GBC Shredmaster 7500S, Shredmaster 7550X User Manual

Español
1
IMPORTANT
To quickly and easily confirm your warranty, register your new
shredder online at www.gbcconnect.com
IMPORTANTE
Para confirmar su garantía rápida y fácilmente,registre su nueva
IMPORTANT
Pour confirmer votre garantie rapidement et facilement, enregistrez
votre nouveau déchiqueteur en ligne à www.gbcconnect.com
SHREDDERS 7500S
7550X
EnglishFrançais
Your safety as well as the safety of others is important to GBC. In this instruction manual and on the product are important safety messages. Read these messages carefully.
The safety alert symbol precedes each safety message in this instruction manual and on the product. This symbol indicates a potential personal safety hazard that could hurt you or others, as well as cause product or
property damage. Do not connect this unit to electrical power or attempt to operate it before you have read these operating instructions. Save these instructions for later use.
Important Safety Instructions
The following warning is found inside of the cabinet door:
This safety message means that you could be seriously hurt or killed if you open the product and expose yourself to hazardous voltage.
The following warning is found on the bottom of the product:
This safety message means that you could be seriously hurt if you place your hands in the discharge area.
This means don’t reach into the feed opening of the cutting head. This could hurt you.
This means you should be careful because long hair can become entangled in the cutting head. This could hurt you.
This means be careful of ties and other loose clothing which could become entangled in the cutting head. This could hurt you.
This means you should be careful of loose jewelry which could become entangled in the cutting head. This could hurt you.
This means do not allow children to use the shredder.
2
English
ELECTRICAL SAFEGUARDS
Unplug your shredder before moving it, emptying the bag, or when it is
not in use for an extended period of time.
Do not operate with a damaged power supply cord or plug, after it
malfunctions, or after it has been damaged in any manner.
Do not overload electrical outlets beyond capacity as this can result in
fire or electrical shock.
The socket-outlet should be installed near the equipment and shall be
easily accessible.
Do not alter attachment plug. Plug is configured for the appropriate
electrical supply. Do not use near water. Keep out of the reach of children. Do not use extension cords to connect this product to the power supply.
SERVICE
Do not attempt to service or repair the unit yourself. If your shredder should require service, contact your local dealer or call GBC National Service at 800-790-7787. Please have the model and serial number of your shredder ready when calling.
3
Figure 1. The door must be closed when operating the shredder.
Figure 3.
4
Figure 2. Keep the area around the electrical outlet clear.
Unplug the shredder before cleaning it.
Do not perform any repairs on the shredder. (See page 12).
Figure 3. Do not shred CDs or DVDs
in the cross cut model (7550X). It may splinter disks and kick them back out. Only the straight cut model (7500S) is suitable to destroy CDs or DVDs.
Do not attempt to shred paper clips with the cross cut model.
120V / 120A min.
Figure 1.
Figure 2.
English
Figure 4. Do not operate the shredder without the safey guard in place.
Figure 5. The shredder turns off after one hour of inactivity. Turn the power switch off when not in use for extended times.
5
Figure 4.
Figure 5.
Set Up
A
2.
1.
ASSEMBLY
Figure 6.
Plastic Bag
Pull out the waste receptacle frame and remove the round belt from around the frame.
Insert the included plastic bag through the pull-out frame and fold the top of the bag over the frame.
Secure the bag with the round belt.
Slide the waste receptacle in and close the cabinet door.
Oiler
Hook the oiler holder over the edge of the cabinet.
Remove the sticky tape from the oil tube.
Remove the cap from the oil bottle, insert the oil tube into the bottle, and tighten the cap.
Place the oil bottle in the holder.
The oil bottle has a fill level indication
(A). Figure 7. Plug cord into the electrical
outlet. Keep the area in front of the outlet
clear for easy access.
1.
a.
b.
c.
d.
2.
a.
b.
c.
d.
6
Figure 6.
Figure 7.
English
OILER
Figure 8. When using for the
first time or when the oil bottle is changed:
Press until the EMPTY LED
(A) no longer blinks red.
Figure 9. Flashing INJECT LED:
Indicates cutting shafts are
being automatically oiled.
Flashing EMPTY LED:
Indicates oil bottle is empty.
7
A
A B
Operation
Figure 8.
Figure 9.
OPERATING THE SHREDDER
Figure 10.
Press the forward button to turn the shredder on. The green light
shows that the shredder is ready to operate.
Feed paper in to the middle of the the throat. An auto sensing photo cell detects the paper and starts the machine. The shredder stops automatically when no more paper is inserted.
STANDBY MODE
After one hour of inactivity, the shredder goes into standby and the
green LED turns off. Repeat step 1 above to turn the shredder back on.
1.
2.
SHEET CAPACITY INDICATOR
Figure 11.
The shredder has an ECC (electronic capacity control) which indicates the sheet capacity being used during shredding (A).
Red LED (A). The shredder stops automatically if too much paper is inserted. The paper is reversed.
Yellow LED (B). Maximum sheet capacity during shredding.
Green LED (C). Normal capacity during shredding.
8
A
2.
1.
Figure 10.
Figure 11.
English
Figure 12. Shredder stops automatically when door is opened and a red LED indicator lights.
Figure 13. The shredder stops automatically when the plastic bag is full. Empty the bag when the “bag
full” yellow indicator lights. (
See page 6).
9
Figure 12.
Figure 13.
Figure 14. The shredder stops automatically when too much paper is inserted at the same time. The shredder features an automatic reverse function that will be activated when too much paper has been inserted.
Figure 15. If necessary, when a paper jam occurs and the automatic reverse function does not clear all of the paper, press the reverse button to reverse the cutting unit and release the paper.
Note: The auto sensing photo cell must not be obstructed.
Once the shredder is clear, re-insert smaller quantities of paper.
10
Figure 14.
Figure 15.
English
Figure 16. The shredder automatically stops if the safety
guard (A) is opened (symbol flashes ). Close the safety guard to shred paper. To remove any paper debris from a paper jam, the machine runs for a short time in reverse with the safety guard open. If required, press the reverse button several times.
11
Figure 16.
Troubleshooting
12
A
B
Symptom Corrective Action
Machine will not start. Plug unit in.
Switch unit to Power On by pressing the forward button (green LED lights). Feed paper in to the center of the feed opening where the auto sensing photo cell is located. Close the cabinet door. Empty the shred bag. Close safety guard.
Bag full indicator lights but bag is not full.
Figure 17.
Unplug unit from electrical outlet. Remover paper debris between the cutting head from below with a brush (not included). Figure 18.
Figure 17.
Figure 18.
English
13
Symptom Corrective Action
Machine will not stop. Unplug unit from electrical outlet.
Clean the auto sensing photo cell with a small brush (not included). Figure 19.
Machine stops. Overload protection. Allow unit to cool down
approximately 5 to 10 minutes.
Symbol flashes When symbol stops flashing, machine is
ready for operation.
If none of the troubleshooting actions correct the problem, contact your local dealer or call GBC National Service at 1-800-790-7787.
Figure 19.
Accessories
Environmentally safe oil 33.8 oz. (1 litre) Part number 1753190
Shredder bags for models 7500S and 7550X (100 bags) Part number 1145482
To order, visit www.gbcconnect.com or call 1-800-723-4000.
14
Loading...
+ 30 hidden pages