Ganz PT118XT-HD Installation Instructions

P

T

1

8

X

T

T--

H

D

Outdoor Vandal Proof 18X IP HD PTZ Dome

UUser Manual

NY: 55 Mall Drive • Commack, NY 11725 (800) 422-6707

&$6:HVWHUQ$YH • Torrance, CA 9050 (877) 407-9555

www.computarganz.com

Megapixel Speed Dome Camera Instruction Manual

This symbol (lightning flash with arrowhead) is intended to alert the user to the presence of un-insulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

This symbol (exclamation point) is intended to alert the user about the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT OPEN THE COVERS.

THERE ARE NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONAL

Megapixel Speed Dome Camera Instruction Manual

Important Safety Guide

Caution

NOTICE

1. Read, heed and follow all the Instructions

Read all the safety and operating instructions before using the product.

2. Keep this manual

Keep this manual for future reference.

3. Attachments / Accessories

Use only the attachments or accessories specified by the manufacturer.

4. Installation

Do not install near any heat resources such as radiators, heat registers, stoves, or other apparatus including

amplifiers that product heat. Improperly installed product may fall, cause serious injury to a child or adult

and damage the product. Do not block any ventilation holes or openings. Install in accordance with the

manufacturer‟s instructions. Use only with the cart, stand, tripod, bracket, mounting devices, or table

specified by the manufacturer. Installation should be done only by qualified personnel and conform to all

the instructions by the manufacturer. Refer all servicing to qualified service personnel.

5. Power source

This product should be operated with the same type power source as indicated on the marking label

1. Operating

1. Before using, make sure that the power supply and associated parts are properly installed.

2. While operating, if any abnormal condition or malfunction is observed, stop using the product immediately and

then contact your local dealer.

2. Handling

1. Do not disassemble or tamper with the parts inside the product.

2. Do not drop or subject the product to shock and vibration as this can damage the product.

3. Care must be taken when you clean the clear dome cover. Especially, scratches or dust on the cover

will ruin the quality of the product.

3. Installation and Storage

1. Do not install the product in areas of extreme temperature, which exceed the allowable range.

2. Avoid installing in high humid or dusty environments.

3. Avoid installing in places where radiation is present.

4. Avoid installing in places where there are strong magnetic fields and electric signals.

5. Avoid installing in places where the product would be subject to strong vibrations.

Megapixel Speed Dome Camera Instruction Manual

① Introduction

Features

6

Package Components

8

Main Part Description

9

DIP Switch Setup

10

② Installation

Installation using Wall Mount Bracket

13

Wiring and Cabling

14

③ Configuration

Web-View Main Screen

18

Video & Audio Configuration

Codec

____

19

Video

20

Audio

21

Privacy zone

22

PTZ Configuration

1. Basic configuration

23

2. RS 485 configuration

23

3. Preset & Preset Sequence

24

4. Swing

25

5.Pattern

26

6.Group Tour

27

CONTENTS

Megapixel Speed Dome Camera Instruction Manual

Event Configuration

1. Sensor and Relay

28

2. Emergency Alarm

29

Network Configuration

1.IP Setup

30

2.Dynamic DNS

30

3. Live Protocol

31

4. IP Filtering

31

System Configuration

1.Upgrade

32

2.Time & Date

32

3. Event Mail

33

4. User Management

34

④ Specifications

Specifications

35

Dimension

37

CONTENTS

Megapixel Speed Dome Camera Instruction Manual

Feature

INTRODUCTION

1

This „IP-server‟ supports remote images, sound, setup and control of camera functions though IP Networks such as LAN, ADSL/VDSL, and Wireless LAN

 Camera Specifications

 Image Sensor :  Zoom :  WDR function (Wide Dynamic Range)  SNR(Super Noise Reduction) function

 You can adjust focus to PTZ camera with 'Semi-Auto Focus function' included Auto-Focus, Manual Focus.

 Video

 Supports H.264, MPEG4,MJPEG (H.264 is the latest high efficiency compression format)  Various Resolutions : 1280720 ~ 256144  Supports a wide range of bandwidth control : 50kbps ~ 8Mbps  Supports HD-SDI(HDCCTV) video output

 Audio

 Supports various transmission modes :

Simplex (IP-server → Client PC / Decoder, Client PC / Decoder → IP server) and full-duplex

 Network

1/3" Megapixel solid State Progressive Scan CCD.

 18 Optical Zoom

 Supports static IP, dynamic IP (DHCP), and PPPoE  Supports 1:1 and 1:N connection  Supports Multicast transmission

 Supports various network protocol: TCP/IP, UDP, Multicast, DHCP, SMTP, HTTP, SNMP, RTP, RTSP

 Powerful Pan/Tilt function

 MAX. 360/sec High Speed Pan/Tilt movement.  With the Vector Drive Technology, Pan/Tilt motions are accomplished along the shortest path. As a

result, the time to view a target is remarkably short and the video output displayed feels very natural

for monitoring.

 With the Micro-Stepping Control Technology, video movements still look very smooth at high zoom

magnification. During operation via a controller the camera can be moved by as little as 0.05/sec.

Hence it is very easy to make the camera focus on desired target even at high zoom magnification.

Additionally it is easy to make the camera focus on desired positions with zoom-proportional pan/tilt

movement.

Megapixel Speed Dome Camera Instruction Manual

INTRODUCTION

1

 Preset, Swing, Group

 You can set up to 99 preset positions, and assign camera image setting to each preset. Additional it is

possible to also assign a label/name to each preset position.

 A maximum of 8 Swing sets are programmable. This function allows the user to set the camera to

move repetitively between two preset positions at a programmed speed.

 A maximum of 4 Patterns are programmable. This function allows the user to set the camera to

memorize a path (mostly curve path) by the joystick of the controller and record the trajectory

operated by the joystick as closely as possible.

 A maximum of 8 Group sets are programmable. This function is that the camera memorizes the

combination of Presets, Pattern and/or Swings sequentially and runs these Presets, Pattern and/or

Swings repetitively. A Group can be any combination of up to 20 Preset/Pattern/Swing functions.

 PTZ control

 Using RS-485 communication connection, a maximum of 255 cameras can be connected to a single

controller.

 Alarm in/ output (Supported only on appropriate models)

 3 alarm sensor inputs and 1 alarm relay output are available.  The alarm sensor inputs are decoupled with photo-couplers to avoid external electric noise and

shock protection.

 Both N.O.(Normal Open) sensors and N.C.(Normal Close) sensors can be used and the signal range

of the Alarm output can be from DC 5.0V to 12.0V depending on the various applications.

 The camera can be set to move to a Preset position or to run functions such as Pattern, Swing and

Group when there are external sensor activations. Also “Post Alarm” function is possible, which is

supposed to activate after a user-defined time period and sequentially in succession to the action by

external sensor activations

 Designed for various

 The fans and heaters are built-in to the camera for cold and hot temperature environments. Also

idealistic case design protects the camera from wet and dusty environments. (IP67)

 The camera is designed for easy to installation and maintenance.

Outdoor Environments and Easy Installation

Megapixel Speed Dome Camera Instruction Manual

Package Component

 Main Body & Clear Dome Cover

 Default Accessories

[Main Cable, Wrench]

 Audio Cable

 BNC (2ea)

 LAN Crossover Cable

 CD  Manual

 Wall Mount Bracket

[Screws : Machine M515, Hex Lag #1450]

INTRODUCTION

1

 Product & Accessories

 Brackets

Megapixel Speed Dome Camera Instruction Manual

Main Part Description

 Dome Cover

Do not remove the protection vinyl from the dome cover before finishing

all the installation processes. This is to protect the dome cover from

scratches or dust.

 DIP Switch  Drop Prevention Spring

Used to set up the camera IDs and protocols.

Used to protect the product from being dropped by connecting safety

wire of bracket to hook of main body when being installed.

 Mount Screw Hole

Used to assemble the main body with a bracket using screws.

 Main Connector

Used for the power wire, the video cable and the RS-485 communication

cable connection.

 LAN Connector  Audio Port  Video (BNC)  IP Module Reset Switch

Used for Ethernet cable connection. (Only supported on IP models)

Used for Audio In/Out connection

Used for HD-SDI cable connection.

Used for system rebooting

INTRODUCTION

1

Megapixel Speed Dome Camera Instruction Manual

DIP Switch Setup

Before installing the camera, set up the DIP switches to configure the camera ID and the communication protocol.

ON

1 2 3 4 5 6 7 8

Pin 1 2 3 4 5 6 7 8

ID 1 2 4 8

16

32

64

128

ID 1 2 4 8

16

32

64

128

1

on

off

off 11

on

off

on

off

off 2 off

on

off

off 12

off

on

off

off 3 on

on

off

off 13

on

off

on

off

off 4 off

off

on

off

off 14

off

on

off

off 5 on

off

on

off

off 15

on

off

Off 6 off

on

off

off 16

off

on

off

7

on

off

off 17

on

off

on

off

off 8 off

off

on

off

off 18

off

on

off

on

off

off 9 on

off

on

off

off 19

on

off

Off

on

off

10

off

on

off

on

off

off 20

off

on

off

on

off

 The ID number of camera is set using a binary number. Examples

shown below.

 The range of ID is 1~255. UDo not use 0 as camera IDU. Factory

default of Camera ID is 1.

 If you want to control a certain camera, you must match the camera ID

with Cam ID setting of DVR or Controller.

INTRODUCTION

1

 Camera ID Setup

Megapixel Speed Dome Camera Instruction Manual

1 2 3 4

ON

Pin 1 2 3 4 5 6 7 8

ID 1 2 4 8

16

32

64

128 ID 1 2 4 8

16

32

64

128

21

on

off

on

off

on

off

off 31

on

off

22

off

on

off

on

off

off 32

off

on

off

23

on

off

on

off

off 33

on

off

on

off

24

off

on

off

off 34

off

on

off

on

off

25

on

off

on

off

off 35

on

off

on

off

Off

26

off

on

off

on

off

off 36

off

on

off

Off

on

off

27

on

off

on

off

off 37

on

off

on

off

Off

on

off

28

off

on

off

off 38

off

on

off

Off

on

off

29

on

off

on

off

off 39

on

off

Off

on

off

30

off

on

off

off 40

off

on

Off

on

off

 Select an appropriate Protocol using the below DIP switch combinations.

Switch Mode

Protocol

P0

(Pin 1)

P1

(Pin 2)

P2

(Pin 3)

OFF

PELCO-D, 2400 bps

ON

OFF

PELCO-D, 9600 bps

OFF

ON

OFF

PELCO-P, 4800 bps

ON

OFF

PELCO-P, 9600 bps

Others

Reserved

 Match the camera protocol with the camera protocol setting of your DVR

or controller to control the camera.

 Adjust the DIP switch after turning off the camera. If you changed the

camera protocol by changing the DIP S/W, the change will be effective after you reboot the camera.

 The factory default protocol is “Pelco-D, 2400 bps”

INTRODUCTION

1

 Communication Protocol Setup

Megapixel Speed Dome Camera Instruction Manual

1 2 3 4

ON

The terminal resistor is used for the following cases.

 In case that the control cable length between a camera and a

controller is relatively very long (1:1 Connection)

If the communication cable length is very long, the electrical signal

will bound in the terminal point. This reflected signal causes

distortion of original signal. Accordingly, the camera can then be out

of control. In this case, the terminal resistor of both sides i.e. the

camera and the controller must be set to „ON‟ state.

 In case that multiple cameras are connected to a controller

Due to similar reasons with the case 1, the terminal resister of the

controller and the last camera must be set to „ON‟ state. The last

camera means the camera farthest in cable length from the

controller. Do not turn on the terminal resistor of more than one

camera on the same communication cable.

INTRODUCTION

1

 Terminal Resistor Setup

Ganz PT118XT-HD Installation Instructions

Specifications and Main Features

Frequently Asked Questions

User Manual