GD Midea Air conditioning Equipment MDNA14 User Manual
USER MANUAL OF SMART KIT
MODEL:OSK101
SK101
Complies with
IDA Standards
Da105762
GD MIDEA AIR-CONDITIONING EQUIPMENT CO.,LTD.
CONTENTS
1
DECLARATION OF CONFORMITY.........................1
2
SPECIFICATION..................................................1
3
PRECAUTIONS ...................................................1
4
TECHNICAL SOLUTION ......................................3
OPERATION INSTRUCTION ................................5
5
APP USAGE ......................................................14
6
FAQ...................................................................23
7
DECLARATION OF CONFORMITY
1
Hereby, we declare that this AC is in compliance
with the essential requirements and other relevant
provisions of Directive 1999/5/EC. The declaration
of conformity may be consulted with sales agent.
SPECIFICATION
2
Standard:IEEE 802.11b/g
Antenna Type:PCB layout Antenna
Frequency:WIFI 2.4-2.4835GHz
Maximum Transmitted Power: 20dBm Max
Dimension:76*28*13mm
Operation Temperature:0 C~45 C/32 F~113 F.
Operation Humidity:10%~85%
Power Input:DC 5V/300mA
FCC ID:2ADQOMDNA14
IC :12575A-MDNA14
3
PRECAUTIONS
Applicable system :IOS, Android.
Please check the service website for more
applicable devices.
Disclaimer:Due to the special situation existed
during App use,we explicitly claim as bellow:
Not all of the Android and IOS systems are compatible
with the APP.We will not be responsible for any issue
as a result of the incompatibility
SMART KIT wireless safety strategy.
Smart kit Only support WPA-PSK/WPA2-PSK
encryption and none encryption .
WPA-PSK/WPA2-PSK encryption is recommended.
OOO O
This device complies with Part 15 of the FCC Rules
and RSS 210 of Industry & Science Canada.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
Le present appareil est conforme aux CNR
d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisee aux
deux conditions suivantes : (1) l'appareil ne doit pas
produire de brouillage, et (2) l'utilisateur de l'appareil
doit accepter tout brouillage radioelectrique subi,
meme si letbrouillage est susceptible d'en
compromettre le fonctionnement.
Only operate the device in accordance with the
instructions supplied. This device complies with FCC
and IC radiation exposure limits set forth for an
uncontrolled environment. In order to avoid the
possibility of exceeding the FCC and IC radio
frequency exposure limits, human proximity to the
antenna shall not be less than 20cm (8 inches) during
normal operation.
Changes or modifications not expressly approved by
the party responsible for compliance could void the
user's authority to operate the equipment.
¢Ü
1
2
TECHNICAL SOLUTION
4
1. WIFI Router Home Control Mode.
A WIFI router is needed at this mode. Smart phone
and connect to the AC through the WIFI router
conditioner.
1 Smart Phone
2 Smart Air conditioner
3WIFI Router
2. How to install the smart kit
1
Remove the protective cap of the smart kit
2
Open the front panel and insert the smart kit into
the reserved port
3
Attach the QR code packed with SMART KIT to the
side panel of the machine, ensure it is convenience
to be scanned by the mobile phohe.
Insert
3
4
OPERATION INSTRUCTION
5
1.Install App
1).Iphone Users:scan QR Code or go to App Store and
search for NetHome app and download it.
2).Android Phone users:scan QR Code or go to
google play, search for NetHome app and
download it
2.How to reset the WIFI to defaults?
When you first time use WIFI function, it is necessary to
make the Air Conditioner(AC) to enter the WIFI Network
Setting Mode to do settings. The procedure includes the
following steps:
1) Disconnect the power supply of AC
2) Connect the power supply of AC, and continuously
press the LED or DO NOT DISTURB or
button (depending on the remote controller
seven times in 3 minutes.
3) When the AC displays AP , it means that the AC WIFI
has already entered into the WIFI Network Setting
Mode.
4) When the AC WIFI entered into WIFI Network Setting
Mode, the Air-conditioning remote control can't open
the AC. It needs to wait 3-5 minutes or when the AC
finish the WIFI Network Setting Mode, then the
Air-conditioning remote control can control AC
normally.
5)If there is no set operation under WIFI Network setting
mode,AC will quit this mode automatically 8 minutes
later ,and then the user can control the AC normally.
'
'
5 6
3.Set AC connected to router
(for WIFI router home control mode only)
When first using, set the AC and connect the to router.
use the control software to set the AC after connect the
phone touter
1) Reset the AC to defaults.
2) Turn on the power of AC, enter the WIFI setting of
smart phone, find the router with name Nethome ,
connect the smart phone to the AC.
3) Open the APP on the smart phone, do following
settings:
Using Apple device to link the air conditioner with
your WIFI Network connection
'
'
1
Click WIFI
2
Select NetHome
3
Go to Network
Select your WIFI network.
4
Using Android device to link the air conditioner with
your WIFI network connection.
1
Enter your WIFI password
5
and click on OK.
7 8
Go to Network.
Click on Scan QR
2
Code.
Loading...