GarrettCom Magnum DS8016-A, Magnum DS8016-B, Magnum DS8016-E, Magnum DS8016-R Installation And User Manual

www GarrettCom com

..

Magnum DS8016

10 / 100Mb Dual-Speed

Stackable Hubs

Installation and User Guide

$5.00 USD

Magnum DS8016 Dual-Speed Stackable Hubs Installation and User Guide (07/06)

Magnum DS8016

10/100Mb Dual-Speed

Stackable Hubs

Installation and User Guide

Part #: 84-00120, Rev. C (04/01)

Trademarks
Ethernet is a trademark of Xerox Corporation
NEBS is a trademark of Telcordia Technologies
UL is a registered trademark of Underwriters Laboratories
GarrettCom, Magnum and Personal Switch are trademarks and Personal Hub is a

registered trademark of GarrettCom, Inc.

Important: The Magnum DS8016 10/100 Dual Speed Stackable Hubs family
contains no user serviceable parts. Attempted service by unauthorized personnel
shall render all warranties null and void. If problems are experienced with
Magnum DS8016 10/100 Dual Speed Stackable Hubs, consult Section 6,
Troubleshooting, of this User Guide.

Copyright  2006 GarrettCom, Inc. All rights reserved. No part
of this publication may be reproduced without prior written permission from
GarrettCom, Inc.

Printed in the United States of America.

i

www GarrettCom com

..

Magnum DS8016 Dual-Speed Stackable Hubs Installation and User Guide (07/06)

Contacting GarrettCom, Inc

Please use the mailing address, phone and fax numbers and email address listed below:

GarrettCom, Inc.

47823 Westinghouse Dr.

Fremont, CA 94539-7437

Phone [phone]

Fax [phone]

Website: http://www.GarrettCom.com

email [e-mail]

Federal Communications Commission

Radio Frequency Interference Statement

This equipment generates, uses and can radiate frequency energy and if not
installed and used properly, that is in strict accordance with the manufacturer's instructions,
may cause interference to radio communication. It has been tested and found to comply with
the limits for a Class A computing device in accordance with the specifications in Subpart J
of Part 15 of FCC rules, which are designed to provide reasonable protection against such
interference when operated in a commercial environment. Operation of this equipment in a
residential area is likely to cause interference, in which case the user at his own expense will
be required to take whatever measures may be required to correct the interference.

ii

www GarrettCom com

..

Magnum DS8016 Dual-Speed Stackable Hubs Installation and User Guide (07/06)

The Magnum Line

ETHERNET CONNECTIVITY PRODUCTS

"DESIGNED AND MANUFACTURED IN THE USA"

OVERVIEW

GarrettCom, Inc.offers the premium-quality Magnum line of Ethernet LAN
connectivity products with industry-standard functionality and built-in fiber
configurability. Magnum products are designed for use in demanding Carrier Class,
Industrial Grade and OEM applications where reliability is a primary consideration.

4K-Series Switches, 100 & 10Mbps, copper ports with optional fiber

port, with auto-negotiating full switching performance

Quad-Series Fiber Switches, 100 & 10Mbps, fiber and copper ports,
mixed-speed and mixed-media types, full switching performance

“Outdoor” Ethernet Switch, for temperature uncontrolled locations
6 10/100 and 2 100Mb fiber ports, can be connected in strings

Mixed-Media Fiber Hub, 16-port Stackable, 10/100 auto-sensing
Dual Speed 8-port and 16-port Stackables, 10/100 auto-sensing
Stackable Hubs, SNMP Optional

10Mb series and 100Mb series, both w/ optional port modules

Personal Switches

, 10/100Mb

8 port dual speed, Auto-negotiable with fiber option

Personal Hubs

, 100Mb or 10/100Mb

8-port, with two switched ports (1 fiber built in)
Personal Hubs, 10Mb series
8-port + AUI, stackable to 5 high, + optional BNC of fiber port

8 or 9-port and 4 or 5-Port Personal Hubs, w/ man. up-link sw.
Media Converters, 10Mb and 100Mb series

All media combinations, incl. fiber ST, SC, mm., single mode

The “X-line” of configurable MiXed Media products:
Stackable Concentrators, SNMP optional, 13-Ports
Mini-Concentrators, 7 Ports, Repeaters, 2-Ports

Repeater Port Modules (RPMs), 6 types for Ethernet media
Bridge Port Modules (BPMs), 4 types, for segment isolation

Fan-Outs, 10Mb series
2, 4 and 8 Port Models

Transceivers, 10Mb and 100Mb series 10Mb Mini-Transceivers and

Coax Models, All Types -

July, 06

iii

www GarrettCom com

..

Magnum DS8016 Dual-Speed Stackable Hubs Installation and User Guide (07/06)

iv

www GarrettCom com

..

TABLE OF CONTENTS PAGE 1

1.0

SPECIFICATIONS................................................................................ 1

1.1 Technical Specifications ......................................................................1

1.2 Ordering Information........................................................................... 3

2.0

INTRODUCTION.................................................................................. 4

2.1 Inspecting the Package and Product..................................................... 4

2.2

Product Description - General.......................................................... 5

2.2.1

Magnum DS8016 Chassis........................................................6

2.2.2

10 / 100 Speed Auto-sensing ................................................... 7

2.2.3: Magnum DS8016-E model, 100Mbps -only................................. 8

2.2.4: DS8016-R “reverse” model, front LEDs and conn in rear............8

2.3 Stacking Magnum DS8016s.................................................................9

2.4 Bridge Module between the 10Mb and 100Mb Domains..................10

2.5 Up-link, Port 1X for Cascading ........................................................ 10

2.6 Features and Benefits........................................................................ 11

2.7 Applications....................................................................................... 12

3.0

MAGNUM DS8016 INSTALLATION............................................... 15

3.1 Locating Magnum DS8016 Dual-Speed Hubs................................... 15

3.1.1

Table-Top or Shelf Mounting ................................................ 15

3.1.2 Rack-Mounting........................................................................ 16

3.2 Connecting Ethernet Media................................................................17

3.2.1

Connecting Twisted Pair ....................................................... 18

3.2.2

Attaching to the MII port in the rear......................................18

3.2.3

100Mbps Cable Distances and PDV Calculations................. 18

3.2.4

Connections to NICs which support Auto-Negotiation ......... 21

3.3 Powering the Magnum DS8016.........................................................21

4.0

OPERATION........................................................................................22

4.1 Dual-Speed and Domain-Switched Functionality.............................. 22

4.2 Auto-negotiation and speed-sensing ............................................. 25

4.3 LED’s............................................................................................ 25

4.4 Up-link Port 1X................................................................................. 26

5.0

TROUBLESHOOTING.......................................................................27

5.1 Before Calling for Assistance............................................................ 27

5.2 When Calling for Assistance.............................................................. 28

5.3 Return Material Authorization (RMA) Procedure.............................28

5.4 Shipping and Packaging Information................................................. 29

APPENDIX A: WARRANTY INFORMATION......................................... 29

APPENDIX B : OPTIONAL 48V DC POWER SUPPLY, ADDENDUM..30

APPENDIX C: OPTIONAL 48V DS DC POWER, ADDENDUM.............32

R07/06: Updated Rack-mounting and Appendix B & C with 24VDC and 125VDC Power
Supply Option as per UL instructions.

Rev C 04/01 : Change the company’s name to GarrettCom, Inc.(formerly it was Garrett
Communications). There are no changes made to the content material at this time.

Magnum DS8016 Dual-Speed Stackable Hubs Installation and User Guide (07/06)
Rev B 03/99 : Added Reverse model specifications and collision domain diameter, cable

distances and pdv calculations
Rev A 07/98 : This revision is the initial release of the DS8016 10/100 Dual Speed

Stackable Hubs user manual.

v

www GarrettCom com

..

Magnum DS8016 Dual-speed Stackable Hubs Installation and User Guide (04/01)

1

www GarrettCom com

..

1.0 SPECIFICATIONS

1.1 Technical Specifications

100 or 10 Mb/s per port, auto-sensing for speed. DS8016 hubs support

two traffic domains, one at 100Mb/s and one at 10Mb/s, have sixteen RJ- 45

ports, and are stackable up to 3 units high operating as one repeater. In
addition , a Media Independent Interface (MII) port is provided per unit
(except on -R “reverse” models)

Performance

When a port is operating at 100Mb/s:
Data Rate: 100 Mb/s
PDV (Path Delay Value) : 80BT, exceeds Class II
When a port is operating at 10Mb/s: Data Rate = 10 Mb/s

Partitioning: Enforced after 63 consecutive collisions
Auto-reconnect: Occurs after one packet of error-free reception

Network Standards

100Mb: Ethernet IEEE 802.3u , 100BASE-TX
10Mb: Ethernet IEEE 802.3, 10BASE-T
Auto-sensing for speed: IEEE 802.3u

Packet-Processing Between Domains (internal 10/100 switch or bridge)

Filtering and Forwarding Rate from 100Mb ports: 148,800 pps max.

Filtering and Forwarding Rate from 10 Mb ports: 14,880 pps max.
Processing type : Store and Forward

Auto-learning : 8K address table, shared for both traffic domains
Packet buffers : 2MB,dynamically allocated & shared on both domains
Latency (not including packet time) : 100 to 10Mb : 5s
10 to 100Mb : 5s
CPU Type : State Machine

Maximum Ethernet Segment (or Domain) Lengths
10BASE-T (Unshielded twisted pair) - 100 m (328 ft)

100BASE-TX (CAT 5 UTP) - 100 m (328 ft)
Operating Environment

Ambient Temperature: 32ºF to 122ºF (0ºC to 50ºC)

Storage Temperature: -20ºC to 70ºC
Ambient Relative Humidity : 5% to 95% (non-condensing)

Po wer Supply (Internal

)

AC Power connector : IEC-type, male recessed, rear of chassis
Power Input Voltage : 90 to 260 VAC (auto ranging)
Power Input Frequency : 47-63 Hz

Power consumption: 25 watts typical, 40 watts max. P.S. rating

Magnum DS8016 Dual-Speed Stackable Hubs Installation and User Guide (07/06)

2

www GarrettCom com

..

48VDC Power Supply (Optional

)

Power Input Voltage : 36 to 72 VDC (auto ranging)
Terminal Block in rear: “-, GND, +”

Power consumption: 25 watts typical, 40 watts max. P.S. rating

Network Cable Connectors - for the 16 RJ-45 shielded female ports per hub

100Mb: Category 5 UTP/STP
10Mb: Category 3, 4, 5 UTP (Note: speed-sensing does not sense cable type)
MII port: standard 40-pin female MII port connector in the rear (not on -R’s)

Stacking Cable - stacking may be up to three DS8016 hubs, or 48 RJ-45 ports. A

stacking cable with 25 pin DB-25 connectors, shielded, 9 inch (23 cm) long,
is included with each DS8016-A and -E Dual-Speed add-on unit. (No
stacking connectors are built into the DS8016-R “reverse” model).

Up-Link - Use first RJ-45 port, which has two connectors (only one can be used at

a time). Plug into # 1 for use as a regular user segment port, or into # 1X for
use as a cross-over (X position) up-link port for connection to a central hub or
another cascaded hub.

Packaging

Enclosure: High strength metal. Rack-mounting brackets included.
Suitable for wiring closet shelf, 19” rack or desktop mounting.
Dimensions: 1.75 in H x 17in. Wx9 in D ( 4.4cm x 43.2cm x 22.9cm)
Weight: 4.0 lb. ( 1.8 Kg)
Cooling method: Fan cooled, internal @ 9cfm
On-Off manual switch for AC or DC input power, located at power input

LED Indicators
PWR : Steady On when power applied
BR : Bridge Module Indicator, On when 10/100 bridge module is installed

(Model DS8016-B,R), Off when no bridge module is inside (-A and -E)
COL : Collision LEDs, one each for 100Mb and 10Mb speed domains
100/Auto: Speed LED, per port. Steady On when speed is 100Mbps , Off when

speed is 10Mb, flashing when auto-negotiating or not connected.
LK/RX : Activity LED per port. Steady On when twisted-pair link is
operational Activity, flashing when port is receiving data.

Agency Approvals
Safety :UL Listed (UL 1950), cUL, CE

Emissions: meets FCC Part 15, Class A
Warranty

Three years, return to factory Made in USA

Magnum DS8016 Dual-Speed Stackable Hubs Installation and User Guide (07/06)

3

www GarrettCom com

..

1.2 Ordering Information

Magnum DS8016 Dual-Speed Stackable Hubs

Magnum DS8016-A:

Dual-Speed 10/100 Stackable Hub with sixteen RJ-45ports, each
auto-sensing for 100Mb or 10Mb operation. Stackable up to three units high,
with all ports in one stack operating as two separate traffic domains, one domain
at 100Mb/s and one domain at 10Mb/s. Includes stacking cable, internal auto­ranging power-supply, cooling fan, and metal brackets for shelf or wall
mounting.

Magnum DS8016-B:

Same as Magnum DS8016-A but includes an internal switch
module that bridges the two traffic domains, filtering and selectively forwarding
packets between the 100Mb and the 10Mb domains. Stacks up to two DS8016­A units. One DS8016-B unit stack supports all ports at 100Mb or 10Mb
communicating with each other. The internal switch has 2Mb dynamic store­and-forward packet buffers and 8K node addresses.

Magnum DS8016-E:

Same as Magnum DS8016-A but all ports operate at 100Mbps
only(not dual speed-speed). Each port will auto-negotiate with an attached
10/100device for 100Mbps speed and half-duplex mode only. May be used in
DS8016 stacks, same as Model DS8016-A.

Magnum DS8016-R:

Same as Magnum DS8016-B but with all ports on the rear side
and all of the LEDs are on front panel. No stacking. Normally used with 48V
DC dual source power supply, mounted in telco racks.

RMB-23W: Set of two mounting brackets that extend a standard 19” DS8016 hub

for mounting in a 23” -wide telco rack, 1U high.

GarrettCom, Inc. reserves the right to change specifications, performance
characteristics and/or model offerings without notice.

Magnum DS8016 Dual-Speed Stackable Hubs Installation and User Guide (07/06)

4

www GarrettCom com

..

2.0 INTRODUCTION

2.1 Inspecting the Package and Product

Examine the shipping container for obvious damage prior to installing this product;
notify the carrier of any damage which you believe occurred during shipment or delivery.
Inspect the contents of this package for any signs of damage and ensure that the items listed
below are included.

This package should contain:

1 Magnum DS8016-series Dual-Speed Hub unit
1 AC Power Cord (U.S. and other 115 vac locations only)
1 Stacking Cable, Model

DS8016-A and -E add-on (no bridge inside) units only
1 Set of metal “Ears” for optional rack mounting
1 Installation and User Guide

1 Product Registration Card

Remove the Magnum DS8016 Dual-Speed Hub from the shipping container. Be

sure to keep the shipping container should you need to ship the unit at a later date. To
validate the product warranty please complete and return the enclosed Product Registration
Card to GarrettCom, Inc. as soon as possible.

In the event there are items missing or damaged contact your supplier. If you need
to return the unit use the original shipping container. Refer to Chapter 5, Troubleshooting,
for specific return procedures.

Magnum DS8016 Dual-Speed Stackable Hubs Installation and User Guide (07/06)

5

www GarrettCom com

..

2.2 Product Description - General

Magnum DS8016 Dual-Speed hubs have sixteen RJ-45 ports, each 10/100Mb auto­sensing *. Each port can independently identify (via IEEE 802.3u auto-sensing) and accept
either 100Mb or 10Mb Ethernet signals, adapting to match the best speed of the connected
device. There are two internal traffic domains in Magnum DS8016 hubs, one for the 100Mb
traffic and one for the 10Mb traffic. The 100Mb users share the 100Mb domain’s bandwidth
and the 10Mb users share the 10Mb domain’s bandwidth.

* Note:

the “special 100Mb-only” model DS8016-E is not dual-speed. See Section 2.2.3 below.

Any DS8016 port can connect into either the 100 or the 10Mb traffic domain, and
can also change from one traffic domain to the other at any time without affecting the speed
of other ports. The automatic per-port speed-sensing is continuous (it takes place at LINK
enable, see section 4.2 for details), allowing the connected devices to change speed at any
time without impairing the operation of the other ports and connected devices.

Stackabl e
Hub

9 1 0 11 12

10Mb Hub

100Mb Hub

DS8016A

Figure 2.2 a : Magnum DS8016s are functionally both a 10Mb and a 100Mb hub in one

As Magnum DS8016 Dual-Speed units are stacked, the two shared traffic domains
automatically expand to support all of the ports in the stack. Any combination of 10Mb and
100Mb ports, up to the maximum of 48 ports (3 units) in one stack, can be in use at any time.

Some DS8016 models, the Magnum DS8016-B and DS8016-R, include an internal
bridge or switch module which interconnects the 10 Mb and the 100Mb traffic domains. This
enables all users on a DS8016-B or -R hub or a DS8016 stack, whether 100Mb or 10Mb, to
talk to each other. The internal switch of the DS8016’s filters and selectively forwards
packets between the 10Mb and the 100Mb domains, maintaining peak performance in each
domain unaffected by local traffic in the other domain. The internal bridge is self-learning,
with large address table capacity for up to 8K node addresses. As networked nodes are
added or removed or move from one speed domain to the other, the DS8016-B’s (or DS8016­R’s) internal switch automatically keeps track.

PWR

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

1 2 3 4 5 6 7 8 9 10 1 1
12 13 14 15 16

X

UPLINK

LK/RX
PORT

100

2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

PWR

BR

COL 10
COL 100

Magnum DS8016 Stack ab le Hub

PWR

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16