Garelick 19874 User Manual

Installation Instructions for

Models 19853/19854/19873/19874
“Gull Wing Step” Boarding Ladders

Form 12.539

Rev. A

ASSEMBLY INSTRUCTIONS

1. Check parts against parts list.

2. Read instructions completely before starting assembly.

3. Note: Some hardware mounting is required. Therefore, a power

drill, drill bits, wrench or screwdriver is required, depending on
the type of mounting bolts and screws used.

4. Mounting bolts and screws are not supplied with ladder due to the
wide variety of mounting surfaces.

REQUIRED HARDWARE

NOTE: The following parts are not included due to the variety of

possible installations.

4 Suitable length 5/16"-18 stainless steel bolts

NOTE: Bolts should be at least 1-1/4" longer than transom
and backing plate thickness.

4 Suitable stainless steel backing washers
4 5/16"-18 stainless steel lock nuts

- Marine adhesive/sealant and anti-seize compound

- Backing plate (minimum size 4" x 5-1/2") of suitable material

MOUNTING INSTRUCTIONS – 99195 QUICK RELEASE

Refer to Fig. 1

1. Choose the most suitable side of transom for mounting ladder.

2. Locate a place on the transom where the ladder will mount and
not interfere with the turning and lowering operation of your
motor. Determine the actual waterline when the boat is at rest.
Mark this location in both the horizontal and vertical direction.

3. Locate the ladder on this mark and slide it up to the desired
mounting height. Keep in mind that it is optimal to have at least
two steps in the water for ease of boarding. Mark the ladder’s
position at the top of the swivel flange (Fig. 3). NOTE: This line

will locate the top two holes for the mounting plate.

4. Check the inside of the transom where the mounting is proposed.
Verify that there is ample space to install a backing plate
(minimum size 4" x 5-1/2") that will support the ladder
installation. A 4" x 5-1/2" minimum flat area or the size of your
backing plate is required for a secure installation. NOTE: The

backing plate should be made of either aluminum, marine
plywood or some other suitable non-compressive material.

Write for
a Complete

Catalog

Phone: [phone]
PO Box 8, 644 2nd Street E-mail: [e-mail]
St. Paul Park, Minnesota 55071 On the Web: www.garelick.com

1/05

Parts List

Model 19853/19854/19873/19874 Sport/Diver Ladders

Ref. Factory No.

Letter Part No. Req. Description

A 06.347 1 Mounting Substrate

B 08.280 1 Face Plate
C 03.653 1 Clevis Pin
D 03.654 1 Lanyard

Ladders position at top mounting bolt

Ladder centerline

Waterline

Ladder does not
interfere with turning

2 steps below
waterline

FIG. 1

5. Mark four mounting plate hole locations on your transom or
transom extension bracket using the plate as your template.

NOTE: This ladder has an adjustable feature that may
accommodate the desired angle; if not, it may be necessary to
make an external shim or modify the mounting substrate to
achieve the proper ascent angle (5 to 10 degrees) for your
ladder. Drill one 11/32" or 3/8" hole through your transom,
noting the angle of the mounting substrate hole angle. These
holes are perpendicular to the mounting face plate, not the
transom. When drilling, this hole angle should be used to insure
a proper installation. Place the mounting substrate and
faceplate against the boat and loosely mount it with the
hardware that you have selected for proper installation.

6. Level the bracket, mark and drill the next hole. Check the ladder
for level, make adjustments if necessary and then, drill the other
two holes.

7. Put a bead of adhesive caulk around the perimeter of the
mounting holes and all edges of the mounting substrate, coat the
bolt threads with anti-seize compound and secure the mounting
substrate in place by tightening all four mounting bolts.

(over)

Installation Instructions –
Models 19853/19854/19873/19874 “Gull Wing Step” Boarding Ladder

Form 12.539

Rev. A

OPERATING INSTRUCTIONS

Refer to Fig. 2 and Fig. 3

1. Both the 3- and 4-step ladders open in a similar fashion.

2. Rotate one of the steps counter-clockwise to open the ladder.

3. Rotate one of the steps clockwise to close the ladder.

4. To adjust the angle of the ladder with respect to the mounting
surface, remove nut and bolt “F” and adjust the angle for comfort
and ease of use.

99194 OPTIONAL STORAGE BRACKET MOUNTING INSTRUCTIONS

Refer to Fig. 4 (“E” – Storage Bracket, part #06.348, qty. 2)

1. Place mounting brackets “E” in desired location. Mark mounting
holes using the brackets as a template. Remove brackets.

2. Drill appropriate holes for fastener selected (not included).

3. Make sure fastener head is recessed in mounting block so as not
to interfere with the hanging of the ladder.

4. Secure ladder in position using clevis pin.

(NOTE: Do not remove clevis pin from lanyard.)

FIG. 3

FIG. 4

C

Swivel Flange Top

C

A

B

F

E

D

FIG. 2

NO JUMPING! NO DIVING!

SAFETY

INSTRUCTIONS

■ DO NOT USE WHEN MOTOR
IS RUNNING.

■ THIS LADDER DESIGNED
FOR BOAT USE ONLY.

■ FACE BOAT WHEN
ENTERING BOAT OR WATER.

■ ONLY ONE PERSON ON THE
LADDER AT A TIME.

■ CHECK ALL STEPS AND
HARDWARE BEFORE USING.

WARNING