GarrettCom Magnum CS14 Series, Magnum CSN14 Series Installation And User Manual

Magnum CS14 and CSN14 Converter Switches

CS14, CSN14 Series Converter Switch Installation and User Guide (02/06)

Magnum™ CS14 and CSN14 Series Converter Switch

Installation and User Guide

Part #: 84-00101 Rev. A

Trademarks
GarrettCom, Magnum, Link-Loss-Learn, S-Ring, Convenient Switch, Converter
Switch are trademarks and Personal Hub is a registered trademark of GarrettCom, Inc.

Ethernet is a trademark of Xerox Corporation
NEBS is a trademark of Telcordia Technologies

CS14, CSN14 Series Converter Switch Installation and User Guide (02/06)

Federal Communications Commission

Radio Frequency Interference Statement

This equipment generates, uses and can radiate frequency energy and if not
installed and used properly, that is in strict accordance with the manufacturer's
instructions, may cause interference to radio communication. It has been tested and
found to comply with the limits for a Class A computing device in accordance with the

CS14, CSN14 Series Converter Switch Installation and User Guide (02/06)

Contacting GarrettCom, Inc

Please use the mailing address, phone and fax numbers and email address listed below:

GarrettCom, Inc.

47823 Westinghouse Drive

Fremont, CA 94539

CS14, CSN14 Series Converter Switch Installation and User Guide (02/06)

TABLE OF CONTENTS Page

1.0 SPECIFICATIONS ............................................................................... 1

1.1 Technical Specifications..................................................................... 1

1.2 Summary of models and descriptions:.................................................. 11

2.0 INTRODUCTION ............................................................................... 14

2.1 Inspecting the Package and the Product............................................. 14

2.2 Product Description ........................................................................... 15

2.3 Frame Buffering and Latency............................................................ 23

CS14, CSN14 Series Converter Switch Installation and User Guide (02/06)

3.7 CS14H and P Series , DC-powered, Installation .............................. 48

3.8 Connecting Ethernet Media ............................................................... 49

3.8.1 Connecting Twisted Pair............................................................ 51

3.8.2 Connecting Fiber Optic ST-type, “twist-lock”........................... 52

3.8.3 Connecting Fiber Optic SC-type, "Snap-In".............................. 53

3.8.4 Connecting Single-Mode Fiber Optic........................................ 53

3.8.5 Power Budget Calculations for CS14 Series, Fiber Media........ 54

3.8.6 Connections to NICs which support Auto-Neg RJ-45 ports...... 56

CS14, CSN14 Series Converter Switch Installation and User Guide (02/06)

5.4 Shipping and Packaging Information................................................. 68

APPENDIX A: WARRANTY INFORMATION......................................... 69

Revisions
Rev A 02/06: Change address to Westinghouse Drive
Rev A 05/05: Minor updates on Auto-cross (MDIX) functionality
Rev A 10/04: Minor updates on power supply option.
Rev A 09/04: Minor updates on UL requirements, and edit.

CS14, CSN14 Series Converter Switches Installation and User Guide (02/06)

1.0 SPECIFICATIONS

1.1 Technical Specifications

Ports Performance

When a port is operating at 100Mbps:

Data Rate: 100Mbps
When a port is operating at 10 Mbps:
Data Rate: 10 Mbps

CS14, CSN14 Series Converter Switches Installation and User Guide (02/06)
Address buffer age-out time: 300 sec.

Packet buffers memory: 128KB, dynamically shared on all domains
Latency (not including packet time): 100 to 10 Mbps: 5µs
10 to 100Mbps: 15µs
Path Delay Value: 50 BT on all ports

Maximum Ethernet Segment (or Domain) Lengths

10BASE-T (Unshielded twisted pair) - 100 m (328 ft)
100BASE-TX (CAT 5 UTP) - 100 m (328 ft)

CS14, CSN14 Series Converter Switches Installation and User Guide (02/06)

Operating Environment

CS14, CSN14: 32ºF to 104ºF (0ºC to 40ºC)
CS14H, CSN14H: -13ºF to 140ºF (-25ºC to 60ºC) Long term per agency tests (UL).

-40ºF to 149ºF (-40ºC to 85ºC) Short term per IEC Type tests.
CS14P, CSN14P: -40ºF to 167ºF (-40ºC to 75ºC) Long term per agency tests (UL).

-58ºF to 212ºF (-50ºC to 100ºC) Short term per IEC Type tests.

Storage Temperature

,

All models: -40ºF to 160ºF (-40ºC to 85ºC)

CS14, CSN14 Series Converter Switches Installation and User Guide (02/06)

Packaging:

Enclosure: Rugged sheet metal (Steel).
Dimensions of the Switch unit:

3.5 in H x 3.0 in W x 1.0 in D (8.9 cm x 7.6 cm x 2.5 cm)

Weight: all models: 4.6 oz. (130g);

Power supply, –d, and i: 5.9 oz (170g)

–Hd, and Hi: 5.8 oz (165g)

CS14, CSN14 Series Converter Switches Installation and User Guide (02/06)

POWER SUPPLY

These products are intended to be supplied by a Listed, Direct Plug-In power unit, marked
“Class 2”, or a Listed ITE Power Supply, marked “LPS”, which has suitably rated output
voltage (i.e. 9vdc, 12vdc, 24vdc, 48vdc), and suitably rated output current (i.e. 100mA to
500mA).When connected to a 48 V centralized dc source these products shall be provided
with a Listed 5 A DC fuse in the supply circuit.

CS14, CSN14 Series Converter Switches Installation and User Guide (02/06)

International (-i) models. Input: 240vac at 50Hz with IEC 320 connector for the user
supplied AC power cord.
Output:12vdc, 1Amps

Factory Floor (H) Ratings

(-25 to 60°C)

North America (-Hd) models. Hardened, factory floor temperature rated. Input: 6ft AC

power cord to IEC 320 connector on the 100-240vac 47-63Hz external power adapter.
Output:12vdc, 1.25Amps
International (-Hi) models. Factory floor temperature rated. Input: IEC 320 connector on

CS14, CSN14 Series Converter Switches Installation and User Guide (02/06)

Direct DC POWER SUPPLY : built-in terminal block for +, -, ground along with
12VDC jack
12V DC internal (range of 8.0 to 15V DC),.

24V DC internal (range of 18 to 36V DC),.

-48V DC internal (range of 36 to 60V DC), , -, ground.

CS14, CSN14 Series Converter Switches Installation and User Guide (02/06)

Port Connectors

:

Two RJ-45 Ports: support 100BASE-TX and 10BASE-T with auto-cross (MDIX).
They are shielded 8-pin female connectors for shielded (STP) and unshielded
(UTP) Cat 3, 4, 5 cable.
One Fiber optic port: On the CSN14 Series it is 10Base-FL with ST connections
and on the CS14 series it is 100Base-FX with a “fiber flavor” choice of multimode

CS14, CSN14 Series Converter Switches Installation and User Guide (02/06)

LED Indicators (Dual: front and top)

POWER: Steady ON when power applied

10/100: Steady ON for 100Mbps; OFF for 10 Mbps

LK/ACT: Steady ON for LINK (LK) with no traffic, BLINKING indicates
port is transmitting / receiving (ACT).

F/H: Steady ON for full-duplex, OFF for half-duplex

Mounting options

CS14, CSN14 Series Converter Switches Installation and User Guide (02/06)

Agency Approvals and Standards Compliance:

UL Listed (UL 60950), cUL, CE,

Emissions meets FCC Part 15 Class A.

NEBS L3 and ETSI compliant.

H and P models: IEEE P1613 Env. Std for Electric Power Substations
P models: NEMA TS-2 and TEES for traffic control equipment
P models: designed for UL 2043 above-the-ceiling installation
IEC61850 EMC and Operating Conditions Class C Power Substations

CS14, CSN14 Series Converter Switches Installation and User Guide (02/06)

1.2 Summary of models and descriptions:

Note: The CSN14 model # consists of the base unit type and the power input. Insert S for sgl-mode
The CS14 model # consists of the base unit type, the fiber flavor (ff) and the power input.

CSN14 Models (for 10Mb fiber).
CSN14-d or -i = two 10/100 RJ-45+ one 10Mb ST Fiber port for office and wiring closet,
rated (0 to 40°C) using an external AC power supply.
CSN14H-Hd, Hi = Hardened (H), two RJ-45+ one 10Mb Fiber port for factory floor, rated
(-25 to 60°C) using a direct DC ( 8-15VDC) and/or external AC hardened power supply ( i ncluded).
CSN14H-12VDC = Same as CS14H model, except AC hardened power supply is not included

CS14, CSN14 Series Converter Switches Installation and User Guide (02/06)

CS14 Models (for 100Mb fiber).

CS14-ff-d or -i = two 10/100 RJ-45+ one 10Mb ST Fiber port for office and wir i ng closet
(0 to 40C) using an external AC power supply.
CS14H-ff-Hd, Hi = Hardened (H), two RJ-45+ one 10Mb Fiber port for factory floor
(-25 to 60C) using a direct DC ( 8-15VDC) and/or external AC hardened power
supply (included).
CS14H-ff-12VDC = Same as CS14H model, except AC hardened power supply is not included
CS14H-ff-24VDC = Same as CS14H-12VDC model, except 24VDC power input replaces 12VDC.
CS14HR-ff-24VDC = Same as CS14H-24VDC model, but includes DIN-RAIL-MC2 mounting option.

CS14, CSN14 Series Converter Switches Installation and User Guide (02/06)

“SC” = 100Base-FX-SC: multi-mode fiber optic with SC type connector, 2km.
“SSC”= 100Base-FX-SSC: single-mode fiber optic with SC type connector, 20km.
“SSCL”= 100Base-FX-SSCL: single-mode fiber optic with SC type connector, 40km.
“ST” = 100Base-FX-ST: multi-mode fiber optic with ST type connector, 2km.
“SST” = 100Base-FX-ST: single-mode fiber optic with ST type connector, 2km.
“SLC”= 100Base-FX-SLC: single-mode fiber optic with LC type connector , 15km.
“MTRJ”= 100Base-FX-MTRJ: multi-mode fiber optic with MTRJ type connector, 2km.

Accessories

CS14, CSN14 Series Converter Switches Installation and User Guide (02/06)

2.0 INTRODUCTION

This section describes CS14- and CSN14-Series models, including appearance,

features and typical applications.

2.1 Inspecting the Package and the Product

Examine the shipping container for obvious damage prior to installing this
product; notify the carrier immediately of any damage which you believe occurred during
shipment or delivery. Inspect the contents of this package for any signs of damage and
ensure that the items listed below are included.

CS14, CSN14 Series Converter Switches Installation and User Guide (02/06)

Remove the Magnum CS14 or CSN14 Series Converter Switch from the shipping
container. Be sure to keep the shipping container should you need to ship the unit at a later
date. In the event there are items missing or damaged contact your supplier. If you need to
return the unit, use the original shipping container. Refer to Section 5 Troubleshooting, for
specific return procedures.

2.2 Pr oduc t Description

Combine a 10 or 100 Mb Fiber Media Converter and a two-port 10/100 copper
Switch, and you have the Converter Switch, a flexible edge-of-the-network Ethernet

CS14, CSN14 Series Converter Switches Installation and User Guide (02/06)

heavy-duty and extended temperature operation ranges are included selectively in the
Hardened factory-floor and Premium-rated outdoor models. This selection of models and
fiber port types offers the best price-to-value ratio for each user and installation. Where a
Media Converter might have been used, a Converter Switch offers a better value. The
compact package is ideal for network edge installations, and is able to be conveniently
mounted to suit any application.