398200003Base Assembly (Includes items 22 - 28 & 30 - 33)111
493061040Induction Coil #61.04 with RTCS CU
Sensors and metal carrier
+
+98021768
+98021753
^
*
1072184020Upper Case “BH/BA”111
1177262001Ceran Glass 260 x 260 x 4mm111R C
11A70000001Silicone Gasket (for glass installation) 250x 6x 4mm444R C
1266000000Overlay111
1335624009LED 24V Green - Chrome111R
1494900070Step Switch With Cable111R C
1539400003Knob 0-9111R
2034120159Fuse SUT 15Amps 250V-6.3x32222R C
2134110019Fuse T1.0A111R C
2239500003Screw Nut PG 16111
2339500009Screwed Cable Gland PG 16111
24A38614035Mains Cable with Plug USA Type NEMA 6-20P11R C
24B38615030Mains Cable with Plug EU 1-16P1R C
25A39311603Mains Line Filter 16A11
25B39311602Mains Line Filter 16A
2694090011Radial Fan 24V DC111R C
^2795000120
3071000003Air Intake Filter 200x 150x 12mm111R
3172291120Heat Sink Pad 215 x 98 x 5 mm111
3272261030Frame for Air Intake Filter111R
3372142470Air Deflector111R
98021743
5
672291131Protective Sheet (no longer required on power board, item 5)
794040050
Kit, Power Board, BH/BA 3500, 208VAC, 1N, 3.5kW. Kit includes a short
circuit plug and instructions to set board parameters. (was 98021721)
Kit, Power Board, BH/BA 3500, 240VAC, 1N, 3.5kW. Kit includes a short
circuit plug and instructions to set board parameters. (was 98021721)
Kit, Power Board, BH/BA 3500, 230VAC, 1N, 3.5kW. Kit includes a short
circuit plug and instructions to set board parameters. (was 98021703)
CU1/CU2 Sensors
NOTICE: When replacing the CU sensor only, ensure to initialize with
a short circuit plug (P/N 94900096, see Repair Accessories). Refer to
service manual for instructions.
Foot Complete Assembly, Adjustable
Service Tips: 208/240V North America market only. Retaining clips are
installed at factory on the feet to prevent threads from turning out
too far. It is necessary to open the unit to replace the feet.
NOTICE: After replacing
item, MUST RESET ALL
PARAMETERS with an IR
adapter tool (P/N 98990001,
see Repair Accessories).
Refer to service manual for
instructions.
198300101Upper Case SH/BA Assembly (Includes items 10, 11, 11A & 12)111
298300032Case Complete Top SH/BA Assembly (Includes items 1, 13, 14 &15)111
398200027Base Assembly (Includes items 22 - 28, 30 - 33)111
493003080Induction Coil #3.08 includes CU Sensors
+98021765
+98021740
+98021750
^
672291131Protective Sheet (no longer required on power board, item 5)
*
894040050
972115028Coil Carrier Sheet (Aluminum Plate) – Single, Counter-Top 111
1072140130Upper Case “SH/BA”111
1177322001Ceran Glass (or use item 1)111R C
11A70000002Silicone Gasket 306 x 6 x 4mm (for glass installation) 444R C
12A3012601Overlay (0-12). Use with Knob item 13A.111
12B66000002Overlay. Use with Knob item 13B.111
13A39400004Knob, Plain. Use with Overlay item 12A.111R
13B39400001Knob (0-12). Use with Overlay item 12B.111R
1494010011Power Switch - includes Potentiometer & Cable (4-pole) SH111R C
15A35624001LED 24V Green - Black Housing (NOT interchageable with item 15B)111R
15B35624009LED 24V Green - Chrome (NOT interchangeable with item 15A)111R
1660595006Screw M5 x 10mm (was 60595004 M5 x 12mm)444
1765840001Coil Pin M5 x 23mm444
1873000002Compression Spring 1.1 x 13 x 45.7444
1960595006Screw M5 x 10mm (was 60528501, Plastic Screw M5x8mm)444
2034120159Fuse SUT 15amp 250v 6.3x32222R C
2134110019Fuse T1.0A111R C
2239500003Screw Nut PG 16111
2339500009Screwed Cable Gland PG 16111
24A38614035Mains Cable with Plug USA Typ NEMA 6-20P11R C
24B38615030Mains Cable with Plug EU 1-16P1R C
25A39311602
25B39311603
2694090011Radial Fan 24V DC111R C
^2795000120
3071000003Air Intake Filter 200x 150x 12mm111R
3172291120Heat Sink Pad 215 x 98 x 5 mm111
3272261030Frame for Air Intake Filter111R
3372142470Air Deflector111R
^ Revised | + New | * Not Illustrated |
Part
Number
Description208V 230V240V
NOTICE MUST RESET ALL PARAMETERS with an IR adapter tool (P/N 98990001,
see Repair Accessories). Refer to service manual for instructions.
Kit, Power Board ET/ 1217, 240V, 1N, 3.5kW SH/BA. Kit includes a short circuit
plug and instructions to set board parameters. (was 98021721)
Kit, Power Board 208V, 1N,3.5KW SH/BA. Kit includes a short circuit plug and
instructions to set board parameters. (was 98021721)
Kit, Power Board 3.5kW, 230VAC, 1N, SH/BA. Kit includes a short circuit plug and
instructions to set board parameters. (was 98021703)
CU1/CU2 Sensors
NOTICE If replacing the CU sensor only, ensure to initialize with a short circuit
plug (P/N 94900096, see Repair Accessories). Refer to service manual for
instructions.
Mains Line Filter 16A
Note: 208V - Used UP TO serial# BA04.00103.1011
Note: 240V - Used UP TO serial# BA06.00098.0211
Mains Line Filter 16A
Mains Line Filter 16A
Note: 208V - Used FROM serial# BA04.00104.1011
Note: 240V - Used FROM serial# BA06.00099.1111
Foot Complete Assembly, Adjustable
Service Tips: 208/240V North America market only. Retaining clips are installed
at factory on the feet to prevent threads from turning out too far. It is necessary
to open the unit to replace the feet.
(1)
R=Recommended Stock Part / C=Critical Part
NOTICE Line Filters
25A and 25B are NOT
interchangeable. When
ordering a replacement
part, check both the
serial# and type of filter
installed on your unit.