Ganz ZN-D1MTP-IR, ZN-D1MAP User Manual

1

2

SAFETY INSTRUCTIONS

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with a dry cloth.

7) Do not block any of the ventilation openings. Install in accordance with the manufacturer's
instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
that produce heat.

9) Only use the attachments/accessories specified by the manufacturer.

10) Use only with a cart, stand, tripod or bracket specified by the manufacturer, or sold with the

apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid
injury from tip-over.

12) Unplug this apparatus during lightning storms or when unused for long periods of time.

13) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has be

en damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled o
r objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, doe
s not operate normally, or has been dropped.

Caution
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.

These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric
shock does not perform any servicing other than that contained in the operating instructions unless you
are qualified to do so.

In USA and Canada, Use Class 2 Power Supply Only

3

Contents

1. Product Features .................................................................................................................................... 5

2. Accessing the Camera............................................................................................................................ 9

2.1 Access from a browser.................................................................................... 9

2.2 Accessing the camera from the Internet ........................................................... 10

2.3 Adjusting the Image and Focus ...................................................................... 10

2.4 The Live View page ....................................................................................... 10

2.5 Video stream types ....................................................................................... 11

2.6 How to stream H.264 .................................................................................... 11

3. The Setup .............................................................................................................................................. 12

4. Analog output ....................................................................................................................................... 13

4.1 Analog Output Setup .................................................................................... 13

5. Video ...................................................................................................................................................... 13

5.1 Codec ......................................................................................................... 13

5.2 Camera ....................................................................................................... 16

5.2.1 Exposure Control .................................................................................... 16

5.2.2 Day & Night Control ................................................................................ 17

5.2.3 White Balance Control ............................................................................. 17

5.2.4 Image Property Control ............................................................................ 17

5.2.5 Lens Adjustment .................................................................................... 17

6. Audio ...................................................................................................................................................... 18

7. Live ......................................................................................................................................................... 19

7.1 Setup ........................................................................................................ 19

7.2 Privacy Masking ......................................................................................... 20

8. FTP ......................................................................................................................................................... 21

8.1 FTP > Config ............................................................................................... 21

8.2 FTP > Event ................................................................................................. 21

8.3 FTP > Periodical ........................................................................................... 22

9. Event ...................................................................................................................................................... 23

9.1 Event > Alarm Port ........................................................................................ 23

9.2 Event > Motion ............................................................................................. 24

9.3 Event > Mapping .......................................................................................... 25

10. Network ................................................................................................................................................ 26

10.1 Network > IP Setup ..................................................................................... 26

10.2 Network > Service Port ................................................................................ 28

10.3 Network > RTP ........................................................................................... 28

10.4 Network > E-mail ........................................................................................ 29

10.5 Network > DDNS ......................................................................................... 29

10.5 Network > UPnP ......................................................................................... 30

11. System ................................................................................................................................................. 31

11.1 System > User ............................................................................................ 31

11.2 System > Date & Time ................................................................................. 32

11.3 System > Maintenance ................................................................................ 33

11.4 System > Information .................................................................................. 35

12. Dimension (mm) .................................................................................................................................. 36

4

13. Specification ....................................................................................................................................... 37

5

1. Product Features

The GANZ PixelPro is a high performance H.264 network camera, designed for
demanding security installations. It delivers crisp, clear images, disclosing every
detail, thanks to its top quality Megapixel progressive CMOS sensor and advanced
image processing.

Supported by the industry’s largest base of video management software, the GANZ
PixelPro provides the perfect solution for securing bank offices, airports and other
facilities, and for traffic surveillance, over IP based networks.

The optimal Power over Ethernet (IEEE 802.3af) support power to the camera to be
delivered via the network, eliminating the need for a power outlet and reducing
installation costs. Steady power could be guaranteed with a central Uninterruptible
Power Supply (UPS).

The GANZ PixelPro offers a comprehensive set of network security and
management features.
This includes support for port based network control (IEEE802.1X), which allows the
camera to be connected to a network secured with this control, and HTTPS
encryption, which provides a secure channel between camera and application. It also
enables authentication of the video source. Video products are efficiently managed
with the powerful Management tool, which is provided on the Installation CD which
comes with camera.

6

1. Network connector (RJ-45 PoE supported)

The GANZ PixelPro connects to the network via a standard network cable, and
automatically detects the speed of the local network segment (10BaseT/100BaseTX
Ethernet). This socket could also be used to power the GANZ PixelPro via Power
over Ethernet (PoE). The camera auto-senses the correct power level when using a
PoE switch, router or injector.

2. Power connector

12 VDC or 24VAC power connector

3. I/O Signal terminal block

Audio in

Audio in (line level), for line-in mono signal (only left channel is used from a stereo
signal)

7

Audio out

LED Color

Indication

System Status

Green

On

Connection to 10/100Mbps Network / LAN.

Network connection is established.

Flashes

Indication of network activity.

Camera is booting up.

Unlit

-

No network connection established.

When no or incorrect power is supplied.

Amber

On

Camera reset is in progress.

Flashes

Factory Default settings are in progress.

The Audio output (line level), which could be connected to a line output of a
microphone system or an active speaker with a built-in amplifier.

Alarm in

One analog (dry contact) alarm input

Alarm out

One relay output (0.5A 125VAC / 1A 30VDC)

4. Control Button

This button has 3 functions by pressing time.

1) Switch NTSC / PAL format (less than 1 second)

2) System reboot (around 5 seconds)

3) Factory Default Reset (More than 10 seconds)

5. Video output for service monitor

This analog video output is available. Use accessory cable to video output.

6. Status LED

8

Installation Preparation

1) Turn the bottom cover clockwise and separate the unit and the cover.

2) Separate the top cover and the camera unit.

3) Make holes for cables to ceiling / wall with supplied template.

1 2 3

Mounting to a ceiling / wall

4) Secure the bottom cover to a ceiling / wall with two supplied tapping screws (4x30) and anchors.

5) Attach the unit to the bottom cover and turn it counter clockwise. Then secure the unit with two

supplied tapping screws (3x8).

6) Attach the top cover to the unit.

4 5 6

9

2. Accessing the Camera

Follow the instructions in the GANZ PixelPro Installation Guide to install the camera.
The GANZ PixelPro could be accessed with most standard operating systems and

browsers. The recommended browser is Internet Explorer for Windows with other
operating systems.

2.1 Access from a browser

1. Start a browser (Internet Explorer)

2. Enter the IP address or host name of the camera in the Location/Address field of

your browser. Press Enter.

3. Login dialog will appear when the camera is accessed for the first time.

4. The default user name is ADMIN, and password is 1234.

5. The camera’s Live View page is now displayed in your browser.

Note: The layout of the live view page in the camera may have been customized to

meet specific requirements. Consequently, some of the examples and
functions featured here may differ from those displayed on your own Live View
page.

10

2.2 Accessing the camera from the Internet

Once installed, the camera is accessible on the local network (LAN). Configure the
router/firewall to allow incoming data traffic to access the camera from the Internet.
For security reasons this is usually done on a specific port. Please refer to the
documentation for router/firewall for further instructions.

2.3 Adjusting the Image and Focus

To adjust the position of the lens:

1. Open the Live View page in your web browser.

- Select the Setup tab, and open the Analog output page.

- Select the ‘Video Format'.

2. Connect analog monitor to the VIDEO OUT (BNC) on the supplied cable.

- Control the ZOOM/FOCUS by the Lens Adjustment window, and adjust the

camera angle.

For lens adjustment method, please refer to “5.2.5 Lens Adjustment”.

3. Check the image from the Live View page on your web browser.

4. You can refocus adjustment by Lens Adjustment window, if you want fine lens

adjustment.

2.4 The Live View page

Enable/Disable PC Speaker output
Enable/Disable PC Microphone input

Digital Zoom

Snap Shot

Full Screen
Video Stream change: First stream  Second stream
Play: Click this button by manually to start the stream

Stop: Click this button by manually to stop streaming

NOTE: It is possible that not all the buttons described below will be visible unless the
Live View page has been customized to display them.

11

2.5 Video stream types

H.264 protocols and communication methods

• RTP (Real-time Transport Protocol) is a protocol that allows programs to manage

the real-time transmission of multimedia data, via unicast or multicast.

• RTSP (Real Time Streaming Protocol) serves as a control protocol, to negotiate the

type of transport protocol to use for the stream. RTSP is used by a viewing client to
start a unicast session.

• UDP (User Datagram Protocol) is a communications protocol that offers limited

service for exchanging data in a network which uses the Internet Protocol (IP).
UDP is an alternative to the Transmission Control Protocol (TCP). The advantage of
UDP is that, it is not required to deliver all data and may drop network packets when
there is network congestion. This is suitable for live video, as there is no point in re­transmitting old information that will not be displayed anyway.

• Unicasting is communication between a single sender and a single receiver over a

network. This means that the video stream goes independently to each user, and
each user gets own stream. A benefit of unicasting is, in case one stream fails, it
only affects one user.

• Multicasting(Will be supported)is bandwidth-conserving technology that reduces

bandwidth usage by simultaneously delivering a single stream of information to
multiple network recipients. This technology is used primarily on delimited networks
(intranets), as each user needs an uninterrupted data flow and should not rely on
network routers.

2.6 How to stream H.264

Deciding on the combination of protocols and methods to use depends on your
viewing requirements, and on the properties of your network. Setting the preferred
method(s) is done in webpage.

RTP+RTSP

This method (actually RTP over UDP and RTSP over TCP) should be your first
consideration for live video, especially when it is important to always have an up-to­date video stream, even if some images are lost due to network problems. This could
be configured as multicast or unicast.

RTP/RTSP/Multicasting (Will be supported) provides the most efficient usage of
bandwidth, especially when there are large numbers of clients viewing
simultaneously. Note however, that a multicast broadcast could not pass a network
router unless the router is configured to allow this. For example, It is impossible to
multicast over the Internet.

12

RTP/RTSP/Unicasting should be used for video-on-demand broadcasting, so that
there is no video traffic on the network until a client connects and requests the
stream. However, as more and more unicast clients get connected, the traffic on the
network will increase and may cause congestion. Although there is a maximum of 10
unicast viewers, note that all multicast users combined count as 1 unicast viewer.

RTP/RTSP

This unicast method is RTP tunneled over RTSP. This could be used to exploit the
fact that it is relatively simple to configure firewalls to allow RTSP traffic.

3. The Setup

The GANZ PixelPro is configured from the Setup link, which is available on the top
left hand side in the web interface. This configuration could be done by:

• Administrators, who have unrestricted access to all settings under the Setup tab.

Accessing the Setup link from a browser

1. Start your web browser and enter the IP address or host name of the camera into

the address bar.

2. The Live View page is now displayed. Click on the Setup tap.

13

4. Analog output

4.1 Analog Output Setup

Analog output allows selection of output format of the analog BNC output from
the camera. NTSC, PAL: Analog Output is selectable.

5. Video

The following descriptions show examples of some of the features available in the
GANZ PixelPro.

5.1 Codec

These are the tools for adjusting the H.264 settings and controlling the video bit rate.