Garudan GP-514-446, GP-514-4467, GP-514-146(7), GP-514-146(7)i User Manual And Spare Parts List

User manual and
Spare Parts List

GP-514- 446(7)

ANITA B, s.r.o.
Hliníky 2068
680 01 Boskovice
Czech Republic
tel: [phone]
fax: [phone]

e-mail: [e-mail]

www.garudan.cz

2

www.garudan.cz

3

anita-b



GP-514-446(7)

1 Safety Measures

Do not put the machine into operation until an appropriate preparation is carried out by
a specialist or an authorised person, and until you get acquainted with safety measures.

1. Any sewing machine may be operated only by a properly trained operator.

2. Take into consideration the safety regulations valid in your country.

3. The sewing machine may be used only for the operations for which it has been.designed.
Other operations are inadmissible.

4. All safety measures must be observed on the machine before puttíng into operation and
during operation.

5. It is advisable to wear protective glasses to ensure personal safety when working on the
machine.

6. If you are going to make any modifications or changes on the machine observe the safety
regulations. Modifications can only be made at your own risk.

7. The main switch of the machine must be switched off or the plug must be pulled out of the
socket of mains supply when following operations are to be performed (if you us
mechanically controlled clutch motors without a fuse preventing the machine from being
started with the pedal wait until the motor stops).

7.1 Threading the needle thread (threads), threading the looper thread, etc.

7.2 Replacing needles,presser foot; stitch plate, looper, looper bobbin,feed dog, needle guard,
finger guard, cloth guide, etc.

7.3 When you leave the workplace and.when you leave the machine unattended.

7.4 Machine maintenance (cleaning).

8. Repairs, maintenance and modifications of the machine (see point 6) may be carried out only
by a specialist or an authorised person. Only spare parts supplied by the machine builder
should be used for repairs.

9. Works on the electrical parts of the machine can only be carried out by an electrician or under
an authorised person's control and supervision.

10. Working on "live" parts and equipment is inadmissible.

11. Compressed air supply has to be disconnected before maintenance and repairs of pneumatic
devices. Residual compressed air has to be let off before the works can be done.

12. The user will be held responsible if safety measures given in the Instructions for Use are no
observed.

13. An inseparable part of the Instructions for Use is the Instruction for use of the respective
drive

which must be observed, as well. In particular point 3 "Safety Instructions".

www.garudan.cz

4

anita-b



GP-514-446(7)

2 Putting the machine into operation

Following instructions must be observed to avoid risk of failures or damage to the

machine:

- clean the machine of preserving agents

- drop 1-2 drops of oil into looper

- remove the front cover and oil the ends of needle bar connecting-rod and of the cross-head
slide of thread take-up.

- a specialist shall check if the electrical equipment is in good order incl. necessary voltage
for motor and see to it that machine hand wheel rotates towards the operator (see arrow)
when the electric motor is connected.

-do not run the machine at full speed during the first two weeks, sewing should be performed
at ca. 3/4 of the maximum speed.

Caution!

Do not interfere with the electric equipment of the machine, call an electrician. Danger of
electrical accident. When working on the machine or close to the machine take care that
you do not give cause to an accident. See to it that no liquid can get into the electrical
equipment and cause a short-circuit or any other failure of the electrical equipment.
Observe the generally valid safety regulations.
When running the machine, be very cautious especially near the needle, trimming knives,
thread take-up and cloth pressing elements.
When the machine head is tilted on its support, take special care so that the whole machine
and support may not tilt over.
To tilt the machine into working position take the head with both hands to avoid any injury
between the tilted machine and the base plate.

www.garudan.cz

5

anita-b



GP-514-446(7)

3 Threading the Upper Thread

Caution!

Switch off the main switch and remove your feet from the pedals on the machine support before
threading so that the machine may not be started by unintended treading on the pedal.

When threading the thread from bobbin stand into needle follow figure 1 for single needle
machine, or figure 2 for two-needle machine. The threads pass from bobbin stand to thread
guides on the machine head (A, B) through auxiliary tensioner and thread guide (C), through
tensioner (D), tension spring (E) and thread take-up lever to the needle. The thread enters the
eye from the side with a long groove. On two-needle machines threading should be carried out
according to figure 2 following the arrows (P and S).

Fig.2

www.garudan.cz

6

anita-b



GP-514-446(7)

4 Inserting needles

Caution !

Switch off the main switch and remove your feet from the pedals on the machine support
before replacing needles so that the machine may not be started by unintended treading on
the pedal.

Fig.3

Having chosen the right thickness (size) of needle whose system coresponds to the prescribed
kind (usually 134 LR) loosen screw (A,fig.3) on needle bar and insert needle (B) as far as it will
go, i.e. up to the bottom of the needle hole in the needle bar. Turn the needle so that the recess
above the needle eye facs the looper point. Caution – when a greater needle size has ben chosen
it is necessary to check if the looper point does not catch the needle – a possible adjustment of
looper position must be carried out by an autorised person. Make sure that the needle passes
through the middle of the stitch plate opening. If it is not the case, check up if the needle is not
bent. Replace the defective needle.

5 Replacing Hook Bobbin, Threading Hook Thread

The thread passes from the bobbin case (A) through slot (B) under spring (C) into the looper
(fig. 4) in such a way that the thread will be unwound from the bobbin in the direction of the
arrow. Hold a thread end of ca. 5-6 cm and insert the bobbin case containing bobbin into the
hook in such a way so that the thread can be unwound from the bobbin smoothly. Lock the
bobbin case (A) in the looper using the lock (E).

Fig.4 Fig.5

Use screw (fig. 5) to adjust fhe tension of the thread unwound from the bobbin. Turn it in the
(+) direction to increase the thread tension or in the (-) direction to decrease the tension.

www.garudan.cz

7

anita-b



GP-514-446(7)

Caution!

Do not start the machine until you put the hook covers in working (protecting) position.
Switch off the main switch and remove your feet from the pedals on the machine support before
replacing the hook bobbin so that the machine may not be started by unintended treading on the
pedal.

6 Adjusting Stitch Length

Caution!

Switch off the main switch and remove your feet from the pedals on the machine support
before adjusting stitch length so that the machine may not be started by unintended treading
on the pedal.

Push in the stitch length adjusting knob (A) in the column of the machine arm (fig. 6) and turn
the hand wheel until the knob locks deeper into the arm. Turn the knob in the direction of arrow
(+) to increase the stitch length or in the direction of arrow (-) to reduce the stitch length.
Adjustment is determined by the position of the tip of pointer (C) against division lines on the
disk of hand wheel (B).

Fig. 6

www.garudan.cz

8

anita-b



GP-514-446(7)

7 Adjusting Differential Feed Ratio

(only for machines with driven presser foot)

To ensure sewing of fabric layers without their displacement in the course of feeding it is
possible to adjust different lengths of feeding driven by press-wheel and feeding by rotary feed
dog. To adjust shorter lengths of feeding driven by press wheel move collar (A) on lever (B)
towards feeding shaft (D). To increase the length of press-wheel feeding move collar (A) from
the axis of shaft (D).

Fig. 7
An appropriate adjustment of the ratio of the lengths of feeding driven by rotary feed dog and
press-wheel makes it possible to achieve not only the same feeding of fabric layers but, if
necessary, to gather or stretch one of the fabrics.

8 Safety Clutch

Fig. 8

www.garudan.cz

9

anita-b



GP-514-446(7)

The sewing machines are equipped with a safety clutch on the lower shaft (A) fig. 8 that allows
the operator to turn the driving part of lower shaft (A) when the loopers or feed dogs are locked.
The clutch consists of segment (B) engaging with.groove (C) in the disk on lower shaft by the
pressure of two springs. The spring pressure can be regulated with hexagon screws (D). If the
clutch is skipping over find out the cause and remove the fault. Only a specia!ist is al!owed to
adjust the clutch force. The clutch must not slip in the course of normal sewing! If it is the case
call a specialist to examine and adjust the machine.

9 Maintenance

Caution!

Switch off the main switch and remove your feet from the pedals on the machine support before
cleaning and oiling of the machine so that the machine may not be started by unintended
treading on the pedal.

Cleaning:

Keep the machines clean and at least once a day (depending on the fabrics used) remove dirt
and waste from the looper and feed dog area. If the machine is equipped with a thread trimmer
clean the trimming area, as well. Do not use volatile liquids for cleaning they would cause
damages to the machine and to your health. A dry cloth will do. Check if the filter screen on
electric motor is not clogged with dust.

Oiling:

The machine should be oiled with an oil normally used for sewing machines. Every day, before
you start sewing drop one drop of oil into oiling holes marked with red colour on the machine.
Switching-on and switching-of the main switch.

www.garudan.cz

10

anita-b



GP-514-446(7)

10 Switching Off and Switching On of the Main Switch

The Main Switch are marked 0 and I or they have grey/green and red buttons. Pushing position
of the button marked "0" (red) means: off, pushing position of the button marked "I"
(grey/green) means on.

Caution!

Before you start the machine make sure that it is ready for sewing and there is no hard object
placed under the needle.

11 Function of Pedals and Knee Lever

- On machines equipped with one (wide) pedal the pedal regulates sewing speed. When treading
the pedal the sewing speed increases up to maximum speed. If the pedal is in neutral position
the machine stops. If the pedal is treaded backwards (with the heel) the machine will ­depending on its make and the abilities of the stop-motor - tack, cut the thread and lift the
pressing element (press wheel, presser foot). See the Instructions for use of stop-motor for
detailed description of the functions.

- On machines equipped with a mechanically operated clutch the pedal regulates sewing speed
and stops the machine. Presser foot is lifted with the knee lever.

Note: On machines with stop-motor there may be push buttons (one or more) installed on the
machine head. Their function depends on the type of the stop-motor used and their connection is
described in the Instruction for use of stop-motor.

www.garudan.cz

11

anita-b



GP-514-446(7)

12 Bobbin Winder – Standart Built in

Fig. 9

The thread passes from the bobbin stand through thread guide on the winder bracket (1) and
between tension disks (2) and then following the direction of arrow (S) to the empty bobbin.
Install the empty bobbin on the bobbin winder shaft (3). Wrap the bobbin threat around the
empty bobbin in a clockwise direction and push in.
The bobbin winder will stop automatically when the bobbin is full.
Take off full bobbin. Lock the thread under the clip and knife (4). Thread will be cut and kept
the bobbin thread from interfering with the needle thread.

www.garudan.cz

12

anita-b



GP-514-446(7)

Instructions for adjustment threat trimmer mechanism

13 Basic condition

a) Clearance between the throat plate and the bobbin case stopper.

Fig.10

Condition :
Clearance between the top end of the bobbin case resting groove on the throat plate and the top
face of the bobbin case stopper of the hook : 1,4 mm –(for left and right side)

b) To adjust the needle height and the hook course. (Fig. 11)

The hook must be so interrelated with the needle that at the moment when the hook point begins
to take up the upper thread loop, the upper edge of the needle eye comes aproximately 1 ÷ 1,2
mm under the hook point.
Rotate the hand wheel towards you until the needle reaches its bottom position and reacends by
3 mm. In this position, the hook point must lie in the needle axis.

Fig. 11

www.garudan.cz

13

anita-b



GP-514-446(7)

c) The range of technological use – double needle machine

Needle: 134 LR size 75 – 120. According to the chosen material, threads and
needle gauge it is necessary to choose throat plate insert and also throat plate (table I2- Parts
Book) .

Large hooks. Sewing speed max.-1600(spm). Stitch length max.-5mm.

14 To adjust the moving knife (Fig. 12) (table J,I1,I2-Parts Book)

a) Height of the moving knife
Loosen the screw ( J/27, I2/43) in the arm of lever (J/11, I2/42) and the two screws (I1/
25,I2/39) in the axial ring (I1/23,I2/40), and move by knife shaft (I1/21,I2/37) in the direction of
the
arrow 1.

Condition:
Clearance between the top face of the moving knife (I1/20,I2/36) and throat plate: 0,7 mm

Fig.12

b)The moving knife (I1/20) moves freely on the hole of the stroke from the initial position
(warning - clearance between throat plate and also between the bobbin case stopper).
Loosing the screw (I1/26) of the moving knife (I1/20) and move it in the direction of the arrow
2 in the groove of the moving knife shaft.

15 To adjust the holder of counter knife and clamp spring. (Fig. 13)(table I1,I2 –Parts Book)

Loosen two screws (I1/27) in the holder (I1/3). Adjust the vertical position of the clamp spring
by moving the counter knife holder up and down.
Clearance between the moving knife (I1/20) and the clamp spring (I1/8) : 0,1 - 0,2 mm
After the adjustment, tighten two screws (I1/27).

Fig. 13

www.garudan.cz

14

anita-b



GP-514-446(7)

16 To adjust the counter knife (Fig. 14)(table I1,I2,J-Parts Book)

Counter knife (I1/7) is located on the holder (I1/3).
After releasing the screw (I1/19), mildly push the counter knife (I1/7) on the moving knife
(I1/20) by the means of the excentric pin (I1/9) which means in the following position : counter
knife blade must come into the contact approx.5 mm distance from the front of the moving
knife (I1/20). In this position the pressure is secured by the screw (I1/19). For ensuring the
reliability and long service life of thread trimmer mechanism´s parts it is important to secure
the thread cutting with minimal pressure strength of counter knife (I1/7) on the moving knife
(I1/20).

With each adjustment of the pressure check out by manual cutting of two threads inserted into
the gap of the moving knife and by the movement against the counter knife check up their
corect cut out.
By this adjustment the screw (J/27,I2/43) on the bracket (J/11,I2/42) is released.

Fig. 14

17 To adjust the clamp spring (table I1,I2 – Parts Book)

Position of the clamp spring (I1/8) adjust using the screw (I1/28) in the holder (I1/3).
Move the clamp spring so that it is slightly in contact with the moving knife (in direction of the
arrow – Fig. 13 )

Manually actuate thread trimming to check that the bobbin thread is clamped.

RESULTS OF IMPROPER ADJUSTMENT
If the pressure of clamp spring is to big :

- Length of thread remaining on the material after thread trimming will be lengthened,
the sewing start is wrongly attached.

- The moving knife may be locked.
If the clearance between the moving knife and the clamp spring is larger than the specified value

:

- Clamping failure or stitch skipping at the sewing start may result.

www.garudan.cz

15

anita-b



GP-514-446(7)

18 To adjust the thread trimming cam (Fig.15)(table J,I1,I2 – Parts Book)

Axial position of the trimming c am(J/1) is in contact with the axial ring (J/8).
a)Adjust the thread take up lever to top dead point.
In this position, adjust the actuating cam using two screws (J/30) so as the revolving pin (J/5,6)
is insert into cam closely behind point of finish thread trimming.
The more is the cam turned in the sense of rotation of the lower shaft, the sooner begins the
motion of the moving knife (I1/20,I2/36), and inversely.

Fig.15

b) Position of the stoppers (table J,I2- Parts Book)
The revolving pin (J/5,6) is a part of the driving arm (J/4) with a round end. This end touches
two stoppers (J/9,10). Loosen two screws (J/26) and press the first stopper (J/9) comes in
contact with the round end of driving arm (the revolving pin (J/5,6) is inserted into cam). Now
press the second stoopper (J/10) until the stopper comes closely to round end of driving arm.
After the adjustment, tignhten the screws (J/27,I2/43).
If the adjustment is right the revolving pin and the round end of driving arm (J/4) must be easily
inserted.

19 To adjust length of rod (table J – Parts Book)

Lenght of rod (J/12) with joint bearings (J/28) is adjusted so that the driving arm (J/11) could
not come into the contact with the bed plate or with hook shaft. The move of arm should be
symetric on both sides.
After then fix lenght of rod by two nuts (J/25).

www.garudan.cz

16

anita-b



GP-514-446(7)

20 To adjust the initial position of the moving knife (Fig.16)

Adjust the moving knife (I1/20,I2/36) into the initial position. A clearance of approx. 1 mm must
be provided between the top end of the moving knife and of the counter knife.

After then tighten the screw (J/27,I2/43) in arm (J/11,I2/42) (the revolving pin (J/5) is inserted
into cam (J/1)).

Fig.16

21 To adjust the tension thread controller (table A2 – Parts Book)

The tension controller consisting of parts (A2/6,31,7,8,9) influences the lenghts of trimmed ends
in the material and also the lenght of the top thread in the needle after the trimming in
dependence on the used threads and material. It must be adjusted in the way so that the thread
lever could tighten the upper thread to the moving knife, also at the state of detached main
tension controller and also with the fastened lower thread.

22 Conclusion:

When all the trimmer functions have been adjusted as described above, check them as follows:
Insert a bit of material under the top roller, sew a few stitches by hand and check whether the
treads pass through their ducts unobstructed. Then tilt the machine, insert the revolving pin into
the cam controlling the trimmer device drive, rotate the hand wheel and observe the trimmer
device function. When adjusted correctly, the trimmer device cuts the two threads, and the
lower thread end is clamped between the clamping spring and the moving knife. Then check up
the machine in the process and observe esp. tension thread controller etc.

Note: The moving knife must always fasten the lower thread end to the back groove when
moving forward, and the upper thread end to the front groove ( at the trimming hole) when
moving backward.

www.garudan.cz

17

anita-b



TABLE OF CONTENTS

GP-514-446(7)

Spare Parts Lists

A1 Frame and Cover Parts……………………………………………..18,19
A2 Thread Tension Mechanism………………………………………..20,21

B Upper Shaft Mechanism………………………….………………..22,23

C1 Lower Shaft and Clutch Mechanism………………………………..24,25
C2 Timing Belt DrivingMechanism……………………………………26,27

D3 Feed Shaft Mechanism……………………………………………...28,29
D4 Stitch Adjuster Mechanism……………………….………………...30,31

E Needle Bar and Presser Foot Mechanism…………………………...32,33

F Thread Take-Up Lever Mechanism…………………………………34,35

G1 Roller Presser Foot Mechanism……………………………………..36,37
G2 Presser Foot Bar Mechanism……………………….……………….38,39

H1 Right Side Hook Mechanism……………………….……………….40,41
H2 Left Side Hook Mechanism…………………………………………42,43

I1 Right Side Hook Post Mechanism………………………………….44,45
I2 Left and Middle Side Post Mechanism…………….……………….46,47

J Knife Actuating Mechanism………………………………………...48,49

K Backtacking Mechanism

K1 Needle Feed and Driven Roller Mechanism………………………...50,51
K2 Left Side Post and Backtacking Feed Mechanism….……………….52,53
K3 Upper Driven Roller Backtacking Feed Mechanism..………………54,55
K4 Telescopic Shaft Driven Roller Mechanism………………………...56,57
K5 Upper Shaft Driven Roller Mechanism……………………………..58,59
K6 Rods Lower Backtacking Mechanism………………………………60,61
K8 Electric Accessory…………………………………………………...62,63

L Auto Presser Lifting Solenoid Mechanism………….………………….64

N1 Bobbin Winder………………………………………………………….65
N2 Accesories…………………………………………………………...66,67

www.garudan.cz

18

anita-b



Frame and Cover Parts

A1

GP-514-446(7)

www.garudan.cz

19

anita-b



Frame and Cover Parts

A1

GP-514-446(7)

Ref.No.

Part No.

Name of Part Q´ty

A1-1 GP/

1-5

Face Plate 1

A1-2 GP/

108246

Screw (M5x0,8x25) 1

A1-3 GP/

108234

Screw (M5x0,8x35) 1

A1-4 GP/

168061

Thread Take-up Cover 1

A1-5 GP/

210210

Screw (M5x0,8x8) 1

A1-6 GP/

119027

4 Hole Thread Retainer 1

A1-7 GP/

314946

Screw (M4x0,7x4) 1

A1-8 GP/

SM1-6

Arm Side Cover 1

A1-9 GP/

700335

Screw (M5x08x7) 5

A1-10 GP/

118430

Thread Guide Wire 1

A1-11 GP/

700336

Screw 1

A1-12 GP/

SM5-41.25

Arm Side Cover 1

A1-13 GP/

119686-1

Thread Guide Wire 1

A1-14 GP/

119686

Thread Guide Wire 1

A1-16 GP/

119092

Bracket 1

A1-17 GP/

M6x16

Screw (M6x16 DIN 912) 2

A1-18 GP/

119091

Bottom Cover 1

A1-19 GP/

108225

Screw (M5x0,8x10) 5

www.garudan.cz

20

anita-b



Thread Tension Mechanism

A2

GP-514-446(7)

www.garudan.cz

21

anita-b



Thread Tension Mechanism

A2

GP-514-446(7)

Ref.No.

Part No.

Name of Part Q´ty

A2-1 GP/

119766-2

Thread Tension Regulator Assy/deska nap.úpl. 0

A2-2 GP/

119171-25

Thread Tension Regulator Assy/deska nap.úpl. 1

A2-3 GP/

EGS3221

Solenoid/magnet EGS 3221 1

A2-4 GP/

SM4-6

Base Plate/deska napína 1

A2-5 GP/

SM2-2.6

Bracket/rameno 1

A2-6 GP/

SM3-11-1

Screw/šroub pomoc.napínae,úpr. Z 3-0155 1

A2-7 GS/

3-0156

Brake Plate/misky pomocného napínae 4

A2-8 GP/

SM4-22

Conus Spring/pružina pomocného napínae 2

A2-9 GS/

3-0158

Nut/matice pomocného napínae 2

A2-10 GP/

SM2-2.8

Pin/kolík 1

A2-11 GP/

SM3-32

Pin/kolík 1

A2-12 GP/

119171-16

Thread Tension Stud/šroub napínae 1

A2-13 GP/

SM3-10

Thread tension stud/šroub napínae 1

A2-14 GP/

DIN934-M2,5

Nut/matice M2,5 DIN 934 2

A2-15 GP/

JV2,0x13,8

Pin/kolík-jehla JV2,0x13,8 2

A2-16 GP/

119171-12

Screw/šroub 2

A2-17 GP/

119171-13

Tension Release Spring/pružina napínae 1

A2-18 GP/

JV2,5x13,8

Pin/kolík-jehla JV2,5x13,8 2

A2-19 GP/

119171-5

Tension Disc/misky napínae 4

A2-20 GP/

119171-22

Tension Disc Washer/podložka napínae 2

A2-21 GP/

119171-3

Tension Spring/pružina napínae 2

A2-22 GP/

119171-1

Nut/matice napínae 3

A2-23 GP/

119171-23

Screw/šroub (M2,5x8 DIN 84A) 0

A2-24 GP/

119171-24

Screw/šroub (M2,5x12 DIN 84A) 1

A2-25 GP/

119171-2

Spring Guide Assy/miska upravovací pružiny 2

A2-26 GP/

119766-1

Thread Take-up Spring/upravovací pružina 0

A2-27 GP/

119171-4

Thread Take-up Spring/upravovací pružina 1

A2-28 GP/

119171-6

Thread Tension Stud/šroub 1

A2-29 GP/

119171-7

Screw/šroub 1

A2-30 GP/

119171-8

Thread Tension Regulator Bushing/pouzdro 1

A2-31 GP/

SM3-11-2

Screw/šroub pomoc.napínae,úpr. z 3-0155 1

A2-32 GP/

JV2,5x21,8

Pin/kolík-jehla JV2,5x21,8 1

A2-33 GP/

118553

Tension Releasing Pin/kol.vypínání napínae 1

A2-34 GP/

175096-1

Screw/šroub 1

A2-35 GP/

700412

Screw/šroub 1

A2-36 GP/

700412-1

Bushing/distanní kroužek 1

www.garudan.cz

22

anita-b



Upper Shaft Mechanism

B

GP-514-446(7)

www.garudan.cz

23

anita-b



Upper Shaft Mechanism

B

GP-514-446(7)

Ref.No.

Part No.

Name of Part Q´ty

B-1 GP/

119702-2

Crank Cam 1

B-2 GP/

130224

Screw (M5x0,8x12) 2

B-3 GP/

119702-3

Screw (M7x1,0x22) 1

B-4 GP/

119702-4

Screw (M7x1,0x16,5) 1

B-5 GP/

700510

Screw (M6x0,75x8) 3

B-6 GP/

119702-5

Bushing 1

B-7 GP/

119702-1

Upper Shaft 1

B-8 GP/

200-002

Upper Shaft Gear Winder 1
B-9 GP/018643 Ball Bearing 2
B-10 GP/069160 Timming Belt 220XL 1

B-11 GP/

119707

Timming Belt Wheel 2
B-12 GP/

335902

Screw (M6x0,75x10) 2
B-13 GP/

335902-1

Screw (M6x0,75x8) 6
B-14 GP/

016153

Ball Bearing 2
B-15 GP/

119705

Upper Shaft Bushing 2
B-16 GP/

069746

Bushing 1
B-17 GP/

168480

Washer 2
B-18 GP/

210265

Screw (M6x1,0x16) 1
B-19 GP/

175048

Feed Regulator Scale 1
B-20 GP/

170913

Pulley Balance Wheel 1
B-21 GP/

341902

Screw (M6x1,0x16) 2
B-22 GP/

210287

Screw (M6x1,0x35) 1

www.garudan.cz

24

anita-b



Lower Shaft and Clutch Mechanism

C1

GP-514-446(7)

www.garudan.cz

25

anita-b



Lower Shaft and Clutch Mechanism

C1

GP-514-446(7)

Ref.No.

Part No.

Name of Part Q´ty

C1-1 GP/

175025

Shaft 1

C1-2 GP/

518250

Retaining Ring 1

C1-3 GP/

119711

Shaft 1

C1-4 GP/

175019

Coupler 1

C1-5 GP/

341901

Screw (M6x0,75x6) 4

C1-6 GP/

133109

Coupler 1

C1-7 GP/

119081A

Connecting Plate 1

C1-7- 1 GP/

700510

Screw (M6x0,75x7) 2

C1-7- 2 GP/

173263

Safety Clutch Seat 1

C1-7- 3 GP/

013153

Spring 2

C1-7- 4 GP/

173261

Latch 1

C1-7- 5 GP/

009408

Hinge Stud 1

C1-7- 6 GP/

173264

Coupler (right) 1

C1-7- 7 GP/

065052

Pin 4

C1-7- 8 GP/

640150

E - Ring 1

C1-7- 9 GP/

175023

Stud 2

C1-7-10 GP/

640130

E - Ring 1

C1-7-11 GP/

013076

Drop - In Pin 1

C1-7-12 GP/

069037

Washer 1

C1-7-13 GP/

009343

Spring 1

C1-7-14 GP/

175126

Screw 1

C1-7-15 GP/

M5X5

Screw M5X5 DIN 916 2

www.garudan.cz

26

anita-b



Timing Belt Driving Mechanism

C2

GP-514-446(7)

www.garudan.cz

27

anita-b



C2

GP-514-446(7)

Ref.No.

Part No.

Name of Part Q´ty

C2-1 GP/

119097

Plug 2

C2-2 GP/

610300

Retaining Ring 1

C2-3 GP/

018624

Ball Bearing 2

C2-4 GP/

119707

Timming Belt Wheel 1

C2-5 GP/

335902-1

Screw (M6x0,75x8) 2

C2-6 GP/

335902

Screw (M6x0,75x10) 2

C2-7 GP/

119121

Collar (Left) 1

C2-8 GP/

700689

Screw (M6x0,75x4,5) 4

C2-9 GP/

018613

Ball Bearing 1

C2-10 GP/

119708

Timming Belt Wheel 1

C2-11 GP/

069161

Timming Belt 210XL 1

C2-12 GP/

119706

Shaft 1

C2-13 GP/

118722

Collar (Right) 1

www.garudan.cz

28

anita-b



Feed Shaft Mechanism

D3

GP-514-446(7)

www.garudan.cz

29

anita-b



Feed Shaft Mechanism

D3

GP-514-446(7)

Ref.No.

Part No.

Name of Part Q´ty

D3-1 GP/

610280

Retaining Ring 1

D3-2 GP/

119085

Washer 1

D3-3 GP/

133283

Washer 6

D3-4 GP/

215124

Needle Bearing 3

D3-5 GP/

118600

Bushing 1

D3-10 GP/

119084

Shaft 1

D3-11 GP/

118601

Bushing 1

D3-12 GP/

119521

Crank 1

D3-13 GP/

130224

Screw (M5x0,8x12) 4

D3-14 GP/

335902-1

Screw (M6x0,75x8) 2

D3-15 GP/

119521-1

Crank 1

D3-16 GP/

700689

Screw (M6x0,75x4,5) 3

D3-17 GP/

118603

Bushing 1

D3-18 GP/

118893

Collar 1

www.garudan.cz

30

anita-b



Stitch Adjuster Mechanism

D4

GP-514-446(7)

www.garudan.cz

31

anita-b



Stitch Adjuster Mechanism

D4

GP-514-446(7)

Ref.No.

Part No.

Name of Part Q´ty

D4-1 GP/

175038

Connecting Rod 1

D4-2 GP/

069060

Ball Bearing 1

D4-3 GP/

175038A

Crank Rod Set 1

D4-4 GP/

215028

Needle Bearing 1

D4-5 GP/

118612

Bearing Stud 1

D4-6 GP/

165356

Feeding Adjusting Plate 1

D4-7 GP/

165356-1

Screw (M5x0,8X20) 1

D4-8 GP/

165356-8

Nut (M5x0,8x4) 1

D4-9 GP/

165356-5

Spring 1

D4-10 GP/

165356-7

E-Ring 1

D4-11 GP/

165356-6

Spring 1

D4-12 GP/

165356-2

Pin 1

D4-13 GP/

165356-3

Screw (M6x1,0) 1

D4-14 GP/

175029

Cam Assy 1

D4-14-1 GP/

175029-1

Stitch Regulating Seat 1

D4-14-2 GP/

175029-2

Stitch Regulating Fix Seat 1

D4-14-3 GP/

175029-3

Feed Adjusting Screw 1

D4-14-4 GP/

175029-4

Screw M3.5X8 2

D4-14-6 GP/

175029-6

Friction Plate 1

D4-14-7 GP/

175029-7

Screw (M6x0,75x10) 2

D4-14-9 GP/

175029-9

Screw (11/64x40x2,5) 2

D4-14-10 GP/

175029-10

Eccentric Wheel 1

D4-14-11 GP/

175029-11

Spring 1

D4-14-12 GP/

175029-12

Collar 1

D4-14-13 GP/

175029-13

Screw (M4X8) DIN 912 2

D4-14-15 GP/

169137

Washer 4x14x0.5 DIN 988 1

www.garudan.cz

32

anita-b



Needle Bar Feed and Presser Foot Mechanism

E

GP-514-446(7)

www.garudan.cz

33

anita-b



Needle Bar Feed and Presser Foot Mechanism

E

GP-514-446(7)

Ref.No.

Part No.

Name of Part Q´ty

E-1 GP/

118197

Needle Bar 1
E-2 GP/

118196

Ring Clamp 1
E-3 GP/

108174-1

Screw (M4x0,7x8) 1
E-4 GP/

700868

Screw (1/8x44x3,5) 1
E-5 GP/

700868-1

Screw (M3x0,5x4) 1
E-6 GP/

118195

Needle Holder (2,8) 1
E-6 GP/

118195-1

Neelde Holder (2,4) 1
E-6 GP/

118195-2

Needle Holder (3,2) 1
E-10 GP/

175150

Pin 1
E-11 GP/

215028

Needle Bearing 2
E-12 GP/

169137

Washer (14x8x0.5mm) 2
E-13 GP/

305305

Screw (M6x1,0x25) 2
E-14 GP/

024191

Nut (M6x1,0x4,8) 2
E-15 GP/

118612

Pin 1
E-16 GP/

119718

Shaft 1
E-16.I GP/

118545

Ewasher 1
E-17 GP/

030310

Pin 1
E-18 GP/

119046

Connecting Rod 1
E-19 GP/

119525-2

Washer 1
E-20 GP/

119718-2

Retaining Ring (12mm) 1
E-21 GP/

118858

Spring Plate 1
E-22 GP/

108285

Screw (M6x1,0x8) 1
E-23 GP/

118857

Spring 1
E-24 GP/

118543

Crank 1
E-25 GP/

118544

Pin 1
E-26 GP/

118543A

Crank Shaft 1
E-27 GP/

640150

E-Ring 1
E-28 GP/

020490

Spring Plate 2
E-29 GP/

130224

Screw (M5x0,8x16) 1
E-30 GP/

118600

Bushing 2
E-31 GP/

215124

Needle Bearing 0
E-32 GP/

133283

Washer 0
E-33 GP/

118610

Crank 0
E-34 GP/

108285-1

Screw (M6x1,0x1,4) 0
E-35 GP/

130224

Screw (M5x0,8x12) 0
E-37 GP/

118594

Needle Bar Connecting Link Guide 1
E-38 GP/

100355

Screw (M4x0,7x6) 2
E-39 GP/

119014

Oil Felt 1
E-40 GP/

119015

Holder 3
E-41 GP/

706169

Screw (M4x0,7x4,5) 2
E-42 GP/

119940

Needle Bar Holder 1
E-43 GP/

119940-5

Needle Bar Bushing 1
E-44 GP/

119940-4

Needle Bar Bushing 1
E-45 GP/

118504

Collar 1
E-46 GP/

700689

Screw M6x0.75x4.5 1

www.garudan.cz

34

anita-b



Thread Take-Up Lever Mechanism

F

GP-514-446(7)

www.garudan.cz

35

anita-b



Thread Take-Up Lever Mechanism

F

GP-514-446(7)

Ref.No.

Part No.

Name of Part Q´ty

F-1 GP/

118084

Thread Take-up Assy 1
F-2 GP/

119009

Take-up Lever Support Stud 1
F-3 GP/

168039

Washer 2
F-4 GP/

215022

Needle Bearing 2
F-5 GP/

119008

Take-up Frame 1
F-6 GP/

119762

Take-up Crank Pin 1
F-7 GP/

119049

Bushing 1
F-8 GP/

119007

Take-up Lever 1
F-9 GP/

167569

Ball Bearing 1
F-10 GP/

167570

Ball Bearing 2
F-11 GP/

119006

Take-up Lever 1
F-13 GP/

168047

Screw (M4x0,7x13,5) 1
F-14 GP/

610210

Retaining Ring 2
F-15 GP/

039177

Screw (M4x0,7x12,5) 1
F-16 GP/

119013

Needle Bar Connecting Stud 1
F-17 GP/

119765

Needle Bar Connecting Crank Rod 1
F-18 GP/

119763

Washer 1
F-19 GP/

218080

Needle Bearing 1
F-20 GP/

118518

Needle Bar Guide Slide Block 1
F-21 GP/

168041

Bushing 1
F-22 GP/

314220

Screw (M5x0,8x8) 3

www.garudan.cz

36

anita-b



Roller Presser Foot Mechanism

G1

GP-514-446(7)

www.garudan.cz

37

anita-b



Roller Presser Foot Mechanism

G1

GP-514-446(7)

Ref.No.

Part No.

Name of Part Q´ty

G1-1 GP/

119803

Roller Preser Assy (Large) 1

G1-2 GP/

119803-1

Roller Preser Assy (Middle) 1

G1-3 GP/

119802

Roller Preser Assy (Small) 2

G1-4 GP/

119469

Spring Washer 2

G1-5 GP/

033145

Pin 1

G1-6 GP/

175109

Gear 1

G1-6-1 GP/

175109-1

Gear Presser Shaft 1

G1-6-2 GP/

175109-2

Gear 1

G1-6-3 GP/

175109-3

Roller Bracket 1

G1-6-4 GP/

175109-4

Roller Bracket 1

G1-6-5 GP/

175109-5

Ball d.2mm 20

G1-6-6 GP/

175109-6

Screw 3

G1-6-7 GP/

175109-7

Screw 3

G1-7 GP/

175107

Gear 1

G1-7-1 GP/

175107-1

Gear Presser Shaft 2

G1-7-2 GP/

175107-2

Gear 1

G1-8 GP/

175108

Gear 1

G1-8-1 GP/

175108-1

Gear Presser Shaft 1

G1-8-2 GP/

175108-2

Gear 2

G1-9 GP/

664290

Retaining Ring 1

G1-10 GP/

133116

Ball Bearing 2

G1-10-1 GP/

133116-1

Washer 1

G1-11 GP/

518210

Retaining Ring 1

G1-12 GP/

119953

Roller Presser Bracket 1

G1-13 GP/

119943

Roller Presser Bracket 1

G1-14 GP/

119956

Roller Presser Bracket 1

G1-15 GP/

210043

Screw (M2,5x0,45x6) 1

G1-16 GP/

119491

Washer 1

G1-17 GP/

119807

Guide Seat 1

G1-18 GP/

119955

Guide Seat 1

G1-19 GP/

119954

Guide Seat 1

G1-20 GP/

173174

Screw (M4x0,7x8) 1

www.garudan.cz

38

anita-b



Presser Foot Bar Mechanism

G2

GP-514-446(7)

www.garudan.cz

39

anita-b



Presser Foot Bar Mechanism

G2

GP-514-446(7)

Ref.No.

Part No.

Name of Part Q´ty

G2-1 GP/

119019

Presser Bar Bushing (Upper) 1

G2-2 GP/

700785

Screw (M5x0,8x6) 1

G2-3 GP/

119018

Presser Bar Bushing (Upper) 1

G2-4 GP/

118530

Presser Bar Holder 1

G2-5 GP/

700510

Screw (M6x0,75x8) 2

G2-6 GP/

119019-1

Presser Bar Bushing (Lower) 1

G2-7 GP/

700510-1

Screw (M6x1,0x8) 1

G2-8 GP/

119165-1

Roller Presser Holder 1

G2-9 GP/

119165

Roller Presser Holder 1

G2-10 GP/

173174

Screw (M4x0,7x8) 1

G2-11 GP/

025874

Spring 1

G2-12 GP/

054876

Angle 1

G2-13 GP/

130173

Screw (M4x0,7x9) 1

G2-14 GP/

175135N

Cover 1

G2-15 GP/

700335

Screw (M5x0,8x7) 2

G2-16 GP/

069079

Presser Foot Lifter 1

G2-17 GP/

317950

Screw (M5x0,8x6) 1

G2-18 GP/

119004

Bushing 1

G2-19 GP/

118577

Cam Shaft 1

G2-20 GP/

100331

Screw (M8x0,75) 1

G2-21 GP/

118535

Presser Plate Spring 1

G2-22 GP/

343901

Screw (M6x1,0) 1

G2-23 GP/

118105

Stud 1

G2-24 GP/

314286

Screw (M6x1,0x8) 1

G2-25 GP/

700017

Screw (M6x1,0) 1

G2-26 GP/

119016

Spring 1

G2-27 GP/

49657

Gauge/vodi (2,4mm-3/32") *1

G2-27-1 GP/

049657-1

Gauge/vodi (1,6mm-1/16") *1

G2-28 GP/

108171

Screw (M4x0,7x6) 1

G2-29 GP/

118542

Knee Lifter Connecting Lever 1

G2-30 GP/

118536

Spring Plate 1

G2-31 GP/

118536-1

Pin 1

G2-32 GP/

118539

Bushing 1

G2-33 GP/

640150

E-Ring 1

G2-34 GP/

118536A

Lifting Lever Assy 1

G2-36 GP/

400-MG

Support/opra 1

www.garudan.cz

40

anita-b



Right Side Hook Mechanism

H1

GP-514-446(7)

www.garudan.cz

41

anita-b



Right Side Hook Mechanism

H1

GP-514-446(7)

Ref.No.

Part No.

Name of Part Q´ty

H1-1 GP/

G400TL

Hook Complete With Bobbin Case-Large 1

H1-1-1 GP/

G400TL-749

Hook complete without cap 1

H1-1-2 GP/

G400TL-102

Hook without cap holder 1

H1-1-3 GP/

G400T-017

Tension spring fastening screw 1

H1-1-4 GP/

G400TL-104

Gib 1

H1-1-5 GP/

G400T-005

Gib srew 3

H1-1-6 GP/

G400TL-111

Tension spring 1

H1-1-7 GP/

G400T-018

Tension spring adjusting screw 1

H1-1-9 GP/

G400TL-750

Complete cap holder 1

H1-1-12 GP/

G400TL-701

Cap 1

H1-1-33 GP/

G400TL-105

Nedle guard 1

H1-2 DC/

239729S

Bobbin 1

H1-3 GP/

410-444-010

Screw 1

H1-5 GP/

119128

Oil Felt 1

H1-6 GP/

119127

Rotating Hook Opener Bracket 1

H1-7 GP/

410-449-003

Rotating Hook Opener 1

H1-8 GP/

M3x8

Screw (M3x0,5x8) DIN 84A 2

H1-9 GP/

694ZZ

Ball Bearing 1

H1-9-1 GP/

119106-1

Driver 1

H1-10 GP/

119106

Driver 1

H1-11 GP/

108177

Screw (M4x0,7x10) 1

H1-12 GP/

119105

Washer(35.5x26x1mm) 1

H1-13 GP/

410-444-002

Hook Driver 1

H1-14 GP/

410-444-003

Hook Shaft 1

H1-15 GP/

215031

Needle Bearing 1

H1-16 GP/

215028

Needle Bearing 1

H1-17 GP/

119524

Feed Wheel Shaft 1

H1-18 GP/

119979

Bushing 1

H1-19 GP/

664390

Retaining Ring (26mm) 1

H1-20 GP/

175138

Bushing 1

H1-21 GP/

SM2-3.14

Bushing 1

H1-22 GP/

SM2-3.20

Screw 1

H1-23 GP/

341901

Screw (M6x0,75x6) 4

H1-24 GP/

131088

Collar 1

H1-25 GP/

125010

Washer (0,5) 2

H1-25-1 GP/

122718

Washer (0,1) 1

H1-25-2 GP/

125008

Washer (0,15) 1

H1-25-3 GP/

125009

Washer (0,2 1

H1-26 GP/

119133-1

Bevel Gear (Small) 1

H1-27 GP/

119133-2

Bevel Gear (Large) 1

H1-28 GP/

700689

Screw (M6x0,75x4,5) 4

H1-29 GP/

341901-1

Screw (M6x0,75x5) 2

H1-30 GP/

119133

Gear Set 1

H1-31 GP/

123788

Collar 1

H1-32 GP/

119105-2

Washer 1

H1-33 GP/

410-444-006

Pin/unášecí ep výstedníku 1

www.garudan.cz

42

anita-b



Left Side Hook Mechanism

H2

GP-514-446(7)

www.garudan.cz

43

anita-b



Left Side Hook Mechanism

H2

GP-514-446(7)

Ref.No.

Part No.

Name of Part Q´ty

H2-1 GP/

G400TL

Hook Complete With Bobbin Case 1

H2-1-1 GP/

G400TL-749

Hook complete without cap 1

H2-1-2 GP/

G400TL-102

Hook without cap holder 1

H2-1-3 GP/

G400T-017

Tension spring fastening screw 1

H2-1-4 GP/

G400TL-104

Gib 1

H2-1-5 GP/

G400T-005

Gib screw 3

H2-1-6 GP/

G400TL-111

Tension spring 1

H2-1-7 GP/

G400T-018

Tension spring adjusting screw 1

H2-1-9 GP/

G400TL-750

Complete cap holder 1

H2-1-12 GP/

G400TL-701

Cap 1

H2-1-33 GP/

G400TL-105

Needle guard 1

H2-2 DC/

239729S

Bobbin 1

H2-3 GP/

410-444-010

Screw 2

H2-4 GP/

119108

Feed Wheel Shaft 1

H2-5 GP/

119128

Oil Felt 1

H2-6 GP/

119127

Rotating Hook Opener Bracket 1

H2-7 GP/

410-449-003

Rotating Hook Opener 1

H2-8 GP/

108093

Screw (M3x0,5x6) 2

H2-9 GP/

694 ZZ

Ball Bearing 1

H2-9-1 GP/

414-443-006

Driver 1

H2-10 GP/

119106-006

Driver Assy 1

H2-11 GP/

108177

Screw (M4x0,7x10) 1

H2-12 GP/

119105

Washer (35,5x26x1mm) 1

H2-13 GP/

410-444-002

Hook Driver 1

H2-14 GP/

410-444-003

Hook Shaft 1

H2-15 GP/

215031

Needle Bearing 1

H2-16 GP/

215028

Needle Bearing 1

H2-18 GP/

119979

Bushing 1

H2-19 GP/

664390

Retaining Ring (26mm) 1

H2-20 GP/

175138

Bushing 1

H2-21 GP/

SM2-3.14

Bushing 1

H2-22 GP/

SM2-3.20

Screw (M6x1,0x25) 1

H2-24 GP/

119108-1

Washer 2

H2-25-1 GP/

122718

Washer (0,1) 1

H2-25-2 GP/

125008

Washer (0,15) 1

H2-26 GP/

119133-1

Bevel Gear (Small) 1

H2-27 GP/

119133-2

Bevel Gear (Large) 1

H2-28 GP/

700689

Screw (M6x0,75x4,5) 8

H2-29 GP/

341901-1

Screw (M6x0,75x5) 4

H2-30 GP/

119133

Gear Set 1

H2-31 GP/

123788

Collar 1

H2-32 GP/

141710

Needle Bearing 2

H2-33 GP/

119947

Washer 1

H2-34 GP/

414-443-003

Driwing Wheel 1

H2-35 GP/

119109

Bevel Gear Assy 1

H2-36 GP/

119109-2

Bevel Gear (Small) 1

H2-37 GP/

119109-1

Bevel Gear (Large) 1

H2-38 GP/

119104

Pull - Off Shaft 1

H2-39 GP/

125010

Washer 1

H2-40 GP/

119105-2

Washer 1

H2-41 GP/

410-44-006

Pin/ep 1

www.garudan.cz

44

anita-b



Right Side Hook Post Mechanism

I1

GP-514-446(7)

www.garudan.cz

45

anita-b



Right Side Hook Post Mechanism

I1

GP-514-446(7)

Ref.No.

Part No.

Name of Part Q´ty

I1-1 GP/

SM2-3.1M

Hook Post/chapaový sloupek 1

I1-2 GP/

250084

Srew/šroub(M3x0.5x6) 2

I1-3 GP/

410-449-004

Holder/držák pevného nože 1

I1-5 GP/

175318

Stud/excentr 1

I1-6 GP/

330217

Screw/šroub(M5x4.5) 1

I1-7 GP/

410-449-005

Counter Knife/Pevný nž 1

I1-8 GP/

410-449-007

Hold Spring/pidržovací perko 1

I1-9 GP/

SM4-24

Pin/excentrický ep 1

I1-10 GP/

119143

Spring Plate/pružná západka 1

I1-11 GP/

108093

Screw/šroub(M3x0,5x6) 1

I1-12 GP/

135292

Screw/šroub(M6x1x15) 4

I1-13 GP/

305174

Washer/podložka 4

I1-14 GP/

016120

Ball Bearing/kul.ložisko 1

I1-15 GP/

119121

Collar/pouzdro 1

I1-16 GP/

700689

Screw/šroub (M6x0,75x4,5) 2

I1-18 GP/

119499

Cover Plate/kryt 1

I1-19 GP/

SM4-25

Screw/šroub 1

I1-20 GP/

410-449-002

Moving Knife/pohyblivý nž 1

I1-21 GP/

SM2-3.3

Trimming Shaft/odstihová hídel 1

I1-22 GP/

SM2-3.6

Tube/trubka 1

I1-23 GP/

SM2-3.5

Distance Ring/distanní kroužek 1

I1-24 GP/

SM2-3.4

Housing/pouzdro 1

I1-25 GP/

M4x5

Screw/šroub M4x5 DIN 916 4

I1-26 GP/

M4x8

Screw/šroub M4x8 DIN 912 1

I1-27 GP/

M4x8

Screw/šroub M4x8 DIN 84A 2

I1-29 GP/

101076

Post Cap Assy/kryt chapae úplný 1

I1-30 GP/

108093

Screw 2

I1-31 GP/

101076-1

Pin/ ep 1

I1-32 GP/

101076-2

Hinge/závs 1

I1-33 GP/

101076-3

Post Cap/kryt chapae 1

www.garudan.cz

46

anita-b



Left and Middle Side Post Mechanism

I2

GP-514-446(7)

www.garudan.cz

47

anita-b



Left and Middle Side Post Mechanism

I2

GP-514-446(7)

Ref.No.

Part No.

Name of Part Q´ty

I2-1 GP/

SM3-2

Hook Post/levý chapaový sloupek 1

I2-2 GP/

119499

Cover Plate/kryt 1

I2-3 GP/

250084

Screw/šroub (M3x0,5x6) 2

I2-4 GP/

135292

Screw/šroub (M6x1x15) 4

I2-5 GP/

305174

Washer/podložka 4

I2-6 GP/

016120

Ball Bearing/kul.ložisko 1

I2-7 GP/

119121

Collar/pouzdro 1

I2-8 GP/

700689

Screw/šroub (M6x0,75x4,5) 2

I2-9 GP/

175318

Stud/excentr 1

I2-10 GP/

330217

Screw/šroub (M5x4,5) 1

I2-11 GP/

119143

Spring Plate/pružná západka 1

I2-12 GP/

108093

Screw/šroub (M3x0,5x6) 1

I2-13 GP/

119138

Bearing Plate/pítl.deska podávacího koleka 1

I2-14 GP/

SM3-6

Feed Wheel/podávací koleko-úpr. z 119136 1

I2-15 GP/

108174-1

Screw/šroub (M3,5x0,6x10) 2

I2-16 GP/

101076

Post Cap Assy/kryt chapae úplný 1

I2-21 GP/

SM3-24

Screw/šroub M2,5x6-úprava z DIN 963 2

I2-22 GP/

100296

Screw/šroub (M4x0,7x6,5) 2

I2-23 GP/

119296

Support Plate/stední sloupek 1

I2-24 GP/

108174-1

Screw/šroub (M4x0,7x8) 10

I2-25 GP/

414-443-004

Washer/podložka 8

I2-26-1 GP/

414-445-002

Needle Plate/stehová deska (2,4) *1

I2-26-2 GP/

Needle Plate/stehová deska *1

I2-26-3 GP/

Needle Plate/stehová deska *1

I2-26-4 GP/

Needle Plate/stehová deska *1

I2-27-1 GP/

414-445-024

Needle Plate Insert/vložka (2,4)/Hole/otvor 1,8mm

*1

I2-27-2 GP/

414-445-020

Needle Plate Insert/vložka2,0 ()/Hole/otv. 1,6mm

*1

I2-27-3 GP/

Needle Plate Insert/vložka()/Hole/otv

*1

I2-27-4 GP/

Needle Plate Insert/vložka ()/Hole/otv.

*1

I2-27-5 GP/

Needle Plate Insert/vložka ()/Hole/otv.

*1

I2-27-6 GP/

Needle Plate Insert/vložka ()/Hole/otv.

*1

I2-27-7 GP/

Needle Plate Insert/vložka ()/Hole/otv.

*1

I2-28 GP/

410-449-004

Holder/držák pevného nože 1

I2-29 GP/

M4x8

Screw/šroub M4x8 DIN 84A 2

I2-30 GP/

410-449-005

Counter Knife/pevný nž 1

I2-31 GP/

410-449-007

Hold Spring/pidržovací perko 1

I2-33 GP/

SM4-24

Pin/excentr 1

I2-34 GP/

SM4-25

Screw/šroub 1

I2-35 GP/

M4x8

Screw/šroub M4x8 DIN 912 1

I2-36 GP/

410-449-002

Moving knife/pohyblivý nž 1

I2-37 GP/

SM3-3

Trimming Shaft/odstihová hídel 1

I2-38 GP/

SM2-3.6

Tube/trubka 1

I2-39 GP/

M4x5

Screw/šroub M4x5 DIN 916 4

I2-40 GP/

SM2-3.5

Distance ring/distanní kroužek 1

I2-41 GP/

SM2-3.4

Housing/pouzdro 1

I2-42 GP/

SM3-4

Trimming Bracket/odstihová páka 1

I2-43 GP/

M5x12

Screw/šroub M5x12 DIN 912 1

I2-44 GP/

SM3-5

Rod/táhlo 1

I2-45 GP/

SM3-9

Screw/šroub 2

I2-46 GP/

SM3-36

Catch Clamp/tmen 2

www.garudan.cz

48

anita-b



Knife Actuating Mechanism

J

GP-514-446(7)

www.garudan.cz

49

anita-b



Knife Actuating Mechanism

J

GP-514-446(7)

Ref.No.

Part No.

Name of Part Q´ty

J-1 GP/

SM4-20

Cam/vaka 1

J-2 GP/

SM4-21

Holder/držák odstihového magnetu 1

J-3 GP/

SM2-1.3

Lever/páka 1

J-4 GP/

SM2-1.2

Bracket/rameno 1

J-5 GP/

SM2-1.6

Pin/ep 1

J-6 GP/

SM2-1.7

Roller/kladka 1

J-7 GP/

SM2-1.5

Plug/trn 1

J-8 GP/

SM2-1.19

Ring/kroužek 1

J-9 GP/

SM2-1.10

Stopper/doraz 1

J-10 GP/

SM2-1.11

Base/podložka 1

J-11 GP/

SM2-3.2

Trimming bracket/odstih. Rameno 1

J-12 GP/

SM2-1.15

Rod/táhlo 1

J-13 GP/

SM2-1.16

Base/podložka 1

J-14 GP/

SM2-1.13

Screw/šroub 1

J-15 GP/

SM2-1.9

Screw/šroub 1

J-16 GP/

SM2-1.8

Screw/šroub 1

J-17 GP/

SM2-1.14

Spring/pružina 1

J-18 GP/

M4

Nut/matice M4 DIN 934 1

J-19 GP/

EMSA6112-C

Solenoid/magnet EMSA 6112-C 1

J-20 GP/

SM2-1.12

Pin/ep 1

J-21 GP/

2,3

Locking plate for shaft/pojistný kroužek 2,3 DIN6799 2

J-22 GP/

M4x8

Screw/šroub M4x8 DIN 84A 2

J-23 GP/

M6x22

Screw/šroub M6x22 DIN 912 2

J-24 GP/

M6

Nut/matice M6 DIN 934 1

J-25 GP/

M5

Nut/matice M5 DIN 934 3

J-26 GP/

M5x14(20)

Screw/šroub M5x14 DIN 912 3

J-27 GP/

M5x12

Screw/šroub M5x12 DIN 912 0

J-28 GP/

SB PHS 5R

Rod.end.bearing/kloubové ložisko SB PHS 5R 2

J-29 GP/

M5x6

Screw/šroub M5x6 DIN 916 1

J-30 GP/

335902

Screw/šroub M6x0,75x10 2

www.garudan.cz

50

anita-b



Needle Feed and Driven Roller Mechanism

K1

GP-514-446(7)

www.garudan.cz

51

anita-b



Needle Feed and Driven Roller Mechanism

K1

GP-514-446(7)

Ref.No.

Part No.

Name of Part Q´ty

K1-1 GP/

SM5-11.1

Holder/držák 1

K1-2 GP/

M5x12

Screw/šroub M5x12 DIN 912 10

K1-3 GP/

M5x16

Screw/šroub M5x16 DIN 915 1

K1-4 GP/

M5x30

Screw/šroub M5x30 DIN 915 1

K1-5 GP/

SM5-1.10

Shaft/hídel 1

K1-6 GP/

SM5-11.7

Crank/vidlice 1

K1-7 GP/

SM5-1.14

Pin/ep 1

K1-8 GP/

K8x11x10TN

Needle Bearing/jehl.vnec K8x11x10TN 4

K1-9 GP/

SM5-11.4

Connecting Rod/ojnice 30 1

K1-10 GP/

SM5-1.12

Pin/ep 1

K1-11 GP/

BN 1976

Washer/podložka DIN 988 ,8x14x0,5 6

K1-12 GP/

SM5-11.22

Rod/páka 1

K1-13 GP/

M6x16

Screw/šroub M6x16 DIN 912 1

K1-14 GP/

M5

Nut/matice M5 DIN 934 2

K1-15 GP/

SM5-1.13

Pin/ep 1

K1-16 GP/

SM5-1.5

Connecting Rod/ojnice 20 1

K1-17 GP/

SM5-11.13

Pin/ep 1

K1-18 GP/

SM5-11.8

Rod/rameno 1

K1-19 GP/

K8x11x13TN

Needle Bearing/jehl.vnec K8x11x13TN 1

K1-20 GP/

SM5-11.11

Rod/táhlo 1

K1-21 GP/

SM5-11.14

Rod/rameno 1

K1-22 GP/

M5x10

Screw/šroub M5x10 DIN 912 1

K1-23 GP/

M4x4

Screw/šroub M4x4 DIN 916 2

K1-24 GP/

SM5--4.6

Pin/ep 1

K1-25 GP/

SM5-1.17

Shaft/hídel 1

K1-26 GP/

HK0608

Needle Bearing/jehl.ložisko HK 0608 3

K1-27 GP/

4

Locking Plate For Shaft/poj kroužek 4 DIN6799 1

K1-28 GP/

M5x14

Screw/šroub M5x14 DIN 912 2

K1-29 GP/

SM5-1.21

Washer/kroužek 1

www.garudan.cz

52

anita-b



Left Side Post and Lower Backtacking Feed Mechanism

K2

GP-514-446(7)

www.garudan.cz

53

anita-b



Left Side Post and Backtacking Feed Mechanism

K2

GP-514-446(7)

Ref.No.

Part No.

Name of Part Q´ty

K2-1 GP/

SM5-2.11

Rod/Rameno ZB 2

K2-2 GP/

SM5-2.12

Rod/Rameno ZJ 1

K2-3 GP/

SM9-1.6

Rod/rameno 1

K2-5 GP/

M5x12

Screw/šroub M5x12 DIN 912 4

K2-6 GP/

174176

Screw/šroub (M4x10) 8

K2-7 GP/

119087

Oil Felt/plstná podložka 8

K2-8 GP/

SM5-S2.5

Rod/táhlo SB-ZJ 2

K2-9 GP/

SM5-S2.7

Rod/táhlo ZB 1

K2-10 GP/

SM9-1.7

Rod/táhlo 1

K2-11 GP/

SM5-2.13

Bushing/pouzdro B 2

K2-12 GP/

SM5-2.14

Bushing/pouzdro J 2

K2-13 GP/

HF1616

Needle Bearing/volnobžné pouzdro HF 1616 4

K2-15 GP/

SM9-S21

Shaft-Set/Hídel úplná 1

K2-16 GP/

10x22/0,3

Washer/distanní podl. 10x22/0,3 DIN 988 2

K2-17 GP/

6200-2Z

Bearing/ložisko 6200-2Z 2

K2-19 GP/

RB-2,5

Ball/kulika RB - 2,5 6

K2-20 GP/

SM3-2

Support Plate/levý sloupek 1

K2-21 GP/

M6x6

Screw/šroub M6x6 DIN 912 2

K2-22 GP/

SM9-1.13

Cover/kryt 1

K2-23 GP/

30

Retaining Ring/pojistný kroužek 30 DIN 472 4

K2-24 GP/

SM9-11.1

Bracket/tleso 1

K2-25 GP/

SM9-1.5

Ring/distanní kroužek 1

K2-26 GP/

SM9-1.4

Ring/distanní kroužek 1

K2-27 GP/

SM9-1.10

Armrest/podpra 1

K2-28 GP/

M6x25

Screw/šroub M6x25 DIN 912 2

K2-29 GP/

M6x30

Screw/šroub M6x30 DIN 912 1

K2-30 GP/

SM9-1.8

Shaft/hídel 1

K2-31 GP/

5

Retaining Ring/pojistný kroužek 5 DIN 6799 2

K2-32 GP/

627-2Z

Bearing/ložisko 627-2Z 2

K2-33 GP/

664350

Retaining Ring/pojistný kroužek 1

K2-34 GP/

SM9-1.9

Belt/emenice úprava HTD-P20-3M-9 2

K2-35 GP/

080112012

Screw/šroub M5x0,5 080 112.012 4

K2-36 GP/

HTD210-3M-9

Indented Belt/ozub.emen HTD 210-3M-9 1

www.garudan.cz

54

anita-b



Upper Driven Roller Backtacking Feed Mechanism

K3

GP-514-446(7)

www.garudan.cz

55

anita-b



Upper Driven Roller Backtacking Feed Mechanism

K3

GP-514-446(7)

Ref.No.

Part No.

Name of Part Q´ty

K3-1 GP/

SM5-S31N

Shaft-Set/hídel úplná 1

K3-3 GP/

SM5-31.37

Washer/kroužek 1

K4-4 GP/

SM5-31.33

Oil Felt/plstný kroužek 1

K3-5 GP/

130224

Washer/podl.dist. DIN 988,10x16/0,5(+0,3) 1

K3-6 GP/

BR19

Locking Plate/poj.kroužek BR19 4

K3-7 GP/

GE10E

Bearing/kloubové ložisko GE 10 E 2

K3-8 GP/

SM5-31.17

Holder/horní držák 1

K3-9 GP/

3m6x20

Pin/kolík 3m6x20, DIN 6325 1

K3-10 GP/

SM5-31.19

Rod/rameno 1

K3-11 GP/

SM5-31.8

Pin/ep 1

K3-12 GP/

M4

Nut/matice M4, DIN 934 1

K3-13 GP/

2,3

Locking Plate/poj.kroužek 2,3 DIN 6799 1

K3-14 GP/

M5x12

Screw/šroub M5x12 DIN 912 2

K3-15 GP/

SM5-31.20

Washer/kroužek 1

K3-16 GP/

SM3-16

Washer/podložka 3

K3-17 GP/

HF1616

Needle bearing/volnobžné pouzdro HF1616 2

K3-18 GP/

SM5-31.26

Bushing/pouzdro J 1

K3-19 GP/

SM5-31.25

Bushing/pouzdro B 1

K3-20 GP/

16

Locking Plate/poj.kroužek 16 DIN 471 3

K3-21 GP/

51100

Bearing/ložisko axiální 51100 1

K3-22 GP/

SM5-31.28

Washer/kuželová podložka 1

K3-23 GP/

SM5-31.27

Washer/kulová podložka 1

K3-24 GP/

SM5-31.18

Holder/spodní držák 1

K3-25 GP/

M5x16

Screw/šroub M5x16 DIN 912 2

K3-29 GP/

RB-2,5

Ball/kulika RB-2,5 3

www.garudan.cz

56

anita-b



Telescopic Shaft Driven Roller Mechanism

K4

GP-514-446(7)

www.garudan.cz

57

anita-b



Telescopic Shaft Driven Roller Mechanism

K4

GP-514-446(7)

Ref.No.

Part No.

Name of Part Q´ty

K4-1 GP/

SM5-31.29

Shaft/hídel s kulovým kloubem 1

K4-2 GP/

SM5-31.36

Spring/tlaná pružina 1

K4-3 GP/

SM5-31.31

Shaft/hídel 1

K4-4 GP/

2,5m6x12

Pin/kolík 2,5m6x12 DIN6325 1

K4-5 GP/

SM5-31.32

Clutch/kloubová spojka 1

K4-6 GP/

2m6x14

Pin/kolík 2m6x14 DIN 6325 2

K4-7 GP/

M5x30

Screw/šroub M5x30 DIN 427 1

K4-8 GP/

SM5-31.30

Universal Joint 1

K4-9 GP/

M4x4

Screw M4x4 DIN 916 2

K4-10 GP/

SM5-S4

Complete set/kompletní hídel

***Supplied only complete set SM5-S4

www.garudan.cz

58

anita-b



Upper Shaft Driven Roller Mechanism

K5

GP-514-446(7)

www.garudan.cz

59

anita-b



Upper Shaft Driven Roller Mechanism

K5

GP-514-446(7)

Ref.No.

Part No.

Name of Part Q´ty

K5-1 GP/

SM5-31.38

Holder/držák 1

K5-2 GP/

119163

Crank/páka 1

K5-3 GP/

119507

Link/táhlo 2

K5-4 GP/

174176

Screw/šroub(M4x10) 4

K5-5 GP/

119087

Oil Felt/plstný kroužek 4

K5-6 GP/

M5x12

Screw/šroub M5x12 DIN 912 2

K5-7 GP/

2,3

Locking Plate/poj.kroužek 2,3 DIN 6799 1

K5-8 GP/

SM5-41.20

Upper side shaft/hídel 1

K5-9 GP/

118600

Bushing/pouzdro 2

K5-10 GP/

215124

Needle Bearing/jehl.ložisko 2

K5-11 GP/

118504

Collar/kroužek 1

K5-12 GP/

700689

Screw/šroub(M6x4,5) 1

K5-13 GP/

133283

Washer/poj.kroužek 4

K5-14 GP/

SM5-31.10

Nut/matice 2

K5-15 GP/

SM5-31.43

Rod/rameno 1

K5-16 GP/

M4x10

Screw/šroub M4x10 DIN 912 1

K5-17 GP/

SM5-31.7

Pin/spodní ep 1

K5-18 GP/

M4

Nut/matice M4 DIN934 1

K5-19 GP/

SM5-31.42

Rod/táhlo 1

K5-20 GP/

SM5-31.9

Bushing/puzdro 2

K5-21 GP/

M5x14

Screw/šroub M5x14 DIN 912 1

www.garudan.cz

60

anita-b



Rods Lower Backtacking Mechanism

K6

GP-514-446(7)

www.garudan.cz

61

anita-b



Rods Lower Backtacking Mechanism

K6

GP-514-446(7)

Ref.No.

Part No.

Name of Part Q´ty

K6- 1 GP/

SM9-21.6

Holder/držák vahadla B 1

K6- 2 GP/

SM9-21.7

Balance Beam/vahadlo B 1

K6- 3 GP/

SM9-21.5

Bearing Surface/oprka 1

K6- 4 GP/

SM9-2.4

Support/opra 1

K6- 5 GP/

SM9-2.3

Pin/ep 1

K6- 6 GP/

SM5-2.8

Nut/matice 1

K6- 7 GP/

SMS9-2.5

Lever/táhlo úplné 1

K6- 8 GP/

4

Washer/Podložka 4 DIN 9021 4

K6- 9 GP/

SM5-31.36

Spring/pružina 1

K6- 10 GP/

5x20

Washer/Podložka 5x20/1,5 BN 732 1

K6- 11 GP/

M5x12

Screw/šroub M5x12 DIN 912 2

K6- 12 GP/

4

Quicklock/pojistný kr. Quicklock 4 BN 833 3

K6- 13 GP/

SM5-4.10

Rod/rameno 1

K6- 14 GP/

SM5-4.13

Pin/ep 1

K6- 15 GP/

SM5-4.2

Bushing/pouzdro 1

K6- 16 GP/

M4x10

Screw/šroub M4x10 DIN 963A 3

K6- 17 GP/

SM5-41.15

Rod/rameno 1

K6- 18 GP/

SM5-S4.14

Lever/táhlo úplné 1

K6- 19 GP/

SM5-41.14

Rod/rameno 1

K6- 20 GP/

M5x16

Screw/šroub M5x16 DIN 912 1

K6- 22 GP/

HK0608

Needle Bearing/jehl.ložisko HK 0608 2

K6- 23 GP/

5

Locking Plate For Shaft/poj.kr. 5 DIN 6799 2

K6- 24 GP/

M5

Nut/matice M5 DIN 934 1

K6- 25 GP/

M4x4

Srew/šroub M4x4 DIN 916 1

K6- 26 GP/

M6x20

Screw/šroub M6x20 DIN 912 2

K6- 27 GP/

M6x25

Screw/šroub M6x25 DIN 912 2

www.garudan.cz

62

anita-b



Electric Accessory

K8

GP-514-446(7)

www.garudan.cz

63

anita-b



Electric Accessory

K8

GP-514-446(7)

Ref.No.

Part No.

Name of Part Q´ty

K8-1 GP/

2x0,5

Cabel/vodi kruh.prez 2x0,5,l=1,5m 1

K8-2 GP/

2x0,5

Cabel/vodi kruh.prez 2x0,5,l=1m 1

K8-3 GP/

MATE-N-LOK

Connector MATE-N-LOK 1

K8-3-1 GP/

1-480318-0

MATE-N-LOK/kryt dutinek 2P/kab 1

K8-3-2 GP/

1-480319-0

MATE-N-LOK/kryt kolík 2P/kab 1

K8-3-3 GP/

0-163304-2

MATE-N-LOK/dutinka/0,5-1,0 Sn 2

K8-3-4 GP/

0-163305-2

MATE-N-LOK/kolík/0,5-1,0 Sn 2

K8-4 GP/

2x0,35

Cabel/vodi kruh.prez 2x0,35,l=1,25m 1

K8-5 GP/

M4x8

Screw/šroub M4x8 DIN 84A 1

K8-6 GP/

656069

Trough Insert/prchodka F07010SB-16 1

K8-7 GP/

115503

Cable Belt/kabelový pásek 2,5mmx100mm 4

K8-8 GP/

602110

Connector/konektor 2,5 2

K8-9 GP/

121032

Isolator/smršovací isolace 3,2mm,l=30mm 2

K8-11 GP/

4505

Cabel Clamp/kabel.držák CCS 50-S8-C 1

K8-12 GP/

SM5-S41.18

Push Button/tlaítko zpátkování 1

K8-12-1 GP/

SM5-41.19

Prism/upevovací prizma 1

K8-13 GP/

SM5-41.16

Holder/držák 1

K8-14 GP/

M4x6

Screw/šroub M4x6 DIN 84A 2

K8-15 GP/

M3x5

Screw/šroub M3x5 DIN 963A 2

K8-16 GP/

M3

Nut/matice M3 DIN 934 2

K8-17 GP/

EMSA8215-B2

Solenoid/magnet EMSA 8215-B 1

K8-18 GP/

SM5-41.8

Holder/konzola 1

K8-19 GP/

M6x14

Screw/šroub M6x14 DIN 912 3

K8-20 GP/

M4x12

Screw/šroub M4x12 DIN 912 3

K8-24 GP/

SM5-41.22

Bracket/rameno 1

K8-25 GP/

M6x14

Screw/šroub M6x14 DIN 912 1

www.garudan.cz

64

anita-b



Auto Presser Lifting Solenoid Mechanism

L

GP-514-446(7)

Ref. No.

Part No.

Name of Part Q´ty

L- 1 GP/

AEVS072-4

Solenoid/magnet AEVS 072-4 175W 1

L- 2 GP/

SM8-1

Plate/držák 1

L- 3 GP/

SM8-2

Plug/trn 1

L- 4 GP/

M5x10

Screw/šroub M5x10 DIN 963A 3

L- 5 GP/

M5x14

Screw/šroub M5x14 DIN 912 4

L- 6 GP/

M8

Nut/matice M8 DIN 963 1

L- 7 GP/

118543A

Crank Shaft/páka s epem 1

L- 8 GP/

130224

Screw/šroub (M5x12) 2

www.garudan.cz

65

anita-b



Bobbin Winder

N1

GP-514-446(7)

Ref. No.

Part No.

Name of Part Q´ty
500

N1-1 GP/

GU-100T

Bobbin Winder-Built in 1

N1-2 D/

D08082993000

Knife 1

N1-3 D/

D08028312900

Spring 283129 1

N1-4 D/

D08028313000

Spring 283130 1

N1-5 P/

P98002524800

Thread Retainer 1

N1-6 GP/

M3x5

Screw M3x5 DIN 84A 1

N1-7 GP/

941048-1

O Ring 14x6 1

N1-8 GP/

GU-100-024T

Spring 1

N1-9 GP/

GU-100-020T

Pin 1

N1-10 GP/

GU-100-026T

Plug 1

N1-11 GP/

GU-100-025T

Screw 1

N1-12 GP/

GU-100-023T

Spring 1

N1-13 GP/

M4X10

Screw M4x10 DIN 963A 1

N1-14 GP/

GU-100-018T

Spring 1

N1-15 GP/

GU-100-019T

Spring 1

N1-16 GP/

Ball Bearing 2

www.garudan.cz

66

anita-b



Accessories

N2

GP-514-446(7)

www.garudan.cz

67

anita-b



Accessories

N2

GP-514-446(7)

Ref.No.

Part No.

Name of Part Q´ty

N2-1 GP/

123456

Accessory Bag 1

N2-2 GP/

029836

Vinyl Cov

er 1

N2-3 GP/

800110

Spanner 1

N2-4 GP/

129915

Screw Driver (Small) 1

N2-5 GP/

029946

Screw Driver (Middle) 1

N2-6 GP/

029007

Screw Driver (Large) 1

N2-7 GP/

134LR

Needle 10

N2-8 GP/

029394

Oiler 1

N2-9 GP/

119089-1

Stitching Lenght Indicator 1

N2-10 GP/

100355

Screw 1

N2-11 GP/

032808

Head Cushion 2

N2-12 GP/

010079A

Bobbin 4

N2-13 GP/
N2-14 GP/

119026

Spool Pin 1

N2-15 GP/

FPL2

Thread Stand (2-Pole) 0

N2-16 GP/

FPL3

Thread Stand (3-Pole) 1

N2-17 GP/

171543

Spring 1

N2-18 GP/

171542

Knee Lever Coupling 1

N2-19 GP/

171413

Knee Lever Rod 1

N2-20 GP/

171412

Knee Lever Assy 1

N2-21 GP/

171411

Knee Lever Rod Assy 1

N2-22 GP/

029934

Hinge Connection Seat 2

N2-23 GP/

030341

Pin 2

N2-24 GP/

029450

Hinge Pin 2

N2-25 GP/

118636

Oil Pan 1

N2-26 GP/

460157

Screw 6

N2-27 GP/

032717

Head Rest Wood 1

N2-28 GP/

032717-1

Housing Support Stud 1

N2-29 GP/

119078

Belt Cover Set (Large) 1

N2-30 GP/

119088

Belt Cover Set (Small) 1

N2-31 GP/

119999

Wedge 1

N2-32 GP/

119089-2

Screw 2

N2-33 GP/

119078-1

Screw 2

www.garudan.cz

68

www.garudan.cz