Gardtec 593 User Manual

LCD & LED

User Instructions

PR5201.qxd 04/04/02 08:44 Page 1

Contents

User Information ......................................................... 2

Using LCD Keypads

Introduction ................................................................... 3

User Code Types.......................................................... 3

Setting The System ...................................................... 4

Unsetting The System .................................................. 5

Part Setting The System............................................... 5 - 6

Removing Zones........................................................... 7

Testing The System...................................................... 8

Viewing The Event Log................................................. 9 - 10

Changing The Chime Status......................................... 10 - 11

Programming User Codes ............................................ 12 - 14

Programming Time & Date ........................................... 15

User Initiating Remote Access ..................................... 16

Resetting After An Alarm .............................................. 17 - 18

Using LED Keypads.................................................... 19

Setting The System ...................................................... 19

Unsetting The System .................................................. 19

Part Setting The System............................................... 20

Removing Zones........................................................... 21

Testing The System...................................................... 22

Viewing The Event Log................................................. 23

Changing The Chime Status......................................... 24

Programming User Codes ............................................ 24 - 25

User Initiating Remote Access...................................... 25

Resetting After An Alarm .............................................. 26

LED Display Glossary................................................... 27 - 28

System Attributes.......................................................... 29

Service Record ............................................................. 30

User Chart .................................................................... 31

ACE Instructions ........................................................... 32

Programming ACE Keyfobs onto your System............. 33

Page 1

GARDTEC

593

User Manual

PR5201.qxd 04/04/02 08:44 Page 1

Page 2

GARDTEC

593

User Manual

User Information

Customer Name:-

Customer Address:-

Control Panel Model Gardtec 593

No of Keypads Keypad 1 Location Type Keypad 2 Location Type Keypad 3 Location Type Keypad 4 Location Type

ACE Mode (if fitted) Normal Security High Security Keyswitch Location Reserved User Code User No.

Installation Company Name:-

Installation Company Address:-

Installation Company Tel. Fax.

Other Information:-

Note: Please ensure this section is completed by the installation engineer

PR5201.qxd 04/04/02 08:44 Page 2

Page 3

GARDTEC

593

User Manual

Introduction

The Gardtec

593

control Panel is a microprocessor based unit with multiple user and engineer programmable options. Two types of display variation are also available, LCD giving two rows of 16 character English text and LED giving two 7 segment LED digits.Throughout this manual references will be made to the specific display

type. You may find this information from the user information section on page 2 of this manual.

Please take time to familiarise yourself with the type of equipment fitted to your premises as it will prove invaluable whilst using this manual.

User Code Types

Four types of User Codes are available on the Gardtec

593

each user code type allows for different levels of access. In total 7 User codes may be programmed by a Master Level User Code.

User number 1 will always be a Master Level User but the remaining 6 User Codes may be programmed (by a Master Code) to the required level of access. These may be changed at any time via a Master level code

The User Code levels available and the functions available for the levels are:-

1 = Set Only Only Allows for the setting of the system.

2 = Main User Allows Setting, Part Setting, Zone Remove (if programmed

by engineer), System Test, Unsetting, Reset after Alarm (if programmed by engineer).

3 = User Allows Setting, Part Setting, Reset after Alarm (if

programmed by engineer), Unsetting.

4 = Master Allows Setting, Unsetting, Zone Remove (if programmed by (User 1 always Master) engineer), Test System, View Log, Chime On/Off, User

Codes, Set Time/Date, Reset After Alarm (if programmed by engineer), Unsetting.

Note: For information on using Duress on the Gardtec

Series

see Using

Duress Section.

PR5201.qxd 04/04/02 08:44 Page 3

Page 4

GARDTEC

593

User Manual

Setting The System

1) With the display showing:-

2) Enter the User code (followed by YES if

Master or Main type code has been used). The display will show:and a continuous exit tone will sound

3) Exit the premises via the authorised exit

route (the exit tone will change if any detectors are violated during exit)

4) Once the premises are secure listen that the exit

tone returns to the continuous tone.

5) Wait until the exit tone finishes before leaving.

Setting & Unsetting the System via a Keyswitch

One of two types of keyswitch(es) may have been fitted to your system.

Normal

To set the system with a normal keyswitch, insert the key and turn to the ON position then remove the key. To unset insert the key and turn to the OFF position.

Biased

To set the system with a biased keyswitch, insert the key and turn it then return the key to the original position and remove. To unset repeat this operation.

< < < < UN-SET > > > >

01 JAN 18 : 58 : 01

EXIT Now ! All Zones ON 15

PR5201.qxd 04/04/02 08:44 Page 4

Page 5

GARDTEC

593

User Manual

Unsetting The System

1) Enter the premises via the authorised entry route

(the broken entry tone will sound), proceed to the keypad.

2) At the keypad enter a valid code, the display

will show:-

3) The system is now unset.

Part Setting The System (using Master & Main type codes)

1) With the display showing:-

2) Enter a Master or Main type code, the

display will show for example:-

3) Press 1, 2 or 3 (for Part 1, 2 or 3), the

display will show for example:-

< < < < UN-SET > > > >

01 JAN 18 : 58 : 01

< < < < UN-SET > > > >

01 JAN 18 : 58 : 01

Do you want to . . Set , STUART ?

EXIT Now! Part 1 15

PR5201.qxd 04/04/02 08:44 Page 5

GARDTEC

593

Page 6

User Manual

4) The exit tone may or may not be heard

dependant on the system settings.

5) Exit the premises or retire to an unprotected

part of the system. At the end of the exit time either the exit sounder will stop or a single beep will be emitted (dependant on system settings).

PR5201.qxd 04/04/02 08:44 Page 6

Page 7

User Manual

GARDTEC

593

Removing Zones When Setting (Master & Main codes onl

If programmed by the installation company individual zones may be removed, this may only be done by a Master or Main level of code.

1) With the display showing:-

2) Enter a Master or Main level code,

the display will show:-

3) Press NO, the display will show:-

4) Press YES, the display will show:-

5) Enter the zone number you wish to

remove followed by YES (pressing NO will 'un-remove' a zone), the display will show:-

6) Repeat step 5 until you have removed all

the required zones.

7) Press 0 to escape, the display will show:-

8) Press YES, the continuous exit tone will

sound.

9) Exit the premises via the authorised

exit route ( the exit tone will change as detectors are violated). When the premises are secure listen that the exit tone returns to the continuous tone. Wait until the exit tone finishes before leaving.

Note: Zone remove is only effective for the one set.

< < < < UN-SET > > > >

01 JAN 18 : 58 : 01

Do you want to . . Set . STUART ?

Do you want to . . REMOVE Zones ?

Enter Zone No. - then + YES or - NO

PR5201.qxd 04/04/02 08:44 Page 7

Page 8

User Manual

GARDTEC

593

Testing The System (Master & Main codes onl

1) With the display showing:-

2) Enter a Master or Main level code,

the display will show:-

3) Press NO, the display will show:-

4) Press NO, the display will show:-

5) Press YES to test the system

6) The display will show:-

7) Then for example:-

8) Pressing 1 will enter zone Status mode (All zones will show on the display

and will be deleted as each zone is triggered). Press 0 to escape. Pressing 6 will silence the internal sounder, Pressing 4 will toggle the Strobe On/Off, Pressing 9 will toggle the Bell On/Off

< < < < UN-SET > > > >

01 JAN 18 : 58 : 01

Do you want to . . Set . STUART ?

Do you want to . . REMOVE Zones ?

Do you want to . . TEST the System ?

1=Status 4 = Strobe 6 = Sounder 9 = Bell

< All Zones OK >

TESTING . . .

PR5201.qxd 04/04/02 08:44 Page 8

Page 9

User Manual

GARDTEC

593

9) Whilst in Test mode any zones violated

will sound the internal sounder (if it has not been silenced) and show on the display.

10) When you have finished testing the

system press 0 twice, the display will show:-

Viewing The Event Log (Master code onl

1) With the display showing:-

2) Enter a Master Code, the display

will show for example:-

3) Press NO three times, the display

will show:-

4) Press YES, the display will show:-

for 3 seconds

Then, for example:-

< < < < UN-SET > > > > 01 JAN 18 : 58 : 01

< < < < UN-SET > > > >

01 JAN 18 : 58 : 01

Do you want to . . Set . STUART ?

Do you want to . . View the LOG ?

While Viewing . . . 1 = Printer On / Off

Read Log

01 JAN 18 : 58 : 01

PR5201.qxd 04/04/02 08:44 Page 9

Page 10

User Manual

GARDTEC

593

5) This is the most recent event in the log.

Whilst viewing the Log,

Pressing NO will move back to the previous event.

Pressing YES will move forward to the next event.

Pressing 7 will take you to back to the last event of the previous day.

Pressing 9 will take you forward to the first event of the next day.

6) When you have finished viewing the Log press 0 twice

the display will show:-

Changing The Chime Status (Master code only)

The Chime zones will have previously been programmed by the installation company. A Master level code may change the status of the Chime between On and Off. To do so proceed as follows:-

1) With the display showing:-

2) Enter a Master Code, the display will

show for example:-

3) Press NO four times, the display will show:-

< < < < UN-SET > > > >

01 JAN 18 : 58 : 01

< < < < UN-SET > > > >

01 JAN 18 : 58 : 01

Do you want to . . Set . STUART ?

Do you want to . . Change Chime ?

PR5201.qxd 04/04/02 08:44 Page 10

+ 24 hidden pages

Gardtec 593 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual