
2ACA_3 Series
2W - Single Output AC-DC Converter - Universal Input - Isolated & Regulated
AC-DC Converter 2 Watt
Wide input voltage range:
85~305VAC/120~430VDC
AC and DC dual-use (input
from the same terminal)
Small size
Low ripple and noise
EMC meets EN55022,
EN55024
Low standby power
High efficiency up to 78%
Over output current protection
Short circuit protection (SCP)
Meet IEC61000, UL60950
and IEC60950 standards
3 years warranty
The 2ACA_3 series is the compact size power converters series offered
by Gaptec. It features compact size and 3000VAC safer isolation. It offers good EMC performance, meets IEC61000, UL60950 and IEC60950
standards, and is widely used in industrial, electricity, instruments and
civil applications.
If it is planned to be used in electricity and other higher requirement to
EMC applications, one must connect a typical application.
(pending)
Approval Model Package Power
UL/CE 2ACA_03S3 33.7x22.2x18mm 2 3.3V 600mA 100 65 4000
UL/CE 2ACA_05S3 33.7x22.2x18mm 2 5V 400mA 100 70 4000
UL/CE 2ACA_09S3 33.7x22.2x18mm 2 9V 222mA 100 72 2200
UL/CE 2ACA_12S3 33.7x22.2x18mm 2 12V 167mA 100 76 2200
UL/CE 2ACA_15S3 33.7x22.2x18mm 2 15V 133mA 100 76 1000
UL/CE 2ACA_24S3 33.7x22.2x18mm 2 24V 83mA 100 78 680
Input specifications
Input voltage range 85~305VAC, 120~430VDC
Input frequency 47~63Hz
Input current 110VAC
Inrush current 110VAC
Leakage current 0.15mA (max)
Recommended eExternal
input fuse (special package
series include fuse)
Hot plug Unavailable
Note:
1. Models listed with strike-through text have been officially discontinued.
2. Unless otherwise specified, all specifications are measured at rated input voltage
and rated output load, TA=25°C, humidity < 75%.
3. All specifications stated in this datasheet are subject to the above listed models
only. For specifications of non-standard models, please contact our technical
support team.
• 37mA (max)
• 7A (typ)
1A/300V
[W]
Output
[Vo]
230VAC
• 21mA (max)
230VAC
• 14A (typ)
Output
[lo]
Output specifications
Output voltage accuracy ±5% (max)
Line regulation (full load) ±2% (typ)
Load regulation (10% to 100%) ±5% (typ)
Ripple & Noise* (p-p) 20MHz Bandwidth:
Temperature coefficient ±0.04%/°C (typ)
Stand-by power consumption 0.2W (max)
Short circuit protection Continuous, and auto resume
Over current protection 110%~400% IO can auto resume
Hold-up time 230VAC output:
* Ripple and Noise are measured by the method of parallel lines, please see AC-DC
Converter Application Notes for specific operation methods.
Model selection:
WTC_yyN##
W= Watt; T= Type; C= Case; yy= Vout; N= Numbers of Output;
##= Isolation (kVAC)
Example:
2ACA_05S3
2= 2Watt; AC= AC-DC; A= case style; 5Vout; S= Single Output;
3= 3kVAC
Ripple and Noise
[mV, typ]
Efficiency
[%, typ]
±6% (max) at 3.3V output
100mV (typ), 200mV (max)
50ms (typ)
Capacitive load
[µF, max]
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
2ACA_3 – Rev. 2017-1.3
Page 1 of 4
Specifications subject to change without notice.

2ACA_3 Series
2W - Single Output AC-DC Converter - Universal Input - Isolated & Regulated
Common specifications
Operating temperature range -25°C ~ +70°C
Storage temperature range -25°C ~ +85°C
Power derating temperature range -25°C ~ -10°C; 1.33%/°C
Cooling Free convection
Storage Humidity 95% RH (max)
Switching frequency 100kHz (max)
I/O-isolation voltage 3000VAC/1Min
EMC / EMI / CE CISPR22/EN55022, CLASS B
EMC / EMI / RE CISPR22/EN55022, CLASS B
EMC / EMS / ESD IEC/EN61000-4-2 ±4KV / ±8KV perf. Criteria B
EMC / EMS / RS IEC/EN61000-4-3 10V/m perf. Criteria A
EMC / EMS / EFT* IEC/EN61000-4-4 ±2KV perf. Criteria B
EMC / EMS / Surge Immunity IEC/EN61000-4-5 ±1KV/±2KV perf. Criteria B
EMC / EMS / CS IEC/EN61000-4-6 10 Vr.m.s perf. Criteria A
EMC / EMS / PFM IEC/EN61000-4-8 10A/m perf. Criteria A
EMC / EMS / Voltage dips, short and
interruptions immunity
Safety certification EN60950,UL60950
Safety class CLASS II
Case material UL94V-0
Install PCB
MTBF MIL-HDBK-217F@25°C >300,000h @25°C
Weight 20g
55°C ~ 70°C; 3.3%/°C
(see EMC solution-recommended circuit)
(see EMC solution-recommended circuit)
IEC/EN61000-4-11 0%-70% perf. Criteria B
Typical characteristics
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
2ACA_3 – Rev. 2017-1.3
Page 2 of 4
Specifications subject to change without notice.

2ACA_3 Series
2W - Single Output AC-DC Converter - Universal Input - Isolated & Regulated
Typical efficiency curve
2ACA_024S3
2ACA_12S3
2ACA_05S3
2ACA_024S3
2ACA_12S3
2ACA_05S3
Typical application circuit
Model C1(µF) C2 (µF) TVS
2ACA_03S3
2ACA_05S3
2ACA_09S3
2ACA_12S3
2ACA_15S3
2ACA_24S3
Note:
Output filtering capacitor C2 is electrolytic capacitor, it is recommended to use high frequency
and low impedance electrolytic capacitor. For capacitance and current of capacitor please refer
to manufacture’s datasheet. Capacitor withstand voltage derating should be 80% or above.
C1 is ceramic capacitor, which is used to filter high-frequency noise. TVS is a recommended
component to protect post-circuits if converter fails. External input FUSE is recommended
to use 1A/300V; external input MOV is recommended to use S14K350; external input NTC
is recommended to use 10D-11; external input CX is recommended to use 0.47μF/305VAC.
1 220 SMBJ7.0A
1 220 SMBJ7.0A
1 120 SMBJ12A
1 120 SMBJ20A
1 120 SMBJ20A
1 68 SMBJ30A
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
2ACA_3 – Rev. 2017-1.3
Page 3 of 4
Specifications subject to change without notice.

2ACA_3 Series
2W - Single Output AC-DC Converter - Universal Input - Isolated & Regulated
EMC solution-recommended circuit
Components Recommended parameter
MOV S14K350
CY3 2.2nF/400V
CY4 2.2nF/400V
CX 0.47μF/305VAC
LCM 10 mH
R1 47Ω/3w
FUSE 1A/300V, slow blow, it must be connected to FUSE
Mechanical dimensions
Note:
Unit: mm[inch]
Pin diameter tolerances: ± 0.10mm[± 0.004inch]
General tolerances: ± 0.50mm[± 0.020inch]
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
2ACA_3 – Rev. 2017-1.3
Page 4 of 4
Specifications subject to change without notice.