Gardman Self Assembly Bird Table User Manual

Black

75% 50% 25%

Cyan

75% 50% 25%

Magenta

75 50 25

Yellow

75% 50% 25%

Paper

C+Y C C+M M M+Y YC+M+Y

Black

75% 50% 25%

Cyan

75% 50% 25%

Graphix Digital 01775 680718

artwork

g r a p h i x d i g i t a l

tudor gables thary lane surfleet spalding

lincolnshire pe11 4bn united kingdom

t: [phone]

e:

[e-mail]

www.graphixonline.co.uk

client:

date:

job no:

title:

size:

Gardman Ltd_AB

27.03.08

4948.2_A03072

SABT Instruction

A4 1pp

Cyan

Magenta

Yellow

Black

Cutter (do not print)

PMS

PMS

PMS

PMS

PMS

approval

method:

approved:

date:

Horizontal printer output check - this line measures 170mm

Vertical printer output check - this line measures 75mm

Self Assembly Bird Table
Instructions

Please read these instructions carefully before commencing assembly.

Tools required: crosshead screwdriver, tape/ruler.

Contents

16 x 25mm screws
25 x 40mm screws
6 x 60mm screws

Instructions

Site out of reach of predators.

Care

We recommend that you clean your feeders and bird tables with a mild disinfectant solution
once every two months or more often in warm weather. Remove as much old food and debris
as possible. Wash and thoroughly rinse all items*. Periodically reposition your feeders and
tables to a different area within the garden to avoid an accumulation of unhygienic deposits.

* Wash equipment outdoors, wear gloves and wash hands thoroughly afterwards.

1 Roof assembly

2 Roof

supports

Base section 1 Tray assembly 1 Centre

pole

(2 sections)

2 Table

support

blocks

4 Legs

Step 1

1 Attach end caps to ridge piece

using 2 x 40mm screws. Do
not fully tighten screws.

2 Attach rebated feather edge

under ridge piece edge with
2 x 25mm screws each end.

3 Attach standard feather edge

to end caps using 2 x 25mm
screws.

4Fully tighten ridge piece screws.

Roof Assembly

Rebated
feather
edge x 2

Ridge piece

End caps x 2

Feather
edge x 2

Step 2

1Position base

section centrally
onto bottom of
centre pole.

2 Screw together

using 1 x 60mm
screw.

Base Assembly

Step 3

1 Screw top of four

legs to the centre pole
using 4 x 40mm screws.

2 Screw the legs, at

their mid point, to
the base assembly
using 4 x 60mm
screws.

3 Assemble centre

pole as shown
using 3 x 40mm
screws.

Pole & Leg Assembly

Step 4

Tray & Leg Assembly

1Position table assembly

centrally on top of centre
pole and fix with 1 x 60mm
screw.

2 Screw the two table

support blocks to each
side of the centre pole.
Use 2 x 40mm screws per
support block.

3 Fix tray onto support blocks

using 2 x 40mm screws in
each piece.

Step 5

Roof Assembly

1 Attach the two roof supports

centrally onto the roof
assembly using 4 x 40mm
screws allowing roof
support to protrude
140mm below roof
assembly.

2Position complete roof

assembly onto the tray
assembly and fix with
4 x 40mm screws from
underneath.

140mm

A03072

For Customer Services Telephone:
[phone]

4948.2_A03072 Instruction#B752D 27/3/08 3:28 pm Page 1