Gasmate GM135-010 User Manual

Electric Heater with Stand

Model No. GM135-010

4151-05/15

Designed for outdoor use

Important: Retain these instructions for future use.

INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS

BEFORE FIRST USE

• Read and follow all the instructions below even
if you feel you are familiar with the heater.

• Remove the packing and make sure that the
heater is intact. If in doubt do not use the
heater and contact the place of purchase.

• Do not leave packaging materials such as bags
and staples within reach of children.

• Dispose of packaging carefully and with
consideration for the environment.

• It is ideal to retain the heater carton for
seasonal storage.

For your convenience record the date you
received the heater on the warranty page of these
instructions, and attach your proof of purchase.
Retain this information in the event that a
warranty service is required.

NOTE: The rating of this heater (as marked on

the rating label) is based on specic loading tests.

Normal use or the use of other recommended

attachments may draw signicantly less power.

IMPORTANT SAFETY INFORMATION

Before attempting to operate this heater, the
following basic safety precautions should be

taken to reduce the risk of re, electric shock

and personal injury. It is important to read
the instruction manual and to understand its’
applications, limitations and potential hazards
associated with this heater.

WARNING: DO NOT

COVER IN ORDER TO

AVOID OVERHEATING.

To reduce the risk of re, electrical shock or

injury to persons or property:

• To avoid overheating, keep airow grilles

clear of dust and hair build up - especially if
you have indoor pets.

• Use only the voltage specied on the rating

label of the heater.

• Do not cover or restrict airow to the inlet

or outlet grilles in any manner as the heater

may overheat and become a re risk.

• Do not cover grilles, block entry or exits of

airow by placing the heater against any

surface. Keep all objects at least 1 metre
from the front, side and rear of the heater.

• Do not locate in areas of high foot trafc,

ensure the power cord and heater are in
view to avoid accidents.

• Do not operate in areas where gasoline,

paint or other ammable liquids are used or

stored.

• This heater heats up when in use. To avoid
burns, do not touch the front of the heater
or any of the grilles or vents.

• Before moving the heater, switch off the
heater by unplugging it from the wall and
allowing it to cool.

• Do not use the heater to dry clothes.

• Do not insert or allow foreign objects
or metal utensils into any ventilation or
exhaust openings as this may cause an

electric shock, re or damage to the heater.

• Do not use this heater in the immediate
surroundings of a bath, a shower or a
swimming pool.

• Do not immerse in liquid or use the heater
within 1m or above a water source as this
could create an electrical shock hazard.

• If the heater accidentally comes into contact
with water switch off the power supply and
do not touch the heater.

• Do not operate any heater with a damaged
cord or plug or after the heater malfunctions
or has been dropped or damaged in any
manner – in order to avoid a hazard. Return

to a qualied electrical person for service or

repair.

• Do not operate the heater with wet hands.

• Do not connect the heater to the mains
voltage until completely assembled and
adjusted.

• Always operate upright, on a at surface

only.

• CAUTION: This product is NOT suitable to
be used on long pile carpets or rugs.

• Unroll the cord before operating. Operating
with a coiled cord may cause overheating

and re risk.

• This heater is NOT designed to run off an
extension cord. If you require an additional
power point please have one installed by a

qualied electrician.

• Do not remove the plug from the power
socket until the heater has been switched
off.

2

• The use of extension cords may cause
power voltage loss which will result in
damage to the heater this will NOT be
covered under warranty.

• Always hold the plug when removing it from
the wall, do not pull the cord.

• Always unplug the heater when it is not in
use.

• Do not allow the cord to come in to contact
with the heater surface during operation.

• Do not run the cord under carpeting, mats
or rugs etc. Arrange the cord away from

trafc areas so that it will not be tripped

o v e r.

• Do not twist, kink or wrap the cord around
the heater as this may cause the insulation
to weaken and split.

• This heater is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge,
unless they have been given supervision or
instruction concerning use of the heater by
a person responsible for their safety.

• Children should be supervised to ensure
that they do not play with the heater.

• This heater is intended for light domestic
use and not for heavy duty commercial or
industrial use.

• The heater must not be located immediately
below or in front of a socket-outlet.

• CAUTION: In order to avoid a hazard due to
inadvertent resetting of the thermal cut-out,
this heater must not be supplied through an
external switching device, such as a timer,
or connected to a circuit that is regularly
switched on and off by the utility.

• Never remove the cover of the heater – in

case of a fault contact a qualied service

person.

• Repairs should only be carried out by

qualied persons using original spare parts.

Failure to do so may result in considerable
danger to the operator.

• Use this heater only as described in this
manual.

• Any other use is not recommended by the

manufacturer and may cause re, electric

shock or injury.

Installation

This heater is not designed for use within 1m or
above a water source.

Ensure that the heater is not positioned directly
above, below or in front of a power point or
switch.

This heater is not designed to be used with 3rd
party timer or programmable system.

This electric heater complies with New Zealand
and International standards and safety
requirements. All installations must meet the
requirements of New Zealand Standard
AS/NZS 3000:2007.

FOR YOUR SAFETY

WARNING: Fire risk exists if this heater is
covered by or positioned close to curtains or
other combustible materials.

NOTE: Ensure that this heater is connected
directly to an outdoor power point.

The electrical system of this heater must be
connected with an automatic circuit breaker
and/or residual current device (RCD). If

uncertain have a qualied electrician check

your electrical system before installation and/
or use.

All electrical connections are made in a dry
area.

Outdoor power points must be weatherproof

and installed by a qualied electrician.

The distributor is not responsible for

incorrectly chosen additional xing accessories

or any damage which may be caused by an

incorrectly tted heater.

3

SPECIFIC SAFETY INSTRUCTIONS

WARNINGS

Do not use the heater in areas where there is a

risk of explosion or re from ammable gases.

Ensure that the heating area is kept clear of
combustible materials. Do not use the heater in
damp areas, without suitable ventilation. This
heater is not designed for use within 1m or
above a water source. Do not place within one
metre (1m) of any water source. Do not place
directly in front of, below or above any power
points or switches.

Fire risk exists if this heater is covered by or
positioned close to curtains or other combustible
materials.

• This heater is intended for domestic/
household use only.

• This heater is designed for outdoor use.

• Always ensure that this heater is installed as
per the requirements noted in New Zealand
Standard AS/NZS 3000:2007.

• Always keep heater at least one metre (1m)
from combustible materials.

• DO NOT locate this heater directly below,
above or in front of the power supply socket
or switch.

• DO NOT use this heater in either a bathroom
or ensuite.

• DO NOT use a 3rd party timer, or
programmable system with this heater.

• DO NOT clean the heater while the heater is
on or plugged into the mains power supply.

• DO NOT touch any part of the heater while on,
hot surfaces may burn.

• DO NOT use the heater as a dryer.

• DO NOT attempt to modify the heater, power
cord, power plug or the supplied accessories
in any way.

• DO NOT expose the heater to rain, water, or
use in damp wet conditions.

• NEVER cover this heater.

• NEVER carry the heater by its power supply
cord.

• NEVER use with the power cord coiled,
bundled up or tied up. Always extend fully
before use.

• NEVER use the heater if any part of it is
damaged.

• Ensure that the heater is disconnected from
the mains supply when installing, cleaning or
removing/installing.

• Ensure this heater is not left on when
unattended.

• Ensure the heater is not used in areas where

ammable gases are present, e.g. paint,

petrol etc.

• Always turn the heater OFF at the unit switch
and the power point switch when not in use
for extended periods of time.

• Always allow the heater to cool, about one
(1) hour after the heater has been turned off,
before cleaning the heater.

• Always ensure that the power cord is fully
extended and NOT in contact with any part of
the heater.

• Always ensure that the heater is kept clean
and free from dust.

• Only use this heater on a level surface.

4

ELECTRICAL DATA ASSEMBLY INSTRUCTIONS

IMPORTANT

This product is tted with a sealed electrical

connection plug that is compatible with the heater,
the mains supply for New Zealand and meets
the requirements of international standards. This
heater must be connected to a supply voltage that
is equal to that stated on the rating label.

If the mains connection plug or power cord
becomes damaged it must be replaced with a
complete assembly that is identical to the original,
and this must be replaced by an authorised
service centre.

Always follow the New Zealand requirements for
connection to the mains supply. If in doubt always

consult a qualied electrician.

Technical Specication

Model GM135-010

Voltage: 220V-240V~ 50Hz

Input Wattage: 1800W

Unit Weight: 11.7Kg

IP Rating: IPx4

Heater specications can be found on the data

label.

For best results and your safety, please follow the
instructions carefully. DO NOT modify this product
in any way as the distributor will accept no liability
for improper use.

PARTS LIST

No. Part Name

1 Control box/Heater Head

2 Remote control

3 Cord Clip x 3

4 Screw x 4

5 Upper Tube extension

6 Adjustable Fastener

7 Upper Tube

8 Middle Tube

9 Lower Tube

10 Base

11 Washer

12 L Screw

13 Long screw

Note: Extra Cord Clips are included in case
replacement is required.

5

ASSEMBLY INSTRUCTIONS

INSTALLATION

Step 1

Insert Lower Tube (9) into Base (10) ensuring
that tab on Lower Tube slots into hole in Base.
Carefully turn the Base/Lower Tube assembly
upside down and secure Lower Tube to Base with
Washer (11) and “L” shaped screw (12). Please
tighten screw completely before moving on to next
step.

Step 2

Insert Middle Tube (8) onto top of Lower Tube
assembly, Lower Tube will slide inside Middle Tube.
Line up the screw holes in Middle Tube with screw
holes in Lower Tube. Secure with 2 x Screws (4)
and tighten.

Step 3

Release and extend out Upper Tube Extension
(5) from Upper Tube (7) by turning Adjustable
Fastener (6) counter clockwise. Once Upper Tube
extension is fully out tighten Adjustable Fastener
by turning clockwise. Insert Tube Extension into
the back mounting hole in Control Box (1). Secure
with Screw (13).

Step 4

Insert base of Upper Tube into top of Middle
Tube, Middle Tube will slide inside Upper Tube (as
step 2). Line up the screw holes in Upper Tube
with screw holes in Middle Tube. Secure with 2 x
Screws (4) and tighten.

Fig. A

Fig. B

Fig. C

Step 5

Clip power cord into Cord Clips down the back of
Upper/Middle and Lower Tubes.

Step 6

Heater head can be adjusted to various angles by
loosening and then tightening the screw on the
side of the Control Box as shown in Fig. C.

Step 7

The height of the Heater head can be adjusted by
turning Adjustable Fastener (6) counter clockwise
and adjusting the head to desired height. Then
tighten Adjustable Fastener by turning clockwise.

Step 8

Place 2x AAA batteries in Remote Control.

6

CLEANING AND CAREOPERATING INSTRUCTIONS

POSITIONING THE HEATER

The heater should only be operated at a minimum
distance of 1 metre from any wall or other object.
Position the heater in order to optimise the air

ow of the area.

IMPORTANT

• Heater must not be located immediately
below a socket outlet.

• Heater must not be located in front of a
socket outlet.

TO OPERATE

1. Plug power cord into 240V AC power point.

2. To turn on - switch the power point on.

3. Switch heater ‘ON’ at the back on the Control
Box. The front indicator light will blink to show
that the heater is ready for operation.

4. Press the ‘ON’ button on the front of the Control
Box under the heater head or press ‘ON’ on the
Remote Control. The Indicator light will stay on
when the heater is operating.

5. To turn off - switch off the heater by using the
“OFF” button on the front of the control box or
on the remote control.

6. Then switch off the heater at the back of the
control box and then off at the power point.

7. Unplug lead from power point when not in use.

IMPORTANT: Turn off the heater. Switch off the
power switch and disconnect the heater from the
power socket. Wait for the heater to be completely
cool before cleaning (at least one hour).

• Vacuum clean air vents and grilles to remove
dust from these areas.

• To remove dust on external surfaces, wipe the
heater with a damp (not wet) lint- free cloth
rinsed in hot soapy water only.

• DO NOT use solvents, e.g. Petrol, Toluene,
Methylated Spirits etc to clean the heater, as

these will damage the surface nish and may
cause a re when unit is next used.

• DO NOT spray with liquids or submerge in
liquids or water.

• DO NOT allow water or mild dish washing
solution to enter or drip onto the heater.

• DO NOT attempt to clean the interior of the
heater.

• DO NOT attempt to open the heater casing at
any time.

STORAGE

• Store the heater carefully in a dust-free area

during the off season. It is ideal to store the
heater in the carton it was supplied in. Neatly
wind the cord of the heater to prevent damage
to the cord.

Gasmate® is a registered trademark of: Sitro Group Australia Pty Ltd www.gasmate.com.au
Aber, Hamilton, N.Z. www.gasmate.co.nz

7

8