15′ (4.6 m) – WX08X10015 25′ (7.6 m) – WX08X10025
Be sure that the kit you select allows at least 8′ (2.4 m) as described above.
NOTE: The only GE approved plastic tubing is that supplied in GE SmartConnect™Refrigerator T other plastic water supply line because the line is under pr at all times. Certain types of plastic will crack or rupture with age and cause water damage to your home.
′ (2.4 m). Be sure there is sufficient extra
ubing kits. Do not use any
essur
e
11
• If your existing copper water line has a flared fitting at the end, you will need an adapter (available at plumbing supply stores) to connect the water line to the refrigerator with a
tube cutter and then use a compression fitting.
Do not cut formed end from GE SmartConnect Refrigerator tubing.
• Shutoff valve to connect to the cold water line. The shutoff valve should have a water inlet with a minimum inside diameter of 5/32 connection to the shutoff valves are included in many water supply kits. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes.
OR you can cut off the flared fitting
™
″ at the point of
COLD WATER LINE. Saddle-type
Installation Instructions
INSTALLING THE WATER LINE (CONT.)
nstall the shutoff valve on the nearest frequently used
I drinking water line.
1
SHUT OFF THE MAIN WATER SUPPLY AND UNPLUG REFRIGERATOR
Turn on the nearest faucet counterclockwise long enough to clear the line of water.
2
DRILL THE HOLE FOR THE VALVE
Choose a location for the valve that is easily accessible. It is best to connect into the side of a vertical water pipe. When it is necessary to connect into a horizontal water pipe, make the connection to the top or side, rather than at the bottom, to avoid drawing off any sediment from the water pipe.
Drill a 1/4 self-piercing valve), using a sharp bit. Remove any burrs resulting from drilling the hole in the pipe.
Take care not to allow water to drain into the drill.
Failure to drill a 1/4″ hole may result in reduced ice production or smaller cubes.
″ hole in the water pipe (even if using a
4
ROUTE THE TUBING
oute the tubing between the cold water line and
R
he refrigerator.
t
Route the tubing through a hole drilled in the wall or floor (behind the refrigerator or adjacent base cabinet) as close to the wall as possible.
NOTE: Be sure there is sufficient extra tubing to allow the refrigerator to move out from the wall after installation
5
CONNECT THE TUBING TO THE VALVE
Place the compression nut and ferrule (sleeve) for copper tubing onto the end of the tubing and connect it to the shutoff valve.
Make sure the tubing is fully inserted into the valve. Tighten the compression nut securely.
For plastic tubing from a GE SmartConnect Refrigerator Tubing kit, insert the molded end of the tubing into the shutoff valve and tighten compression nut until it is hand-tight; then tighten one additional turn with a wrench. Overtightening may cause leaks.
Saddle-Type Shutoff Valve
.
™
Compression Nut
SmartConnect Tubing
™
3
FASTEN THE SHUTOFF VALVE
Fasten the shutoff valve to the cold water pipe with the pipe clamp.
ighten the clamp screws until the sealing washer
T begins to swell.
NOTE: Do not overtighten or you may crush the tubing.
Pipe Clamp
Clamp Scr
Saddle-Type Shutoff Valve
NOTE: Commonwealth of Massachusetts Plumbing Codes 248CMR shall be adhered to. Saddle valves are illegal and use is not permitted in Massachusetts. Consult with your licensed plumber.
ew
Washer
Inlet End
er
V
ater Pipe
W
tical Cold
12
Packing Nut
alve
Outlet V
NOTE: Commonwealth of Massachusetts Plumbing Codes 248CMR shall be adhered to. Saddle valves are illegal and use is not permitted in Massachusetts. Consult with your licensed plumber.
6
FLUSH OUT THE TUBING
Turn the main water supply on counterclockwise and flush out the tubing until the water is clear.
Shut the water off at the water valve after about one quart (1 liter) of water has been flushed through the tubing.
Ferrule (sleeve)
Installation Instructions
7
CONNECT THE TUBING TO THE REFRIGERATOR
NOTES:
efore making the connection to the refrigerator,
• B e sure the refrigerator power cord is not
b plugged into the wall outlet.
• We recommend installing a water filter if your
water supply has sand or particles that could clog the screen of the refrigerator’s water valve. Install it in the water line near the refrigerator. If using GE SmartConnect will need an additional tube (WX08X10002) to connect the filter. Do not cut plastic tube to install filter.
Remove the screws holding the right side of the access cover. Fold back the cover.
Remove the plastic flexible cap from the water valve (refrigerator connection).
Place the compression nut and
ferrule (sleeve) onto the end of the tubing as shown. On GE SmartConnect Tubing kit, the nuts are already assembled to the tubing.
™
Refrigerator Tubing kit, you
™
Refrigerator
7
CONNECT THE TUBING TO THE REFRIGERATOR (CONT.)
One of the illustrations below will look like the
onnection on your refrigerator.
c
Icemaker Models without Water Dispenser
1/4″ Tubing
Tubing Clamp
1/4″ Compression Nut
Ferrule (sleeve)
SmartConnect Tubing
Water Dispenser Models
Tubing Clamp
1/4″ Compression Nut
Ferrule (sleeve)
™
Refrigerator Connection
1/4″ Tubing
Insert the end of the tubing into the water valve connection as far as possible. While holding the tubing, tighten the fitting.
For plastic tubing from a GE SmartConnect Refrigerator Tubing kit, insert the molded end of the tubing into the water valve connection and tighten compression nut until it is hand-tight; then tighten one additional turn with a wrench. Overtightening may cause leaks.
Fasten the tubing into the clamp provided to hold
it in a vertical position. You may need to pry open the clamp.
™
Refrigerator Connection
8
TURN THE WATER ON AT THE
SmartConnect™Tubing
SHUTOFF VALVE
Tighten any connections that leak.
Reattach the access cover.
13
Installation Instructions
INSTALLING THE WATER LINE (CONT.)
9
PLUG IN THE REFRIGERATOR
Arrange the coil of tubing so that it does not vibrate
gainst the back of the refrigerator or against the
a
all. Push the refrigerator back to the wall.
w
START THE ICEMAKER
On power switch models, set the icemaker power switch to the l (on) position. On feeler arm models, move the feeler arm to the ON (down) position. The icemaker will not begin to operate until it reaches its operating temperature of 15°F (–9°C) or below. It will then begin operation automatically.
NOTE: In lower water pressure conditions, the water valve may turn on up to 3 times to deliver enough water to the icemaker.
Feeler Arm in
ON (down) position
the
Feeler Arm in the STOP (up) position

REVERSING THE DOOR SWING

IMPORTANT NOTES
When reversing the door swing:
• Read the instructions all the way through before starting.
• Handle parts carefully to avoid scratching paint.
• Set screws down by their related parts to avoid using
them in the wrong places.
• Provide a non-scratching work surface for the doors.
IMPORT
cabinet until door These instructions are for changing the hinges from
the right side to the left side—if you ever want to change the hinges back to the right side, follow these same instructions and reverse all references to left and right.
Unplug the refrigerator from its electrical outlet.
Empty all door shelves, including the dairy compartment.
ANT:
Once you begin, do not move the
-swing reversal is completed.
TOOLS YOU WILL NEED
Phillips screwdriver
Masking tape
T20 or T25 Torx driver, whichever your model requires
®
3/8″ Head socket driver
(a 6-point socket is
ecommended)
r
Putty knife or
thin-blade screwdriver
14
Installation Instructions
1
REMOVE FREEZER DOOR
Tape the door shut with masking tape.
Top Hinge
Remove the hinge cover on top of the freezer door (on some models).
®
Remove the two Torx straight up to free the hinge pin from the socket in the top of the door.
Remove the tape and tilt the door away from the cabinet. Lift it off the center hinge pin.
Set the door on a non-scratching surface with the inside up.
2
REMOVE REFRIGERATOR DOOR
screws, then lift the hinge
3
TRANSFER TOP HINGE TO THE LEFT
Interchange hinge and screws at top right with screws at the top left of cabinet.
Do not tighten screws on hinge side at this time.
4
TRANSFER BOTTOM HINGE BRACKET TO THE LEFT
For models with a base grille, remove it by grasping it about 6″ from each end and pulling its bottom edge toward you.
Using a Torx and plastic washer from the right side to the left side.
NOTE: If the washer is not on the hinge bracket, check to see if it is stuck to the bottom of the door.
®
driver, move the bottom hinge bracket
Tape the door shut with masking tape.
Remove the center hinge pin with a 3/8 and ratchet.
Plastic Washer
Hinge Pin
Center Hinge Bracket
Fresh Food Door
Remove the tape and tilt the door away from the cabinet. Remove and save the washer on the hinge pin. Lift the door straight up to free its bottom socket from the pin in the bottom hinge bracket.
Set the door on a non-scratching surface with the inside up.
″ socket
CAUTION: Do not let door drop to the floor To do so could damage the door stop.
Plastic Washer
Hinge Bracket
For models with a base grille, before replacing the base grille, remove the grille cap by removing the screw. Screw the cap to the opposite side.
Replace the base grille by inserting the tops of the metal clips into the oval vents, making sure one of the
.
plastic tabs on the back of the grille goes into each of the oven vents. Then push the bottom of the grille forward until it snaps into place.
15
Installation Instructions
REVERSING THE DOOR SWING (CONT.)
5
TRANSFER CENTER HINGE BRACKET TO THE LEFT
emove the center hinge bracket by removing the
R
hree Torx
t NOTE: Keep these screws with the hinge bracket.
They are long screws and will be used when installing the hinge on the other side.
On some models, you will need to remove the color­matched caps from the screw heads before you can remove the screws. Use the edge of a thin flat blade to gently pry the caps off the screw heads. (A putty knife works well for this.) Cover the blade with tape to prevent scratching the paint.
Remove the three Torx side of the cabinet. Screw them into the holes on the right side.
Place the center hinge bracket over the holes at the center left side of the cabinet. Insert and tighten the three long screws.
Replace the caps by snapping them over the screws with your finger.
®
crews.
s
®
screws from the center left
Screw Cap
7
TRANSFER REFRIGERATOR DOOR HANDLE TO THE RIGHT
lastic handle:
P
Remove the plug button by carefully prying under the edge with a putty knife.
Remove the exposed screw holding the handle. Remove the two screws holding the handle to the top of the door.
Stainless steel handle (on some models):
Remove the two screws holding the handle to the top of the door. Loosen the set screw with the
″ Allen wrench
3/32 (supplied) and remove the handle. Remove the handle fastener with the 3/16″ Allen wrench (supplied).
Transfer the fastener to the right side and move the plug button to the left side of the refrigerator door.
3
2
Fastener
2
Handle Plug
1
1
Handle Plug
3
Plug Button
6
TRANSFER DOOR STOPS
On each door right to the left.
Move any screws from the left to the right.
Left Side
, move the metal door stop from the
Door Stop
Door Stop
Right Side
16
After removing the handle: Move the small
plug buttons from the top right side of the door top and insert them into the holes on the opposite side.
Move the large plug button from the left edge of the door and insert it into the hole on the opposite side.
Small Plug Buttons
Plug Button
Installation Instructions
7
TRANSFER REFRIGERATOR DOOR HANDLE TO THE RIGHT (CONT.)
ransfer the door plug
T
utton to the opposite
b side.
Reinstalling the handle:
Attach the handle to the right side of the door.
Plastic handle:
Line up the handle with the screw holes in the top of the door and tighten the screws. Install the screw into the bottom of the handle.
Reinstall the handle plug.
Stainless steel handle (on some models):
Attach the handle to the fastener and tighten with the 3/32″ Allen wrench (supplied). Line up the handle with the screw holes in the top of the door and tighten the screws.
Button
4
Handle
Plug
2
8
TRANSFER FREEZER DOOR HANDLE TO THE RIGHT
lastic handle:
P
Remove the screws
1
2
3
1
holding the handle to the top and bottom of the door. Remove handle. Move the plug button on the right side of the door to the handle screw hole on the left side.
Stainless steel handle (on some models):
Remove the two screws holding the handle to the bottom of the door. Loosen the set screw with the 3/32″ Allen wrench (supplied) and remove the handle.
Remove the handle fastener with the 3/16″ Allen wrench (supplied). Transfer the fastener to the right side and move the GE badge to the left side of the freezer door. Remove the paper covering on the adhesive backing prior to attaching the badge to the door.
Reattach the handle on the opposite side using the holes closest to the edge of the door.
1
2
2
Fastener
3
Plug
Button
3
1
17
Plastic handle:
Line up the handle with the screw hole in the top of the door and tighten screw. Install the two screws into the bottom of the handle.
Move the plug button on the right side of the door to the handle screw hole on
Plug
Button
3
1
2
Installation Instructions
REVERSING THE DOOR SWING (CONT.)
8
TRANSFER FREEZER DOOR HANDLE TO THE RIGHT (CONT.)
Stainless steel handle (on some models):
Attach the handle to the fastener and tighten with the 3/32″ Allen wrench (supplied).
Line up the handle with the screw holes in the bottom of the door and tighten the screws.
9
RE-HANG THE REFRIGERATOR DOOR
Lower the refrigerator door onto the bottom hinge pin.
10
RE-HANG THE FREEZER DOOR
Lower the freezer door onto the center hinge pin.
1
2
Be sure the washer is in place.
Center Hinge Pin
Plastic Washer
Lift the top hinge so the pin fits into the door socket. Support the door on the handle side and make sure
the door is straight and the gap between the doors is even across the front. While holding the door in place, tighten the top hinge screws.
Plastic Washer
Straighten the door and line it up with the center hinge bracket.
Reinstall the center hinge pin with a 3/8″ socket. Turn it until it extends through the hinge bracket and into the door
Plastic Washer
Center Hinge Bracket
.
Hinge Pin
Refrigerator Door
18
Normal operating sounds. ge.com
Newer refrigerators sound different from older refrigerators. Modern refrigerators have more features and use newer technology.
Do you hear what I hear? These sounds are normal.
HUMMM...
WHOOSH...
■
The new high efficiency compressor may run faster and longer than your old refrigerator and you may hear a high-pitched hum or pulsating sound while it is operating.
■
You may hear a whooshing sound when the doors close. This is due to pressure equalizing within the refrigerator.
■
You may hear the fans spinning at high speeds. This happens when the refrigerator is first plugged in, when the doors are opened frequently or when a large amount of food is added to the refrigerator or freezer compartments. The fans are helping to maintain the correct temperatures.
CLICKS, POPS,
CRACKS and CHIRPS
■
You may hear cracking or popping sounds when the refrigerator is first plugged in. This happens as the refrigerator cools to the correct temperature.
■
The compressor may cause a clicking or chirping sound when attempting to restart (this could take up to 5 minutes).
■
Expansion and contraction of cooling coils during and after defrost can cause a cracking or popping sound.
■
On models with an icemaker, after an icemaking cycle, you may hear the ice cubes dropping into the ice bucket.
■
On models with a dispenser, during water dispense, you may hear the water lines move at initial dispense and after dispenser button is released.
Before you call for service…
Troubleshooting Tips Save time and money! Review the charts on the following pages first and you may not need to call for ser
vice.
WATER SOUNDS
■
The flow of refrigerant through the freezer cooling coils may make a gurgling noise like boiling water.
■
Water dropping on the defrost heater can cause a sizzling, popping or buzzing sound during the defrost cycle.
■
A water dripping noise may occur during the defrost cycle as ice melts from the evaporator and flows into the drain pan.
■
Closing the door may cause a gurgling sound due to pressure equalization.
For additional information on normal icemaker operating sounds, see the
About the automatic icemaker section.
Problem Possible Causes What To Do
Freezer door pops open This is normal if, after • This indicates that there is a good seal on the freezer when refrigerator door popping open, the freezer door. If the freezer door does not automatically close after is closed door closed on its own. popping open, the rollers need adjusting. See Rollers and
Leveling Legs.
Door does not close Leveling legs need adjusting. • See Rollers and Leveling Legs. by itself
Refrigerator does Refrigerator in defrost cycle. • Wait about 40 minutes for defrost cycle to end. not operate
Vibration or rattling Refrigerator is not resting • Adjust leveling legs (See Rollers and Leveling Legs). (slight vibration on all four r is normal)
Refrigerator contr
f)
0 (of
position. temperature setting. Refrigerator is unplugged. • Push the plug completely into the outlet. The fuse is blown/cir
eaker is tripped.
br
ollers.
ol in
cuit
• Move the refrigerator and freezer control to a
• Replace fuse or reset the breaker
.
19

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

Consumer Support
Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions
Before you call for service…
Problem Possible Causes What To Do
Motor operates for
Normal when refrigerator • Wait 24 hours for the refrigerator to completely
long periods or cycles
is first plugged in. cool down.
on and off frequently
Often occurs when large • This is normal.
(Modern refrigerators
amounts of food are
with more storage
placed in refrigerator.
space and a larger
Door left open. • Check to see if package is holding door open.
freezer require more
Hot weather or frequent • This is normal.
operating time. They
door openings.
start and stop often
Temperature controls set • See
About the controls.
to maintain even
at the coldest setting.
temperatures.)
Refrigerator or freezer
Temperature control not set • See
About the controls.
compartment too warm
cold enough. Warm weather or frequent • Set the temperature control one step colder.
door openings. See
About the controls.
Door left open. • Check to see if package is holding door open. Freezer door popped open. • See the problem
Freezer door pops open when
refrigerator door is closed.
Frost or ice crystals
Door left open. • Check to see if package is holding door open.
on frozen food
Too frequent or too long
(frost within package
door openings.
is normal)
Food blocking freezer air vents. • Move items away from the back wall of the freezer.
Frequent “buzzing”
Icemaker power switch is in • On power switch models, set the power switch to the
O (off)
sound
the
I (on)
position, but the position. On feeler arm models, move the feeler arm to the
water supply to the refrigerator
STOP
(up) position. Keeping the power switch in the
I (on)
has not been connected. position or the feeler arm in the ON(down) position will
damage the water valve.
Small or hollow cubes
Water filter clogged. • Replace filter cartridge with new cartridge or with plug.
Automatic icemaker
Icemaker power switch is not on. • On power switch models, set the power switch to the
does not work I (on)
position. On feeler arm models, move the feeler
(on some models)
arm to the ON(down) position.
Water supply turned off or •See
Installing the water line.
not connected. Freezer compartment too warm. • Wait 24 hours for the refrigerator to completely cool down. Piled up cubes in the storage • Level cubes by hand.
bin cause the icemaker to shut off.
Ice cubes stuck in icemaker. • Turn off the icemaker, remove cubes and turn the (Green power light on icemaker back on. icemaker blinking.)
Ice cubes have
Ice storage bin needs cleaning. •Empty and wash bin. Discard old cubes.
odor/taste
Food transmitting odor/taste • Wrap foods well. to ice cubes.
Interior of refrigerator • See
Care and cleaning.
needs cleaning.
Slow ice cube freezing
Door left open. • Check to see if package is holding door open. Temperature control not set •See
About the controls.
cold enough.
• A newly installed refrigerator may take 12–24 hours
to begin making ice cubes.
Moisture forms on
Not unusual during • Wipe surface dry; then adjust the fresh food control
cabinet surface
periods of high humidity. setting one number higher and check again in 24 hours.
between the doors Refrigerator has odor
Foods transmitting • Foods with strong odors should be tightly wrapped. odor to refrigerator.
• Keep an open box of baking soda in the refrigerator;
replace every three months.
Interior needs cleaning. • See
Care and cleaning.
Refrigerator compartment
No power at outlet. • Replace fuse or reset the breaker.
light does not work
Light bulb burned out or loose. • See
Replacing the light bulbs.
20
ge.com
P
roblem Possible Causes What To Do
Moisture collects inside Too frequent or too
in humid weather, air
( carries moisture into refrigerator when doors are opened)
Hot air from bottom Normal air flow cooling motor. In the refrigeration process, of refrigerator it is normal that heat be expelled in the area under the refrigerator.
Food freezing in Food too close to the air vent • Move the food away from the air vent (near the the refrigerator at the back of the refrigerator. controls).
Orange glow Defrost heater is on. • This is normal. in the freezer
Door bins do not fit in the door a different size than the
Freezer light does Some models do not have a • Check for a semi-clear dome light shield in the freezer ceiling. not work freezer light. If the dome is opaque white, the model does not have a freezer
Controls do not light up Some models do not have • If you can read white numbers on the control setting,
Ice bucket does not fit The freezer shelf is in the • Place the shelf in the lower position. See Rearranging under the icemaker top position. the shelves.
Water has poor Water dispenser has not been • Dispense water until all water in system is replenished. taste/odor used for a long time.
Water in first glass Normal when refrigerator • Wait 24 hours for the refrigerator to completely cool down. is warm is first installed.
Water dispenser Water supply line turned off • See Installing the water line. does not work or not connected.
Water spurting from Newly-installed filter cartridge. •Run water from the dispenser for 3 minutes dispenser (about 11⁄2 gallons).
ater is not dispensed
W but icemaker is working because the contr
No water or ice cube Supply line or shutof production is clogged.
Water is leaking from Glass not being held under • Hold the glass underneath the dispenser for 2–3 seconds dispenser the dispenser long enough after releasing the dispenser button. Water may continue
ong door openings.
l Open containers of water or • Cover or seal open containers. During a defrost cycle,
warm food in the refrigerator. moisture will be removed from the refrigerator, but may
return with long or frequent door openings.
Some floor coverings will discolor at these normal and safe temperatures.
Refrigerator control is set • Move the refrigerator control to a warmer too cold. temperature setting one increment at a time.
The freezer door bins are • Try to install the bins in both doors.
refrigerator door bins.
light. Check for a door activated light switch on the right side of the freezer. If there is only a cap in place of a switch, the model does not have a freezer light.
Light bulb burned out • See Replacing the light bulbs. or loose.
lighted controls. the model does not have lighted controls. Refrigerator light bulb burned • See Replacing the light bulbs.
out or loose.
Water dispenser has not been • Dispense water until all water is system is replenished. used for a long time.
Water system has been drained. • Allow several hours for replenished supply to chill.
Water filter clogged. • Replace filter cartridge or remove filter and install plug. Air may be trapped in • Press the dispenser arm for at least 2 minutes.
the water system.
ols ar
f valve
ozen
e
• Set the refrigerator control to a warmer setting and
wait 24 hours. If water does not dispense after 24 hours,
• Call a plumber
• Replace filter cartridge or remove filter and install plug.
should be positioned vertically.
• Dispense water for at least 2 minutes to remove air
.
voir is fr
eser
ater in r
W
set too cold. call for service.
W
ater filter clogged.
Filter cartridge not • Remove and reinstall filter cartridge, being certain that properly installed. it locks into place. The blade on the end of the cartridge
after button is released. to dispense after the button is released. Air may be pr
water line system, causing from system. water to drip after being dispensed.
esent in the
21
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions
Consumer Product Ownership Registration
D
ear Customer:
T
hank you for purchasing our product and thank you for placing your confidence in us.
We are proud to have you as a customer!
Follow these three steps to protect your new appliance investment:
1
Complete and mail your Consumer Product Ownership Registration today.
Have the peace of
ind of knowing we
m
an contact you in
c
he unlikely event of
t a safety modification.
23
After mailing the
egistration below,
r
tore this document
s
n a safe place. It
i contains information you will need should you require service. Our service number is 800 GE CARES (800.432.2737).
Model Number Serial Number
Important: If you did not get a registration card with your
product, detach and return the form on the next page to ensure that your product is registered, or register online at ge.com. The top card is for products installed in the U.S. The bottom card is for products installed in Canada.
Read your Owner’s
anual carefully.
M
t will help you
I
perate your new
o appliance properly.
Service Protection Plus
GE, a name recognized worldwide for quality and dependability Service Protection Plus —comprehensive protection on all your appliances—
No Matter What Brand!
™
, offers you
We’ll Cover
Benefits Include:
• Limit unexpected r
• One toll-free number to call
• Quality service performed by GE authorized technicians
vice coverage for most major brands
• Ser
• Convenient hours designed to meet your busy schedule
ou will be completely satisfied with our ser
Y on the remaining value of your contract. No questions asked.
Protect your refrigerator, dishwasher Plus there’s no extra charge for emergency service and low monthly financing is available. Even icemaker coverage and food spoilage protection is offered. You can rest easy, knowing that all your valuable household products are protected against expensive repairs.
Place your confidence in GE and call us in the U.S. toll-free at for more information.
epair costs
vice protection or you may request your money back
, washer and dr
yer, range, TV, VCR and much more—
Most Any Appliance. Anywhere. Anytime.*
s that simple.
It’
most any brand!
800.626.2224
22
*Most all brands covered, up to 20 years old, in the continental U.S.
OWNERSHIP REGISTRATION P.O. BOX 1780 MISSISSAUGA, ONTARIO L4Y 4G1
(FOR CANADIAN CONSUMERS ONLY)
Please place in envelope and mail to: Veuillez mettre dans une enveloppe et envoyez à :
For refrigerators installed in the U.S.
Please place in envelope and mail to:
General Electric Company
Warranty Registration Department P.O. Box 32150 Louisville, KY 40232-2150
✁
Cut here
For refrigerators installed in Canada
✁
Cut here
23
For refrigerators installed in the U.S.
GE Consumer & Industrial
Appliances General Electric Company Louisville, KY 40225 ge.com
Consumer Product Ownership Registration
Model Number Serial Number
Important
Mail Today!
■■
irst
F
Name
Street
Address
r.
M
■■
s.
M
■■
rs.
M
■■
iss
M
Last
Name
✁
Cut here
Apt. #
City
D
ate Placed
In Use
Month
Day
For refrigerators installed in Canada
E-mail Address*
State
Phone
Year
* Please provide your e-mail address to receive, via e-mail, discounts, special offers and other
important communications from GE Appliances (GEA).
■■
Check here if you do not want to receive communications from GEA’s carefully selected partners. FAILURE TO COMPLETE AND RETURN THIS CARD DOES NOT DIMINISH YOUR WARRANTY RIGHTS. For information about GEA’s privacy and data usage policy, go to ge.com and click on “Privacy Policy” or call 800.626.2224.
Number
_
Zip
ode
C
_
Cut here
✁
24
Loading...
+ 56 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use