Gate Bure Ortho 56-317T, Bure Space 56-304 Instructions For Use Manual

Instructions for use
Bure
Walker
TM
digital
Bure Space 56-304
Raising/lowering the frame
Adjust the height with the aid of the remote control <UP> and <DOWN> arrows.
Adjusting the handles
To adjust handles to the desired position; undo knob, adjust handle, tighten knob.
Dear User,
Congratulations on obtaining a Bure Walker! These instructions provide important information on how to use the walker and how to maintain it.
All of us here at GATE Rehab Development hope you enjoy using your new product. If you have any comments, questions or points of view, please contact us on +46 371 31800.
Left and right adjustment of armrests
The armrests can be adjusted sideways for optimal support; undo knob, adjust armrest, tighten knob.
NOTE! The rear attachments on the frame/armrest are interchangeable (left with right and vice versa) to provide different widths. The locating pins on the cushion’s underside/rear can also be moved. These adjustment capabilities make customization possible.
Upp
Ned
Min
Max
Justering av armstödsplattor (Hö/Vä)
För optimalt stöd kan Armstödsplattor breddjusteras: Ratt lossas, armstödsplattas läge justeras. Ratt låses
Låsning av hjul
Hjulen låses genom att fotbroms aktiveras.
Upplåsning av hjul
För att lossa bromsen – återställ.
Justering av armstödsplattor (Hö/Vä)
För optimalt stöd kan Armstödsplattor breddjusteras: Ratt lossas, armstödsplattas läge justeras. Ratt låses
Kopplingsschema Styrbox
(Bure El/Bure Double/Bure Extra)
2
3
4
5
Locking castors
Depress the foot brake to set it and lock the castor.
Unlocking castors
Press down on the protruding part of the brake to release it.
Control box wiring
Remove the control box cover to make the connections as described below. Use a screwdriver or similar; refer to the special labels on the control box.
1. Socket for the raise/lower actuator. NOTE! Make sure that plugs are connected to the correct sock­ets otherwise the actuators can be damaged.
2. Remote control socket.
3. Battery terminal socket.
4. Plug socket. NOTE! The plug must ALWAYS be connected to the control box for IP protection to be valid.
2
3
4
1
Battery charging
LEDs on control box and battery
• Connect plug to 230V wall socket. Charging begins auto­matically and the battery LED flashes green.
• Make sure the battery is fully charged before using for the first time. It takes around
25 h to fully charge the battery.
• We recommend that the battery plug be removed from the control box if the product will be out of use for an exten­ded period (more than one week) or if the battery is swit­ched off by means of the ON/OFF switch. This eliminates the risk of disabling the battery as the control box always uses a small quantity of electricity even when the walker is not in use.
• Control box – green light when power is available from bat­tery/mains socket.
• Battery:
• The LED flashes green during
charging.
• ON/OFF: To use the product,
press ON.
• The green lamp will begin to flash.
• Use the OFF button (hold down for 5 s) to switch off the
battery if the product will not be used for an extended period.
• The LED will shows a constant green light when the battery
is fully charged.
• When the battery is in normal state/in operation, the LED
• flashes green at REGULAR intervals, namely 0.5 s ON, 4 s
OF F.
• When the battery requires charging (remaining charge
<25%) the LED will flash
• orange/red at REGULAR intervals, namely 0.5 s ON, 4 s
OF F.
NOTE! The battery has an in-built device that automatically switches it off when remaining charge is <20%. The LED is then extinguished. The battery must now be fully charged before the electronics can be used again.
Maintenance
Recommended at least once per year.
General
The walker feels firm/free from play. The walker does not rattle during manoeuvres. The walker is level and all of its castors are in contact with the floor. The walker is not dirty.
Armrests Arm rests are intact and clean. Arm restwidening is functional.
Handtag Grips are not damaged/dirty.
Handle adjustment is functional.
Battery Check that the charging cable is connected to the control box.
Check that the remote control is connected to the control box.
Check that connections are made according to the wiring diagram.
Check that the batter y, actuators and control box are not loose.
Height adjustment Raising and lowering are functional.
The walker feels stable at maximum settings.
There is no play between the vertical frame and bottom frame. Height adjustment clamps lock.
The electric actuator fitting must be free from play. Height adjustment via remote control is functional. The electric actuator must run smoothly at a constant speed.
Frame parts There is no mechanical damage.
There are no scratches. End plugs/lower frame fitted.
Castors/brakes Castors roll easily/tread not damaged.
The castors are tightly fastened to the lower frame.
Castor brakes functional on all castors. Handbrake functional.
Clean with lukewarm soap solution or alcohol-based cleaning agent (no petroleum products).
Clean; replace if damaged. Fit lock knobs/plates as required.
Clean with lukewarm soap solution (no petroleum products). Replace handle grips. Fit lock knobs/plates as required.
Fit new cable; this must always be connected to the control box (IP65 classification). Connect or fit new remote control as required.
Refer to the wiring diagram in the Technical manual.
Tighten; replace with new fasteners as required.
Fit new guide sleeves (in frame) or end plugs (in chrome tubes) as required.
Tighten all lock bolts.
Replace clamps.
Tighten the attachment fitting concerned; replace bolts/lock nuts as necessary. Check that the battery/remote control/ actuator are connected in accordance with the wiring diagram. Charge the battery. Contact customer services.
If damage is present, contact GATE’s customer services. Touch up as necessary. Fit new end plugs.
Clean or replace castors (NOTE! Castors are always fixed to the lower frame with thread locker or lock nuts. The castors are sealed and we do not recommend their dismantling; instead, replace the whole castor assembly. Tighten the castor bolt and fit locking nut or use thread locker (depends on model).
Replace castor assembly. Adjust the brake or fit new castors.
Check that Action
20 16 -0 4 -11, 3
General maintenance advice
• Wipe the walker and its armrests clean as necessary; use soap solution or alcohol-based surface disinfectant.
• The product may be cleaned in a tunnel washer or similar as electrical systems have IP65 protection. However, the product is not corrosion proof which means washing by machine may reduce its service life.
• Replace damaged parts immediately; must be done by experienced personnel.
• The product is only intended for indoor use.
Technical specifications
Dimensions apply to walkers with 125 mm castors.
CE marked according to MDD 93/42/EEC. Tested and approved according to EN-11199-3/2005
Bure Space
Part No.
56-304
Width 78 cm
Max user weight 150 kg
Length 79 cm
Height
90-130 cm
Armrests/ internal dimensions
25-50 cm
Bure Ortho
Part No.
56-317 T
Width 78 cm
Max user weight 150 kg
Length 80 cm
Height 90-130 cm
Armrests/ internal dimensions
25-50 cm
Would you like to know more?
Contact us at: Tel: +46 371 31800 Gate Rehab Development AB Industrigatan 2 | SE-330 21 Reftele info@gaterd.com | www.gaterd.com
Loading...