GE 0150-0193C User Manual

Download

Caalliibbuurr

DVV

Digital Video Multiplexer Recorder

TTrriipplleex

x©

User Manual

WARNING!

To prevent fire and electric shock, do not expose this product to rain or moisture.

The lightning flash with the arrowhead symbol,

within an equilateral triangle, is intended to alert

the user to the presence of uninsulated

"dangerous voltage" within the products enclosure

that maybe of sufficient magnitude to constitute a

risk of electric shock to persons.

CAUTION!

To prevent electric shock, do not remove cover.

No user serviceable components inside. Refer

servicing to qualified service personnel.

The exclamation point, within an equilateral

triangle, is intended to alert the user to the

presence of important operating and maintenance

(servicing) instructions in the literature

accompanying the product.

CAUTION! Lithium Battery

Danger of explosion if battery is

incorrectly replaced. Replace only

with the same or equivalent type

This equipment generates, uses and can radiate radio frequency energy, and if not installed and used

in accordance with the instructions in this manual, may cause interference to radio communications. It

has been tested and found to comply with the limits for a Class A computing device pursuant to subpart

J of part 15 of FCC rules which are designed to provide reasonable protection against such

interference when operated in a commercial environment. This equipment has also been tested and

found to comply with the requirements for a CE Class A device and TUV safety standards.

recommended by the

manufacturer.

Electrostatic-Sensitive Device!

Use proper CMOS and MOSFET handing precautions, including approved

grounded wrists straps, etc., to avoid damage to this unit or its internal

components, from electric discharge.

WARNING!

This product contains a recyclable lithium battery.

It may be illegal to dispose of this battery

improperly under local, state, or federal laws.

Check with your local waste management officials

for disposal and recycling options.

CAUTION!

ATTENTION

Operation of this equipment in a residential area may cause interference, in which case the user is

required to take all measures that are necessary, at the user's expense, to correct the interference.

0150-0193C 2 Calibur DVMRe Triplex

IMPORTANT INFORMATION

Software and/or firmware is furnished to the purchaser under a license for use on a single system. Software and/or firmware included with this equipment are the sole proprietary property of, confidential to, and copyrighted by GE-Interlogix Kalatel Division, Corvallis, Oregon, USA. The software/firmware are not to be copied or disclosed in any manner without the express written consent of GE-Interlogix.

All information and specifications furnished by GE-Interlogix are believed to be accurate and reliable. No responsibility is assumed by GE-Interlogix for neither its use nor any infringements of rights of third parties that may result from its use. No license is granted by implication or otherwise under any patent or patent rights of GE-Interlogix.

The CALIBUR™ brand name and product model numbers are the property of GE-Interlogix. COPYRIGHT, 2002: The contents of this manual may not be copied or reproduced in any manner or

form without the prior written consent of GE-Interlogix.

0150-0193C 3 Calibur DVMRe Triplex

Contents

1 DVMR

1.1 Products Featured In This Manual...................................................................................6

1.2 Product Description ..........................................................................................................6

1.3 Passwords......................................................................................................................... 7

1.4 Unpacking.........................................................................................................................8

1.5 Installation Environment ..................................................................................................8

1.6 Associated Equipment...................................................................................................... 8

1.7 The Back Panel .................................................................................................................9

1.8 Power-Up.........................................................................................................................14

1.9 Minimum Recommended Menu Setup...........................................................................14

2 DMVR

2.1 Principal Operating Modes.............................................................................................16

2.2 The Front Panel...............................................................................................................16

2.3 Live Viewing....................................................................................................................17

2.4 Playback..........................................................................................................................18

2.5 Recording........................................................................................................................20

2.6 Display Options............................................................................................................... 21

2.7 Active Cameos................................................................................................................21

2.8 Sequencing .....................................................................................................................22

2.9 On-screen Indicators......................................................................................................23

2.10 Triplex Mode....................................................................................................................25

Triplex Overview.......................................................................................6

Triplex Basic Operations .......................................................................16

3 Menu System Overview.......................................................................................27

3.1 Menu Notation In This Manual........................................................................................27

3.2 Accessing The Menu System.........................................................................................27

3.3 Available Menus..............................................................................................................27

3.4 Menus In This Manual.....................................................................................................28

3.5 Navigating The Menu System.........................................................................................28

3.6 Menu Shortcuts...............................................................................................................28

3.7 The Main Menu................................................................................................................29

3.8 Time/Date ........................................................................................................................29

3.9 Sequencing .....................................................................................................................31

3.10 Record ............................................................................................................................31

3.11 Alarms ............................................................................................................................37

3.12 Macro..............................................................................................................................42

3.13 Motion Detection............................................................................................................44

3.14 Camera Setup.................................................................................................................47

3.15 Archive Setup.................................................................................................................50

3.16 Audio Setup....................................................................................................................51

3.17 Communications............................................................................................................51

0150-0193C 4 Calibur DVMRe Triplex

3.18 Front Panel Lock............................................................................................................53

3.19 Factory Settings.............................................................................................................53

3.20 Passwords......................................................................................................................54

3.21 The QuickInstall Menu ...................................................................................................54

3.22 The Operator Menu ........................................................................................................55

3.23 The SystemView Menu...................................................................................................56

4 Alarms ..................................................................................................................59

4.1 Alarm Input......................................................................................................................59

4.2 Alarm Output...................................................................................................................59

4.3 Alarm Acknowledge........................................................................................................59

4.4 On-screen Displays During Alarms................................................................................59

4.5 Alarm Operations During Playback................................................................................60

4.6 Alarm History Box...........................................................................................................61

4.7 Searching For Recorded Alarms....................................................................................61

5 Searching .............................................................................................................62

5.1 Disk Analysis Screen......................................................................................................63

5.2 Motion Search.................................................................................................................63

5.3 Search Filters..................................................................................................................65

5.4 Search Results ................................................................................................................65

6 Technical Specifications.....................................................................................67

7 RS232 Event Generation/Text Insertion Protocol.............................................69

7.1 Message Structure..........................................................................................................69

7.2 Message Type.................................................................................................................69

7.3 Event Field ......................................................................................................................69

8 RS232 Remote Control Protocol........................................................................71

8.1 Front Panel Button Emulation........................................................................................71

8.2 Configuration and Status ...............................................................................................72

9 Macro Tables........................................................................................................73

9.1 Macro Functions Table...................................................................................................73

9.2 Scheduled Macro Table..................................................................................................74

10 Warranty and Service..........................................................................................75

10.1 Factory Service ...............................................................................................................75

10.2 Warranty and Return Information..................................................................................76

0150-0193C 5 Calibur DVMRe Triplex

1 DVMR

Triplex Overview

1.1 Products Featured In This Manual

DVMRe -4CT: Digital Video Multiplexer Recorder, Four-Channel, Color, Triplex. DVMRe -10CT: Digital Video Multiplexer Recorder, Ten-Channel, Color, Triplex. DVMRe -16CT: Digital Video Multiplexer Recorder, Sixteen-Channel, Color, Triplex.

Key To Model Numbers

1. DVMRe: Digital Video Multiplexer Recorder, Ethernet capable.

DVMRe 16 C T

2. 4, 10, or 16: Maximum number of camera inputs.

3. C: Color.

4. T: Triplex.

1 2 3 4

1.2 Product Description

The DVMRe Triplex is a video multiplexer capable of recording from multiple cameras to an internal hard drive while simultaneously providing playback. Unlike outdated time-lapse VCRs, the DVMRe Triplex records high-resolution pictures. Digital recording improves playback quality over VCRs, and eliminates the hassle of cleaning heads, changing tapes or servicing motors. The unit can also be programmed to record continuously by overwriting the oldest recorded data. Depending on the setup, the DVMRe Triplex can store from a few hours to more than 3 years of color images.

Programmable search features eliminate time consuming Fast Forwarding or Rewinding of tapes, searching for critical data. Search for recorded images or events by alarm, time, date, motion, video loss, camera number and ASCII cash register or ATM text.

Caution! This products primary purpose is to furnish video multiplexing and recording. Although the unit has alarm handling and motion detection functions, they are considered secondary features. This unit should not be the only alarm device on site.

Features

• Multiplexer functionality with built-in digital recording.

• Triplex simultaneous recording, playback, and live multiscreen viewing.

• Remote programming and control through the RS232, RS485 and Ethernet ports.

• View live or recorded images remotely using WaveReader software.

• Dual multiscreen monitor displays.

• Video motion detection (intrusion and activity).

• Motion search.

• Record speed selectable per camera.

• Displays include full screen, sequenced, picture-in-picture, and multiscreens.

• Alarm Handling with History Log. Pre- and post alarm recording, selectable per camera.

• Archive onto Calibur DVSe Disk Array, or RAID, DAT, AIT, or CD-Rs.

• PTZ control via ethernet or POTS, using CBR-KB3/J or KTD-405 keypad.

• Covert camera recording (recording without display).

• Daylight savings time change function.

• Alarm Notification via email and/or TCP/IP dialout notification.

0150-0193C 6 Calibur DVMRe Triplex

1.3 Passwords

Passwords are provided to limit access to menus and certain functions. Two levels of password security are provided:

• Operator: Limited menu access, only Operator and System View menus are available.

• Installer: Complete menu access.

As a security measure, it is recommended that the Operator and Installer passwords be changed after installation is complete (see section 3.20). Store the passwords in the administrator’s secure files.

Default Passwords

Four-Channel Units

Password

Type

Operator

Installer

Factory

Defaults

Language

Ethernet

Access

Reset

Access

Level Function

Operator

Installer

Provides access to the Operator

and SystemView menus.

Provides access to all on-screen

Resets the multiplexer to the

factory defaults.

Provides access to the On-screen

Language menu.

Deactivates the ethernet

password, so that the unit may be

accessed by any PC equipped with

Ten and Sixteen-Channel Units

Password

Type

Access

Level Function

menus.

WaveReader.

Changeable

by user?

Yes

Changeable

by user?

Default

Password

Press ‘ENTER’

4 Times

3 4 4 4

4 1 1 1

1 4 1 4

1 1 1 1

Default

Password

Operator

Installer

Factory

Defaults

Language

Ethernet

Access

Reset

0150-0193C 7 Calibur DVMRe Triplex

Operator

Installer

Provides access to the Operator

and SystemView menus.

Provides access to all on-screen

menus.

Resets the multiplexer to the

factory defaults.

Provides access to the On-screen

Language menu.

Deactivates the ethernet

password, so that the unit may be

accessed by any PC equipped with

WaveReader.

Yes

Press ‘ENTER’

4 Times

3 4 7 7

8 1 1 1

5 4 1 5

1 1 1 1

1.4 Unpacking

Check the package and contents for visible damage. If any components are damaged or missing, do not attempt to use the unit, contact the supplier immediately. If the unit must be returned, it must be shipped in the original packing box.

Package Contents

• The DVMRe Triplex unit.

• The Alarm Interface Circuit Board (P/N 0090-0077).

• Accessory PCB (P/N 0900-0127). Audio equipped models only.

• The User Manual (P/N 0150-0193).

• A WaveReader Software CD (P/N 0151-0005-25W11).

• The WaveReader Software Manual (P/N 0150-0143).

• The Archiving Addendum (P/N 0150-0194).

• WaveWatch User Manual (P/N 0150-0189).

• Power Supply (P/N 4310-0020)

• Power Cord ( NTSC P/N 4310-0002) (PAL P/N 4310-0001)

1.5 Installation Environment

Power: Ensure that the installation site’s AC power is stable and within the rated voltage of the 12

Volt DC power supply. If the site’s AC power is likely to have spikes or power dips, use power line conditioning or an Uninterruptable Power Supply (UPS).

Ventilation: Ensure that the location planned for the installation of the unit is well ventilated. Take note of the locations of the cooling vents in the unit’s enclosure, and ensure that they are not obstructed.

Temperature: Consider the unit’s operating temperature (0 to 40 °C) and non-condensing humidity specifications (10% to 80%) before choosing an installation location. Extremes of heat or cold beyond the specified operating temperature limits may cause the unit to fail. Do not install the unit on top of other hot equipment. Leave space between rack mounted units.

Moisture: Do not expose the unit to rain or moisture. Moisture can damage the internal components. Do not install the unit near sources of water.

Chassis: Other equipment may be placed on top of the unit if it weighs less than 35 pounds (16 kilograms).

1.6 Associated Equipment

Associated equipment in a typical security system could contain the following items:

• Two monitors

• A Keyboard (KB3 or KTD405).

• Video cameras: Composite video, 1 volt peak-to-peak.

• Alarm input devices: Pressure sensors, motion detectors, etc.

• Alarm output devices: Buzzers, Sirens, Flashing Lights, etc.

• A PC connected via ethernet cable.

0150-0193C 8 Calibur DVMRe Triplex

• An external archive device, such as a DVSe, RAID, CD-R, DAT, or AIT drive.

RS-485/1

ETHERNET

RS-485/2

RS-232/2

2345678

121314

For instructions regarding the connection of the associated security equipment in your system, please consult the instruction manual of the associated equipment.

1.7 The Back Panel

AUX

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

SVHS

SCSI

12V DC

RS-232/1

10/100

10 11

1. Camera Inputs: BNC connector, looping. Auto Terminating.

2. Composite Monitor-A Output: Composite video output with BNC style connector.

3. Y/C Monitor-A Output: Y/C video output with 4-pin mini-DIN style connector.

4. Alarm I/O: For connecting alarm inputs, and alarm output relays.

5. Power Input: For connecting the power supply.

6. Aux Port: For connecting the Accessory PCB for Audio inputs and outputs.

7. RS485 Port 1 Connector: For connecting to keyboard and other RS485 devices.

8. 10/100 Ethernet Port: For connecting to remote PC via ethernet network.

9. Composite Monitor-B Output: Composite video output with BNC style connector.

10. Y/C Monitor-B Output: Y/C video output with 4-pin mini-DIN style connector.

11. SCSI Port: For connecting SCSI compatible archive devices.

12. RS232 Port 1: For modem connection and external control of the unit.

13. RS485 Port 2 Connector: For connecting to keyboard and other RS485 devices.

14. RS232 Port 2: For Event Generation and ASCII Text insertion.

Camera Inputs

There are two BNC jacks for each camera. Either jack can receive a camera signal. The signal is looped (directly connected to the other jack), making the camera signal available to other equipment.

Cable: 75-Ohm Coaxial Connectors: BNC Auto Terminating: Yes

The camera input connectors are Auto Terminating.

Passive Looping: Yes

This means that the input signal will automatically be terminated with 75-Ohms unless a 2nd cable is connected to the 2nd BNC connector of the same camera input. Make sure there is 75-Ohm termination at the end of the video line if the signal is looped through the DVMRe Triplex.

Time base correction is performed during digital capture. As a result, cameras do not require synchronization.

See section 3.14 for information about disabling unused camera jacks in the menu system.

0150-0193C 9 Calibur DVMRe Triplex

Composite Monitor Output

A 7

G N D

When connecting directly from the DVMRe Triplex to the monitor, select the 75-Ohm impedance setting on the monitor.

If an additional device is connected to the monitor’s looping output, set the termination of the additional device as 75-Ohm, and set the termination of the monitor as Hi-Z (High Impedance).

Cable: 75-Ohm Coaxial Connectors: BNC

Y/C Monitor Output

Y/C video output has a 4-pin mini-DIN style connector. This style of connection is also referred to as SVHS and S-Video.

Cable: 75-Ohm Coaxial Connectors: BNC

Alarm I/O Port

The back panel of the unit is equipped with an Alarm

Port (DB-25 style connector).

Do not attempt to wire directly to the DB-25

connector on the back panel.

DB-25 Connector on Back Panel

Connect the Alarm PCB (supplied with the unit) to the Alarm Port. Wire all alarm inputs to the Alarm PCB per the pin out specifications shown below.

Pin 1: Alarm Input 1.

Pin 2: Alarm Input 2.

Pin 3: Alarm Input 3.

Pin 4: Alarm Input 4.

Pin 5: Alarm Input 5.

Pin 6: Alarm Input 6.

Pin 7: Alarm Input 7.

Pin 8: Alarm Input 8.

Pin 9: Alarm Input 9.

Pin 10: Alarm Input 10.

Pin 11: Alarm Input 11.

Pin 12: Alarm Input 12.

Pin 13: Alarm Input 13. Pin 14: Alarm Input 14. Pin 15: Alarm Input 15. Pin 16: Alarm Input 16. Pin 17: Alarm Output Relay #1. Pin 18: Ground. Pin 19: Ground. Pin 20: Ground. Pin 21: Alarm Output Relay #1 Common. Pin 22: Alarm Output Relay #2. Pin 23: External Alarm Silence and Acknowledge Input. Pin 25: Alarm Output Relay #2 Common.

Signal

NO1A1 A2A14 A15 A16A3 A4 A5 GND

171 214 15 163 4 5 18 7196

22 21 208910 202311241213 25

GNDA6

Signal

NO2 COM1

A8A9A10 GNDACKA11VextA12A13 COM2

Alarm PCB

Active alarm inputs vary by DVMRe model. 4 channel units (4CT) have 4 active alarm inputs. 10 channel units (10CT) have 10 active alarm inputs.

Alarm Input

An alarm condition can be activated by devices such as pressure pads, passive infrared detectors, door switches, or other similar devices.

0150-0193C 10 Calibur DVMRe Triplex

See section 3.11 for information about configuring the contacts as Normally Open or Normally Closed

pins 18

Normally Closed

DVMRe Triplex DB25 Connector

(Closes During Alarm)

Alarm Input No. 16

Ground

Output Relay No. 2

Output Relay No. 1

in the menu system.

Normally Open, Zero Potential Relay Contact: Configure in menu as Normally Open. Normally Closed, Zero Potential Relay Contact: Configure in menu as Normally Closed

TTL Active High: Configure in menu as Normally Closed.

TTL Active Low: Configure in menu as Normally Open.

Open Collector Active On: Configure in menu as Normally Open. Open Collector Active Off: Configure in menu as Normally Closed.

Alarm Input No. 1

Alarm Input No. 2 - 15

pin 1

pins 2-15

pin 16

Refer to each alarm device's manual for specific wiring details.

Typical wiring for Alarm #1 as Normally Open and Alarm #16 as Normally Closed.

Normally Open and Normally Closed Connections

Alarm Relay Output

The alarm relay output is activated when an alarm condition

exists. The alarm output is only active for the duration of the

alarm.

Output: Zero potential relay contacts, programmable in menu system as Normally Open or Normally Closed.

High: 5V (12V Tolerant) Low: Ground Inputs: 1 per channel.

Normally Open

Typical Alarm Device

(Opens During Alarm)

Typical Alarm Device

Alarm relays can be programmed in the menu system to

respond to macros, and video loss. See section 3.11 for

information about configuring the alarms in the menu system.

Typical wiring for Alarm Relays. Relays may be programmed Normally Open or Normally Closed.

pin 17

Alarm

Device

pin 21

pin 22

Controlled

pin 25

Device

DVMRe Triplex DB25 Connector

Voltage: 30V (Max) Current: 500mA (Max)

Power

Source

Power

Source

0150-0193C 11 Calibur DVMRe Triplex

External Alarm Acknowledge Input

123456789

GND

#24 AWG, twisted pair with shield

Connect a switch or similar device to ground this pin in order

to acknowledge an alarm condition, and silence associated

buzzers and relays. Connect from pin 23 to either pin 18, 19,

or 20 (ground pins).

External Device: Normally Open Zero potential relay contact.

NOTE

All specifications subject to change without notice. GE-Interlogix believes all specifications to be correct at time of printing, but no liability is assumed for omissions or errors.

AUX Port

The back panel of the unit is equipped with an Aux Port

(DB-9 style connector).

Do not attempt to wire directly to the DB-9

connector on the back panel.

DB-9 Connector on Back Panel

Connect the Accessory PCB (supplied with the audio equipped models) to the AUX port to access the Audio features. Wire the audio input and output to the Accessory PCB per the pin out specifications shown below.

Pin 1: Not Used. Pin 2: Audio Out. Pin 3: Ground. Pin 4: Audio In. Pin 5: Ground. Pin 6: Not Used. Pin 7: Ground. Pin 8: Not Used. Pin 9: Ground. GND: Ground.

Accessory PCB

RS485 Connector

Shields are grounded at one end, preferably at the

DVMRe Triplex.

See section 3.16 for information about configuring

the RS485 network address settings in the menu

system.

Wire Type:

(2-wire)

Connector Type: RJ-45 Max. Cable Length: 3200 feet / 1000 meters

RJ-45 Pin Configuration For RS485 Port

Pin Use

1 Ground (Shield) 5 Not Connected 2 Not Connected 6 Network -VE 3 Network +VE 7 Ground (Shield) 4 Not Connected 8 Not Connected

0150-0193C 12 Calibur DVMRe Triplex

82 3 4 5 6 71

RJ-45 socket on

back panel.

Ethernet Port

The cable connection configuration depends on your

network configuration:

• For a DVMRe Triplex that connects directly to a Hub or Switch, use a straight through connection.

• For a DVMRe Triplex that connects directly to a PC, use a cross over connection.

Consult with your MIS personnel for the specific type of configuration. See section 3.16 for information about configuring the ethernet settings in the menu system.

Wire Type: Cat 5 Connector Type: RJ-45 Max. Cable Length: 100 meters / 328 ft. Min. Cable Length: 6 feet / 1.8 meters Hub Wiring Configuration: Straight Through PC Wiring Configuration: Cross Over

RJ-45 Pin Configuration For Ethernet Port

Pin Use

1 TX+ 5 Not Connected 2 TX- 6 RX-

Pin Use

82 3 4 5 6 71

3 RX+ 7 Not Connected 4 Not Connected 8 Not Connected

RJ-45 socket on

back panel.

SCSI Port

The unit is equipped with a SCSI port for connecting external archive devices. The unit only supports a single SCSI device. The SCSI ID of the archive device must be set to 0.

The SCSI bus must be terminated, otherwise the system will not operate properly.

Additional menu setup may be necessary to configure archive device. See section 3.15.

Connector: 50 Pin, High Density SCSI-2. Gender (on unit) : Female Compatible devices : DVSe, RAID, DAT, AIT,

CD-R, CD-RW

SCSI ID : 0

RS232 Port 1

For a Modem connection or remote control of unit. See section 3.16 for information about configuring the modem settings in the menu system. See section 8 for RS232 Remote Control Protocols.

DB-9 Pin Configuration For Port 1

Pin Use

1 DCD 4 DTR 7 RTS 2 RX 5 Ground 8 CTS

DB-9 on back panel.

3 TX 6 Not Connected 9 Not Connected

0150-0193C 13 Calibur DVMRe Triplex

RS232 Port 2

For Event Generation and ASCII Text Insertion.

RJ-45 Pin Configuration For RS232 Port 2

Pin Use

1 Ground 5 TXD 2 Reserved 6 Not Connected

Pin Use

82 3 4 5 6 71

3 Not Connected 7 Ground 4 RXD 8 Reserved

RJ-45 socket on

back panel.

1.8 Power-Up

It is important that the power-up procedures be followed carefully. The unit uses its auto-detect feature to detect camera signals during power-up, and configure itself automatically.

Power-up procedure

Once the system installation is complete, apply power in the following order:

Voltage: 12 Volt DC

1. Energize the monitors and all of the cameras. Power: 60 Watt (5 Amp)

2. Energize the DVMRe Triplex. Connector: 2.1mm barrel, center positive

Once power is applied to the unit, it will begin its power-up procedure. The unit will begin by displaying the software version on Monitor-A, then the unit will begin recording automatically.

Check Video Input Quality

Check the picture quality by selecting each camera for full screen display. If the picture quality is poor, check the following items:

Power Supply Input

• The BNC connections.

• The loop-through terminations.

• The video levels of incoming signals.

• The possibility of ground loops.

• Consult the camera’s installation instructions for additional information about proper camera setup.

Check Record And Playback Quality

Record for at least three minutes at the default record rate. Then play back the recording, selecting each camera for full screen display. Check the playback picture quality.

1.9 Minimum Recommended Menu Setup

After installation is complete, it is strongly recommended that, as a minimum, the items in the QuickInstall menu be configured before the unit is used. All the features located in the QuickInstall menu are also found in the Main menu. These items are provided in the separate QuickInstall menu as a convenience for the installer.

For information about accessing and configuring the menu system, see Section 3.

0150-0193C 14 Calibur DVMRe Triplex

To find detailed information in this manual about configuring each item in the QuickInstall menu, use the following table to locate the main menu location of each item in the QuickInstall menu.

QuickInstall

Menu Item

Change the time Change the date Edit Camera

Titles Camera Disable Record Quality

Installer Password

Auto Disable Now

Main Menu Location

Main Menu → Time/Date → Set Time Main Menu → Time/Date → Set Date Main Menu → Camera Setup → Camera Titles → Edit Titles

Main Menu → Camera Setup → Camera Disable Main Menu → Record → Record Quality Main Menu → Passwords → Installer Password

Main Menu → Camera Setup → Camera Disable → Auto Disable Now

Section in

Manual

3.8

3.14

3.10

3.20

3.14

0150-0193C 15 Calibur DVMRe Triplex

2 DMVR

Triplex Basic Operations

2.1 Principal Operating Modes

The DVMRe Triplex has three principal modes of operation:

• Live Viewing.

• Playback.

• Recording.

All three of these modes can operate simultaneously. Each mode is discussed in detail later in this section.

2.2 The Front Panel

1. Multiscreen Selection Buttons: 16, 10, 7, and 4 way.

2. Monitor Selection Button: Monitor A or Monitor B.

3. Multiscreen Selection Buttons: 13, 9, 6 way, and Picture-in-Picture.

4. Camera Selection Number buttons: Camera numbers 1 through 16.

5. Reverse Play Button: Playback in Reverse.

6. Freeze Button: Freezes camera images on-screen in Live mode. Pauses Playback.

7. Play Forward Button: Begins Playback.

8. Jog/Shuttle: Controls Playback speed and Menu selections.

9. Menu Button: Provides access to on-screen menus.

10. Power Indicator: Indicates power on/off condition.

11. Alarm button: Allows user to acknowledge and silence alarms.

12. Sequence Button: Sequences camera views.

13. Zoom Button: Provides a 2X digital zoom.

14. Function Button: Used in conjunction with Camera Buttons to run Macros.

15. Record Button: Used to Start and Stop Recording.

16. Stop Button: To stop Playback and return to Live mode.

17. Search Button: Access to stored video data.

18. Enter Button: Confirms selection in menus.

0150-0193C 16 Calibur DVMRe Triplex

2.3 Live Viewing

Multiscreen Display

In Live Multiscreen mode, press one of the Multiscreen buttons to activate the multiscreen display on Monitor-A or Monitor-B. Live Multiscreens are displayed with gray borders. For detailed information about Multiscreen displays, see section 2.6.

Multiscreen Display With Sequencing

If a multiscreen display does not include all of the cameras, the remaining cameras can be sequenced in the bottom right cameo. While in a multiscreen display, press the Sequence button to begin sequencing. For detailed information about sequencing, see section 2.8.

Full Screen Display

Select any camera for Full Screen display by pressing the Number button of the desired camera. Pressing the Camera number button again displays the Status Display Box. Pressing the same button a third time displays any associated ATM or cash register ASCII text, see section 2.9.

Sequenced Full Screen Display

While in a Full Screen display, press the Sequence button to begin full screen sequencing. The sequence list and dwell times are programmable. For detailed information about programming the sequence list see section

2.8. For detailed information about configuring the dwell times in the menu system, see section 3.9.

Multiscreen Buttons

Sequence Button

Number Button

Sequence Button

Zooming

To activate the 2x digital zoom, select the full screen display of the camera you wish to zoom, then press the Zoom button. Zooming will be indicated by the LED located directly above the Zoom button. Zooming is also indicated as ZOOM on the primary monitor. Zooming works with frozen and non-frozen images. Zoomed images can also be frozen.

While Zoomed, rotate the Jog/Shuttle to Pan and Tilt across the image. Please note, the camera does not move during digital Pan/Tilt.

Press the Zoom button again to cancel the Zoom operations.

If the Zoom button is pressed while in a multiscreen display, the camera from the last active

NOTE

cameo is selected for full screen display. Press the Zoom button again to activate the Zoom operation.

Freezing

Pressing the Freeze button freezes all camera images on-screen. Full Screen freezing is indicated as FRZ on-screen. Multiscreen freezing is indicated as * (a flashing asterisk) in each frozen cameo.

Individual cameos can be frozen in Active Cameo mode (see section 2.7).

Zoom Button

with LED

Freeze Button

Press the Freeze button again or any camera button to cancel Freeze operations.

0150-0193C 17 Calibur DVMRe Triplex

Selecting Monitor-B

To control Monitor-B, press the lower part of the Monitor button. The Monitor-B LED will light to indicate that the number keypad now controls Monitor-B. Press the upper part of the Monitor button again to return the keypad control to Monitor-A.

Monitor Button

2.4 Playback

Playback always displays on Monitor A. Playback multiscreen borders are black, as opposed to the gray borders of the live multiscreens. Monitor B continues to display full or multiscreen live images in playback mode. To begin playback, press the Play Forward or Reverse Play button.

Play Forward

When the Play Forward button is pressed, the unit will play forward at the rate the data was recorded. While in Playback mode, the user may change the playback direction, playback speed, etc. To return to Play Forward operations, press the Play Forward button.

Reverse Play

To begin reverse playback, press the Reverse Play button.

Play Forward

Button

Fast Forward

During playback, rotate the Shuttle (the outer dial) clockwise to view data at a higher than normal rate. Increasing the amount of rotation increases the rate of playback.

Rewind

During playback, rotate the Shuttle counter-clockwise to view data (in reverse) at a higher than normal rate. Increasing the amount of rotation increases the rate of playback.

Freeze

During playback, press the Freeze button. This feature pauses all full screen and multiscreen images

Single Frame Advance & Single Frame Rewind

During Freeze or Pause mode, rotate the Jog (the inner dial) to view the frame directly before or after the frame displayed on-screen.

Reverse Play

Button

Jog / Shuttle

Freeze Button

0150-0193C 18 Calibur DVMRe Triplex

Stop Playback

To stop playback and return to Live Multiscreen mode on Monitor A, press the

Stop button.

Multiscreen Display

During Playback, press one of the Multiscreen buttons to activate a multiscreen display. The 6-way and PIP multiscreen displays are not available in Playback mode. For detailed information about Multiscreen displays, see section 2.6.

Multiscreen Display With Sequencing

Full Screen Display

Sequenced Full Screen Display

2.8. For detailed information about configuring the dwell times in the menu system, see section 3.9.

Zooming

To activate the 2x digital zoom, select the full screen display of the camera you wish to zoom, then press the Zoom button. Zooming will be indicated by the LED located directly above the Zoom button. Zooming is also indicated as ZOOM on the monitor. Zooming works with frozen and non-frozen images. Zoomed images can also be frozen.

While Zoomed, use the Jog/Shuttle to Pan and Tilt across the image. Please note, the camera does not move during digital Pan/Tilt.

Stop Button

Multiscreen Buttons

Sequence Button

Number Button

Sequence Button

Zoom Button

with LED

Press the Zoom button again, or another camera button to cancel the Zoom operations.

If the Zoom button is pressed while in a multiscreen display, the camera from the last active cameo is selected for full screen display. Press the Zoom button again to activate the Zoom operation.

Searching Recorded Data

The DVMRe Triplex has a powerful search interface feature that allows the user to search for data on the internal hard disk or an external archive device. The user may search the data for previous recording sessions, text insertion, alarm conditions, or for motion in a selectable area of the scene.

0150-0193C 19 Calibur DVMRe Triplex

Because the search interface is so dynamic, the search interface is covered in detail in a separate

Monitor A

Monitor B

section of this manual. See section 5.

2.5 Recording

To begin recording, press the Record button. Recording will be indicated by the LED located directly above the Record button. The unit always starts recording at the end of previously recorded data.

The unit will continue recording until the record button is pressed again.

Monitor Displays During Recording

Multiscreen Live and Playback display on Monitor A and Monitor B are not affected by recording operations.

Record Button

LIVE

PLAY

BACK

LIVE

PLAY

LIVE

BACK

0150-0193C 20 Calibur DVMRe Triplex

2.6 Display Options

Monitor A

Monitor B

Available Multiscreen Displays

Press the Multiscreen buttons to activate the multiscreen display. Pressing the individual multiscreen button will display the corresponding multiscreen.

10-Way

7-Way

16-Way

4-Way

9-Way

6-Way

PIP

13-Way

The multiscreen display is limited to the number of camera inputs on the unit.

Sixteen-Channel unit: Capable of displaying all multiscreens. Ten-Channel unit: Only capable of displaying 10-way through 4-way multiscreen and PIP. Four-Channel unit: Only capable of displaying 4-way multiscreen and PIP.

The camera assignments for each multiscreen is retained (in non-volatile memory) for both Live and Playback multiscreen mode on Monitor A, as well as Live multiscreen mode on Monitor B.

PIP: Use the Jog/Shuttle to adjust the location and size of the PIP display. Please note that the PIP display is only available on Monitor A in Live mode, when Monitor B is in fullscreen display mode.

2.7 Active Cameos

A cameo is defined as any cell within a multiscreen display. Active Cameo mode allows the user to access and edit each cameo individually.

Entering Active Cameo Mode

While viewing a multiscreen, enter Active Cameo mode by pressing the Enter button. Active Cameo mode is indicated on-screen by flashing the number and titles of the active cameo and the LED above the Enter button is lit. By default, the top left cameo is activated.

Selecting Cameos

Select a cameo using the Jog/Shuttle to navigate the multiscreen. Rotating the Jog selects the next screen up or down a row. Rotating the shuttle selects the next screen in numerical order. The active cameo will always be indicated by the flashing camera number and titles.

0150-0193C 21 Calibur DVMRe Triplex

Enter Button

Jog/Shuttle

Selecting Cameras

Display any camera in the active cameo by pressing the Number button of the desired camera. Once a camera has been selected, the active cameo advances to the next cameo on the right.

Number Button

The camera selection only changes the multiscreen currently being displayed. Each multiscreen must be configured separately. Changes to the multiscreen display are saved in non-volatile memory, and will be retained even if power is removed from the unit.

Freezing

Press the Freeze button to freeze the image in the selected cameo. Each frozen cameo is indicated as * (a flashing asterisk) on-screen.

Press the Freeze button again to cancel Freeze operations.

Freeze Button

2.8 Sequencing

The sequencing feature allows a camera to be displayed briefly on-screen, before advancing to the next camera in the sequence list. The default sequence list displays each camera in numerical order.

Sequence Button

Dwell Time

The dwell time is the amount of time each camera is displayed on-screen before advancing to the next camera. The Full Screen and Multiscreen Dwell Times are separately programmable in the menu system. For detailed information about configuring the dwell times in the menu system, see section

3.9.

Autolist™ Custom Sequence List

The Autolist™ feature allows the user to create a custom sequence list, controlling the order the cameras are displayed and the dwell time. Separate Autolists may be created for Monitor A (Live and Playback mode) and Monitor B (Live mode). Using the Monitor button, select the monitor to be programmed. Then, using a Number button, select any camera for full screen display.

The unit must be in Full Screen Display mode before starting to create the sequence list.

NOTE

To begin recording the Autolist™ sequence: Press the Alarm button and Sequence button simultaneously. Autolist Program mode is indicated as PGM on-screen.

Recording starts when the first camera number is pressed. Press the camera numbers in the order you wish them to appear on-screen. The amount of time between button presses determines the Dwell Time. During sequence list programming, pressing any button other than a Number button or the

Sequence button voids the sequence list.

To end the recording: Press the Sequence button. The amount of time between pressing the last Number button and the Sequence button determines the dwell time for the final camera in the

sequence list.

This initial camera is not part the sequence list.

Alarm Button and

Sequence Button

Returning To The Default Sequence List

The default sequence list is all cameras in numeric order with a three second dwell time.

0150-0193C 22 Calibur DVMRe Triplex

To return the unit to the default sequence list, go to the Main Menu → Sequencing → Full Screen

Dwell menu. Select 03 seconds by rotating the Jog, then press the Enter button. Note: Any alteration of the dwell time from this menu will cancel the sequence list and return to the

default (numeric) order.

Sequencing In Cameos

While viewing a multiscreen display, additional cameras (cameras not shown in the multiscreen display) can be sequenced in the lower right hand cameo by pressing the Sequence button. The sequence list is not programmable, but the dwell time can be adjusted in the menu system. Press the

Sequence button again to cancel sequencing.

2.9 On-screen Indicators

There are five types of on-screen indicators.

Camera Titles: Displays the camera number and the camera title. Status Indicators: Displays Time, Date, and Hard Disk record time left. Conditional Indicators: Displays indicators for Freeze, Zoom, Alarm, Motion Detection, Videoloss,

Autolist™ Program mode, Macro Record and Macro Playback mode. Status Display Box: Displays Archive Device, Network status and Image Quality Setting (Playback

mode only).

Text Display Box: Displays ATM/POS Text data.

Camera Titles

Camera Titles are displayed on either the upper or lower corner of the left hand side of the screen. The camera title can be changed in the menu system (see section 3.14). The user can change display position and color. See below.

Changing Position And Color Of Title And Status Indicators

Camera Titles: To change the color and position of the camera

titles, select a camera for full screen display, then press the Enter button to advance to the next display setting. Repeatedly pressing the Enter button advances the display settings through the sequence show in the table on the right.

Status Indicators & Camera Titles: Select Camera 1 for full screen display. Using the Enter button, cycle through the sequence shown on the right. Each time the position cycle is completed, the unit advances the Status Indicator color. Choose Black, White or Gray.

Position Color

Top Left Black Top Left White Top Left Gray Bottom Left Black Bottom Left White Bottom Left Gray

Title not displayed

Status Indicators

Status indicators are displayed on the upper right hand corner of the screen.

Status indicators include:

• Time and Date (these can be turned off in the menu system, see section 3.8). The Time and Date format can also be changed in the menu system.

• Time remaining on Hard Disk(s).

0150-0193C 23 Calibur DVMRe Triplex

Small Cameo

Conditional Indicators

Condition Full Screen Indicator Multiscreen Indicator

Alarm

Autolist™ Program

mode

Freeze

Macro Record mode

Motion Detection

Videoloss

Zoom

F followed by macro number F followed by macro number

ALM A in cameo of camera in alarm

PGM PGM

FRZ

M M in cameo w/ motion detection

VDL V in cameo with videoloss

ZOOM ZOOM

(Asterisk) in frozen cameo

Status Display Box

A Status Display Box can be viewed by pressing the Camera Number button twice. Status Indicators include:

On Live Fullscreen:

• Archive Status: Not Connected, Not Ready, Ready, Ejecting, Play, and timeleft. Timeleft indicates the amount of time before the archive medium is full (Only available if the unit has Background Archiving turned On).

• Network: Displays all current Network connections. Normal connection is displayed as ip.ip or --if there is no connection. Live connections are displayed as E1: ip.ip , E2: ip.ip, etc. (where ip.ip represents the last 2 bytes of the IP Address). POTS connection is displayed as IP 1.1.

On Playback Fullscreen:

• All the above, including Image Quality Setting: High, Medium, Standard.

ATM/POS Text Display

Pressing the Camera Number a third time displays an ATM/POS text display. This feature can be used during live viewing mode to verify that the DVMRe Triplex is receiving ATM/POS text, or in Playback mode to review recorded text and video.

0150-0193C 24 Calibur DVMRe Triplex

2.10 Triplex Mode

Triplex mode allows the display of both live and playback images to appear on Monitor A simultaneously. Live images have gray borders, while playback images have black borders.

To enter Triplex mode, press the Play Forward button while in Play Forward mode. Alternatively, press the Play Reverse button while in Play Reverse mode. Both the Play Forward LED and the Stop LED turn on to indicate that the unit is in Triplex mode.

Monitor B always switches to a fullscreen live display whenever Triplex mode is entered.

Play Forward

When in Play Forward mode and the Play Forward button is pressed, the unit will enter the Triplex mode of operation. When Play Forward is pressed again, the unit will revert back into the normal Playback mode. While in the Triplex mode, if reverse play is in progress, the Play Forward button will change the playback direction.

Reverse Play

When in Reverse Play mode and the Reverse Play button is pressed, the unit will enter the Triplex mode of operation. When Reverse Play is pressed again, the unit will revert back into the normal Playback mode. While in the Triplex mode, if forward play is in progress, the Reverse Play button will change the playback direction.

Fast Forward

During Triplex mode, rotate the Shuttle (the outer dial) clockwise to view playback images at a higher than normal rate. Increasing the amount of rotation increases the rate of playback. Live images are not affected.

Play Forward

Button

Reverse Play

Button

Rewind

During Triplex mode, rotate the Shuttle counter-clockwise to view playback images (in reverse) at a higher than normal rate. Increasing the amount of rotation increases the rate of playback. Live images are not affected.

Freeze

During Triplex mode, pressing the Freeze button pauses all multiscreen images, both Live and Playback.

Single Frame Advance & Single Frame Rewind

During Freeze or Pause mode, rotate the Jog (the inner dial) to view the frame directly before or after the frame displayed on-screen. Only the playback images are affected.

Stop

To stop Triplex mode and return to Live mode on Monitor A, press the Stop button.

Jog / Shuttle

Freeze Button

Stop Button

0150-0193C 25 Calibur DVMRe Triplex

Multiscreen Display

During Triplex mode, press one of the Multiscreen buttons to activate a multiscreen display. The 6-way and PIP multiscreen displays are not available in Triplex mode. For detailed information about Multiscreen displays, see section 2.6. The Live and Playback images in a multiscreen display may be transposed by pressing the multiscreen button that corresponds with the current multiscreen display.

E.g. If the current display is a 13-way multiscreen with the center cameo being a playback image and the rest of the cameos being live images, pressing the 13-way multiscreen button will result in the center cameo being live and the rest of the cameos being playback images.

Multiscreen Buttons

Multiscreen Display With Sequencing

The bottom right cameo of any multiscreen will start sequencing when the Sequence button is pressed. If this camera is a playback image, the sequencing will include all the non-displayed playback cameras, and vice versa for a live image.

Sequence Button

Full Screen Display

Number Button

Sequenced Full Screen Display

2.8. For detailed information about configuring the dwell times in the menu system, see section 3.9.

Sequence Button

Zooming

To activate the 2x digital zoom, select the full screen display of the camera you wish to zoom, then press the Zoom button. Zooming will be indicated by the LED located directly above the Zoom button. Zooming is also indicated as ZOOM on the monitor. Zooming works with frozen and non-frozen images. Zoomed images can also be frozen.

While Zoomed, use the Jog/Shuttle to Pan and Tilt across the image. Please note, the camera does not move during digital Pan/Tilt.

Zoom Button

with LED

Press the Zoom button again, or another camera button to cancel the Zoom operations.

NOTE

If the Zoom button is pressed while in a multiscreen display, the camera from the last active cameo is selected for full screen display. Press the Zoom button again to activate the Zoom operation.

0150-0193C 26 Calibur DVMRe Triplex

3 Menu System Overview

3.1 Menu Notation In This Manual

In the following sections, there are headings like this:

q Main Menu → Time/Date → Set Time

Meaning: From the Main Menu, select Time/Date, then press the Enter button. The Time/Date menu

will appear. From the Time/Date menu, select Set Time, then press the Enter button. A pop-up or pull-down menu will appear.

Selected Items

Items selected in the menu system are represented in the manual as follows:

Selected Not Selected

Time/Date Time/Date

3.2 Accessing The Menu System

Enter the menu system by pressing the Menu button. A Password Box will appear on the primary monitor. Enter either the:

• Operator Password: Providing limited access to the menu system. Only the Operator and System View menus are available.

Menu Button

• Installer Password: Providing complete menu access. Use the Number buttons to enter the appropriate password. Default passwords are provided in the beginning of this manual, in section 1.

3.3 Available Menus

Main QuickInstall

Time/Date Sequencing Record Alarms Macro Motion Detection Camera Setup Archive Setup Audio Setup Communications Front Panel Lock Factory Settings Passwords

Change the time Change the date Edit Camera Titles Camera Disable Record Quality Installer Password Auto Disable Now

Operator SystemView

Sequencing Time/Date Display Titles Display Alarm History Archive Setup Operator Password

About DVMR View Screen 1 View Screen 2 View Screen 3 View Screen 4 View Screen 5 View Screen 6 View Screen 7 View Screen 8

0150-0193C 27 Calibur DVMRe Triplex

3.4 Menus In This Manual

QuickInstall

Shuttle

Each menu is covered in detail in this chapter of this manual. Menus and Menu Items appear in the manual in the same order they appear on-screen.

• Main Menu

• QuickInstall Menu

• Operator menu

• SystemView Menus

3.5 Navigating The Menu System

Selecting a Menu from the Menu Bar: When the menu system is first accessed, only the menu bar is displayed. Use the Shuttle to select the desired menu.

Opening the Drop Down Menus: Rotate the Jog. Navigating in Menus: Rotate the Jog to highlight items in the drop-down menus. Selecting Menu Items: Hit the ENTER button to select the highlighted menu item. Exiting Menus: Press the Menu button to exit a menu. From the menu bar, press the Menu button

to exit the menu system completely.

Main

Time/Date Sequencing Record Alarms Macro Motion Detection Camera Setup Archive Setup Audio Setup Communications Front Panel Lock Factory Settings Passwords

Jog

Operator SystemView

Jog

3.6 Menu Shortcuts

Zoom Button: In menu lists that have 2 settings per camera, the Zoom button will toggle all

selections. This provides a quick and easy way to enable or disable all cameras for a particular feature.

0150-0193C 28 Calibur DVMRe Triplex

Camera Button: In menu lists that provide settings per camera, a particular camera may be

accessed directly by pressing on the associated camera button. Rotate the Shuttle to modify the setting.

3.7 The Main Menu

Main Menu Overview

The Main menu contains the majority of programmable options for the DVMRe Triplex. Each item in the Main menu is described in detail in this section of the manual.

Main menu items appear in this section in the same order they appear in the menu.

3.8 Time/Date

Use this menu to specify:

• Which monitors will display the time and date.

• The time format: 12 or 24 hours.

• The date format: MM/DD/YY, YY/MM/DD, or DD/MM/YY.

• The time and date.

• Whether the unit’s clock is a master or slave.

q Main Menu → Time/Date → Time / Date Display

Use this menu to specify if the time and date will be displayed on:

• Monitor-A.

• Monitor-B.

• Both Monitors.

• Not Displayed

Rotate the Jog to navigate, then rotate the Shuttle to change the values. Save changes and exit the menu: Select [OK], then press the Enter button.

Time/Date Display Set Time Format Set Date Format Set Time Set Date Set Master/Slave

Time/Date Display

Monitor A : Monitor B : ON

[CANCEL] [OK]

Exit the menu without making changes: Press the Menu button, or select [CANCEL], then press the Enter button.

q Main Menu → Time/Date → Set Time Format

Rotate the Jog to set the desired time format. Select from either:

• 12 Hour

• 24 Hour

Press the Enter button to confirm the selection and exit the menu. Press the Menu button to exit the menu without making changes.

0150-0193C 29 Calibur DVMRe Triplex

Time Format Setup

Select Format

12 HOUR

q Main Menu → Time/Date → Set Date Format

Time Setup

[CANCEL] [OK]

Date Setup

[CANCEL] [OK]

Master/Slave Select

Rotate the Jog to set the desired date format. Select from either:

• MM/DD/YY

• DD/MM/YY

• YY/MM/DD

Press the Enter button to confirm the selection and exit the menu. Press the Menu button to exit the menu without making changes.

q Main Menu → Time/Date → Set Time

1. Rotate the Shuttle to navigate, highlight HH MM SS.

2. Press the Enter button, the highlighting will move to the row of numbers.

Date Format Setup

Select Format

MM/DD/YY

3. Enter the time in Hours, Minutes, and Seconds. Rotate the Jog to change the values and the Shuttle to navigate.

HH MM SS

03 05 53

4. Press the Enter button to confirm the selection and exit the edit mode.

5. To save the changes and exit the menu: Rotate the Jog to select [OK], then press the Enter button.

6. To exit the menu without making changes: Rotate the Jog to select [CANCEL], then press the Enter button.

q Main Menu → Time/Date → Set Date

1. Press the Enter button, the highlighting will move to the row of

numbers.

2. Enter the date in Months, Days, Years. The day of the week is calculated automatically. Rotate the Jog to change the values and the Shuttle to navigate.

3. Press the Enter button to confirm the selection and exit the edit mode.

4. To save the changes and exit the menu: Rotate the Jog to select [OK], then press the Enter

button.

5. To exit the menu without making changes: Rotate the Jog to select [CANCEL], then press the Enter button.

MM DD YY Day

01 25 60 MON

q Main Menu → Time/Date → Set Master / Slave

If several multiplexers are installed and connected via RS485 a network, one of the multiplexers may be set as the master clock. This unit will control the date and time (including daylight savings time) for all of the other units.

Select One unit from the RS485 network as the master clock by selecting YES in this menu. All other units must be set as NO (Default).

0150-0193C 30 Calibur DVMRe Triplex

Master Clock

3.9 Sequencing

Fullscreen Dwell

Record Quality

Event Settings

Use this menu to specify:

• The multiscreen dwell time.

• The full screen dwell time.

The dwell time is the amount of time each camera is displayed on-screen (while sequencing) before advancing to the next camera.

q Main Menu → Sequencing → Multiscreen Dwell

Rotate the Jog to change the desired dwell time (from 1 to 30 seconds). The default is 3 seconds.

1. Press the Enter button to confirm the selection and exit the menu.

2. Press the Menu button to exit the menu without making changes.

q Main Menu → Sequencing → Fullscreen Dwell

Rotate the Jog to change the desired dwell time (from 1 to 30 seconds). The default is 3 seconds.

1. Press the Enter button to confirm the selection and exit the menu.

2. Press the Menu button to exit the menu without making changes.

Multiscreen Dwell

Fullscreen Dwell

Multiscreen Dwell

(Time in Seconds)

3.10 Record

Use this menu to:

• Specify the record quality: High, Medium, or Standard.

• Specify if a camera is to be used for event recording,

time-lapse recording, or both.

• Specify the time-lapse record rate per camera.

• Specify the event record rate per camera.

• Specify the activity record rate per camera.

• Specify the alarm record rate.

• Set the Record Lock feature.

• Perform disk maintenance by Deleting, Un-deleting, or

Destroying previously recorded video.

• Specify how the unit will handle data overwrite issues once the hard disk becomes full.

Record Timer

Timelapse Record Rate Event Record Rate Activity Record Rate Alarm Record Rate Record Mode Disk Maintenance Record Lock ADM

0150-0193C 31 Calibur DVMRe Triplex

Day Start Stop Macro ON/OFF

Record Quality

[CANCEL] [OK]

q Main Menu → Record → Record Timer

Use this menu to setup Preset Record Timer Events.

1. Rotate the Shuttle to select a timed event from the list.

2. Press the ENTER button to enter the Edit mode.

3. Rotate the Shuttle to navigate to the desired field.

4. Rotate the Jog to change the values of the selected field.

5. Press the Enter button to exit the Edit mode.

6. Rotate the Jog to highlight the [OK] field and press the ENTER button to save the changes.

q Main Menu → Record → Record Quality

Use this menu to specify the record quality for each camera. Decreasing the record quality decreases the amount of disk space required to store the images, due to a higher compression scheme.

Record Quality Picture Quality Disk Space Needed

High Excellent Most Medium Good Medium

22:59 01:59 NONE ON

MON-FRI 05:56 04:06 10 ON

-- --:-- --:-- -- --

[OK]

Hit ‘ENTER’ to toggle EDIT Mode

Camera 01:

High

Camera 02: High Camera 03: High Camera 04: High : :

Standard Fair Least

Camera 16: High

1. Rotate the Jog to navigate, and the Shuttle to change the values.

2. To save changes and exit the menu: Select [OK], then press the Enter button.

3. Exit the menu without making changes: Press the Menu button, or select [CANCEL], and then press the Enter button.

q Main Menu → Record → Event Settings

Use this menu to specify how each camera will record during normal and event conditions.

TL: Records at the Time-lapse Record Rate under normal conditions. Does not change record rate during an event.

Event: Records during events at the Event Record Rate. Camera does not record under normal conditions.

Event + TL: Records at the Time-lapse Record Rate under normal conditions. Records at the Event Record Rate during events.

Event Camera Settings

Camera : Type : TL Pre Event Duration : 00 Post Event Duration: 000

[CANCEL] [OK]

0150-0193C 32 Calibur DVMRe Triplex

About Events: An Event is an action that the unit acknowledges by recording at the

NOTE

Event Record Rate, yet it is not cause for an Alarm. Events may be created two ways, via RS232 text insertion and Activity detection.

Example of an Event: A camera is pointed at the front door inside the lobby during business hours. With the Event Camera Settings Type set to Event, the unit does not record while the doorway is empty. When activity motion detection senses that someone is entering or leaving the doorway, the unit begins recording at the Event Record Rate and stops recording when the motion ceases.

RS232 Event: See section 7 for information about generating an Event via RS232, and optionally inserting ASCII text to mark the Event.

Activity Detection Event: See Setup Parameters in section 3.13 for detailed information about configuring activity detection as an event in the menu system.

Pre Event Duration: The unit will record up to 5 seconds of data ahead of the event trigger, at the Event Record Rate. Select from 0 to 5 seconds.

Post Event Duration: The unit will record up to 250 seconds after the completion of the Event, at the Event Record Rate. Select from 0 to 250 seconds.

q Main Menu → Record → Timelapse Record Rate

The unit records at the Timelapse Record Rate under normal conditions, when there are no alarms, events, or activity present. Record rates are measured in both Pictures Per Second (pps) and Seconds Per Picture (spp).

The maximum record rate per camera is inversely proportional to the number of cameras connected to the unit. The fewer cameras connected, the higher the maximum record rate for each camera, and vice versa. The maximum record rate for multiple cameras is 48pps (NTSC)(40pps PAL). The maximum record rate for a single camera is 30pps (NTSC)(25pps PAL).

The bottom right corner of the menu contains a record duration calculator. The top line indicates the estimated recording time for the unit in Time-lapse record mode only. The bottom line indicates the estimated recording time, taking into consideration the amount of time the unit will spend in Activity, Event, and/or Alarm record mode.

Timelapse Record Rate

Camera 1 : Camera 2 : 0.29 pps 3.5 spp Camera 3 : 0.34 pps 2.9 spp Camera 4 : 0.57 pps 1.8 spp : : : Camera 15 : 0.40 pps 2.5 spp Camera 16 : 0.40 pps 2.5 spp

0.40 pps 2.5 spp

[CANCEL] [OK]

8 days 5 h (TL) 8 days 5 h (Total)

1. Rotate the Jog to navigate, and the Shuttle to change the values.

0150-0193C 33 Calibur DVMRe Triplex

2. To save changes and exit the menu: Select [OK], and then press the Enter button.

Estimate of the % of time each

camera will typically spend in

Event mode. For example if you

events each day, each lasting 3

minutes on average, then the %

3. To exit the menu without making changes: Press the Menu button, or select [CANCEL], then press the Enter button.

q Main Menu → Record → Event Record Rate

The unit will record at the Event Record Rate when an Event is activated. Events can be activated by RS232 ev ent generation or activity detection. See Event Settings on page 29.

Record rates are measured in both Pictures Per Second (pps) and Seconds Per Picture (spp). The maximum record rate per camera is inversely proportional to the number of cameras connected to

the unit. The fewer cameras connected, the higher the maximum record rate for each camera, and vice versa. The maximum record rate for multiple cameras is 48pps (NTSC)(40pps PAL). The maximum record rate for a single camera is 30pps (NTSC)(25pps PAL).

The bottom right corner of the menu contains a record duration calculator. The top line indicates the estimated recording time of the cameras in Event record mode only. The bottom line indicates the estimated recording time, taking into consideration the amount of time the unit will spend in Time-lapse, Activity, Event, and/or Alarm record mode.

Event Record Rate

Camera 1 : Camera 2 : 0.29 pps 3.5 spp Camera 3 : 0.34 pps 2.9 spp Camera 4 : 0.57 pps 1.8 spp : : : Camera 15 : 0.40 pps 2.5 spp Camera 16 : 0.40 pps 2.5 spp

0.40 pps 2.5 spp

[CANCEL] [OK]

% Time: 4%

125 days 8 h (EVENT) 10 days 7 h (Total)

expect to have about 20 total

of the time will be (1 hour/24 hours)

4%.

1. Rotate the Jog to navigate, and the Shuttle to change the values.

2. To save changes and exit the menu: Select [OK], and then press the Enter button.

3. To exit the menu without making changes: Press the Menu button, or select [CANCEL], then press the Enter button.

q Main Menu → Record → Activity Record Rate

The unit will record at the Activity Record Rate when the camera is in normal Timelapse Record Mode and activity is detected in the camera scene. Activity should not be linked to Event, in which case the Event Record Rate will be used.

Record rates are measured in both Pictures Per Second (pps) and Seconds Per Picture (spp).

0150-0193C 34 Calibur DVMRe Triplex

The maximum record rate per camera is inversely proportional to the number of cameras connected to

total periods of activity each day,

each lasting 3 minutes on average,

The bottom right corner of the menu contains a record duration calculator. The top line indicates the estimated recording time of the cameras in Activity record mode only. The bottom line indicates the estimated recording time, taking into consideration the amount of time the unit will spend in Time-lapse, Activity, Event, and/or Alarm record mode.

Activity Record Rate

Camera 1 : Camera 2 : 0.29 pps 3.5 spp Camera 3 : 0.34 pps 2.9 spp Camera 4 : 0.57 pps 1.8 spp :

0.40 pps 2.5 spp

% Time: 4%

Estimate of the % of time each camera will typically spend in periods of activity. For example if you expect to have about 20

then the % of the time will be 4%. (1 hour/24 hours)

: : Camera 15 : 0.40 pps 2.5 spp Camera 16 : 0.40 pps 2.5 spp

68 days 11 h (ACTIVITY)

[CANCEL] [OK]

9 days 16 h (Total)

1. Rotate the Jog to navigate, and the Shuttle to change the values.

2. To save changes and exit the menu: Select [OK], and then press the Enter button.

3. To exit the menu without making changes: Press the Menu button, or select [CANCEL], then press the Enter button.

q Main Menu → Record → Alarm Record Rate

During an alarm, the unit records at the alarm record rate. The bottom of the menu contains a record duration calculator. The top line indicates the estimated recording time of the cameras in Alarm record mode only. The bottom line indicates the estimated recording time, taking into consideration the amount of time the unit will spend in Time-lapse, Activity, Event, and/or Alarm record mode.

The configuration of the Alarm Record Rate is closely associated with the Alarm Record Mode. For detailed information about configuring the Alarm Record Mode, see Alarm Record mode in section 3.11.

Global Alarm Record Rate

% Time:

60 pps

40 days 20 h (Alarm) 15 days 11 h (Total)

[CANCEL] [OK]

0150-0193C 35 Calibur DVMRe Triplex

Estimate of the % of time the unit will typically spend in alarm mode. For example if you expect to have about 5 total periods of alarms each day,

then the % of the time will be 1%. (15 min/24 hours)

Record Duration Calculator

1. Rotate the Jog to navigate, and the Shuttle to change the values.

No overwrite

OFFONOFF

2. To save changes and exit the menu: Select [OK], and then press the Enter button.

3. To exit the menu without making changes: Press the Menu button, or select [CANCEL], then press the Enter button.

q Main Menu → Record → Record Mode

Use this menu to specify how the unit will handle data overwrite issues once the hard disk becomes full.

No Overwrite:

• Recording starts at the end of the last recording.

• Recording stops when disk becomes full.

• When the hard disk becomes full, the unit displays an on-screen message indicating that the

device is full and that the archive device has stopped recording. The user must acknowledge the message by pressing the Enter button.

Write once

Continuous

Write Once:

• Recording starts at the end of the last recording.

• Recording stops when disk becomes full.

• The user is prompted to authorize overwriting old data.

Continuous:

• Recording starts at the end of the last recording.

• Unit overwrites all previously recorded data, overwriting the oldest data first.

• The unit does not stop recording when disk becomes full.

q Main Menu → Record → Disk Maintenance

Use the Jog to select from the following options, then press the

Enter button to begin. Delete: Delete all data from the hard disk (with the possibility of restoring it). Undelete: Restore data that has been deleted, but not yet overwritten. Destroy: Erase all data from the hard disk permanently, without the possibility

of restoring it. Selecting this option brings up a confirmation dialog box.

q Main Menu → Record → Record Lock

Use this menu to set the Record Lock feature. This feature disables the front panel record button. Setting Record Lock to ON will start the unit recording if it is not currently in the Record mode.

Delete

UnDelete Destroy

ADM (Auto Delete Mode)

The ADM feature prevents the unit from displaying or archiving any search results that are more than thirty days old. This feature may be required by law in some jurisdictions. If required by local authorities, the ADM feature must be turned On. Typically this feature is turned Off.

0150-0193C 36 Calibur DVMRe Triplex

3.11 Alarms

Alarm Action

Relay Configuration

Input Configuration

Use this menu to configure the alarm handling features of the unit.

Caution! The DVMRe Triplex’s primary function is to furnish video multiplexing and recording with a multiscreen display. Although the unit has alarm handling and motion detection functions, these are considered secondary features. This unit should not be the only alarm device on site.

q Main Menu → Alarms → Input Configuration

Configure the alarm inputs as either Normally Open or Normally Closed. Configure inputs as follows. Normally Open Zero Potential Relay Contact: Configure in menu as

Normally Open. Normally Closed Zero Potential Relay Contact: Configure in menu

as Normally Closed

TTL Active High: Configure in menu as Normally Closed.

Alarm Latch

Alarm Record Mode Enable / Disable Alarm History Link to a Macro Fullscreen Alarm

Buzzer Setup Videoloss Action Pre Alarm Duration Notification Archive Alarms

TTL Active Low: Configure in menu as Normally Open. Open Collector Active On: Configure in menu as Normally Open. Open Collector Active Off: Configure in menu as Normally Closed.

q Main Menu → Alarms → Alarm Latch

This feature determines how the unit latches alarm conditions. Selecting from the following options. Latched: The alarm is activated until it is silenced and acknowledged

by the user. Transparent: The alarm is active only while receiving alarm input.

The alarm condition is canceled when the alarm input ceases. Timed Out: The alarm condition is latched for the amount of time selected in this menu, then it is

automatically silenced and acknowledged. If the alarm input exceeds the duration specified in this menu, the unit silences and acknowledges the alarm when the alarm input ceases. Select the timeout duration, the range is from 1 to 250 seconds.

Transparent alarms cannot be silenced and acknowledged. If transparent mode is preferred, but the ability to silence and acknowledge alarms is desired, select Timed Out and set the Alarm Timeout to two seconds.

Latched

Transparent Timed Out

0150-0193C 37 Calibur DVMRe Triplex

q Main Menu → Alarms → Alarm Action

Alarm Action Setup

This menu is not available on 4-channel units. Only the full screen alarm display is available on the 4-channel unit. Therefore, a 4 channel unit will always be limited to the default values in this menu, i.e. no presets linked to alarms and alarm relay is always Relay 1.

Input: Select the input you wish to configure. Freeze: Selecting Yes will freeze the alarm camera display (quadrant 1)

at the time the alarm is activated. Cameras: This setting determines the four cameras displayed on-screen

when an alarm is received. The camera group contains the camera in alarm and three associated cameras.

Default Settings: The first camera in the list is the camera in alarm. The second camera in the list is the camera that precedes the alarm camera numerically. The third and fourth cameras in the list are the two cameras following the alarm camera numerically.

Preset: Use this feature to send a camera to a preset when an alarm is activated. The preset number corresponds directly with the camera number located directly above it in this menu. Select from 1 through 16. If this field is left blank, the camera will not respond. In the example above, Camera 1 will go to Preset 1, while Camera 2 will go to Preset 9.

Relay: Configure which relay will be triggered when an alarm is activated per camera. Select from:

Input : Freeze : Yes Cameras: 01 16 02 03 Presets: 01 -- 09 -Relay : 1

[CANCEL] [OK]

• 1

• 2

• 1 + 2

• None

Rotate the Jog to navigate and the Shuttle to change the values.

q Main Menu → Alarms → Alarm Record Mode

Alarm Record Mode

Use this menu to determine how the unit will record cameras in alarm. No Change: Unit changes to the Alarm Record Rate, but it does not

give priority to the camera in alarm.

Select Mode

Interleaved

Exclusive: The unit records only the camera (or cameras) in alarm. Interleaved: Alarmed cameras are recorded at a higher rate than

non-alarm cameras. The unit accomplishes this by interleaving images of alarmed cameras between images from non-alarmed cameras in the record list. Interleaved is the

recommended mode of operation. Example of Record Lists:

No Change record list for 8 cameras, Camera-4 in alarm. 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 Exclusive record list for 8 cameras, Camera-4 in alarm. 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 Interleaved record list for 8 cameras, Camera-4 in alarm. 1 4 2 4 3 4 5 4 6 4 7 4 8 4 1 4

q Main Menu → Alarms → Enable / Disable

Use this menu to Enable or Disable the alarm inputs. Select from the following:

0150-0193C 38 Calibur DVMRe Triplex

Individual Enable

Enable All Disable All

• Individual Enable: Allow the user to access the Alarm

Fullscreen Alarm

Enable submenu, and enable or disable alarm inputs on a per camera basis.

• Enable All

• Disable All

Rotate the Jog to navigate, and the Shuttle to change the values.

Save changes and exit the menu: Select [OK], then press the Enter button.

Exit the menu without making changes: Press the Menu button, or select [CANCEL], then press the Enter button.

q Main Menu → Alarms → Alarm History

Use this window to view a list of the 100 most recent alarms. Alarms are displayed 10 at a time. Rotate the Jog to scroll through the alarms.

Information displayed in this window is:

• The alarms number in the list.

• The date of the alarm (month and day).

• The time of the alarm (hours, minutes, and seconds).

The number of the camera input in alarm.

Alarm History Box

001- 02/04 18:40:32 16 002- 02/15 12:00:10 11 003- 02/28 10:10:20 08 : : 010- 03/15 05:12:16 04

[OK]

q Main Menu → Alarms → Link To A Macro

Use this menu to link an alarm input to a macro. If a link is created, a macro will run each time that alarm is activated.

Alarm: Select the alarm input you would like to link.

Macro: Select the macro number you wish to link to. Leave this

setting blank if you do not wish to link to a macro. Rotate the Jog to navigate, and the Shuttle to change

the values.

Save changes and exit the menu: Select [OK], then press the Enter button.

Exit the menu without making changes: Press the Menu button, or select [CANCEL], then press the Enter button.

q Main Menu → Alarms → Fullscreen Alarm

Selecting Yes from this menu will cause the unit to always display the alarm camera fullscreen.

Selecting No from this menu will cause the unit to display the 4-way display configured in the Main Menu → Alarms → Alarm Action Setup menu.

Fullscreen

This menu selection is not available on 4-channel DVMRe Triplex units, since Fullscreen Alarm Mode is the only alarm mode available.

0150-0193C 39 Calibur DVMRe Triplex

Buzzer Setup

[CANCEL] [OK]

Videoloss Action

Relay 1: Disable

Buzzer : Enable

Pre Alarm Duration

TCP/IP Dialout

q Main Menu → Alarms → Relay Configuration

Use this menu to configure each relay output as either:

• Normally Open

• Normally Closed

q Main Menu → Alarms → Buzzer Setup

Use this menu to configure the internal buzzer. Global Buzzer: The Global Buzzer setting acts as a master On/Off

switch. Setting the Global Buzzer to OFF deactivates all buzzer activity.

Live Alarm Buzzer: Activates while receiving alarm input. Videoloss Buzzer: Activates when video loss is detected.

Disabling the Videoloss buzzer disables all videoloss buzzer activity. Videoloss buzzers may be disabled on a per camera basis in the

Alarms → Videoloss Action menu. Playback Buzzer: Activates during playback of recorded alarms.

q Main Menu → Alarms → Videoloss Action

Use this menu to configure how the unit responds to videoloss.

Relay Configuration

Relay 01: Relay 02: N/CLOSED

[CANCEL] [OK]

Global Buzzer : Live Alarm Buzzer: ON Videoloss Buzzer : ON Playback Buzzer : ON

N/OPEN

Camera: Select the camera you wish to configure. Relay 1: If enabled, the unit will activate Relay 1 when videoloss

is detected. Relay 2: If enabled, the unit will activate Relay 2 when videoloss is

detected. Buzzer: Use this setting to disable the videoloss buzzer activation

on a per camera basis. To disable videoloss buzzer activation on all cameras go to the Main Menu → Alarms → Buzzer Setup menu, described in the previous section.

q Main Menu → Alarms → Pre Alarm Duration

During recording, the unit stores up to 5 seconds of recorded information in a buffer. This data can be automatically retrieved when an alarm is activated. Select the amount of time just previous to the activation of an alarm you wish to retrieve.

q Main Menu → Alarms → Notification

Use this menu to select:

• Email Alarm Notification.

Camera :

Relay 2: Enable

[CANCEL] [OK]

(Time in Seconds)

0150-0193C 40 Calibur DVMRe Triplex

• TCP/IP Dialout Notification.

Email Notification Setup

Timezone Delta:

This screen allows the user to setup the types of events to be notified of, and the email addresses (up to two) to be notified. Follow the context sensitive on-screen instructions to setup the individual fields.

Email Notification Setup

One or more of these

fields must be set to

ENABLE to receive an

email notification of

the selected event.

Obtain the parameters

for these two fields from

your IT Department.

Notify Vidloss: Notify Alarm: Notify Record: Notify Archive: Email User 1: Email Domain 1: Email User 2: Email Domain 2: SMTP Server: SMTP Port:

Format of email address: user@domain The timezone delta is relative to Universal Time (UT/GMT)

ENABLE

DISABLE DISABLE DISABLE john.doe somecompany.com jane.doe somecompany.com

0. 0. 0. 0 25

-07 [CANCEL] [OK]

Email Address Format

The format of the email addresses should be entered as follows. If the email address to be notified is

john.doe@somecompany.com, then john.doe should be entered in one of the Email User fields and

somecompany.com should be entered in the subsequent Email Domain field.

Timezone Delta

The timezone delta integer is based on how many time zones your current time zone is from Greenwich Mean Time (GMT). To calculate your timezone delta use the following formula.

Current time – Greenwich Mean Time = Timezone Delta For example: If the current time is 0900 hours, and the GMT is 1600 hours, then the timezone delta

would be –0700 and should be expressed in the field as –07.

To obtain the GMT open an Internet Browser on an Internet connected PC and point the browser to

www.greenwichmeantime.com.

TCP/IP Dialout Notification Setup

This screen allows the user to setup the types of events to be notified of, and the IP addresses (up to two) of the PC(s) where the WaveReader software resides.

WaveReader must be running on the receiving PC(s) and Alarm Monitoring must be setup. See Alarm Monitoring in the WaveReader Manual for details.

0150-0193C 41 Calibur DVMRe Triplex

TCP/IP Dialout Notification Setup

Macro Record

Select Macro

One or more of these

fields must be set to

ENABLE to receive an

email notification of

the selected event.

The IP Addresses

of the PC on which

the WaveReader

Software resides

Notify Vidloss: Notify Alarm: Notify Record: Notify Archive: Notify Menu Access: Notify Power Up: Notify Connection: Primary Host: Backup Host: Port: Notification Interval (minutes):

[CANCEL] [OK]

DISABLE

DISABLE DISABLE DISABLE DISABLE DISABLE DISABLE

0. 0. 0. 0

0. 0. 0. 0 27

10 Immediate

The Notification Interval can be set from 1 minute to 60 minutes, or immediately upon the event.

q Main Menu → Alarms → Archive Alarms

Selecting Enable from this menu will cause the unit to activate Relay 2 if a malfunction occurs while archiving.

Archive Alarm

Relay 2

ENABLE

3.12 Macro

A macro is a recorded sequence of keystrokes. The number of macros depends on the number of camera inputs (4, 10 or 16). Each macro can have up to 32 keystrokes.

Use this menu to:

• Enter Macro Record mode.

• Program a scheduled start time for a macro.

• Edit the RS232 command string for each submacro.

q Main Menu → Macro → Macro Record

Note: Do not attempt macro programming while the front panel is locked.

To begin recording a macro:

1. Select the macro number you wish to record, then press the Enter button. The unit will automatically exit the menu system and go to a starting point. Macro Record mode is indicated as F and the Macro Number on-screen.

Macro Record

Timed Macro Start Edit Submacro

2. From this point, begin recording the desired keystroke sequence. Record up to 32 keystrokes. If 32 keystrokes are exceeded, the unit will end the macro recording automatically.

0150-0193C 42 Calibur DVMRe Triplex

3. When finished programming, press the Function button then the Enter button to end the macro recording. A form is provided in section 9 to keep track of recorded macro functions.

Keystroke count while in the menu system: While recording a macro, entering the

NOTE

During macro recording, the following button combinations perform special functions.

Button Sequence Resulting Action

menu system, changing multiple menu items, and exiting the menu system are only counted as one keystroke. Using the Jog to navigate the menu system does not count as keystrokes. Once the menu system has been exited, re-entering the menu system will count as a second keystroke.

Not all menu items can be programmed using macros. For a complete list of macro programmable menu items, see the table below.

Function then 1. Function then 2. Function then 3. Function then 4. Function then 5. Function then 6. Function, Function, then

Submacro number. Function then Enter.

Activate Relay 1 output. Reset Relay 1 output. Pause macro for 1 second. Pause macro for 5 seconds. Activate Relay 2 output. Reset Relay 2 output. Program a specific submacro to activate when the macro is run.

End macro recording

Macro Excluded Features

The following core features or settings cannot be programmed by Macro.

• Disk Maintenance.

• Erase Archive Medi um.

• POTS Setting.

• Ethernet Setting.

• RS485 Network Address.

• Front Panel Lock/Unlock.

• Record Timer.

q Main Menu → Macro → Timed Macro Start

Use this menu to program scheduled start times for macros. Up to 20-scheduled start times can be programmed in this menu.

Event: Select the scheduled start event you wish to edit. Day: Select the start day (Monday – Sunday) of the macro.

Select ** (double asterisks) to run the macro every day. Select None to cancel the scheduled start time.

Time: Select the start time for the macro. Macro: Select the desired macro number.

0150-0193C 43 Calibur DVMRe Triplex

Timed Macro Setup

Event : Day : Monday Time : 00:00 Macro : 01

[CANCEL] [OK]

A form is provided in section 9 to keep track of scheduled macros.

Setup Parameters

Setup Active Zones

Indicate Detection

q Main Menu → Macro → Edit Submacro

A submacro is an RS232 command string used to control a peripheral device. Submacros are activated during macros. See the table on page 43 for information about programming a macro to activate a submacro.

Select the submacro you wish to edit from the menu system. This menu will appear.

Edit Submacro 01

080 066 066 010 --- --- --- --- --- ---

[P] [B] [B] [0]

[CANCEL] [OK]

ENTER key starts Submacro edit

Use this menu to create the RS232 command string. Press the Enter button to Enter and Exit the submacro edit mode. Rotate the Jog/Shuttle to navigate among the fields and change the values. Each byte value can be set from 0 to 255.

Running A Macro

A macro is a recorded sequence of up to 32 keystrokes. To activate a macro, press the Function button followed by the Number button of the desired macro. While running, the macro is indicated on-screen as the letter F and the macro number.

The user can cancel the macro at any time by pressing the Function button.

{F}

Function and

Number Buttons

Daylight Savings Time

To adjust the time one hour for daylight savings time, press the Function button, then the Sequence button. If this function is activated during April, one hour is added to the time. If this function is activated in October, one hour is subtracted from the time. This function will only operate once per time period.

{F}

Function and

Sequence Buttons

3.13 Motion Detection

Use this menu to:

• Enable motion detection on a per camera basis.

• Activate individual zones in a scene to respond to motion

detection.

• Activate the on-screen motion detection indicator.

• Set motion detection as Activity detection or Intrusion Detection.

• Configure the motion detection parameters on a per camera basis.

Enable/Disable Detection

0150-0193C 44 Calibur DVMRe Triplex

Detection Enable

Camera 02: Disable

q Main Menu → Motion Detection → Enable/Disable Detection

Selecting Enable All or Disable All from this menu will activate or deactivate motion detection on all cameras.

Selecting Individual Enable from this menu will bring up the following menu.

Individual Enable

Enable All Disable All

Individual Enable Menu

Use this menu to enable or disable motion detection on a per camera basis. Rotate the Jog to navigate, and the Shuttle

Camera 01:

Enable

to change the values.

Camera 03: Enable : : Camera 16: Enable

[CANCEL] [OK]

q Main Menu → Motion Detection → Setup Parameters

Use this menu to select the Camera, Motion Detection Type, and Sensitivity of the Motion Detection you wish to configure.

Motion Detection Parameters Setup

Camera Motion Detection Type Sensitivity Relay Output Link to Event

Rejection Target Size Link to Alarm

ACTIVITY 06 2

---

LOW 01 NONE

[CANCEL] [OK]

Navigate in this menu using the Jog to select the field and the Shuttle to change the parameters.

Activity Vs. Intrusion

Activity Detection is a simple type of motion detection having only a sensitivity setting and a relay output. Intrusion Detection is a more sophisticated type of motion detection, with additional features such as false alarm rejection levels, minimum target size, and an alarm output.

0150-0193C 45 Calibur DVMRe Triplex

Activity Detection Setup

If Activity is selected in Motion Detection Type field, the following parameters are enabled: Relay Output: The unit may be configured to activate a relay output when motion detection is

present. Select either 1, 2, 1+2 (both relays), or None. Link to Event: Selecting Yes in this menu will activate the event record speed when activity detection

is present.

Intrusion Detection Setup

If Intrusion is selected in Motion Detection Type field, the following parameters are enabled: Sensitivity: Rotate the Shuttle to change the motion detection sensitivity, 10 being the most

sensitive. Rejection: Configure the unit’s false alarm rejection feature by selecting Low, Medium, or High.

These settings are based on the number of simultaneously triggered zones and the persistence of motion in a scene. The Low setting is the most sensitive to motion. The Medium setting will filter out most false alarm situations due to sudden luminance changes over the whole scene (clouds passing over). The High setting will filter out sudden luminance changes as well as spurious motion events that do not persist for a number of frames (a bird flying past the lens).

Target Size: This setting is the minimum number of zones (from the 16 x 16 grid) that must be activated simultaneously before it is considered to be valid motion.

Link To Alarm: Select the alarm number that you wish to activate when motion detection is activated.

q Main Menu → Motion Detection → Setup Active Zones

Use this menu to setup the Active Zones for motion detection. The screen shown below will overlay the current video image allowing for precise activity zone setup. The disabled zones will be tinted. The enabled zones will be clear.

Activity Grid Setup Screen

0150-0193C 46 Calibur DVMRe Triplex

‘MENU’ : Exit Activity Setup

‘ENTER’: Save and Exit Activity Setup

‘PAUSE’: Toggle between Enable and Neutral

‘STOP’ : Toggle between Disable and Neutral

‘PLAY FORWARD’: Increase the Sensitivity level

“PLAY REVERSE’: Decrease the Sensitivity level

Play Forward to increase the Sensitivity

Indicate Detection

Titles Display

Camera Disable

Pressing the Function button will bring up the Help screen shown on the next page. This screen will overlay the current video image.

{F}

Function

‘ZOOM’ : Disable/Enable all zones

Button

Sensitivity Scope

Use the sensitivity scope to adjust the motion detection sensitivity for the scene. The sensitivity scope is the bar located near the left-hand corner of the screen.

The black bar raises and lowers to indicate the degree of motion detected. When the black bar reaches the red bar, a motion detection alarm is activated.

Adjusting Motion Detection Sensitivity: Raise and lower the red bar to change the motion detection sensitivity. Use the Play Forward button to increase the sensitivity level and the Play Reverse button to decrease the sensitivity level. The sensitivity level is also displayed as a numeric value.

Play Reverse to decrease the Sensitivity

q Main Menu → Motion Detection → Indicate Detection

Motion Detection may be indicated on-screen by displaying the letter M. Use this menu to turn this feature On or Off.

Detection

3.14 Camera Setup

Use this menu to:

• Edit the title for each camera.

• Adjust the Automatic Gain Control.

• Disable or Enable camera inputs.

• Specify cameras as covert (recorded but not displayed).

• View the Camera Scope (Histogram)

q Main Menu → Camera Setup → Camera Titles

Use this menu to:

• Specify if the camera titles will be displayed on the monitors. Edit the title for each camera.

0150-0193C 47 Calibur DVMRe Triplex

Camera Titles Camera AGC

Covert Camera Camera Scope

Edit Titles

Titles Display

[CANCEL] [OK]

Monitor B: OFF

Camera titles may be displayed on either monitor. Use this menu to turn this feature On or Off.

Rotate the Jog buttons to navigate and the Shuttle to change the values.

Monitor A:

Edit Titles

Rotate the Shuttle to select the camera whose title you wish to configure, and then press the Enter button. The Camera Title Edit menu will appear.

Camera Title Edit

Camera Title : Camera 01

@ABCDEFGHIJKLMNOPQRSTUVXXYZ[\]^

SEQ key selects character bank ‘1’ key inserts blank character ‘2’ key inserts selected character

[CANCEL] [OK]

Camera Title Edit Menu

1. With the camera title selected, press the Enter button. The menu will enter the Edit mode and the

character bank will appear in the center of the menu.

2. Press the Sequence button to select the desired character set.

3. Rotate the Shuttle to navigate the cursor in the camera title.

4. Rotate the Jog to navigate the cursor in the character bank.

5. Press the Number 1 button to insert a blank character or press the Number 2 button to insert the

selected character.

6. When finished editing the title, press the Enter button to exit the edit mode.

7. Save changes and exit the menu: Select [OK], then press the Enter button.

8. Exit the menu without making changes: Press the Menu button, or select [CANCEL], then press

the Enter button.

q Main Menu → Camera Setup → AGC

Use the Automatic Gain Control (AGC) to adjust the video input signal level for cameras whose level is outside the normal range. The default gain setting is 100%.

Rotate the Jog to navigate and the Shuttle to change the values.

Save changes and exit the menu: Select [OK], then press the Enter button.

Exit the menu without making changes: Press the Menu button,

or select [CANCEL], then press the Enter button.

0150-0193C 48 Calibur DVMRe Triplex

Signal Gain Setup

Camera 01 Signal Gain 100%

[CANCEL] [OK]

Power Up Disable

Auto Disable Now

Individual Disable

Camera Disable

[CANCEL] [OK]

Camera 03: Disable

Power Up Disable

[CANCEL] [OK]

Camera 02: YES

q Main Menu → Camera Setup → Camera Disable

Use this menu to:

• Enable or Disable cameras individually

• Configure the unit to disable cameras automatically at power-up

if video loss is detected.

• Automatically disable all inputs detecting videoloss.

Individual Disable

Use this menu to Disable or Enable each camera input

Camera 01: Camera 02: Enable

Disable

individually. Use the Jog to navigate and the Shuttle to change the values. Save changes and exit the menu: Select [OK], then press

the Enter button. Exit the menu without making changes: Press the Menu

Camera 04: Enable : : Camera 16: Enable

button, or select [CANCEL], then press the Enter button.

Power Up Disable

With this feature turned On (Enabled), the unit will automatically detect which inputs are experiencing videoloss at power-up, and disable them.

Disable

Rotate the Jog to navigate and the Shuttle to change the values.

OFF

Auto Disable Now

This feature detects which inputs have video signals and which are experiencing videoloss. When this feature is activated, the unit will automatically disable the inputs experiencing videoloss. The DVMRe Triplex will also re-enable video inputs that were previously disabled if a video input signal is detected.

q Main Menu → Camera Setup → Covert Camera

This feature removes cameras from all live displays while continuing to record them, so that the users and the public are unaware that the camera is being recorded. Covert cameras are viewable during playback.

Select Yes in this menu to configure a camera as covert. Rotate the Jog to navigate and Shuttle to change the values.

0150-0193C 49 Calibur DVMRe Triplex

Covert Camera

Camera 01:

Camera 03: NO Camera 04: NO : : Camera 16: NO

q Main Menu → Camera Setup → Camera Scope

Luminance Histogram

Luminance

OFF

Use this menu to view a live luminance histogram of the currently displayed camera.

Luminance Histogram

A Luminance Histogram is a graphical representation of how many times each gray-level value occurs in an image.

Use this feature to analyze and optimize the video input signal.

Black

White

3.15 Archive Setup

Data recorded by the unit can be archive to an external archive device.

Use this menu to:

• Turn Background Archiving mode Off and On.

• Erase the recorded data on a compatible archive device.

q Main Menu → Archive Setup → Background Archive

Background Archive: Commands the unit to record data to both the

hard disk and the archive device simultaneously. Select from the following items.

OFF: Turns background archiving Off. ON: Turns background archiving On.

Background Archive

Erase Archive Medium

0150-0193C 50 Calibur DVMRe Triplex

q Main Menu → Archive Setup → Erase Archive Medium

RS485

POTS Setup

G.711

Use this feature to erase all of the recorded data on an archive device.

With Erase Archive Medium highlighted, press the Enter

Erase all Records. Are you sure?

button. If a compatible archive device is connected, a confirmation box will appear, otherwise no action will occur.

3.16 Audio Setup

Use this menu to enable or disable the audio feature of the Triplex. Select from:

• OFF

• G.711

3.17 Communications

Use this menu to:

• Configure the baud rates and settings for the RS232 ports.

• Configure the network address for the RS485 network.

• Configure the Ethernet address and networks settings.

Message

YES

OFF

RS232

Ethernet

q Main Menu → Communications → RS232

Select the Port you wish to configure and press the ENTER button.

Port 1

Port 2

Port 1

Use this menu to:

• Enable/Disable POTS and configure the Modem initialization string (POTS Setup).

Baud Rate

• Adjust the Baud rate.

POTS Setup

The default modem string (shown below) is for use with Hayes Accura 56k, Diamond Supra Express 56k, and 5686 US Robotics modems in their default conditions. Consult with the modem manual before attempting to make any changes. It is strongly recommended that the modem initialization string only be modified by a qualified technician.

0150-0193C 51 Calibur DVMRe Triplex

POTS Setup

POTS : DISABLE

1200 Baud

2400 Baud

4800 Baud

19200 Baud

38400 Baud

57600 Baud

Modem Init String : AT&F1&K3M0E1Q0V1S0=0&R2&C1&D0&H1

[Default Modem String] [CANCEL] [OK]

@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^

SEQ key selects character bank ‘1’ key inserts blank character ‘2’ key inserts selected character

1. With the Modem Init String highlighted, press the Enter button to enter the Edit mode. The character bank will appear in the center of the menu.

2. Press the Sequence button to select the desired character bank.

3. Rotate the Shuttle to navigate the Modem Init String.

4. Rotate the Jog to select a character from the character bank.

5. Use the Number 2 button or rotate the Shuttle to insert the desired character from the character

bank into the Modem Init String and advance to the next character.

6. Use the Number 1 button to insert a blank character.

7. When finished, press the Enter button.

8. To save the changes and reboot, select OK, then press the Enter button. The unit will only reboot

if changes were made to the Modem Init String.

9. To exit the menu without making changes, select Cancel, then press the Enter button. Pressing the Menu button also exits the menu without making changes.

Baud Rate

Use this menu to configure the baud rate for Port 1. Rotate the Jog to select a baud rate from the menu.

Save changes and exit the menu: Press the Enter button. Exit the menu without making changes: Press the Menu button.

9600 Baud

Port 2

The RS232 port 2 is used for Event Generation and ASCII Text Insertion. See Section 7 for the RS232 Protocol required to perform these functions.

0150-0193C 52 Calibur DVMRe Triplex

q Main Menu → Communications → RS485

Connect several units to a single keyboard, or vice-versa. Up to 32 units (any combination of multiplexers and keyboards) can be networked together. Use this menu to specify the units unique network address.

Save changes and exit the menu: Press the Enter button. Exit the menu without making changes: Press the Menu button.

Network Address

q Main Menu → Communications → Ethernet Settings

An ethernet connection can be used to connect to the unit from a PC for viewing of live or recorded images. Use this menu to configure the Ethernet communications settings. Select from the following:

Ethernet: Select Enable or Disable. IP Address / Subnet Mask / Gateway: Consult with a qualified

Network Administrator or an MIS professional to configure these settings.

3.18 Front Panel Lock

Use this feature to lock the front panel keypad. While locked, the only operational key on the front panel is the Menu button. To unlock the front panel, enter the Installer password and return to this menu.

Highlight the item you wish to select.

Save changes and exit the menu: Press the Enter button. Exit the menu without making changes: Press the Menu button.

3.19 Factory Settings

Ethernet Settings

Ethernet : IP Address : 10. 90.253. 22 Subnet Mask: 255.255. 0. 0 Gateway : 10. 90. 0. 1

Unlock Keyboard

Lock Keyboard

Enable

[CANCEL] [OK]

Return To Factory Defaults

From the Factory Setting menu, press the Enter button. A password box will appear. Enter the Factory Default password. Select OK, then press the Enter button.

The unit will reboot, returning all settings (except the time and date) to the factory defaults. Due to the large size of the hard disk, the reboot may take several minutes.

Factory Default Password

10 and 16-Channel 4-Channel

8 1 1 1

4 1 1 1

Change Language

From the Factory Setting menu, press the Enter button. A password box will appear. Enter the Language password. Select OK, then press the Enter button.

A menu will appear displaying the available language selections. Rotate the Jog to select the desired language.

Save changes and exit the menu: Press the Enter button. Exit the menu without making changes: Press the Menu button.

0150-0193C 53 Calibur DVMRe Triplex

Language Password

10 and 16-Channel 4-Channel

5 4 1 5

1 4 1 4

Installer Password

Edit Camera Titles

Installer Password

3.20 Passwords

Use this feature to change the Installer, Operator or Ethernet passwords.

Changing the Installer or Operator Passwords

To change the password:

1. Highlight the password you wish to change, then press the Enter button. A password box will appear.

2. Enter the new password using the Number buttons.

3. Highlight OK, then press the Enter button.

4. Re-enter the password.

5. Highlight OK, then press the Enter button. The user will be

prompted, indicating if the password was entered correctly and changed.

The Ethernet Password

The Ethernet Password feature limits access to only those users who access the unit using the password feature of WaveReader versions 2.3 or later. When the unit is first setup, the default is No Password Protection. Meaning, anyone using WaveReader and accessing with an ethernet connection can connect to the unit.

Operator Password Ethernet Password

Password Box

Enter a new Install Password

---

Password Box

Enter a new Ethernet Password

---

Activate The Ethernet Password

1. Enter the new password using the Number buttons.

2. Highlight OK, then press the Enter button.

3. Re-enter the password.

4. Highlight OK, then press the Enter button. The user will be prompted, indicating if the password was

entered correctly and changed.

Deactivate The Ethernet Password

To return the unit to No Ethernet Password Protection, enter the Ethernet Access Reset Password in the password box shown above.

Ethernet Access Reset Password

1 1 1 1

3.21 The QuickInstall Menu

QuickInstall Menu Overview

After installation is complete, it is strongly recommended that, as a minimum, the items in the QuickInstall menu be configured before the unit is used.

All items located in the QuickInstall menu are also found in the Main menu. These items are provided in the separate QuickInstall menu as a convenience for the installer.

Change the time Change the date

Camera Disable Record Quality

Auto Disable Now

0150-0193C 54 Calibur DVMRe Triplex

Use the following table to find detailed information about configuring

Sequencing

specific items from the QuickInstall menu.

QuickInstall Menu Item

Change the time Change the date Edit Camera Titles Camera Disable Record Quality Installer Password Auto Disable Now

Main Menu → Time/Date → Set Time Main Menu → Time/Date → Set Date Main Menu → Camera Setup → Camera Titles Main Menu → Camera Setup → Camera Disable Main Menu → Record → Record Quality Main Menu → Passwords → Installer Password Main Menu → Camera Setup → Camera Disable

→ Auto Disable Now

Primary Menu Location

3.22 The Operator Menu

The Operator Menu Overview

The Operator menu is provided so that the user has access to a limited number of menu items. These menu items are primarily monitor display setup options, so that the user may “personalize” the monitor displays during their shifts. Other options include video archive setup and changing the operator password.

None of the items are unique to the Operator menu. All items located in the Operator menu are also found in the Main menu.

Section In

Manual

3.8

3.14

3.10

3.20

3.14

Time/Date Display Titles Display Alarm History Archive Setup Operator Password

Use the following table to find detailed information about configuring specific items from the Operator menu.

Operator Menu Item Primary Menu Location

Sequencing Time/Date Display Titles Display

Alarm History Video Archive Setup Operator Password

Main Menu → Sequencing Main Menu → Time/Date → Time/Date Display Main Menu → Camera Setup → Camera Titles →

Title Display Main Menu → Alarm → Alarm History Main Menu → Archive Setup Main Menu → Password → Operator Password

Section In

Manual

3.9

3.8

3.14

3.11

3.15

3.20

0150-0193C 55 Calibur DVMRe Triplex

About DVMR

3.23 The SystemView Menu

The SystemView Menu Overview

The SystemView menu is provided so that users may quickly view global software and hardware settings.

View Screen 1 View Screen 2 View Screen 3 View Screen 4 View Screen 5 View Screen 6 View Screen 7 View Screen 8

About DVMRe menu: This menu provides information such as model designation, serial number, software version, software date, boot code version hard disk size, IP address, and hardware address (MAC).

Model: Serial Number: Software Version: Software Date: Boot Code Version: Disk Size: IP Address: Hardware Address:

DVMRe-16CT D406-T72-210001 VER 4.08 Oct 15 16:40:18 2002 VER 1.03

163.93 GB

3.18.173.10 BA-BE-C6-7E-FA-CE

View Screens 1 through 8: These menus provide an overview of the units current operating parameters and the menu settings selected by the user or installer. Each View Screen is described in the following tables.

The View Screens

View Screen 1

Alarm Input

• Enable/Disable: 1 = Enabled, 0 = Disabled

• Normally Open or Normally Closed: 0 = Open, C = Closed

• Macro: Macro number if activated

Alarm Action

• Freeze: 1 = Freeze, 0 = No Freeze

• Cameras: Primary camera in alarm and three associated cameras

• Relay: 1, 2, 1+2, or None

View Screen 2

Camera

• Enable/Disable: 1 = Enabled, 0 = Disabled

• Signal Gain: AGC setting from 1 through 10

• Covert Camera: Yes or No

• Camera Title

Videoloss Action

• Relay 1: 1 = Enabled, 0 = Disabled

• Relay 2: 1 = Enabled, 0 = Disabled

• Buzzer: 1 = Enabled, 0 = Disabled

0150-0193C 56 Calibur DVMRe Triplex

View Screen 3

Motion Detection

• Enable/Disable: 1 = Enabled, 0 = Disabled

• Activity or Intrusion Detection: I = Intrusion, A = Activity

• Sensitivity: 1 through 10

• Relay Output: None, 1, 2, 1+2

• Link to Event: Yes or No

• Rejection Ratio: High, Medium, or Low

• Target Size: 1 through 256

• Alarm Camera: 1 through 4, 10 or 16

View Screen 4

Record Rate

• Event Camera Settings: T = Timelapse, E = Event, ET = Event and Timelapse

• Timelapse Record Rate: In pictures per second (pps).

• Event Record Rate: In pictures per second (pps).

• Pre Event Duration: 0 to 5 seconds.

• Post Event Duration: 0 to 200 seconds.

• Acitvity Record Rate: In pictures per second (pps).

• Record Quality: High, Medium, or Low.

View Screen 5

Record Timer

• DAY: 1-31, Mon, Tue, Wed, Thu, Fri, Sat, Sun, Mon-Fri, Sat-Sun, Mon-Sun

• Start: Time (HH:MM)

• Stop: Time (HH:MM)

• Macro: Macro Number, On or Off

View Screen 6

• Time and Date Display A: On or Off.

• Time and Date Display B: On or Off.

• Time Format

• Date Format

• Titles Display A: On or Off.

• Titles Display B: On or Off.

• Master Clock: Yes or No.

• Multiscreen Dwell: In seconds.

• Full Screen Dwell: In seconds.

• Record Mode: No Overwrite, Write Once, or Continuous.

• Auto Disable: On or Off.

• Indicate Detection: On or Off.

0150-0193C 57 Calibur DVMRe Triplex

View Screen 7

• Global Buzzer: On or Off.

• Live Alarm Buzzer: On or Off.

• Video Loss Buzzer: On or Off.

• Playback Buzzer: On or Off.

• Relay 1: Normally Open or Normally Closed.

• Relay 2: Normally Open or Normally Closed.

• Alarm Latch: T = Transparent, L = Latched, TO (020) = Timed Out (Time)

• Alarm Record Mode: Interleaved, Exclusive, or No Change.

• Full Screen Alarm: Yes or No. This feature is not available on the 4-Channel units.

• Global Alarm Record Rate: In pictures per second (pps).

• Pre Alarm Duration: In seconds.

• Archive Alarm: Enable or Disable.

View Screen 8

• Background Archive: On or Off.

• Monitor Setup: Single or Dual.

• Baud Rate Port 1

• Baud Rate Port 2

• Network Address

• Ethernet: Enable or Disable.

• POTS: Enable or Disable.

• Language: English, German, or French.

• Keyboard Lock: On or Off.

• Record Lock: On or Off.

0150-0193C 58 Calibur DVMRe Triplex

4 Alarms

4.1 Alarm Input

Alarm devices are connected via the Alarm PCB on the back panel of the unit (see section 1.7). Each Alarm Input corresponds with the Camera Input of the same number. Alarm input to camera number assignments can be changed on 10 and 16-channel models. See Alarm Action menu (section 3.11).

4.2 Alarm Output

Front Panel Alarm LED: The LED located to the left and above the Alarm button is lit for the duration

of the alarm. Internal Buzzer: The internal buzzer is activated until it is Silenced and Acknowledged. This feature

can be turned off in the menu system (see Buzzer Setup in section 3.11).

Monitor Displays: Discussed below in the On-screen Displays During Alarms section. Output Relays: The alarm output relays are active for the duration of the alarm. This feature is

configured in the menu system (see Alarm Action and Relay Configuration in section 3.11) and can be deactivated.

Macro Activation: Unit can be configured in the menu system to activate a macro when an alarm is detected.

Preset PTZ Camera commands: Unit can be configured in the menu system to send preset commands to specific cameras when an alarm is detected.

Record Rate: Record Rate can be increased by recording at the Alarm Record Rate (see section

3.10) and by Interleaved or Exclusive Recording (see Alarm Record mode in section 3.11).

4.3 Alarm Acknowledge

Pressing the Alarm button acknowledges to the unit that the alarm has been recognized and silences the internal buzzer. This does not clear the alarm condition.

4.4 On-screen Displays During Alarms

10 and 16-Channel Units

Monitor-A in Live Multiscreen Mode

Single Alarm: When a single alarm is received, the unit changes to 4-way

display containing the camera in alarm, and three associated cameras. The three associated cameras are defined as a group in the menu system (see Alarm Action in section 3.11). The top left cameo displays the camera in alarm.

Second Alarm: When a second alarm is received, the unit changes to a 10-way multiscreen, displaying the alarm cameras in the top two cameos. The associated cameras are displayed in the remaining cameos.

Third Alarm: When a third alarm is received, the unit changes to a 9-way multiscreen, displaying the alarm cameras in the top three cameos. The associated cameras are displayed in the remaining cameos.

More than three alarms simultaneously: The unit switches to the maximum multiscreen display, i.e. 16 or 10-way.

4-Way

Single Alarm

10-Way

Second Alarm

9-Way

Third Alarm

0150-0193C 59 Calibur DVMRe Triplex

Other display options include:

LIVE MODE

PLAYBACK MODE

Monitor A

Monitor B

• A full screen display of a single camera in alarm, with a sequenced full screen display for additional cameras in alarm. This option is selectable in the menu system (see Full Screen Alarm in section 3.11).

• Freeze camera display at the time the alarm was received.

Monitor-B Display During Alarm

Single Alarm: Unit switches to a full screen display of the camera in alarm. Additional Alarms: Unit switches to a sequenced display of all cameras in alarm.

4-Channel Units

Single Alarm: Unit switches to a full screen display of the camera in alarm. Additional Alarms: Unit switches to a sequenced display of all cameras in alarm.

4.5 Alarm Operations During Playback

Live Alarms Displays

Single Alarm: Unit switches to a full screen display of the camera in alarm on Monitor B. Additional Alarms: Unit switches to a sequenced display of all cameras in alarm on Monitor B.

LIVE

LIVE ALARM

LIVE

LIVE ALARM

FULL

SCREEN

ALARM

PLAY

BACK

LIVE ALARM

PLAY

BACK

LIVE

LIVE ALARM

FULL

SCREEN

ALARM

0150-0193C 60 Calibur DVMRe Triplex

Recorded Alarms

Internal Buzzer: During playback, the internal buzzer is activated until it is silenced and

acknowledged. This feature can be turned off in the menu system (see Playback Buzzer, Buzzer Setup in section 3.11).

Front Panel Alarm LED: The LED located to the left and above the Alarm button is lit for the duration of the alarm.

Monitor-A Multiscreen: Each camera in alarm is indicated on-screen by a flashing red “A” in its cameo. Alarm LED lights to indicate an alarm condition. There is no change in the playback (or Triplex) multiscreen based on playback of recorded alarms.

4.6 Alarm History Box

The Alarm History feature provides a list of the 100 most recent alarms. View the Alarm History Box by accessing the menu system, and selecting Operator → Alarm History. The Alarm History Box can also be found under Main Menu → Alarm → Alarm History. For detailed information about viewing the Alarm History Box see Alarm History in section 3.11.

4.7 Searching For Recorded Alarms

See section 5.

0150-0193C 61 Calibur DVMRe Triplex

Play Back

Search Filters

Operation: Play from Disk

DATE (MM/DD/YY) TIME (HH:MM)

Start Stop Start Stop

01/27/02 01/27/02 20:57 20:59

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

[START SEARCH]

Search Filters

Search Results

Start Date Start Time Days HH MM SS

002 01/21/2002 20:09:10 0 00:00:38

003 01/21/2002 20:10:10 0 01:07:22

004 01/22/2002 20:07:10 0 00:00:07

005 01/23/2002 20:07:10 0 00:08:56

006 01/24/2002 20:07:10 0 00:00:06

007 01/25/2002 20:07:10 0 05:57:31

008 01/26/2002 20:07:10 0 00:46:43

000 01/21/2002 20:07:10 0 04:35:15

Enter

5 Searching

The DVMRe Triplex provides a powerful search interface to access video files stored on the hard disk or an external archive device.

Search Menu Overview

Button

Disk Analysis Screen

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Alarm Event Activity Videoloss Present Absent Hit SEARCH again to enter Advanced Search Level 1

01/21/2002 20:17:01

Motion Search

Search Button

Motion Search

Last 2hrs Last 8hrs Last day Last 7 days Last 4 weeks Last 12 weeks CustomX

Activity Setup

Enter

Search Button

Activity Event Alarm Text

Camera

X X X X X X X X X X X X X X X X

[CANCEL]

Enter

Play Back

Search Results

001 01/21/2002 20:08:10 0 00:01:55

9 matches found.

‘PLAY REV/FWD’ to page up/down ‘ENTER’ to play event; ‘SEQ’ to repeatedly play event.

Enter

Button

0150-0193C 62 Calibur DVMRe Triplex

5.1 Disk Analysis Screen

Alarm Event Activity Videoloss Present Absent

Level 1

Disk Time

and Date

Arrow Cursors

Begin by pressing the Search button. The Disk Analysis Screen will appear. This screen shows a graphical representation of the recorded video stored on the internal hard disk.

02/28/2002 20:45:00

Search Button

Disk Analysis Screen

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Hit SEARCH again to enter Advanced Search Level 1

01/21/2002 20:17:01

at cursor location.

Zoom Level

Rotating the Jog moves the two arrow cursors across the representation of the recorded video. As the cursors move across the screen the corresponding disk time is indicated in the upper right of the screen. The video representations are color-coded by category. Rotating the Shuttle expands (Zooms) the display. The Lowest level (most detail) is indicated on screen with an (L). Pressing the Enter button will start Playback from the cursor location.

5.2 Motion Search

Pressing the Search button a second time will bring up the Motion Search menu. This menu performs a motion search with six preset time parameters and a custom search option. Rotate the Jog to navigate and the Shuttle to select a specific parameter. Selecting the Custom option and pressing the Enter button starts playback and brings up another window with Start/Stop, Time/Date options. These options provide the parameters to focus the search to a specific time period.

0150-0193C 63 Calibur DVMRe Triplex

Motion Search

‘MENU’ : Exit Activity Setup

‘ENTER’: Save and Exit Activity Setup

‘PAUSE’: Toggle between Enable and Neutral

‘STOP’ : Toggle between Disable and Neutral

Button

Last 2hrs Last 8hrs Last day Last 7 days Last 4 weeks Last 12 weeks

Custom

Selecting any of the other options and pressing Enter starts playback and displays the Motion Search Setup Screen.

This screen overlays the current playback video and allows the user to enable or disable motion detection on the screen within blocks that form a 16 x 16 grid.

Pressing the Function key while in this screen overlays a help screen with all the available commands.

{F}

Function

Pressing Enter upon completion of the activity setup will start the search and launch the Search Results window. See section 5.4 for operating instructions.

‘ZOOM’ : Disable/Enable all zones

0150-0193C 64 Calibur DVMRe Triplex

5.3 Search Filters

3. Copy from Disk to Archive.

4. Copy from Archive to Disk.

XXXXXXXXXXX

Pressing the Search button a third time brings up the Search Filters Menu. Use the Search Filters menu to specify:

• The type of operation to be performed: Play from Disk, Play from Archive, Copy from Disk to Archive, and Copy from Archive to Disk.

• The Start and Stop date of the search.

• The Start and Stop time of the search.

• Searching for recorded activity, events, or alarms.

• Searching for a text string.

• Which cameras to search inclusively or exclusively.

Search Filters

Operation: Play from Disk

DATE (MM/DD/YY) TIME (HH:MM) Start Stop Start Stop 01/27/02 01/27/02 20:57 20:59

Activity Event Alarm Text

Camera 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

X X X X X X X X X X X X X X X X

X X X X X

[CANCEL] [START SEARCH]

The following options are available when an archive device is connected:

1. Play from Disk.

2. Play from Archive.

Hit Camera buttons to select/deselect individual cameras. Use the Zoom button to globally select/deselect cameras to search.

Selecting Search Parameters

1. Rotating the Jog to navigate, highlight the box adjacent to the parameters that you wish to modify.

2. Once in the Parameter Box, use the Shuttle to navigate through the fields and the Jog to change

the values.

3. To activate the parameter, use the Shuttle or the Enter button to place an [X] in the check box.

4. When finished, use the Jog to navigate to another parameter.

5.4 Search Results

Activate Search

From the Search Filters menu, use the Jog to navigate to the Start Search parameter. With the Start Search parameter highlighted, press the Enter button to begin the search operation. When finished

searching, the Search Results window will appear. A maximum of 200 results can be displayed per search.

Follow the directions on-screen to select, archive, playback, etc.

0150-0193C 65 Calibur DVMRe Triplex

Search Results

Start Date Start Time Days HH MM SS

000 01/21/2002 20:07:10 0 04:35:15

001 01/21/2002 20:08:10 0 00:01:55 002 01/21/2002 20:09:10 0 00:00:38 003 01/21/2002 20:10:10 0 01:07:22 004 01/22/2002 20:07:10 0 00:00:07 005 01/23/2002 20:07:10 0 00:08:56 006 01/24/2002 20:07:10 0 00:00:06 007 01/25/2002 20:07:10 0 05:57:31 008 01/26/2002 20:07:10 0 00:46:43

9 matches found.

‘PLAY REV/FWD’ to page up/down ‘ENTER’ to play event; ‘SEQ’ to repeatedly play event.

Some options may be unavailable depending on the type of search performed. These options are not displayed.

When archiving, the unit will not allow the amount of selected data to exceed the amount of space available on the target medium.

Press the Menu button to exit the Search Results window without making a selection. Hitting the Enter button will play the selected search result. Hitting the Enter button again while in playback will cause the next selection from the search list to be

played. Press the Sequence button to repeatedly play the selected event.

0150-0193C 66 Calibur DVMRe Triplex

6 Technical Specifications

General

External Power Supply

12 Volt DC. 60 Watt (5 Amp)

Connector Power Consumption Operating Temperature Range Relative Humidity Range (Non-Condensing) Dimensions Weight

Connections

10/100 Ethernet Port RS232 Port 1 AUX Port RS232 Port 2 Camera Inputs Monitor-A Output (Y/C) Monitor-B Output (Y/C) Monitor-A Output (Composite) Monitor-B Output (Composite)

2.1mm barrel connector, center positive. 35 Watt nominal (single disk). Operating: 0 to 40°C. Storage: -20 to +60°C. Operating: 10% to 80%. Storage: 10% to 95%

17.5 x 14 x 1.7 Inches. 1U, 19 inch rack unit. 9 Lbs.

RJ-45 Connector. DB-9 Male Connector. DB-9 Male Connector. RJ-45 Connector. BNC connectors. Auto Terminating. Color & Mono. 4-pin Mini-DIN Connector. 4-pin Mini-DIN Connector. BNC Connector BNC Connector

RS485 Port SCSI Port Alarm I/O Port

Two Looping RJ-45 Connectors 50 pin, High Density SCSI-2 female connector. Use Supplied DB-25 PCB connector.

Video

Video Signal Input Video Signal Output Input Termination Display Memory Resolution Gray Scale Colors Compression Standard

0150-0193C 67 Calibur DVMRe Triplex

0.5 to 2.0 Volts peak-to-peak with Automatic Gain Control. 1 Volt peak-to-peak into 75-Ohm. 75-Ohm (Auto Terminating) 4 Megabytes Horizontal: 720 Pixels. Vertical: 484 Lines (576 for PAL). 256 levels Y:U:V 4:2:2, 16.8 Million Colors Wavelets

Audio

Audio Input

315mV, 40k Ohms. Unbalanced.

Audio Output

Alarms

Inputs Relay Configuration Record Priority Alarm Status Indicators

Motion Detection

Zones Per Camera Sensitivity Settings Gray Levels Per Zone Motion Detection Status

Output

Part Numbers

Remote Keyboard

315mV, 600 Ohms. Unbalanced.

1 per camera. User programmable as Normally Open or Normally Closed. Interleaved, Exclusive, or No Change. Relay Outputs, On-screen Indicators. Status Retrievable via RS232

port.

256: 16 x 16 grid. 10 levels 256 levels Relay Outputs, Link to Alarms, Link to Events, On-screen Indicators.

Status retrievable via RS232 port.

CBR-KB3, CBR-KB3/J, KTD405. Includes motorized pan, tilt, and zoom controls.

Rack Mount Kit Replacement Manual

CBR-RK6. 1U Height. Part Number: 0110-R601 0150-0193C.

0150-0193C 68 Calibur DVMRe Triplex

7 RS232 Event Generation/Text Insertion Protocol

7.1 Message Structure

The Delimiter byte signals the start of a new message, and has a value of 0xFF. The Class and Command fields identify the type of message. The Data Length is a 16-bit value indicating the number of bytes in the Data portion of

the message. Data Length is sent using Intel byte ordering (Little Endian). The Check Sum byte is the result of ORing all the bytes in the message.

7.2 Message Type

One message is currently supported to store text along with recorded video.

CMD_ADD_TEXT

Class byte is 0x14. Command byte is 0x40. Data Length is the number of data bytes in the message (from 2 to 502). Camera byte indicates the camera associated with the text. The valid range is from

0 to 15.

Event byte usage is described in the following section. String field contains text characters. The string can be from 0 to 500 characters in

length.

Delimiter Class Command Data Length Data Check Sum

0xFF 0x14 0x40 Data Length[0] Data Length[1] Camera Event String[0] String[1] : String[n-1] Check Sum

7.3 Event Field

The two least significant bits are currently used. All other bits should be zero.

A – Event 0x00

If both the start and end bits are clear, the associated text will be stored with the next recorded field for that camera. That cameras record rate will not be changed.

B – Event 0x01

If only the start bit is set, the associated text will be stored with the next recorded field for that camera. This will cause the selected camera, as well as any pre-event fields to be recorded at the Event Record Rate*.

C – Event 0x02

If only the end bit is set, the associated text will be stored with the next recorded field for that camera. This will start the post-event timer** after which, the selected camera will resume recording at the normal record rate*.

MSB 7 LSB 0

0 0 0 0 0 0 End Start

0150-0193C 69 Calibur DVMRe Triplex

D – Event 0x03

If both the start and end bits are set, the associated text will be stored with the next recorded field for that camera. The post-event timer will be started** after which the selected camera will resume recording at the normal record rate*.

*If no alarms are present. **If enabled.

0150-0193C 70 Calibur DVMRe Triplex

8 RS232 Remote Control Protocol

The unit supports two different communication types:

• Remote Front Panel Button Emulation

• Remote Configuration and Status

8.1 Front Panel Button Emulation

Data Structure

Byte 1: 0xFF Byte 2: 0x55 Byte 3: Front Panel Button Code

Description

Byte 1 and 2 are header bytes. Byte 3 contains the code for a specific front

panel button. The different buttons and their corresponding

codes are as follows. No Button Pressed 0

Record 1 Play 2 Stop 3 Alarm 4 Freeze 5 Zoom 6 Sequence 7 16 Way Multiscreen 8 Camera 1 9 Camera 2 10 Camera 3 11 Camera 4 12 Camera 5 13 Camera 6 14 Camera 7 15 Camera 8 16 Camera 9 17 Camera 10 18 Camera 11 19 Camera 12 20 Camera 13 21 Camera 14 22 Camera 15 23 Camera 16 24 Reserved 25 - 40 Menu 41 Enter 42

Reserved 43 Macro 44 Reserved 45-49 Monitor B 50 Reserved 51-63 Left Arrow 64 Right Arrow 65 Up Arrow 66 Down Arrow 67 Reserved 68-74 Alarm and Sequence 75 Alarm and Camera 1 76 Alarm and Camera 2 77 Alarm and Camera 3 78 Alarm and Camera 4 79 Alarm and Camera 5 80 Alarm and Camera 6 81 Alarm and Camera 7 82 Alarm and Camera 8 83 Alarm and Camera 9 84 Alarm and Camera 10 85 Alarm and Camera 11 86 Alarm and Camera 12 87 Alarm and Camera 13 88 Alarm and Camera 14 89 Alarm and Camera 15 90 Alarm and Camera 16 91 Reserved 92-110 Search 111 Frame Reverse 112 Frame Forward 113 Play Reverse 114 Stop 115 Play Forward 116 Monitor A 130 2 Way Multiscreen 131 4 Way Multiscreen 132 6 Way Multiscreen 133 7 Way Multiscreen 134 9 Way Multiscreen 135 10 Way Multiscreen 136 13 Way Multiscreen 137

0150-0193C 71 Calibur DVMRe Triplex

8.2 Configuration and Status

i) Data structure

Byte 1: 0xFF Byte 2: Command Type

0xAA: (SET) Update DVMRe with data.

0xBB: (GET) Extract data from DVMRe. Byte 3: Data Length (n) Byte 4: Data Type

0x61: Restart DVMRe

0xFE: Send configuration data to DVMRe 0x09: Read Alarm History from DVMRe 0xFF: Read configuration and status data

from DVMRe Byte 5: Data byte 1 Byte 6: Data byte 2 : : Byte x: Data byte n

ii) Sending data to the DVMRe

a) Restart DVMRe Triplex

This command will restart the DVMRe Triplex.

Byte 1: 0xFF Byte 2: 0xAA Byte 3: 0 Byte 4: 0x61

b) Send data to DVMRe Triplex

Configuration data can be sent to the DVMRe Triplex, to change the way it operates. The data is arranged in the form of 16 byte blocks, numbered from 1 to 213. Blocks 182, 183 and 185 are status blocks, and hence cannot be written to. For details about the contents of each block, contact GE-Interlogix and request the Block Data Structure for the DVMRe Triplex.

Byte 1: 0xFF Byte 2: 0xAA Byte 3: 17 Byte 4: 0xFE Byte 5: Block Number

(1-181, 184, 186-213)

Byte 6: data[0] : : : : Byte 21:data[15]

After sending a block or series of blocks, block number 255 must be updated to signal the end of the configuration session. All data bytes for block 255 must be set to 0.

iii) Requesting data from the DVMRe

When a message of type 0xBB is sent to the DVMRe Triplex, it will respond by sending 16 bytes of requested data.

a) Read Alarm History List

Byte 1: 0xFF

Byte 2: 0xBB Byte 3: 0 Byte 4: 0x09

When the "Read Alarm History List" message is received by the DVMRe Triplex, it responds by sending a start byte 0xFF, followed by ASCII strings for every alarm event in its alarm history list, and a stop byte, 0xFF. Each string is formatted as follows:

dd.bmm/ddbhh:mm:ssbaa<CR><LF>

dd: index number (00 - 99) b: space character mm: month (01-12) dd: day (01-31) hh: hours (00-23) mm: minutes (00-59) ss: seconds (00-59) aa: alarm number (01-16) <CR> Carriage return (0x0D) <LF> Line feed (0x0A)

Example: 03. 11/27 22:48:58 15

b) Read data from DVMRe Triplex

Configuration and status data can be read from the DVMRe Triplex. The data is arranged in the form of 16 byte blocks, numbered from 1 to 213. For details about the contents of each block, contact GE-Interlogix and request the Block Data Structure for the DVMRe Triplex.

Byte 1: 0xFF Byte 2: 0xBB Byte 3: 1 Byte 4: 0xFF Byte 5: Block Number 1-213 or 255 if all

blocks are requested.

The DVMRe Triplex responds to the “Read data” request by sending all the requested data bytes consecutively, without any start or stop bytes.

A total of either 16 bytes or 3408 bytes will be transmitted, depending on whether a single block or all the blocks were requested.

0150-0193C 72 Calibur DVMRe Triplex

9 Macro Tables

Photo copy this page and use it to keep a record of the programmed macro functions.

9.1 Macro Functions Table

Macro Number

Description

Function + Sequence

0150-0193C 73 Calibur DVMRe Triplex

Daylight Savings Time: Sets clock ahead one hour in April, and back one hour in October.

9.2 Scheduled Macro Table

Event Day Time Macro to Run

0150-0193C 74 Calibur DVMRe Triplex

10 Warranty and Service

10.1 Factory Service

Warning: Do not open the top cover or attempt to service the unit, as this may expose

you to dangerous voltages and other hazards. Programmer maintenance of this unit is limited to external cleaning and inspection. Refer all servicing to qualified personnel.

If the unit requires factory service, contact the dealer who supplied the unit to you for the correct procedures on returning the unit to the factory or the nearest factory service center.

If the dealer is not available, contact the manufacturer of the unit as detailed below and request a Return Material Authorization number (RMA). The unit’s serial number must be provided before a RMA number can be issued. Units returned to the factory for service must have freight and insurance prepaid, and must show the RMA number clearly on all shipping documents. The failure symptoms must be clearly described by the operator and enclosed with the unit together with a copy of the original suppliers invoice. Failure to comply with these instructions will delay service of the unit, and may result in the unit not being accepted by the Repair Center.

Factory Address

GE-Interlogix, Kalatel Division

Attention: Repair Center 3197-C Airport Loop Drive Costa Mesa, CA. 92626 United States of America Telephone: 800-343-3358 (7:00 AM to 4:30 PM, Pacific Time) In Oregon: 541-754-9133 Fax: 541-754-7162 (24 hours a day)

For warranty information, see the following page.

0150-0193C 75 Calibur DVMRe Triplex

10.2 Warranty and Return Information

GE-Interlogix warrants all of its equipment for three years from the date of purchase. This warranty covers any defects in materials and workmanship. Equipment failures that are due to improper installation, modification, abuse, or acts of nature will not be covered by this warranty. The repair department will evaluate all equipment returned for repair to determine warranty coverage. The Tech Support Manager will resolve any questions that may arise during evaluation to make a final determination.

Note: The three-year warranty does not apply to the following products:

MobileView® and the monitor CRT, which carry a 12-month warranty from the date of purchase.

The warranty specifically covers any defects in material and workmanship and does not cover equipment that has been abused, damaged, or modified.

For all warranty repairs, GE-Interlogix will cover all costs, including parts, labor, and shipping. Repaired equipment will be returned via the same method of shipment in which it was received. If a customer requests a faster return shipment, the difference will be charged.

For all non-warranty repairs, the customer will be billed for parts, labor, and shipping. Labor will be billed in half-hour increments.

Note: Customers requesting an estimate prior to repair will be notified by phone. If they cannot be reached, they will be notified by fax. If we are unable to reach the contact person for repair authorization after one phone attempt and two fax attempts, the equipment will be returned without being repaired. We will hold equipment no longer than two weeks.

Advance Replacement Policy

When an advance replacement is required, we will send the customer replacement equipment from our stock and receive the returned product in exchange. The received equipment will be evaluated and the repair department will determine whether it is a warranty replacement. If it is non-warranty, see our repair policy above for details. The following guidelines will be used for all advance replacements:

• Fewer than 45 days from purchase, GE-Interlogix will replace the product with new equipment.

• From 45 days to 1 year from purchase, GE-Interlogix will replace the product with refurbished

equipment.

• From 1 year to 3 years from purchase, the product must be sent in for repair. Advance replacements will be sent for a fee of $100.

If you have questions about this policy, please contact GE-Interlogix Kalatel Division’s RMA Department at 800-469-1676.

0150-0193C 76 Calibur DVMRe Triplex

0150-0193C

GE 0150-0193C User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual