Gas-Fired Products PTS 40, PTS 75, PTS 150, PTS N7-L7, PTS 200 User Manual

INSTALLATION AND OPERATION INSTRUCTIONS

OWNER / INSTALLER: For your safety this manual must be carefully and thoroughly read
and understood before installing, operating or servicing this heater.

INFRARED RADIANT TUBE HEATER

Two Stage Push Through System (Positive Pressure)

Models

:

PTS SERIES: (40, 50, 75, 100, 125, 150, 175, 200) – N7/L7

PTU SERIES: (40, 50, 75, 100, 125, 150, 175, 200) – N7/L7

!INSTALLER: This manual is the property of the owner. Please present this manual to
the owner when you leave the job site.

WARNING: Improper installation, adjustment, alteration, service, or maintenance can
cause property damage, injury or death. Read the installation, operation and maintenance
instructions thoroughly before installing or servicing this equipment.

IF YOU SMELL GAS:



^ DO NOT try to light any appliance.
^ DO NOT touch any electrical switch; DO NOT use any

telephone in your building.

^ IMMEDIATELY call your gas supplier from a neighbor's

telephone. Follow the gas supplier's instructions. If you
cannot reach your gas supplier, call the fire department.

!IMPORTANT

Post Office Box 36485 (28236)  305 Doggett Street (28203)  Charlotte, North Carolina

Phone [phone]  Fax [phone]  www.spaceray.com  email: [e-mail]

Form #43343530
July 08

FOR YOUR SAFETY

: SAVE THIS MANUAL FOR FUTURE REFERENCE.

SPACE-RAY

DO NOT store or use gasoline or other

flammable vapors and liquids in the
vicinity of this or any other appliance.

TABLE OF CONTENTS

SECTION

DESCRIPTION PAGE

1.0) Safety........................................................................................................................................ 2

2.0) Installer Responsibility........................................................................................................... 2

3.0) General Information ............................................................................................................... 2

4.0) Minimum Clearances to Combustibles ............................................................................... 4

5.0) Specifications .......................................................................................................................... 5

6.0) Packing List ............................................................................................................................. 5

6.1) Accessory Packages ............................................................................................................... 9

7.0) Typical Layouts – PTS/U Series ........................................................................................... 11

7.1) Typical Assembly Layout........................................................................................................ 12

8.0) Dimensions – PTS Series....................................................................................................... 13

8.1) Dimensions – PTU Series ..................................................................................................... 14

8.2) Heater Assembly / Joining of Tube Sections...................................................................... 15

9.0) Typical Suspension Methods................................................................................................. 17

10.0) Assembly of Tube Sections.................................................................................................... 18

10.1) Assembly of Extension Section............................................................................................. 19

10.2) Inserting Turbulators .............................................................................................................. 20

10.3) Adding Body Reflectors.......................................................................................................... 21

11.0) Adding Optional 90º Elbow (PTS Only) ............................................................................... 22

11.1) Adding Optional Corner Reflector (PTS Only) .................................................................... 22

11.2) Adding 180º U-Bend (PTU Only)........................................................................................... 23

11.3) Adding Optional U-Bend Reflector (PTU Only) ................................................................... 23

12.0) Attaching Control Box Assembly .......................................................................................... 24

12.1) Connecting The TISS System ............................................................................................... 25

13.0) Gas Connections And Regulations ....................................................................................... 28

14.0) Instructions For Pressure Test Gauge Connection............................................................. 30

15.0) Electrical Connections............................................................................................................ 31

16.0) Venting...................................................................................................................................... 34

17.0) Air For Combustion ................................................................................................................. 38

17.1) Direct Outside Air For Combustion....................................................................................... 38

18.0) Lighting and Shutdown Instructions .................................................................................... 40

19.0) Sequence of Operation .......................................................................................................... 40

20.0) Burner Component Location ................................................................................................. 41

21.0) Cleaning And Annual Maintenance...................................................................................... 42

22.0) Troubleshooting Guide ........................................................................................................... 43

23.0) Replacing Parts ....................................................................................................................... 46

23.1) Removal of Main Burner And Electrodes ............................................................................ 46

23.2) Removing Gas Valve And Manifold Assembly ................................................................... 47

23.3) Air Switch Pressure Check .................................................................................................... 47

23.4) Ignition System Checks.......................................................................................................... 48

24.0) Installation Data...................................................................................................................... 49

25.0) Replacement Parts Guide...................................................................................................... 49

This heater complies with ANSI Z83.20 (current standard) and CSA 2.34. Copies of the National Fuel Gas Code (ANSI
Z223.1-latest edition) are available from the CSA at 8501 East Pleasant Valley Road, Cleveland, Ohio 44131 or 55 Scarsdale
Road, Don Mills, Ontario M3B 2R3. All NFPA codes are available from the National Fire Protection Association, Batterymarch
Park, Quincy, Massachusetts 02269.

Form #43343530
July 08 –1–

1.0) SAFETY

This heater is a self-contained two stage infrared radiant tube heater. Safety information required during installation
and operation of this heater is provided in this manual and the labels on the product. The installation, service and
maintenance of this heater must be performed by a contractor qualified in the installation and service of gas fired
heating equipment.

All personnel in contact with the heater must read and understand all safety information, instructions and labels
before operation. The following symbols will be used in this manual to indicate important safety information.

Warning instructions must be followed to prevent or avoid hazards which
may cause serious injury, property damage or death.

Caution instructions must be followed to prevent incorrect operation or
installation of the heater which may cause minor injury or property damage.

2.0) INSTALLER RESPONSIBILITY

The installer is responsible for the following:

• The heater and venting, as well as electrical and gas supplies must be installed in accordance with these
installation instructions and any applicable codes and regulations.

• Every heater shall be located with respect to building construction and other equipment so as to permit access to
the heater.

• Each installer must follow the clearances to combustible materials for the heaters.

• Install the heater so that the supports and hangers are correctly spaced in accordance with these instructions. The

heater must be supported by materials having a working load limit of at least 115lbs.

• Ensure that the tube integrity safety system TISS™ supplied is installed in accordance with these instructions and
that the tension is correct.

• Supply the owner with a copy of these Installation and Operation Instructions.

• Where unvented heaters are used, gravity or mechanical means shall be provided to supply and exhaust at least 4

CFM per 1,000 Btu/hr input of installed heaters.

• Never use the heater as a support for a ladder or other access equipment. Do not hang anything from the heater.

• Supply all installation materials necessary that are not included with the heater.

• Check the nameplate to make sure that the burner is correct for the gas type in the building and the installation

altitude.

3.0) GENERAL INFORMATION

This heater is a self-contained two stage infrared radiant tube heater for use in locations where flammable gases or
vapors are not generally present (as defined by OSHA acceptable limits) and is intended for the heating of
nonresidential spaces.

INSTALLATION REQUIREMENTS

The installation must conform to local building codes or in the absence of local codes, with the National Fuel Gas
Code ANSI Z223.1/NFPA54 or the Natural Gas and Propane Installation Code CSAB149.1. Heaters shall be installed
by a licensed contractor or licensed installer. Clearances to combustibles as outlined in this manual should always
be observed. In areas used for storage of combustible materials where they may be stacked below the heater,
NFPA54 requires that the installer must post signs that will “specify the maximum permissible stacking height to
maintain the required clearances from the heater to combustibles.”

Form #43343530
–2– JJuly 08

Every heater shall be located with respect to building construction and other equipment so as to permit access to the
heater. Each installer shall use quality installation practices when locating the heater and must give consideration to
clearances to combustible materials, vehicles parked below, lights, overhead doors, storage areas with stacked
materials, sprinkler heads, gas and electrical lines and any other possible obstructions or hazards. Consideration also
must be given to service accessibility.

The heater, when installed in aircraft hangars and public garages, must be installed in accordance with ANSI/NFPA
409-latest edition (Standard for Aircraft Hangars), ANSI/NFPA 88a-latest edition (Standard for Parking Structures),
and ANSI/NFPA 88b-latest edition (Standard for Repair Garages) with the following clearances:
a. At least 10 feet above the upper surfaces of wings or engine enclosures of the highest aircraft that may be

housed in the hangar and at least 8 feet above the floor in shops, offices, and other sections of hangars
communicating with aircraft storage or service areas.

b. At least 8 feet above the floor in public garages. WARNING

: Minimum clearances marked on the heater must

be maintained from vehicles parked below the heater.

a. Installation of this appliance is to be in accordance with latest edition of CAN 1-B149.1 (Installation Code for



(FOR CANADA ONLY)

Natural Gas Burning Appliances and Equipment), and/or CAN B149.2 (Installation Code for Propane Gas Burning
Appliances and Equipment).

b. For installation in public garages or aircraft hangars, the minimum clearances from the bottom of the infrared

heater to the upper surface of the highest aircraft or vehicle shall be 50 percent greater than the certified
minimum clearance, but the clearance shall not be less than 8 feet.

Although these heaters may be used in many applications other than space heating (e.g., process heating), Space­Ray will not recognize the warranty for any use other than space heating.

This heater is for Indoor Installation and Covered Patio Installation only and can be used in either Vented or Unvented
mode. The term Unvented actually means Indirect Vented. While the products of combustion are expelled into the
building, national codes require ventilation in the building to dilute these products of combustion. This ventilation
may be provided by gravity or mechanical means.

This heater is not an explosion proof heater. Where the possibility of exposure to volatile and low flash point
materials exists, it could result in property damage or death. This heater must not be installed in a spray booth where
the heater can operate during the spraying process. Consult your local fire marshal or insurance company.

PTS Series Only

: Since straight tube heaters are always hotter at the control end than at the flue terminal end,

always observe the minimum recommended mounting heights shown on the specification sheets and in Section

5.0 of this manual. Use U-tube configuration instead of straight tubes for spot or area heating (e.g., where a single

heater is utilized for space heating).

HOT

WARM

WARM

HOT

WARM

WARM

High Altitude

:

Appliances are supplied as standard for altitudes of O to 2,000 feet (0-610 m). High-altitude ratings are obtained
by a change in the orifice size. When ordered for high altitude installations, burners are supplied by the factory
ready for high altitude installation. Check the nameplate for altitude before proceeding with the installation. In
Canada the adjustment for altitude is made in accordance with Standard CGA 2.17, Gas-Fired Appliances for Use
at High Altitudes.

Form #43343530
July 08 –3–

4.0) MINIMUM CLEARANCES TO COMBUSTIBLES

Combustible material must be located outside the
clearance dimensions listed.

Failure to do so may result in death, serious injury or
property damage.

Minimum clearances to combustibles shall be measured from the outer surfaces as shown in the following diagram:

End

End

* Ceiling

Ceiling

Side

Below

Horizontal

Side

Front

Below

45° Angle (Maximum)

Rear

MINIMUM CLEARANCES TO COMBUSTIBLES

Angle Mounted at

Model No.

PTS/PTU 40/25

PTS/PTU 50/30

PTS/PTU 75/50

PTS/PTU 100/65

PTS/PTU 125/80

PTS/PTU 150/100

PTS/PTU 175/110

PTS/PTU 200/125

Mounted Horizontally

Sides Ceiling* Below Ends 45º Front 45º Rear

27” 6” 40” 30” 48” 12”
27” 6” 40” 30” 48” 12”
27” 6” 60” 30” 48” 12”
66” 6” 88” ** 40” 66” 20”
66” 6” 101” ** 40” 66” 20”
84” 6” 106” ** 48” 84” 24”
84” 6” 106” ** 48” 84” 24”
84” 6” 106” ** 48” 84” 24”

45º

* When used indirect vented, minimum clearance for CEILING must be: 12” for PTS/PTU 50-75 and 18” for
PTS/PTU 100-200. If optional corner and u-bend reflectors are not used, the clearance must be 18”.

** Maximum clearance below reduces to 72” once you are 20ft. downstream from the control box.

WARNING

: Certain materials or objects, when stored under the heater, will be subjected to radiant heat and
could be seriously damaged. Observe the Minimum Clearances to Combustibles listed in the manual and on the
heater at all times.

NOTE

: The clearances specified above must be maintained to combustibles and other materials that may be
damaged by temperatures 90ºF above ambient temperature. Clearances to combustibles are posted on the
control box. In areas used for storage of combustible materials where they may be stacked below the heater,
NFPA54 requires that the installer must post signs that will “specify the maximum permissible stacking height to
maintain the required clearances from the heater to combustibles.” Space-Ray recommends posting these signs
adjacent to the heater thermostat or other suitable location that will provide enhanced visibility.

Form #43343530
–4– JJuly 08

5.0) SPECIFICATIONS

High

Btu/hr

Model No.

PTS/PTU 40/25 40,000 25,000 #44140061 #32
PTS/PTU 50/30 50,000 30,000 #44140064 3.5mm
PTS/PTU 75/50 75,000 50,000 #44140063 #21

PTS/PTU 100/65 100,000 65,000 #44140062 #12
PTS/PTU 125/80 125,000 80,000 #44140066 #4

PTS/PTU 150/100 150,000 100,000 #44140067 “A”
PTS/PTU 175/110 175,000 110,000 #44140067 “E”
PTS/PTU 200/125 200,000 125,000 #44140068 6.9mm

Input

Low

Btu/hr

Input

Combustion

Air Plate

Part #

Natural Gas Propane Gas

Orifice Size

(0.116)

(0.138)

(0.159)

(0..189))

(0..209)

(0.234)

(0.250)

(0.272)

#49

46

2.5mm

#32
#30

#27
#23

4.1mm

(0.073)

(0.081)

(0.098)

(0.116)

(0.129)

(0.144)

(0.154)

(0.161)

Minimum *

Mounting Height

@

Horizonta

l

45º Angle

10 ft. 9 ft. 4
11 ft. 10 ft. 5
13 ft. 12 ft. 5

14 ft. 13 ft. 3
14 ft. 13 ft. 7

15 ft. 14 ft. 4
16 ft. 15 ft. 0
18 ft. 16 ft. 1

@

Turbulator

* MOUNT HEATERS AS HIGH AS POSSIBLE. Minimums are shown as a guideline for human comfort and uniform
energy distribution for complete building heating applications. Consult your Space-Ray representative for the
particulars of your installation requirements.

Type

Gas:

Natural

or Propane

Gas-Pipe

Connection:

Diameter:

Tube

Flue

Connection: 1

Fresh Air

Connection: 1

½” MPT

(Male) 4” 4” Round 4” Round

Electrical

Supply:

Current
Rating:

120 Volt,

60Hz, 1 Phase 1.74 Amp

1) See Section 16 for vent sizes when multiple heaters are connected into a common vent.

Module Electrical Rating:

Input Power-Control: 18-30 VAC 50/60 Hz (class 2
transformer)
Input Power-Line: 120 VAC (L1, IND contacts only)
Gas Valve Rating: 2.0 A @ 24 VAC (max.)
Combustion Blower Rating: 3.0 FLA @ 120 VAC

Ignition System (direct spark):

15 second trial for ignition period
15 second pre-purge period
60 second inter-purge period
30 second post-purge period

3 tries for ignition (separate flame sensor).
1/4 H.P. Motor
Flame Sensitivity: 0.7 microamps minimum

Qty.

6.0) PACKING LIST

A) PTS/PTU Burner Package QTY

Burner Box Assembly (Refer to the following chart for Package Part Numbers) 1

4”ID x 4”Lg Flue Adapter Collar (#30504500) ...................................................................1

Fastener Kit – Burner Box Attachment/Flue Adapter Collar (#42907040)....................1

containing

¼ - 20 Locknuts (#02167010)..............................................................3

Tube Flange Gasket (#42921000).......................................................................................1

Turbulator 24” Long (#44152240) *See chart above for required quantities. *

Installation & Operation Instructions (#43343530)..........................................................1

Turnbuckle (#30545040) ......................................................................................................1

Gas connector 5/8” OD x 36” (#30302360) .......................................................................1

Form #43343530
July 08 –5–

: #10 x 1/2” Self-Drilling Screws (#02189020)..............................2

BURNER PACKAGE NUMBERS:

NATURAL GAS PROPANE GAS

MODEL NO PART NO.
PTS/U 40-N7 #44149510
PTS/U 50-N7 #44149530
PTS/U 75-N7 #44149550
PTS/U 100-N7 #44149570
PTS/U 125-N7 #44149590
PTS/U 150-N7 #44149610
PTS/U 175-N7 #44149630
PTS/U 200-N7 #44149650

MODEL NO

PART NO.

PTS/U 40-L7 #44149520
PTS/U 50-L7 #44149540
PTS/U 75-L7 #44149560
PTS/U 100-L7 #44149580
PTS/U 125-L7 #44149600
PTS/U 150-L7 #44149620
PTS/U 175-L7 #44149640
PTS/U 200-L7 #44149660

B) PTS 40-200 Body Package Descriptions

(Package Part Number is indicated on the outside of each corresponding carton.)

System Lengths

PTS Body Packages – Aluminized/Hot Rolled or

Alumi-Therm/Hot Rolled

10 Ft.

44134020

20 Ft. pkg

44135000

30 Ft. pkg

44136000

40 Ft. pkg

44137100

50 Ft. pkg

44138100

Part # Each Body Package Includes: Qty. Qty. Qty. Qty. Qty.

42912080 10 Ft. Tube with 24 Hole Flange (Aluminized) 1 1 1 - ­42912169 10 Ft. Tube with 6 Hole Flange (Alumi-Therm) - - - 1 1
41932101 10 Ft. Tube less Flanges (Hot Rolled) - 1 2 3 4
43319100 Reflector, 9’ 11½” 1 2 3 4 5
30462980 Tube Coupling - 1 2 3 4
43318000 Tube Hanger/Support Bracket, 13” 1 2 3 4 5
43980010 Wire Hanger 1 2 3 4 5

Body Fastener Kit (included in body packages) 42907280 42907190 42907200 42907210 42907220
42873000 U-Bolt 1 2 3 4 5
02127110 Hex Nut, 5/16-18 3 5 6 8 10
02189020 HWHSM Screw, #10-16 x ½” TEKS 4 8 10 14 18

60Ft. System 70Ft. System

PTS Body Packages – Alumi-Therm/Hot Rolled

40 Ft. Pkg

44137100

20 Ft. Pkg

44135010

40 Ft. Pkg.

44137100

30 Ft. Pkg

44136040

Part # Each Body Package Includes: Qty. Qty. Qty. Qty.

42912169 10 Ft. Tube with 6 Hole Flange (Alumi-Therm)

1 - 1 ­41932101 10 Ft. Tube less Flanges (Hot Rolled) 3 2 3 3
43319100 Reflector, 9’ 11½” 4 2 4 3
30462980 Tube Coupling 3 2 3 3
43318000 Tube Hanger/Support Bracket, 13” 4 2 4 3
43980010 Wire Hanger 4 2

4 3

Body Fastener Kit (included in body packages) 42907210 42907190 42907210 42907200
42873000 U-Bolt 4 2 4 3
02127110 Hex Nut, 5/16-18 8 5 8 6
02189020 HWHSM Screw, #10-16 x ½” TEKS 14 8

14 10

Form #43343530
–6– JJuly 08

C) PTS 40-200 Series Body Package Descriptions – ALC Option (Aluminized Calorized)

(Package Part Number is indicated on the outside of carton.)

System Lengths

PTS Body Packages – Aluminized/Aluminized or

Alumi-Therm/Aluminized

10 Ft. Pkg

44134020

20 Ft. Pkg

44135020

30 Ft. Pkg

44136020

40 Ft. Pkg

44137090

50 Ft. Pkg

44138080

Part # Each Body Package Includes: Qty. Qty. Qty. Qty. Qty.

42912080 10 Ft. Tube with 24 Hole Flange (Aluminized) 1 1 1 - ­42912169 10 Ft. Tube with 6 Hole Flange (Alumi-Therm) - - - 1 1
41932100 10 Ft. Tube less Flanges (Aluminized) - 1 2 3 4
43319100 Reflector, 9’ 11½” 1 2 3 4 5
30462980 Tube Coupling - 1 2 3 4
43318000 Tube Hanger/Support Bracket, 13” 1 2 3 4 5
43980010 Wire Hanger 1 2 3 4 5

Body Fastener Kit (included in body packages) 42907280 42907190 42907200 42907210 42907220
42873000 U-Bolt 1 2 3 4 5
02127110 Hex Nut, 5/16-18 3 5 6 8 10
02189020 HWHSM Screw, #10-16 x ½” TEKS 4 8 10 14 18

60Ft. System 70Ft. System

PTS Body Packages – Alumi-Therm/Aluminized

40 Ft. Pkg

44137090

20 Ft. Pkg

44135030

40 Ft. Pkg

44137090

30 Ft. Pkg

44136050

Part # Each Body Package Includes: Qty. Qty.

42912169 10 Ft. Tube with 6 Hole Flange (Alumi-Therm)

1 - 1 -

Qty. Qty.

41932100 10 Ft. Tube less Flanges (Aluminized) 3 2 3 3
43319100 Reflector, 9’ 11½” 4 2 4 3
30462980 Tube Coupling 3 1 3 3
43318000 Tube Hanger/Support Bracket, 13” 4 2 4 3
43980010 Wire Hanger 4 2

4 3

Body Fastener Kit (included in body packages) 42907210 42907190 42907210 42907200
42873000 U-Bolt 4 2 4 3
02127110 Hex Nut, 5/16-18 8 5 8 6
02189020 HWHSM Screw, #10-16 x ½” TEKS 14 8

14 10

D) PTU 40-200 Body Package Descriptions

(Package Part Number is indicated on the outside of each corresponding carton.)

System Lengths

PTU Body Packages – Aluminized/Hot Rolled or

Alumi-Therm/Hot Rolled

20 Ft. Pkg.

44135000

30 Ft. Pkg

44136010

40 Ft. Pkg

44137100

50 Ft. Pkg

44138110

Part # Each Body Package Includes: Qty. Qty. Qty. Qty.

42912080 10 Ft. Tube with 24 Hole Flange (Aluminized) 1 1 - ­42912169 10 Ft. Tube with 6 Hole Flange (Alumi-Therm) - - 1 1
41932101 10 Ft. Tube less Flanges (Hot Rolled) 1 1 3 3
41932051 5 Ft. Tube less Flanges (Hot Rolled) - 2 - 2
43319100 Reflector, 9’ 11½” 2 2 4 4
43319050 Reflector, 4’ 11 ½” - 2 - 2
30462980 Tube Coupling 1 3 3 5
43318000 Tube Hanger/Support Bracket, 13” 2 4 4 6
43980010 Wire Hanger 2 4 4 6

Form #43343530
July 08 –7–

Body Fastener Kit (included in body packages) 42907190 42907210 42907210 42907221

42873000 U-Bolt 2 4 4 6
02127110 Hex Nut, 5/16-18 5 8 8 13
02189020 HWHSM Screw, #10-16 x ½” TEKS 8 14 14 24

U-Bend Package 43208020 43208020 43208020 43208020
42873000 U-Bend 1 1 1 1
43318500 31” Tube Support/Hanger Bracket 1 1 1 1
30462980 Tube Coupling 1 1 1 1
02189020 HWHSM Screw, #10-16 x ½” TEKS 2 2 2 2

60Ft. System 70Ft. System

PTU Body Packages – Alumi-Therm/Hot Rolled

40 Ft. Pkg.

44137100

20 Ft. Pkg.
44135010

40 Ft. Pkg.

44137120

30 Ft. Pkg.

44136040

Part # Each Body Package Includes: Qty. Qty. Qty. Qty.

42912169 10 Ft. Tube with 6 Hole Flange (Alumi-Therm)

1 - 1 ­41932101 10 Ft. Tube less Flanges (Hot Rolled) 3 2 2 3
41932051 5 Ft. Tube less Flanges (Hot Rolled) - - 2 ­43319100 Reflector, 9’ 11½” 4 2 3 3
43319050 Reflector, 4’ 11 ½’ - - 2 ­30462980 Tube Coupling 3 2 4 3
43318000 Tube Hanger/Support Bracket, 13” 4 2 5 3
43980010 Wire Hanger 4 2

5 3

Body Fastener Kit (included in body packages) 42907210 42907219 42907220 42907200
42873000 U-Bolt 4 2 5 3
02127110 Hex Nut, 5/16-18 8 5 10 6
02189020 HWHSM Screw, #10-16 x ½” TEKS 14 8

18 10

U-Bend Package 43208020 43208020
42873000 U-Bend 1 1
43318500 31” Tube Support/Hanger Bracket 1 1
30462980 Tube Coupling 1 1
02189020 HWHSM Screw, #10-16 x ½” TEKS 2

2

E) PTU 40-200 Series Body Package Descriptions – ALC Option (Aluminized Calorized)

(Package Part Number is indicated on the outside of each corresponding carton.)

System Lengths

PTU Body Packages –Aluminized/Aluminized or

Alumi-Therm/Aluminized

20 Ft. Pkg.

44135020

30 Ft. Pkg.

44136030

40 Ft. Pkg.

44137090

50 Ft. Pkg.

44138090

Part # Each Body Package Includes: Qty. Qty. Qty. Qty.

42912080 10 Ft. Tube with 24 Hole Flange (Aluminized) 1 1 - ­42912169 10 Ft. Tube with 6 Hole Flange (Alumi-Therm) - - 1 1
41932100 10 Ft. Tube less Flanges (Aluminized) 1 1 3 3
41932050 5 Ft. Tube less Flanges (Aluminized) - 2 - 2
43319100 Reflector, 9’ 11½” 2 2 4 4
43319050 Reflector, 4’ 11 ½” - 2 - 2
30462980 Tube Coupling 1 3 3 5
43318000 Tube Hanger/Support Bracket, 13” 2 4 4 6
43980010 Wire Hanger 2 4 4 6

Form #43343530
–8– JJuly 08

13

(33cm)

13

(33cm)

6

(15cm)

12

(30cm)

END REFLECTOR

Body Fastener Kit (included in body packages) 42907190 42907210 42907210 42907221
42873000 U-Bolt 2 4 4 6
02127110 Hex Nut, 5/16-18 5 8 8 13
02189020 HWHSM Screw, #10-16 x ½” TEKS 8 14 14 24

U-Bend Package 43208020 43208020 43208020 43208020
42873000 U-Bend 1 1 1 1
43318500 31” Tube Support/Hanger Bracket 1 1 1 1
30462980 Tube Coupling 1 1 1 1
02189020 HWHSM Screw, #10-16 x ½” TEKS 2 2 2 2



60Ft. System 70Ft. System

PTU Body Packages – Alumi-Therm/Aluminized

40 Ft. Pkg.

44137090

20 Ft. Pkg.

44135030

40 Ft. Pkg.

44137110

30 Ft. Pkg.

44136050

Part # Each Body Package Includes: Qty. Qty. Qty. Qty.

42912169 10 Ft. Tube with 6 Hole Flange (Alumi-Therm) 1 - 1 ­41932100 10 Ft. Tube less Flanges (Aluminized) 3 2 2 3
41932050 5 Ft. Tube less Flanges (Aluminized) - - 2 ­43319100 Reflector, 9’ 11½” 4 2 3 3
43319050 Reflector, 4’ 11 ½’ - - 2 ­30462980 Tube Coupling 3 2 4 3
43318000 Tube Hanger/Support Bracket, 13” 4 2 5 3
43980010 Wire Hanger 4 2

5 3

Body Fastener Kit (included in body packages) 42907210 42907219 42907220 42907200
42873000 U-Bolt 4 2 5 3
02127110 Hex Nut, 5/16-18 8 5 10 6
02189020 HWHSM Screw, #10-16 x ½” TEKS 14 8

18 10

U-Bend Package 43208020 43208020
42873000 U-Bend 1 1
43318500 31” Tube Support/Hanger Bracket 1 1
30462980 Tube Coupling 1 1
02189020 HWHSM Screw, #10-16 x ½” TEKS 2

2

6.1) ACCESSORIES

A) End Reflector Accessory Package, Part #43341010

(1 pkg. per PTS Series or 2 pkgs. per PTU Series)

Contains
End Reflector, #43320000……QTY–2
Speed Clips, #02266010……QTY–4

B) Elbow Accessory Package, Part #43208010

Form #43343530
July 08 –9–

(Option for PTS Series Only)

Contains

Elbow, #431750010……QTY–1
#10-16 x ½ Self-Drilling Screws, #02189020……QTY–2
Tube Coupling, #30462980……QTY–1

:

:

18

(46cm)

30 3/4 (78cm)

Length = 24 (61cm)

C) Corner Reflector Accessory Package, Part #43342000

(Option for PTS Series Only)

Contains

:

Corner Reflector Assembly, #43345000……QTY–1

Speed Clips, #02266010……QTY–4

24

(61cm)

D) U-Bend Package, Part #43208020

(Option for PTU Series Only)

Contains:

U-Bend, #42913020……QTY–1
#10-16 x ½ Self-Drilling Screws, #02189020……QTY–2
Tube Coupling, #30462980……QTY–1
31” Hanger/Tube Support, #43318500……QTY–1

E) U-Bend Reflector Package, Part #43488000

(Option for PTU Series Only)

Contains:
U-Bend Reflector, #43490000……QTY–1
U-Bend End Reflector, #43490050……QTY–1
Speed Clips, #02266010……QTY–11

#10-16 x ½ Self-Drilling Screws, #02189020……QTY–4

F) 31” Hanger/Tube Support, Part #43318500

(Option for Angle Mounting of PTU Series)

31

(79cm)

18

(46cm)

Tube Centers

G) Exhaust Hood Package, Part #42924000

Contains

Exhaust Hood Assembly, #42925540……QTY–1
#10-16 x ½ Self-Drilling Screws, #02189020……QTY–2

:

4 (10cm)

7 1/2
(19cm)

3 3/4 (10cm)

3 1/2 (9cm)

Side View

24

(61cm)

7 1/2
(19cm)

Bird
Screen

Front View

Form #43343530
–10– JJuly 08

7.0) TYPICAL LAYOUTS – PTU / PTS Series

10FT.
SYSTEM

50 FT.
SYSTEM

20 FT.
SYSTEM

30 FT.
SYSTEM

60 FT.
SYSTEM

40 FT.
SYSTEM

LEGEND

Burner Box

Flue Termination

10 FT. Body Section

5 FT. Body Section

90 Deg. Elbow

180 Deg. U-Bend

70 FT.
SYSTEM

EMITTER LENGTH BODY LENGTH

MODEL

PTS 40/25

PTS 50/30

PTS 75/50

PTS 100/65

PTS 125/80

PTS 150/100

PTS 175/110

PTS 200/125

Min. Max.

10 Ft. 20 Ft.

20 Ft 30 Ft.

20 Ft. 30 Ft.

30 Ft. 40 Ft.

30 Ft 50 Ft.

40 Ft. 60 Ft.

50 Ft. 70 Ft.

50 Ft. 70 Ft.

MODEL

PTU 40/25

PTU 50/30

PTU 75/50

PTU 100/65

PTU 125/80

PTU 150/100

PTU 175/110

PTU 200/125

Min. Max.

10 Ft. 10 Ft.

10 Ft. 15 Ft.

10 Ft. 15 Ft

15 Ft. 20 Ft.

15 Ft. 25 Ft.

20 Ft. 30 Ft.

25 Ft. 35 Ft.

25 Ft. 35 Ft.

NOTES:

1) In all configurations, the control unit must be connected directly to either a) the 24-hole flange of the 10 ft.
aluminized steel starting body section (for 10 ft., 20 ft., and 30 ft. systems) or b) the 6-hole flange of the 10 ft.
alumi-therm steel starting body section (for 40 ft., 50 ft., 60 ft., and 70 ft. systems.

2) Joining of two 90º elbows directly together to form a “Z” shape IS NOT permitted.

3) PTS / U 175/110 - 40 ft length available for special applications.

4) 5 Ft. Body Packages may be utilized on any of these heaters to yield heater lengths from 15 ft. to 70 ft.

5) Any configuration of components not shown in the illustrations may be used except as noted in 1 and 2

Form #43343530
July 08 –11–

above.

7.1) TYPICAL ASSEMBLY LAYOUT

POISONOUS GAS AND SOOT HAZARD

The heater must be assembled with the correct number of turbulator sections
and tube length for the rated heat input.

The turbulator must be installed in the last tube section as shown.

Failure to do so may result in death, serious injury, property damage or illness
from Carbon Monoxide poisoning.

10 FT. SYSTEM

20 FT. SYSTEM

30 FT. SYSTEM

40 FT. SYSTEM

50 FT. SYSTEM

60 FT. SYSTEM

70 FT. SYSTEM

Burner Box 10ft Aluminized Tube 24

Form #43343530
–12– JJuly 08

Stainless Steel Turbulator
closest to burner PTS / U
40 only.

Hole Flange

or
10ft Alumi-Therm Tube
6 Hole Flange

LEGEND

Coupling 10ft Aluminized or HRS

Tube model dependent

MODEL

PTS/U 40/25
PTS/U 50/30
PTS/U 75/50
PTS/U 100/65
PTS/U 125/80
PTS/U 150/100
PTS/U 175/110
PTS/U 200/125

2ft Stainless
Steel
Turbulator
sections

2 Ft. Turbulator

Sections

2ft Aluminized
Steel
Turbulator
sections

4
5
5
3
7
4
0
1

8.0) DIMENSIONS – PTS Series

Typical Dimensions Up to 60 Ft. Shown.

120VAC

Power Supply Cord

10

(25cm)

Fresh Air

Inlet

1/2 MPT Gas

(37cm)

14-1/2

Connection

9-1/4

(24cm)

Burner

Box

End View

Flue Terminal

12

(30cm)

108

(274cm)

12

12

(30cm)

(30cm)

108

108

(274cm)

(274cm)

12

12

(30cm)

(30cm)

108

108

108

(274cm)

(274cm)

(274cm)

Wire Hanger

13 Tube Support/

Hanger Bracket

Wire Hanger

13 Tube Support/

Hanger Bracket

Wire Hanger

13 Tube Support/

Hanger Bracket

Wire Hanger

10 FT Tube

Assembly

120

(typical)

14

(305cm)

108

(274cm)

(36cm)

Models:

PTS 40

Flue

Terminal

Burner

Box

12

(30cm)

240

(610cm)

14

108

(274cm)

108

(274cm)

(36cm)

Models:

PTS 40, 50,

75

12

12

(30cm)

360

(30cm)

108

(274cm)

108

(274cm)

(914cm)

108

(274cm)

Models:

12

12

PTS 50, 75,

100, 125

(30cm)

480

(30cm)

108

(274cm)

(1219cm)

108

(274cm)

108

(274cm)

Models:

PTS 100, 125

150

108

4 Tube Coupling

(typical)

12

(30cm)

600

(1524cm)

108

12

(30cm)

108

(274cm)

(274cm)

(274cm)

Models:

PTS 125, 150,

175, 200

4 Tube Coupling

(typical)

12

(30cm)

720

12

(30cm)

Bottom View

108

(274cm)

(1829cm)

108

(274cm)

108

(274cm)

Models:

PTS 150, 175,

200

13 Tube Support/

Wire Hanger

13 Tube Support/

Wire Hanger

Bottom View

13 Tube Support/

Hanger Bracket

Hanger Bracket

Hanger Bracket

Form #43343530
July 08 –13–

8.1) DIMENSIONS – PTU Series

Typical Dimensions Up to 50 Ft. Shown.

(36cm)

Models:
PTU 40, 50,
75

Models:
PTU 50, 75,
100, 125

Models:
PTU 100, 125,
150, 175

Models:
PTU 125, 150,
175, 200

14

Burner
Box

Flue
Terminal

(274cm)

(305cm)

108

180

(457cm)

(274cm)

108

(274cm)

120

108

(274cm)

108

240

(610cm)

12

(30cm)

12

(30cm)

12

(30cm)

15

(38cm)

10 FT Tube
Assembly
(typical)

48

(122cm)

300

(762cm)

5 FT Tube
Assembly

108

(274cm)

(274cm)

108

U-Bend

12

(30cm)

(122cm)

4 Tube Coupling
(typical)

48

6

(16cm)

31 Tube Support/
Hanger Bracket

Bottom View

31 Tube Support/
Hanger Brackets
(typical at control end)

Shipped with
U-Bend Package

Flue Terminal

Wire Hangers
(typical)

1/2 MPT Gas
Connection

18 (46cm)

31 (79cm)

PTU (end view)

13 Tube Support/
Hanger Brackets
(typical)

Fresh Air
Inlet

U-Bend

10

(25cm)

Wire Hangers
(typical)

120VAC
Power Supply Cord

Burner
Box

13 Tube Support/
Hanger Brackets
(typical)

14-1/2
(37cm)

Form #43343530
–14– JJuly 08

8.2) HEATER ASSEMBLY / JOINING OF TUBE SECTIONS

a

Flue

Termin

Turbulator

(See specifications

section 5 for required

quantities.)

Typical

Overlap

Not Less

Than 10

#10 Self-Drill Screws

(Typical all tube supports,

tube couplings and flue

terminal.)

Wire Hanger

Tube Support Bracket

Tube Coupling

)

.

8 - 10

(Typical each tube joint

8 - 10

5 hanging points to be used for suspension for a typical 40ft

long system. There must be two hanging points on the first

tube and one on each of the other tubes

U-Bolt Clamp &

5/16" Hex Nuts

Tube

7

8 - 9 ¼

4"OD x 10Ft.

for required tubes.

See section

Flange

24 Hole for Aluminized Steel Tubes

6 Hole for Alumi-Therm Steel Tubes

Mounting

Gasket

(PTS 40FT Shown)

Burner

Box

Maximum 6 distance

from burner box to the

Typical Assembly Overview

tube support/hanger

Burner Box

bracket.

Suspension

Chain

Form #43343530
July 08 –15–