GarrettCom P62F User Manual
Magnum P62-Series
(P62F and managed mP62 models) Hardened Ethernet Switches
Installation and User Guide
www GarrettCom com
..
Magnum P62-Series Hardened Switches Installation and User Guide (12/02)
Magnum
P62-Series
(P62F and managed mP62 models)
Hardened Ethernet Switches
Installation and User Guide
Part #: 84-00092, (Rev F 12/02)
Trademarks
Ethernet is a trademark of Xerox Co rporation
NEBS is a trademark of Telcordia Technologies
UL is a registered trademark of Underwriters Laboratories
GarrettCom, Magnum, Personal Switch, and Link-L oss-Learn (patent pending) are
trademarks and Personal Hub is a registered tr ademark of GarrettCom, Inc.
Important: The Magnum P62-Series Hardened Ethernet Switches contain no user
serviceable parts. Attempted service by unauthorized personnel shall render all
warranties null and void. If problems are experienced with a Magnum P62-Series
Hardened Switch product, consult Section 5, Troubleshooting, of this User Guide.
Copyright 2002 GarrettCom, Inc. All rights reserved. No part
of this publication may be reproduced without prior written permission from
GarrettCom, Inc.
Printed in the United States of America.
www GarrettCom com
..
i
Magnum P62-Series Hardened Switches Installation and User Guide (12/02)
Contacting GarrettCom, Inc
Please use the mailing address, phone and fax numbers and email address listed below:
GarrettCom, Inc.
213 Hammond Ave.
Fremont, CA 94539
Phone (510) 438-9071
Fax (510) 438-9072
Website: http://www.GarrettCom.com
email support@garrettcom.com
Federal Communications Commission
Radio Frequency Interference Statement
This equipment generates, uses and can radiate frequency energy and if not installed
and used properly, that is in strict accordance with the manufacturer's instructions, may cause
interference to radio communication. It has been tested and found to comply with the limits for
a Class A computing device in accordance with the specifications in Subpart J of Part 15 of
FCC rules, which are designed to provide reasonable protection against such interference
when operated in a commercial environment. Operation of this equipment in a residential
area is likely to cause interference, in which case the users at their own expense will be
required to take wh atever measures may be required to correct the interference.
www GarrettCom com
..
ii
Magnum P62-Series Hardened Switches Installation and User Guide (12/02)
MAGNUM
ETHERNET CONNECTIVITY PRODUCTS
"DESIGNED AND MANUFACTURED IN THE USA"
Overview
GarrettCom, Inc. offers the Magnum line of Ethernet LAN connectivity products
with industry-standard functionality. Magnum products are heavy duty, feature
fiber-built-in ports, and have AC and DC power options to make them suitable for
a variety of Industrial and Carrier Class applications.
6K25 Managed Fiber Switches, Gigabit, 100 and 10 Mbps, fiber and copper ports, mixand match. Features SFF fiber for up to 25 fiber ports in a 1U unit. Configurable.
4K-Series Swit ches, 100 and 10 Mbps copper ports with optional 100Mb fiber ports,
regular and Reverse rack-mount models, AC and DC power options, heavy duty specs.
Quad-Series Fiber Switches, 100 & 10Mbps, fiber and copper ports, mixed-speed and
mixed-media types, full switching performance, AC and DC power options.
P62-Series “Outdoor” Ethernet Sw itches, for temperature uncontrolled applications,
6 10/100 and 2 100Mb fiber ports, managed and unmanaged models, all fiber types.
Mixed- Media Fiber Hub, 16-port Stackable,10/100 auto-sensing, AC and DC power
Dual Speed 8-port and 16-port Stackables, 10/100 auto-sensing. AC and DC power
cPCI Blade 12-port 10/100 “hub-on-a-card” for Compact PCI chassis rear I/O
ITS Blade 8-port 10/100 “switch-on-a-card” for Model 2070 Traffic Controller Chassis
Stackable Hubs, SNMP Opt ional
10Mb series and 100Mb series, both w/ optional port modules, AC and DC power
Personal Switches, 10/100Mb
8 port dual speed, Auto-negotiable with fiber option
Personal Hubs, 100Mb or 10/100Mb
8-port, with two switched ports (1 fiber built in)
Personal Hubs, 10Mb series
8-port + AUI, stackable to 5 high, + optional BNC of fiber port
8 or 9-port and 4 or 5-Port Personal Hubs, w/ man. up-link sw.
Media Converters, 10Mb and 100Mb series, for offices and Hardened models for
industrial applications. All media combinations, incl. fiber ST, SC, mm., single mode
The “X-line” of configurable MiXed Media products:
Stackable Concentrators, SNMP optional, 13-Ports
Repeater Port Modules (RPMs), 6 types for Ethernet media
Bridge Port Modules (BPMs), 4 types, for segment isolation
Transceivers, 10Mb series Mini-Transceivers and Coax Models Dec, 02
www GarrettCom com
..
iii
Magnum P62-Series Hardened Switches Installation and User Guide (12/02)
TABLE OF CONTENTS PAGE
1.0 SPECIFICATIONS.............................................................................................2
1.1 Technical Specifications...................................................................................2
1.2 Ordering Information........................................................................................5
2.0 INTRODUCTION................................................................................................7
2.1 Inspecting the Package and Product..................................................................7
2.2 Product Description..........................................................................................8
2.2.1 Magnum P62-Series chassis w/fiber SC (m.m. or s.m) connectors..........9
2.2.2 Managed mP62 chassis with fiber SC (m.m. or single-mode) ports...10
2.2.3 Managed Network Software ( MNS-mP ) for Magnum mP62 ..............11
2.2.4 Connecting the Console Terminal to Magnum mP62 (Management)...12
2.3 Fiber port, SC Connectors ..............................................................................13
2.4 Frame Buffering and Latency..........................................................................13
2.5 Features and Benefits......................................................................................15
2.6 Applications....................................................................................................16
3.0 INSTALLATION...............................................................................................19
3.1 Locating Magnum P62F-Series 10/100Mb Ethernet Switches.......................19
3.1.1 Mounting position and materials............................................................19
3.1.2 Mounting dimensions.............................................................................19
3.2 Connecting Ethernet Media, and Special Strain-relief feature........................21
3.2.1 Connect Twist Pair (RJ-45, CAT 3 or CAT 5, Unshield or Shield)......21
3.2.2 Connecting Fiber Optic SC-type, "Snap-In"..........................................22
3.2.3 Connecting Fiber Optic ST-type, “Snap-In” (Optional).........................22
3.2.4 Connecting Single-Mode Fiber Optic....................................................22
3.2.5 Power Budget Calculations for P62-Series Fiber Media........................23
3.2.6 Connections to NICs which support Auto-Negotiation, RJ-45 ports....24
3.3 Powering the Magnum P62-Series Hardened Switch.....................................24
3.3.1 Power P62F and mP62 models, for –48V and 24V DC pwr input ........24
3.3.2 Power the P62-5V models w/Ext AC Power Supply (PSX-A)..............25
3.3.3 Power the P62-5V w/DC Pwr Supply (PSX-T) at 125/250 VDC.........25
3.4 Cable Strain Relief Feature on all P62-Series models ....................................27
4.0 OPERATION.....................................................................................................28
4.1 Dual-Speed Functionality, and Switching.......................................................28
4.2 Auto-negotiation and Speed-sensing ..............................................................29
4.3 LED’s for P62-Series Hardened Switch......................................................29
5.0 TROUBLESHOOTING ....................................................................................30
5.1 Before Calling for Assistance .........................................................................30
5.2 When Calling for Assistance...........................................................................31
5.3 Return Material Authorization (RMA) Procedure..........................................31
5.4 Shipping and Packaging Information..............................................................32
APPENDIX A: WARRANTY INFORMATION........................................................32
Rev F 11/02 : This revision adds the Managed mP62 models.
Rev E 06/02 : Changed Altitude spec, and added Mechanical mounting drawing in 3.1.2.
Rev D 01 / 02: This revision changes the installation proc. and operating Temp. range.
Rev
C 11/01: This revision includes the magnum P62F-NOF, and metal mounting.
Rev B 08/01: This revision includes the update of additional power source
Rev A 04/01: This revision is the initial release of the P62F Hardened Switches user manual.
www GarrettCom com
..
1
Magnum P62-Series Hardened Switches Installation and User Guide (12/02)
1.0 SPECIFICATIONS
1.1 Technical Specifications
Ports Performance
Fiber, and when an auto-negotiating port is operating at 100Mbps:
Data Rate: 100Mbps
When an RJ-45 auto-negotiating port is operating at 10 Mbps:
Data Rate: 10 Mbps
For mP62 models, RJ-45 ports are S/W controlled for speed and F/H
duplex, crossover (MDI – MDIX) is automatically handled
Network Standards
100Mb: Ethernet IEEE 802.3u, 100BASE-TX, 100BASE-FX
10 Mb: Ethernet IEEE 802.3, 10BASE-T
Auto-sensing for speed: IEEE 802.3u; 802.3x flow control
For managed mP62 models, IEEE 802.1p QoS and 802.1d Spanning Tree
For mP62 management software , see Section 2.2.3
Packet-Processing Between Domains is non-blocking
Filtering and Forwarding Rate from 100Mbps ports: 148,800 pps max
Filtering and Forwarding Rate from 10 Mbps ports: 14,880 pps max.
Processing type: Store and Forward
Auto-learning: 4K address table (16K on P62F), shared for all ports
Packet buffers: 256KB, dynamically shared on all domains
Latency (not including packet time): 100 to 10 Mbps: 5
10 to 100Mbps: 5
µs
µs
Path Delay Value: 50 BT on all ports
Maximum Ethernet Segment (or Domain) Lengths
10BASE-T (Unshielded twisted pair) - 100 m (328 ft)
100BASE-TX (CAT 5 UTP) - 100 m (328 ft)
100BASE-FX, full-duplex: (multi-mode) - 2.0 km (6,562 ft)
100BASE-FX, full-duplex: (single-mode) - 20.0 km (65,620 ft)
100BASE-FX, full-duplex: (single-mode, long) - 40.0 km (131,240 ft)
Operating Environment
Ambient Temperature: -40°F to 170°F for mP62 (160°F for P62F)
(-40°C to 75°C for mP62, 70°C for P62F))
Cold start down to -20°C
Storage Temperature: -40° to 185°F (-40°C to 85 °C)
Ambient Relative Humidity: 5% to 95% (non-condensing)
Altitude: -200 to 50,00 ft. (-60 to 15,000m)
“Plenum rated” per UL2043 fire tests
IEC 529 rated IP51 (holds out dust, vertical water)
Operating Shock and Vibration: Meets Bellcore GR-63-CORE
Conformal coating (tropical humidity protection) optional, request quote
www GarrettCom com
..
2
Magnum P62-Series Hardened Switches Installation and User Guide (12/02)
Power Supply (Internal) 24VDC and -48VDC Power Supply
Power Input Voltage: 20 to 70 VDC (auto-ranging), “-, GND, +”
Power Consumption: 10 watts typical.
DC-DC Converter Rating: 5VDC, 2 Amps
Power Supply (Ext.) 125VDC & 250VDC, (PSX-T) for P62-Series -5V only
Power Input Voltage: 100 to 275 VDC (nominal rating of 125, 250VDC)
Power Consumption: 15 watts typical.
DC-DC Converter Rating: 5VDC, 3 Amps
Power Supply (External) AC Power Supply (PSX-A) for P62F-5V and mP62-5V
AC Power Connector: IEC-type, male recessed at rear of Power Supply chassis
Input Voltage: 85 to 264 VAC (auto-ranging)
Input Frequency: 47 to 63 Hz (auto-ranging)
Power Consumption: 15 watts typical
Power Supply Rating: 3Amps at 5VDC
Network Cable Connectors -6 RJ-45 shielded female ports and 2 fiber port
100Mbps: Category 5 UTP/STP, fiber (50/125, 62.5/125 mm, or single-mode at
9/125 micron)
10 Mbps: Category 3, 4, 5 UTP (Note: auto-sensing does not sense cable type)
Full-duplex / Half -duplex on copper (RJ-45) switched Ports # 2 to 7
All the RJ-45 ports support Full / Half duplex and 10/100 speed, each inde-
pendently auto-negotiating on P62F models; S/W controlled on mP62 models.
Fiber Ports # 1 and 8
The switched fiber ports # 1 & 8 are fixed at full-duplex only, 100Mb speed.
Mechanical
Enclosure: Rugged 18-gauge high-strength steel case. Metal mounting plate
included. Suitable for stand-alone, shelf, pedestal or wall mounting. The case also
serves as a heat sink. The metal mounting base is included, 13-guage steel.
(Without the base, the box size is only 7” high). Mounting holes in the base plate
are a rectangle that measures 3.35 ” x 7.92” (8.5 x 20.1 cm) center to center.
See Section 3.1.2 for additional mounting details.
Dimensions (wall mounted): 1.70 in D x 5.75 in W x 8.8 in H
(4.3 cm x 14.6 cm x 22.4 cm)
Weight: 3.5 lb. (1.6 kg.)
Cooling method: Convection, with case operating as a heat sink.
Note: Internal thermal materials and techniques (patent pending) conduct heat from
the electronic elements insi de to the steel case which acts as a heat sink. Int ernal
chip temperatures are only about 10°C above case ambient at steady state operation
LED Indicators
PWR: Steady ON when power applied
SPEED: (when LINK is ON): ON = 100Mbps; OFF = 10 Mbps
LINK/ACT: Steady ON for LINK with no traffic, blinking indicates port
is transmitting / receiving.
F/H (RJ-45 ports only): ON = full-duplex, OFF = half-duplex
www GarrettCom com
..
3
Magnum P62-Series Hardened Switches Installation and User Guide (12/02)
MTBF (Bellcore method)
Over 10 years MTBF. Email sales@GarrettCom.com for details
Agency Approvals
UL Listed (UL 60950), cUL, CB, CE Low Volt. Dir. & Electro-Magnetic Comp.
IEEE P1613 (Draft) Environmental Standard for Electric Power Subs. (C37.90)
Emissions: meets FCC Part 15, Class A, and ETSI
UL2043 fire tests for “plenum rating”.
Warranty: Three years, return to factory Made in USA
www GarrettCom com
..
4
Magnum P62-Series Hardened Switches Installation and User Guide (12/02)
1.2 Ordering Information
Magnum P62-Series, 10/100 Ethernet Switch
Magnum P62F-AC-2MSC: P62F-AC Ethernet Switch with six 10/100 RJ-45 and two
100Mb FDX fiber multi-mode SC-type ports. Has 16KB address table and 1.0 MB packet
buffers. AC power input, 85-160vac 47-63Hz worldwide auto-ranging via PSX-A power
source Extended Temp ( a separate unit). Steel case used as a heat sink, desi gned for use in
environmentally challenged locations such as “outdoors” with extended temperatures.
Magnum P62F-AC-1MISSC: Same as P62F-AC-2MSC, except one fiber port is 20km
single-mode SC. (includes PSX-A unit)
Magnum P62F-AC-2SSC: Same as P62F-AC-2MSC, except both fiber ports are 20km
single-mode SC. (includes PSX-A unit)
Magnum P62F-AC-NOF: P62F-DC Ethernet Switch, six 10/100 RJ-45 and no fiber
ports. Has 16KB address table and 1.0MB packet buffers. AC power input 85260vac 47-63Hz worldwide auto-ranging, via PSX-A Power Source Extended
Temp (a separate unit). Steel case used as a heat sink, designed for use in
environmentally auto-ranging. Steel case used as a heat sink, designed for use in
environmentally challenged locations such as “outdoors” with extended temperatures.
Magnum P62F-2MSC: 8-port Ethernet Switch with two 100Mbps full-duplex switched
fiber ports (multi-mode SC-type connector), and six half- or full-duplex switched
RJ-45 10/100 auto-negotiating ports. Includes store-and-forward switching that
filters and forwards data moving between the ports. The internal switch has 16K
nodes address table and 1MB packet buffers. DC power input, 18-70VDC autoranging. Steel case acts as a heat sink. Rated for extended temperature.
Magnum P62F-1M1SSC: Same as P62F-2MSC, but with one multi-mode SC-type and
one 20Km single mode SC fiber connectors.
Magnum P62F-2SSC: Same as P62F but with two 20Km sgl-mode SC-type fiber ports
Magnum P62F-NOF: P62F-DC Ethernet Switch, six 10/100 RJ-45 and no fiber ports.
Has 16KB address table and 1.0MB packet buffers. DC power input, 18-70VDC
auto-ranging. Steel case used as a heat sink, designed for use in environmentally
challenged locations such as “outdoors” with extended temperatures.
Parts
Magnum P62F-5V-2MSC: Same as P62F-2MSC, except with 5VDC input using
military-type-screw-lock connector.
Magnum P62F-5V-1M1SSC: Same as P62F-1,1SSC, except with 5VDC input using
military-type-screw-lock connector.
Magnum P62F-5V-2SSC: Same as P62F-2SSC, except with 5VDC input using
military-type-screw-lock connector.
Magnum P62F-5V-NOF: Same as P62F-NOF, except with 5VFC input via PSX-A
using military-type screw lock connectors.
Magnum PSX-5V-CBL (spare): 2-ft power cord with military type screw-lock
connector, spare for PSX to P62F-5V power cord.
Magnum PSX-A: P62F-5V Power Source for Extended Temperature, nominal AC
input 115-240vac at 47-63HZ auto-ranging, 15 watts, 5VDC output at 3Amps.
Steel case used as a heat sink. Extended temperature rated. Output power cord
has military-style screw-lock plug. Mounts as a separate unit adjacent to a
Magnum Model P62F-5V Switch.
Magnum PSX-T: Same as PSX-A , except 125VDC to 250VDC input, terminal lugs
for “+”, “-“, and GND
www GarrettCom com
..
5
Magnum P62-Series Hardened Switches Installation and User Guide (12/02)
Managed P62-Series (mP62) Hardened Switches
Magnum mP62-AC-2MSC: mP62-AC Managed Switch with six10/100 RJ-45 and two
100Mb FDX fiber multi-mode SC-type ports. Software includes menu-driven user
interface for ease of use, SNMP, QoS, Telnet, Security, STP, VLAN, BootP/DHCP. Has
4Knodes address table and 256K packet buffers. AC power input, 85-260vac 47-63Hz
worldwide auto-ranging, via PSX-A Power Source Extended Temp (a separate unit). Steel
case used a s a heat sink, designed for use in environmentally challenged location such as
“outdoors” with extended temperatures.
Magnum mP62-AC -1MISSC: Same as mP62-AC-2MSC, except one fiber port is 20km
single-mode SC. (includes PSX-A)
Magnum mP62-AC -2SSC: Same as mP62-AC-2MSC, except both fiber ports are 20km
single-mode SC. (includes PSX-A)
Magnum mP62-AC -NOF: mP62 –AC Ethernet Switch w/ six 10/100 RJ-45s, no fiber ports
Magnum mP62-2MSC: mP62-DC Ethernet Switch, six 10/100 RJ-45 and two 100Mb FDX
fiber multi-mode SC-type ports. Software and buffers same as mP62-AC-2MSC. Dc power
input, 18-70VDC auto-ranging
Magnum mP62-1MISSC: Same as mP62-2MSC, except one fiber port is 20km single-mode
SC. (No PSX unit required)
Magnum mP62-2SSC: Same as mP62-2MSC, except both fiber ports are 20km single-
mode SC. (No PSX unit required)
Parts
Magnum mP62-5V-2MSC*: Same as mP62-2MSC, except with 5VDC input using military-
type screw-lock connector
Magnum mP62-5V –1M1SSC*: Same as mP62-1M1SSC, except w/ 5VDC input using
military-type screw-lock connector
Magnum mP62-5V –2SSC*: Same as mP62-2SSC, except w/ 5VDC input using military-
type screw-lock connector
Magnum mP62-5V-NOF: Same as mP62-NOF, except w/ 5VDC input using military-type
screw-lock connector
Magnum PSX-5V-CBL (spare): 2ft. power cord with military –type screw-lock connector,
spare for PSX to mP62-5V power cord.
MST Conversion: Special Item, convert one standard P62-2MSC w/two MSC fiber ports to
two MST fiber ports.
*PSX unit or equal required to supply 5VDC input. For more information, see the P SX datasheet.
Magnum P62 models with other fiber connector types and combinations available, request quote.
GarrettCom, Inc. reserves the right to ch ange specifications, performance characteristics and /
or model offerings without notice.
www GarrettCom com
..
6
Magnum P62-Series Hardened Switches Installation and User Guide (12/02)
2.0 INTRODUCTION
2.1 Inspecting the Package and Product
Examine the shipping container for obvious damage prior to installing this product;
notify the carrier of any damage that you believe occurred during shipment or delivery. Inspect
the contents of th is package for any signs of damage and ensure that the items list ed below are
included.
This package should contain:
1 Magnum P62-Series Hardened Switch (P62F-xxx o r mP62-xxx)
1 Installation and User Guide
1 Product Registration Card
(Optional, if AC power)
1 PSX-A Power Source Extended Temp. unit
1 6 ft. long AC Power chord (for PSX-A Unit only)
(Optional, PSX-T, 125 or 250VDC)
1 PSX-T Power Source Extended Temp. unit
Remove the Magnum P62-Series Hardened Switch from the shipping container. Be
sure to keep the shipping container should you need to ship the unit at a later date. To validate
the product warranty, please complete and return the enclosed Product Registration Card to
GarrettCom, Inc. as soon as possible.
In the event there are items missing or damaged, contact your supplier. If you need to
return the unit, use the original shipping container. Refer to Chapter 5, Troubleshooting, for
specific return procedur es.
www GarrettCom com
..
7
Loading...