Gasboy MS7120 User Manual

Introduction

Purpose

This document contains a verification sequence that allows you to determine whether your
scanner is configured correctly, and a programming sequence to follow if it is not configured
correctly.

Be aware of the following:

Metrologic® MS7120 Bar Code Scanner Setup

January 2007

IMPORTANT INFORMATION

• Refer to MDE-4389 Setting Up Datalogic™ DLL2020 Bar Code Scanner Used on
Profit Point Terminal for Datalogic DLL2020 scanners.

• Refer to MDE-4354 Setting Up Metrologic
Metrologic MS6720 scanners.

®

MS6720 Bar Code Scanner for

MDE-4631

Note: Your bar code scanner has been programmed with default settings at the factory and

Table of Contents

Top ic Page

Introduction 1

Important Safety Information 3

Setting Up the Scanner 5

Programming a Sequence 7

Bar Codes 8

should be ready to be configured.

MDE-4631 Metrologic® MS7120 Bar Code Scanner Setup · January 2007 Page 1

Introduction

Warranty

For information on warranty, refer to MDE-4255 Gasboy’s Warranty Policy Statement. If you
have any warranty-related questions, contact Gasboy’s Warranty Department at its Greensboro
location.

Page 2 MDE-4631 Metrologic® MS7120 Bar Code Scanner Setup · January 2007

Important Safety Information

This section introduces the hazards and safety precautions
associated with installing, inspecting, maintaining or servicing
this product. Before performing any task on this product, read
this safety information and the applicable sections in this
manual, where additional hazards and safety precautions for
your task will be found. Fire, explosion, electrical shock or
pressure release could occur and cause death or serious
injury if these safe service procedures are not followed.

Preliminary Precautions

You are working in a potentially dangerous environment of
flammable fuels, vapors, and high voltage or pressures. Only
trained or authorized individuals knowledgeable in the related
procedures should install, inspect, maintain or service this
equipment.

Important Safety Information

Read the Manual

Read, understand and follow this manual and any other
labels or related materials supplied with this equipment. If you
do not understand a procedure, call a Gasboy Authorized
Service Contractor or call the Gasboy Service Center at 1­800-444-5529. It is imperative to your safety and the safety of
others to understand the procedures before beginning work.

Follow the Regulations

There is applicable information in NFPA 30A; Automotive and
Marine Service Code, NFPA 70; National Electrical Code (NEC),

OSHA regulations and federal, state, and local codes which
must be followed. Failure to install, inspect, maintain or
service this equipment in accordance with these codes,
regulations and standards may lead to legal citations with
penalties or affect the safe use and operation of the
equipment.

Emergency Total Electrical Shut-Off

The first and most important information you must know is
how to stop all fuel flow to the pump and island. Locate the
switch or circuit breakers that shut-off all power to all fueling
equipment, dispensing devices, and submerged turbine
pumps (STPs).

!

WARNING

!

The EMERGENCY STOP, ALL STOP, and
PUMP STOP buttons at the cashier’s station
WILL NOT shut off electrical power to the
pump/dispenser.

Total Electrical Shut-Off Before Access

Any procedure requiring access to electrical components or
the electronics of the dispenser requires total electrical shut­off of that unit. Know the function and location of this switch
or circuit breaker before inspecting, installing, maintaining, or
servicing Gasboy equipment.

Evacuation, Barricading and Shut-Off

Any procedures requiring accessing the pump/dispenser or
STPs requires the following three actions:

This means that even if you activate these
stops, fuel may continue to flow uncontrolled.

You must use the TOTAL ELECTRICAL SHUT­OFF in the case of an emergency and not only
these cashier station “stops.”

Replacement Parts

Use only genuine Gasboy replacement parts and retrofit kits
on your pump/dispenser. Using parts other than genuine
Gasboy replacement parts could create a safety hazard and
violate local regulations.

Safety Symbols and Warning Words

This section provides important information about warning
symbols and boxes.
Alert Symbol

This safety alert symbol is used in this manual and on
warning labels to alert you to a precaution which must be
followed to prevent potential personal safety hazards. Obey
safety directives that follow this symbol to avoid possible
injury or death.

Signal Words

These signal words used in this manual and on warning labels
tell you the seriousness of particular safety hazards. The
precautions that follow must be followed to prevent death,
injury or damage to the equipment

DANGER - This signal word is used to alert you to a

!

hazard to unsafe practice which will result in death or
serious injury
WARNING - This alerts you to a hazard or unsafe

!

practice that could result in death or serious injury.
CAUTION with Alert symbol - This signal word

!

designates a hazard or unsafe practice which may
result in minor injury.
CAUTION without Alert symbol - When used by itself,
CAUTION designates a hazard or unsafe practice
which may result in property or equipment damage.

- An evacuation of all unauthorized persons and vehicles
using safety tape, cones or barricades to the effected units

- A total electrical shut-off of that unit

MDE-4631 Metrologic® MS7120 Bar Code Scanner Setup · January 2007 Page 3

Working With Fuels and Electrical Energy

Prevent Explosions and Fires

Fuels and their vapors will become explosive if ignited. Spilled
or leaking fuels cause vapors. Even filling customer tanks will
cause explosive vapors in the vicinity of dispenser or island.

Important Safety Information

No Open Flames

Open flames from matches, lighters, welding
torches or other sources can ignite fuels and their vapors.

No Sparks - No Smoking

Sparks from starting vehicles, starting or using power tools,
burning cigarettes, cigars or pipes can also ignite fuels and
their vapors. Static electricity, including an electrostatic
charge on your body, can cause a spark sufficient to ignite
fuels and their vapors. After getting out of a vehicle, touch the
metal of your vehicle to discharge any electrostatic charge
before you approach the dispenser island.

Working Alone

It is highly recommended that someone who is capable of
rendering first aid be present during servicing. Be familiar
with Cardiopulmonary Resuscitation (CPR) methods if you
are working with or around high voltages. This information is
available from the American Red Cross. Always advise the
station personnel about where you will be working, and
caution them not to activate power while you are working on
the equipment. Use the OSHA tag out and lock out
procedures. If you are not familiar with this requirement, refer
to information in the service manual and OSHA
documentation.

Working With Electricity Safely

Be sure to use safe and established practices in working with
electrical devices. Poorly wired devices may cause a fire,
explosion or electrical shock. Be sure grounding connections
are properly made. Make sure that sealing devices and
compounds are in place. Be sure not to pinch wires when
replacing covers. Follow OSHA Lock-Out and Tag-Out
requirements. Station employees and service contractors
need to understand and comply with this program completely
to ensure safety while the equipment is down.

Hazardous Materials

Some materials present inside electronic enclosures may
present a health hazard if not handled correctly. Be sure to
clean hands after handling equipment. Do not place any
equipment in mouth.

!

WARNING

This area contains a chemical known to the State of
California to cause cancer.

WARNING

!

This area contains a chemical known to the State of
California to cause birth defects or other reproductive
harm.

IMPORTANT: Oxygen may be needed at scene if gasoline
has been ingested or inhaled. Seek medical advice
immediately.

Emergency First Aid

Informing Emergency Personnel

• Compile the following information for emergency
personnel:

• Location of accident (for example, address, front/back of
building, and so on.)

• Nature of accident (for example, possible heart attack, run
over by car, burns, and so on.)

• Age of victim (for example, baby, teenager, middle-age,
elderly.)

• Whether or not victim has received first aid (for example,
stopped bleeding by pressure, and so on.)

• Whether or not a victim has vomited (for example, if
swallowed or inhaled something, and so on.)

WARNING

!

Gasoline ingested may cause unconsciousness
and burns to internal organs.
Do not induce vomiting.
Keep airway open.
Oxygen may be needed at scene.
Seek medical advice immediately.

WARNING

!

Gasoline inhaled may cause unconsciousness
and burns to lips, mouth and lungs.
Keep airway open.
Seek medical advice immediately.

WARNING

!

Gasoline spilled in eyes may cause burns to eye
tissue.
Irrigate eyes with water for approximately 15
minutes.
Seek medical advice immediately

WARNING

!

Gasoline spilled on skin may cause burns.
Wash area thoroughly with clear/water.
Seek medical advice immediately.

IMPORTANT: Oxygen may be needed at scene if gasoline
has been ingested or inhaled. Seek medical advice
immediately.

Lockout/Tagout

Lockout/Tagout covers servicing and maintenance of
machines and equipment in which the unexpected
energization or start up of the machine(s) or equipment or
release of stored energy could cause injury to employees or
personnel. Lockout/Tagout applies to all mechanical,
hydraulic, chemical or other energy, but does not cover
electrical hazards. Reference Subpart S of 29 CFR Part 1910

- Electrical Hazards, 29 CFR Part 1910.333 contains specific
Lockout/Tagout provision for electrical hazards.

Page 4 MDE-4631 Metrologic® MS7120 Bar Code Scanner Setup · January 2007

Setting Up the Scanner

To set up the scanner, proceed as follows:

1 Turn off power to the Profit Point Point of Sale (POS) terminal.

2 Unplug the AC power to the POS Distribution Box (D-Box) power supply.

3 Remove the scanner and the Metrologic cable from the shipping box.

Note: None of the other parts in the shipping box, including the scanner power transformer,

will be used with this installation.

4 Insert the phone jack end of the scanner cable into the phone jack connector on the scanner

Figure 1 on page 6).

(

5 Connect the DB9 connector on the scanner cable to the scanner port on the POS D-Box

Figure 1 on page 6).

(

6 Plug in the POS D-Box power supply to the AC outlet (Figure 1 on page 6).

Setting Up the Scanner

7 Turn on the Profit Point POS terminal. Follow the instructions that appear on the screen. The

Profit Point terminal initializes and begins the POS operations.

MDE-4631 Metrologic® MS7120 Bar Code Scanner Setup · January 2007 Page 5