GarrettCom PS14P User Manual

Magnum S14 Convenient Switch

&

PS14P Power Source Switch (PoE)

(Members of the Converter Switches family)

Installation and User Guide

www GarrettCom com

..

S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06)

Magnum™ S14 & PS14P (PoE) Convenient Switches

Installation and User Guide

Part #: 84-00100 Rev. B (01/06)

Trademarks
GarrettCom, Magnum, Link-Loss-Learn, S-Ring, Convenient Switch and Converter
Switch are trademarks and Personal Hub is a registered trademark of GarrettCom, Inc.

Ethernet is a trademark of Xerox Corporation
NEBS is a registered trademark of Telcordia Technologies
UL is a registered trademark of Underwriters Laboratories

Copyright © 2005 GarrettCom, Inc. All rights reserved. No part of this publication may
be reproduced without prior written permission from GarrettCom, Inc.
Printed in the United States of America.

www GarrettCom com

Important: The Magnum S14 & PS14P(PoE), 10/100 Mb/s Convenient
Switches contain no user serviceable parts. Attempted service by unauthorized
personnel shall render all warranties null and void. If problems are
experienced with Magnum S14 & PS14P 10/100 Mb/s Convenient Switches,
consult Section 5, Troubleshooting, of this User Guide.

..

i

S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06)

Federal Communications Commission

Radio Frequency Interference Statement

This equipment generates, uses and can radiate frequency energy and if not
installed and used properly, that is in strict accordance with the manufacturer's
instructions, may cause interference to radio communication. It has been tested and
found to comply with the limits for a Class A computing device in accordance with the
specifications in Subpart J of Part 15 of FCC rules, which are designed to provide
reasonable protection against such interference when operated in a commercial
environment. Operation of this equipment in a residential area is likely to cause
interference, in which case the user at his own expense will be required to take whatever
measures may be required to correct the interference.

www GarrettCom com

..

ii

S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06)

Contacting GarrettCom, Inc

Please use the mailing address, phone and fax numbers and email address listed below:

GarrettCom, Inc.

47823 Westinghouse Dr.

Fremont, CA 94539

Phone [phone]

Fax [phone]

Website: http://www.GarrettCom.com

Email: [e-mail]

www GarrettCom com

..

iii

S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06)

TABLE OF CONTENTS Page

1.0 SPECIFICATIONS ............................................................................... 1

1.1 Technical Specifications..................................................................... 1

2.0 INTRODUCTION ............................................................................... 11

2.1 Inspecting the Package and the Product............................................. 12

2.2 Product Description ........................................................................... 13

2.3 Magnum PS14P & S14-Series, with four (RJ-45) Copper ports ......24

2.4 Frame Buffering and Latency............................................................ 25

2.5 Features and Benefits......................................................................... 28

2.6 Applications (S14 Series and PS14P(POE) Switches)

3.0

INSTALLATION............................................................................. 42

Locating the Convenient Switch Unit................................................ 42

3.1

3.2 MC14-TRAY for Rack Mounting of S14-Series & PS14P(POE).... 43

3.3 MC14-TR+PS9 & MC14-TR+PS9X2 for Rack Media Converters.....44

3.4 DIN-Rail mounting option................................................................. 47

3.5 Power Requirements, Power Supply Types for S14-Series Switches48

3.6 Powering the S14H & S14P (DC internal) with power input............... 50

www GarrettCom com

..

iv

S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06)

d

3.7 S14H & S14P, DC-powered, Installation .........................................52

3.7.1 Power Requirement for PS14P(PoE) Power Source Switch.......... 54

3.8 Connecting Twisted Pair (RJ-45 ports).............................................. 55

3.8.1 Connecting Twisted Pair ( Unshielded or Shielded)................. 56

3.8.2 Connections to NICs which support Auto-Neg RJ-45 ports...... 57

4.0 OPERATION.......................................................................................58

4.1 Dual-Speed Functionality, and Switching ......................................... 58

4.2 Auto-cross (MDIX), Auto-negotiation and Speed-sensing................ 60

4.3: Dual LEDs, Front-panel and side-panel (S14-Series & PS14P(PoE))62

5.1 Before Calling for Assistance............................................................ 64

5.2 When Calling for Assistance ............................................................. 65

5.3 Return Material Authorization (RMA) ProcedureError! Bookmark not define

5.4 Shipping and Packaging Information................................................. 67

APPENDIX A: WARRANTY INFORMATION......................................... 69

Revisions
01/06: Updated the PS14P(POE) Power Source Switch
Rev B 05/05: Added

www GarrettCom com

..

Magnum PS14P(POE) Power Source Switch

v

S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06)

10/04: Small edit and updates on power supply option.
09/04: Small edit and updates on UL.

06/04: Small revision of the Agency Approvals
Rev A 03/04: Initial release of this user manual for the S14 Converter Switch

GarrettCom, Inc. reserves the right to change specifications, performance characteristics and/or
model offerings without notice.

www GarrettCom com

..

vi

S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06)

1.0 SPECIFICATIONS

1.1 Technical Specifications

Ports Performance

When a port is operating at 100Mbps:

Data Rate: 100Mbps
When a port is operating at 10 Mbps:
Data Rate: 10 Mbps

Network Standards
100Mb: Ethernet IEEE 802.3u, 100BASE-TX, IEEE 802.1p

10 Mb: Ethernet IEEE 802.3, 10BASE-T
Power Over Ethernet: IEEE 802.3af (PS14P model only)
Auto-sensing for speed: IEEE 802.3u
Data packets that have the 4-bytes tagged VLAN field (802.1q) inserted in

them are received and transmitted unchanged.

www GarrettCom com

..

1

S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06)

Packet-Processing Between Domains

Filter / Forwarding Rate from 100Mbps ports: 148,800 pps max

Filtering and Forwarding Rate from 10 Mbps ports: 14,880 pps max.
Processing type: Store and Forward, non-blocking

Auto-learning: 2K address table
Address buffer age-out time: 300 sec.
Packet buffers memory: 128KB,dynamically shared on all domains
(Non-blocking switching)
Latency (not including packet time): 100 to 10 Mbps: 5µs
10 to 100Mbps: 5µs
Path Delay Value: 50 BT on all ports

Maximum Ethernet Segment (or Domain) Lengths
10BASE-T (Unshielded twisted pair) - 100 m (328 ft)
100BASE-TX (CAT 5 UTP) - 100 m (328 ft)

www GarrettCom com

..

2

S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06)

Operating Environment

Ambient Temperature (S14): 32ºF to 104ºF (0ºC to 40ºC)

(S14H): -13ºF to 140ºF (-25ºC to 60ºC)
Long term per independent agency tests (UL)

-40ºF to 167ºF (-40ºC to 75ºC)
Short term per IEC Type tests
(S14P & PS14P): -40ºF to 185ºF (-40ºC to 85ºC)
Long term per independent agency tests (UL)

-40ºF to 167ºF (-40ºC to 75ºC)
Short term per IEC Type tests
Storage Temperature, All models: -40ºF to 185ºF (-40ºC to 85ºC)

Cold Start: (S14H) model to -20ºC
(S14P) model to -40ºC
Ambient Relative Humidity: 5% to 95% (non-condensing)
Altitude (All models): -200 to 5000ft. (-60 – 15,000 m)
Conformal Coating (optional) Humidity protection

www GarrettCom com

..

3

S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06)

Note: H and P models are designed for NEBS compliance, including, vibration, shock and

altitude.

Packaging:

Enclosure: Robust sheet metal (Steel).
Dimensions, Switch unit: Height x Width x Depth
S14, S14H, S14P & PS14P: 3.5 in H x 3.0 in W x 1.0 in D (8.9 cm x 7.6 cm x

2.5 cm)

Weight: all S14 models: 4.6 oz. (130g);

power supply, –d, and i: 5.9 oz (170g)

–Hd, and Hi: 5.8 oz (165g)

–Pd, and =Pi: 7.9 oz (225g)
PS14P units: 9.6 oz (272g)

Cooling Method: Convection on regular model, plus the case is used as a heat sink on
“H” and “P” models.

www GarrettCom com

..

4

S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06)

POWER SUPPLY (S14 Model only)

These products are intended to be supplied by a Listed, Direct Plug-In power unit, marked
“Class 2”, or a Listed ITE Power Supply, marked “LPS”, which has suitably rated output
voltage (i.e. 9vdc, 12vdc, 24vdc, 48vdc), and suitably rated output current (i.e. 100mA to
500mA).When connected to a 48 V centralized dc source these products shall be provided
with a Listed 5 A DC fuse in the supply circuit.

UL listed class II Power Supply, ( AC External):

Power input (8-15)V DC, jack is 2.5mm center +ve , with 6ft. cord
Input: 120vac at 60 Hz for “d” models, 240vac at 50Hz for “i” models that have IEC320
power connector built-in the PS unit. Out put- 12vdc, 1 Amps

Input: 100-240V AC at 47-63Hz, for “-Hd” high temp., 100-240V AC at 47-63Hz “-for
Hi” models that have IEC320 power connector built-in the PS unit.
Out put- 12vdc, 1.25 Amps

Input: 100-240V AC at 47-63Hz, for “-Pd” high temp. 100-240V AC at 47-63Hz, “-Pi”
models that have IEC320 power connector built-in the PS unit.
Out put- 12vdc, 2 Amps

www GarrettCom com

..

5

S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06)

DC to unit: 12V DC, 2.5mm jack, center +ve, 6ft. cord
Power Supply ( Direct DC ): built-in screw terminal
block for +, -, ground. The 12V DC jack is also present.

12V DC internal (range of 8.0 to 15V DC),

24V DC internal (range of 18 to 36V DC)

-48V DC internal (range of 36 to 60V DC) t.
Power Consumption: 3 watts typical, 4 watts max.

Note 1: 8-15V DC can be used for dual source DC input
Note 2: Internal DC power floats, user may ground “+” or “-” if desired.

POWER INPUT: (PS14P(POE) unit only)

Total Power Consumption: 66 watts max. (1.4A @48VDC)

www GarrettCom com

..

6

S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06)

Terminal block for -48v DC input (range of 46 to 60V dc), built in for +, - , ground. The 8­15V DC jack is also present, but it can only be used to power the PS14P unit itself, not PoE
devices attached.

POWER OUTPUT: (PS14P(POE) unit only)

PoE available on all four RJ-45 ports via Ethernet twisted pair cabling on port pins using
spare pairs 4,5(+) 7,8(-), not the data pair 1,2(-), 3,6(+)
802,3af Power Consumption: 61.6 watts max. (15.4(max)/port)
PoE Ports Output voltage: 44 to 57 VDC
Over Current Protection, per port: resettable fuse

Port Connectors:

RJ-45 Port: Auto-cross(MDIX), 100BASE-TX and 10BASE-T:shielded 8-pin
female. Three RJ-45 ports provided in front, and one on the rear. Supports shielded
(STP) and unshielded (UTP) Cat 3, 4, 5 cable. For PoE pass-through option on P
models, use Model # PS14P.

www GarrettCom com

..

7

S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06)

LED Indicators (Dual- front and end, port #4 has front only)

POWER: Steady ON when power applied (S14 model)

ON for -48V power applied to the PS14P unit
PoE, ports 1,2,3,4: ON when delivering power (PS14P)
10/100: = 100Mbps; OFF = 10 Mbps
LK/ACT: Steady ON for LINK with no traffic, blinking indicates port

is transmitting / receiving.

F/H: ON = full-duplex, OFF = half-duplex

Mounting option for S14 Family of Switches:
Metal Mounting clips for panel mounting : included

DIN-Rail mounting option: Model # DIN-RAIL MC2 (see Section 3.4)
Rack-mount option: MC14-TRAY, see

Mean Tine Between Failure (MTBF) – 15+ years, Telcordia (Bellcore SR-332) Method

www GarrettCom com

..

http://www.garrettcom.com/mc_tray.htm

8

S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06)

Agency Approvals and Standard Compliance:

UL Listed (UL 60950), cUL, CE, Emissions meet FCC Part 15, Class A.
NEBS L3 and ETSI compliant
H & P models: IEEE P1613 Env. Std for Electric Power Substations
P model: NEMA TS-2 and TEES for traffic control equipment
P model: designed for UL 2043 above-the-ceiling installation
IEC61850 EMC and Operating Conditions Class C for Power Substations
Designed for above-the-ceiling (plenum) installation

Warranty: Three years, return to factory Made in USA

www GarrettCom com

..

9

S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06)

1.2 Summary of models and descriptions:

S14-d,i = four 10/100 RJ-45 ports Switch, for office and wiring closet env., ext. AC Pwr Supply
S14H-Hd, Hi = Hardened, four 10/100 RJ-45 ports Switch, Factory floor, Int. 8-15VDC,

S14H-12VDC = Same as S14H model, except Ext. AC Hardened power supply not included
S14H-24VDC = Same as S14H-12VDC model, except for 24VDC power input
S14HR-24VDC = Same as S14H-24VDC model, but includes DIN-RAIL-MC2 option.
S14H-48VDC = Same as S14H-24VDC model, except for -48VDC power input.
S14P-Pd, Pi = ,Premium rated, four 10/100 RJ-45 ports Switch, for un-controlled(outdoor) env.

S14P-12VDC = Same as S14P-Pd, Pi, except ext. AC Premium Power Supply is not included.
S14P-24VDC = Same as S14P-12VDC model, except Ext. AC Premium power supply not included
S14PR-24VDC = Same as S14P-24VDC model, but includes DIN-RAIL-MC2 option.
S14P-48VDC = Same as S14P-24VDC model, except for -48VDC input
MC14-TRAY = 19” Rack-mount tray for 14-series Switch models, up to 16 units

DIN-RAIL-MC2 = Metal DIN-Rail mounting bracket for one S14-Series

www GarrettCom com

Ext. AC Hardened power supply included .

Int. 8 to 15V terminal block, Ext. AC Premium-rated Power Supply included.

..

10

S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06)

Magnum PS14P (PoE) Power Source Switch (model and descriptions)

PS14P = ,Premium rated, four 10/100 RJ-45 ports Switch in a compact package, rated for un­controlled(outdoor) env. All four RJ-45 Ethernet ports support Power Source PoE as per the IEEE

802.3ad standard. Includes integral -48V DC terminal block for power unit.

NOTE: If you want a heavy-duty Industrial power supply that plugs into AC and delivers -48BDC at
50 watts to support one PS14P-48VDC Switch and up to 4 attached PoE devices, Try this URL –

http://www.lanstore.com/ps.htm

MC14-TRAY = 19” Rack-mount tray for 14-series Switch models

DIN-RAIL-MC2 = Metal DIN-Rail mounting bracket for one PS14P Switch

2.0 INTRODUCTION

This section describes S14-Series models, including appearance, features and

typical applications.

www GarrettCom com

..

11

S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06)

2.1 Inspecting the Package and the Product

Examine the shipping container for obvious damage prior to installing this
product; notify the carrier immediately of any damage which you believe occurred during
shipment or delivery. Inspect the contents of this package for any signs of damage and
ensure that the items listed below are included.

This package should contain:
1 Magnum S14-Series or PS14P Switch Unit

1 External Power Supply, (for S14, S14H, S14P), (d, i model only)
1 set Metal panel mounting clips and screws, 2 each
1 User Guide, i.e., this manual

www GarrettCom com

..

12

(continued next page)

S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06)

Remove the Magnum S14-Series Switch from the shipping container. Be sure to keep the
shipping container should you need to ship the unit at a later date.
In the event there are items missing or damaged contact your supplier. If you need to
return the unit use the original shipping container. Refer to Section 5 Troubleshooting, for
specific return procedures.

2.2 Product Descri ption

The Magnum S14 family of Convenient Switches covers the full range of

application environments, with regular (office), Hardened (factory floor), and Premium­rated (outdoor) versions. Extra features for heavy-duty and extended temperature operation
ranges are included selectively in the Hardened factory-floor and Premium-rated outdoor
models. Input power may be AC, or DC at 12V, 24V or –48V, providing a selection for
office or for heavy duty industrial applications. This selection of models offers the best
price / value unit for each user and installation.

For any user who needs a small chunk of Ethernet connectivity, a 4-port “go

anywhere” Magnum S14 Switch is a versatile and handy solution, and can provide it in a
convenient compact package.

www GarrettCom com

..

13

S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06)

W

W

W

.

G

a

r

r

e

t

tC

o

m

.

C

o

m

LA3

PWR

F/H

PORT 4

PORT 2

PORT 1

10/100

10/100

LK/ACT

POWER

GarrettCom

10/100

LK/ACT

PORT 4

Magnum S14

Convenient Switch

9VDC. 1AMP

GarrettCom Magnum S14

Convenient Switch

10/100

LK/ACT

LK/ACT

PORT 3

3

PORT 3

PORT 2

PORT 1

2

LA2

LA1

1

Fig2.2a. Magnum S14, Front view (three RJ-45 ports on Front
side of the unit, as shown in Fig

10/

100

Fig. 2.2b

Fig2.2b. Magnum S14, Rear view (one RJ-45 port on rear

GarrettCom S14
Left Side View

8 –15V DC

side)

Fig 2.2a

www GarrettCom com

..

14

S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06)

The Yellow label S14 shown above are for office and wiring closet environments and use
an external AC power supply. A metal case with convection cooling is featured. Operation
may be in 0° to 50°C ambient temperature. The units can be mounted securely on a closet
wall or metal cabinet, or by using the metal panel mounting clips included.

The orange-label Magnum S14H as shown above in Fig 2.2c is a
hardened unit designed for factory floor and other industrial applications. The S14H models
are built with high-grade components and use special thermal techniques and a rugged
metal case for extended temperature industrial applications. The S14H Hardened unit
features a sealed metal case that is also used as a heat sink. No air inflow is required for
cooling, so the S14H resists dust, dirt, moisture, smoke and insects, and is above-the-ceiling
(plenum) rated. Choices of models for external AC or internal DC power are available.

www GarrettCom com

..

15

S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06)

W

W

W

.

G

a

r

r

e

t

t

C

o

m

.

C

o

m

M

a

g

n

u

m

S

1

4

H

C

o

n

v

e

n

i

e

n

t

S

w

i

t

c

h

g

Ambient temperature rating is up to –25°C to +60°C for any of the power input types, AC
or DC.

PORT 4

PORT 4

LK/ACT

9VDC. 1AMP

10/100

10/100

10/100

LK/ACT

POWER

PORT 2

PORT 1

GarrettCom

H

a

r

d

e

n

LA3

PWR

F/H

10/100

LK/ACT

LK/ACT

PORT 3

e

d

3

PORT 3

PORT 2

PORT 1

2

LA2

LA1

1

10/

100

Fig 2.2c- Magnum S14H, Front view (three RJ-45 ports on Front

10/

100

Fig 2.2d

LA4 4

F/H

GarrettCom S14

Left Side View

+ -

8 – 15V DC

side of the unit, as shown in Fig.

GarrettCom Magnum S14H

Hardened Convenient Switch

2.2c

Fi

www GarrettCom com

..

Fig2.2d. Magnum S14H, Rear view (one RJ-45 port and DC option on

rear side) as shown in Fig.

16