Page 1
P
T
1
1
2
P
T
1
1
Vandal Resistant 12x PTZ Dome
2
N//
N
P
P
T
T
1
1
1
1
2
2
N--
N
X
X
T
T
UUser Manual
NY: 55 Mall Drive • Commack, NY 11725 (800) 422-6707
CA: 21241 S. Western Ave, Suite 160 • Torrance, CA 90503
(877) 407-9555
www.computarganz.com
Page 2
CONTENTS
1E
A○
Introduction
A
Feature s
Product & Accessories
Parts Name & Functions
2E
A
A○
Installation
DIP Switch Setup 8
Installation using Ceiling Mount Bracket
Installation using Wall Mount Bracket
Installation using Flush Mount Bracket
Cabling 14
3E
A○
Operation
A
Check Points before Operation
Preset and Pattern Function Pre-Check
Starting OSD Menu
Reserved Preset
Preset
Swing
Pattern
Group
Other Functions
OSD Display of Main Screen
4E
A○
How to use OSD Menu
A
General Rules of Key Operation for Menu
Main Menu
Display Setup
Privacy Zone Mask Setup
Camera Setup
Motion Setup
Preset Setup
Swing Setup
Pattern Setup
Group Setup
System Initialize
5E
A○
Specifications
A
3
5
7
11
12
13
17
17
18
18
19
19
20
21
22
23
24
24
25
26
27
30
32
33
34
35
37
38
Dimensions
39
Page 3
Camera Specifications
Advanced Pan/Tilt Functions
Fe at u re s
z CCD Sensor : 1/4" Super-HAD CCD
z Zoom Magnification : × 12 Optical Zoom, × 12 Digital Zoom (Max × 144 Zoom)
z Day & Night Function
z Variable Focus Mode: Auto-Focus / Manual Focus / Semi-Auto Focus.
z Independent & Simultaneous Camera Characteristic Setup in Preset operation
z Max. 360°/sec high speed Pan/Tilt Motion
z Using Vector Drive Technology, Pan/Tilt motions are accomplished with the shortest path. As a result,
time to target view is reduced dramatically and the video stream transfers are natural to watch.
z For jog operation using a controller, an ultra slow speed of 0.05°/sec can be reached, making it very
easy to relocate camera to the desired target view. Additionally, it is easy to move the camera to a
desired position with zoom-proportional pan/tilt movement.
INTRODUCTION
INTRODUCTION
1
1
.
Preset, Pattern, Swing, Group, Privacy Mask and More…
z Max. 127 Presets are assignable and characteristics of each preset can be set up independently, such as
White Balance, Auto Exposure, Label and so on.
z Max. 8 set of Swing actions can be stored. This enables camera to move automatically between two
preset positions at a designated speed.
z Max. 4 Patterns can be recorded and played back. This enables camera to automatically follow any
trajectory preset by joystick as closely as possible.
z Max. 8 set of Group action can be stored. This enables camera to move automatically with a
combination of Preset or Pattern or Swing. A Group is composed of max. 20 entities of Preset/
Pattern/Swings.
z Privacy Masks are assignable, so as not to intrude on other’s privacy. (8 Privacy Zones)
PTZ (Pan/Tilt/Zoom) Control
z With RS-485 communication, max. of 255 cameras can be controlled at the same time.
z Pelco-D or Pelco-P protocol can be selected as a control protocol in the current firmware version.
Speed Dome Camera Instruction Manual
3
Page 4
OSD (On Screen Display) Menu
z OSD menu is provided to display the status of camera and to configure the functions interactively.
z The information such as Camera ID, Pan/Tilt Angle, Alarm Input and Preset can be displayed on screen.
Alarm I/O Functions
z 4 alarm sensor Inputs are available.
z To completely eliminate external electric noise and shock, alarm sensor Input is decoupled from photo
coupler.
z If an external sensor is activated, camera can be set to move to the corresponding Preset position.
Reserved Presets for Special Purpose
z Most camera characteristics can be set up easily and directly with reserved preset, without entering the
OSD menu. For more information, refer to “Reserved Preset” in this manual.
INTRODUCTION
1
IP66 (weather resistant) *(PT112N-XT model only).
z This product has been certified to the IP66 standard for waterproof and spray proof environments. Also
for the same reason it can be protected from dust and rainstorms.
Speed Dome Camera Instruction Manual
4
Page 5
Product & Accessories
Product & Accessories- UPT112N-XT model (outdoor)U.
z Main Body z Mount Adapter z Gasket(Rubber)
INTRODUCTION
1
z Terminal Block z Screws z Six angles wrench
Video cable
Options
z Wall Mount Bracket z Ceiling Mount Bracket z Sun shield
Speed Dome Camera Instruction Manual
5
Page 6
Product & Accessories-U PT112N model (indoor)U.
z Main Body z Surface Mount Bracket z Screws & Terminal Block
Options
INTRODUCTION
1
z In-Ceiling Mount Bracket z Ceiling Mount Bracket z Wall Mount Bracket
Speed Dome Camera Instruction Manual
6
Page 7
Parts Name & Functions
Mount Adapter
Safety Retention Spring
Main Body
Gasket (PT112N-
XT Model only)
INTRODUCTION
Cabling Terminal Block
1
Lock-up Screw
DIP Switch
Dome Cover
Main Unit / Surface Mount Bracket
Back of Main Unit
z Dome Cover UDo not remove protective vinyl from dome cover before finishing all
installation processes to protect dome cover from scratches or dust.U
z Surface Mount Bracket The surface mount bracket is used for installing either a ceiling mount
or wall mount bracket. Separate the cover first and then attach it
directly to ceiling. Camera must be assembled at the last stage.
z Gasket (PT112N-XT
model only)
z Lockup Screw
z Cabling Terminal Block
Protect it from dust and rainstorm.
which should be placed on the low to main body position
Fixes main unit to surface mount bracket.
During installation, Power, Video, Communication, Alarm Input cables
are connected on to this cabling terminal block.
Pull out from Surface Mount Bracket and connect to Main Body hook.
Move projecting part of the gasket
z DIP Switch
z Fall-proof spring
Speed Dome Camera Instruction Manual
Adjusts camera ID and protocols.
After installing fall-proof spring on Bracket , hang on the safety ring to
protect the camera from falling
7
Page 8
INSTALLATION
Before you install the camera, you should set the DIP switches to configure the camera ID and communication
protocol.
DIP Switch Setup
2
Camera ID Setup
ON
ON
123456
Pin 1 2 3 4 5 6 7 8 Pin 1 2 3 4 5 6 7 8
ID 1 2 4 8 16 32 64 128 ID 1 2 4 8 16 32 64 128
1 on off off off off off off off 11 on on off on off off off off
2 off on off off off off off off 12 off off on on off off off off
3 on on off off off off off off 13 on off on on off off off off
4 off off on off off off off off 14 off on on on off off off off
5 on off on off off off off off 15 on on on on off off off Off
6 off on on off off off off off 16 off off off off on off off off
7 on on on off off off off off 17 on off off off on off off off
8 off off off on off off off off 18 off on off off on off off off
78
z The ID number of camera is set using a binary number. Examples
shown below.
z The range of ID is 1~255. UDo not use 0 as camera IDU. Fac t o r y
default of Camera ID is 1.
z If you want to control a certain camera, you must match the camera
ID with Cam ID setting of DVR or Controller.
9 on off off on off off off off 19 on on off Off on off off off
10 off on off on off off off off 20 off off on off on off off off
Speed Dome Camera Instruction Manual
8
Page 9
INSTALLATION
2
Pin 1 2 3 4 5 6 7 8
ID 1 2 4 8 16 32 64 128
21 on off on off on off off off
22 off on on off on off off off
23 on on on off on off off off
24 off off off on on off off off
25 on off off on on off off off
26 off on off on on off off off
27 on on off on on off off off
28 off off on on on off off off
29 on off on on on off off off
30 off on on on on off off off
Pin 1 2 3 4 5 6 7 8
ID 1 2 4 8 16 32 64 128
31 on on on on on off off off
32 off off off off off on off off
33 on off off off off on off off
34 off on off off off on off off
35 on on off off off on off Off
36 off off on off Off on off off
37 on off on off Off on off off
38 off on on off Off on off off
39 on on on off Off on off off
40 off off off on Off on off off
Communication Protocol Setup
ON
ON
1234
Reserved for Supplier
z Select the appropriate Protocol with DIP switch combination.
Switch State
P0
(Pin 1)
OFF OFF PELCO-D, 2400 bps
ON OFF PELCO-D, 9600 bps
OFF ON PELCO-P, 4800 bps
ON ON PELCO-P, 9600 bps
z If you want to control using DVR or P/T controller, their protocol must
be identical to camera. Otherwise, you
z If you changed camera protocol by changing DIP S/W, the change
will be effective after you reboot the camera.
z Factory default of protocol is “Pelco-D, 2400 bps”.
P1
(Pin 2)
Ucannot Ucontrol the camera.
Protocol
Speed Dome Camera Instruction Manual
9
Page 10
N
T
c
ON
O
1234
Terminal Resistor Setup
ON
ON
1234
INSTALLATION
z Pin 3 is only for supplier, UDO NOT CHANGE THESE ITS ORIGINAL
STATEU. If you change one of these, proper operation can not be
achieved.
~ Pin 3 PAL / NTSC system selection of Camera. UDO NOT
CHANGE THIS PINU.
erminal resistor is used if your system meets one of following two
onditional cases.
z Case1: Control cable between camera and controller is
relatively long (1:1 connection)
If communication cable is very long, the electrical signal will bind in
the terminal point. This reflected signal causes signal distortion,
resulting in a degradation of camera function. In this case, the
terminal resistor of both sides (i.e. camera and controller) must be
set to the ‘ON’ state.
2
z Case2: Multiple cameras are controlled at the same time
Due to similar reasons stated in case 1, the terminal resisters of the
controller and the last camera must be set to ‘ON’ state. The
camera with the longest cable length is determined to be the ‘last’
camera. Do not turn on the terminal resistor of all cameras.
Speed Dome Camera Instruction Manual
10
Page 11
After putting the Gasket on the ceiling
Fasten ceiling mount bracket to ceiling with 3
screws.
Installation using Ceiling Mount Bracket
② Wire cables to terminals and connect the
terminals to main unit. Do not use surface mount
bracket!
INSTALLATIONINSTALLATION
INSTALLATION
2
① Hang the camera on the safety ring and
assemble it using the fall-proof spring.
② Remove protective vinyl from dome cover.
Speed Dome Camera Instruction Manual
11
Page 12
① After putting the Gasket on the wall
Fasten wall mount bracket to ceiling with 4
screws.
Installation using Wall Mount Bracket
② Wire cables to terminals and connect the
terminals to main unit. Do not use surface
mount bracket!
INSTALLATION
2
③ Fasten main unit to wall mount bracket with 4
screws.
④ Remove protective vinyl from dome cover.
Speed Dome Camera Instruction Manual
12
Page 13
.
Cut 3 holes in ceiling
③ Connect fall-proof spring to main body
hook. Assemble and fasten with screws.
Installation using Flush Mount Bracket
② Align main body bracket with flush mount
④ Put main body and bracket assembly into
INSTALLATION
bracket. Fasten with screws.
main hole.
2
⑤ Secure flush mount bracket to the ceiling
Speed Dome Camera Instruction Manual
with screws through the 3 holes on the
bracket.
⑥ Cover assembly with bracket
cover and turn it clockwise.
13
Page 14
Power Connection
z Please check the voltage and current capacity of rated power carefully. Rated power is indicated on the
back of main unit.
Cabling
Controller/ DVR
Moinitor
BNC
Power
PWR(+)
PWR(-)
F.G
RS-485(+)
RS-485(-)
VIDEO(+)
VIDEO(-)
Cabling Terminal Block
IN COM+
IN1
IN2
IN3
IN4
INSTALLATION
IrDA
Sensor
Door
Switch
Sensor
2
Rated Power Input Voltage Range Current Consumption
AC 24V (PT112N) AC 17V ~ 29V 0.4 A
AC 24V (PT112N-XT) AC 17V ~ 29V 1.5 A
z DC power loss increases over distance. DC power wiring to cameras should be kept as short as possible.
RS-485 Communication
z For PTZ control, connect the RS-485 line to keyboard and DVR. To control multiple cameras on the same line
with simultaneous operation (see page 13 for resistor settings): the RS-485 communication lines to cameras
are connected in parallel as shown below.
Speed Dome Camera Instruction Manual
14
Page 15
Video Connection
z Connect with BNC coaxial cable.
Alarm Input Connection
z Sensor Input
Internal
SENSOR IN1
SENSOR COM
(GND)
SENSOR IN2
SENSOR COM
(GND)
SENSOR IN3
INSTALLATION
2
Before connecting sensors, check the sensor driver voltage and output signal type. Since sensor output
signal types are divided into Open Collector and Voltage Output types in general, the cabling must be
installed properly depending on the signal type.
Signal Description
IN COM (GND) Connect SENSOR COMs to this port(GND) as shown in the circuit above.
IN1, IN2, IN3, IN4 Connect output of sensors for each port as shown in the circuit above.
SENSOR COM
(GND)
SENSOR IN4
SENSOR COM
(GND)
Speed Dome Camera Instruction Manual
15
Page 16
INSTALLATION
If you want to use Alarm Input, the type of sensor must be selected in OSD menu. The sensor types are
Normal Open and Normal Close. If the sensor type is not selected properly, alarm activation will occur
opposite of what is desired.
~ Normal Open Output Voltage is high state when sensor is activated
~ Normal Close Output Voltage is high state when sensor is not activated
2
Speed Dome Camera Instruction Manual
16
Page 17
z Before power is applied, please check the cables carefully.
z The camera ID of the controller must be identical to that of the target camera. The camera ID can be checked by
reading DIP switch of the camera.
z If your controller supports multi-protocols, the protocol must be changed to match to that of the camera.
z If you changed camera protocol by changing DIP switch, the change will be effective after you reboot the
camera.
z Since the operation method can be different for each controller available, refer to the manual for your controller
if camera can not be controlled properly. The operation of this manual is based on the standard Pelco®
Controller.
Check Points before Operation
Preset and Pattern Function Pre-Check
OPERATION
3
z Check controller or DVR preset and pattern functions in advance when using controller or DVR.
z Refer to the following table when using standard Pelco® protocol controller.
< Go Preset > Input [Preset Number] and press [Preset] button.
< Set Preset > Input [Preset Number] and press [Preset] button for more than 2 seconds.
< Run Pattern > Input [Pattern Number] and press [Pattern] button.
< Set Pattern > Input [Pattern Number] and press [Pattern] button for more than 2 seconds.
z If controller or DVR has no pattern button or function, use shortcut keys with preset numbers. For more
information, refer to “Reserved Preset” in this manual.
Speed Dome Camera Instruction Manual
17
Page 18
OPERATION
Starting OSD Menu
z Function Using the OSD menu, Preset, Pattern, Swing, Group and Alarm Input function can be
configured for each application
z Enter Menu <Go Preset> [95]
Reserved Preset
z Description Some Preset numbers are reserved to special functions.
z Function Go Preset [95] : Enters into OSD menu
Go Preset [131~134] : Runs Pattern Function 1 ~ 4
Go Preset [141~148] : Runs Swing Function 1 ~ 8
Go Preset [151~158] : Runs Group Function 1 ~ 8
3
Go Preset [170] : Sets Camera BLC Mode to OFF
Go Preset [171] : Sets Camera BLC Mode to ON
Go Preset [174] : Sets Camera Focus Mode to AUTO
Go Preset [175] : Sets Camera Focus Mode to Manual
Go Preset [176] : Sets Camera Focus Mode to SEMI-AUTO
Go Preset [177] : Sets Day & Night Mode to AUTO
Go Preset [178] : Sets Day & Night Mode to NIGHT
Go Preset [190] : Sets OSD Display Mode to AUTO (Except Privacy Mask)
Go Preset [191] : Sets OSD Display Mode to OFF (Except Privacy Mask)
Go Preset [192] : Setting OSD Display Mode to ON (Except Privacy Mask)
Go Preset [193] : Sets all Privacy Mask Display to OFF
Go Preset [194] : Sets all Privacy Mask Display to ON
Go Preset [179]
Go Preset [182]
Go Preset [183]
: Sets Day & Night Mode to DAY
: Sets Camera IRIS mode to AUTO
: Sets Camera IRIS mode to Manual
Speed Dome Camera Instruction Manual
18
Page 19
OPERATION
Preset
z Function Max. 127 positions can be stored as Preset position. The Preset number can be
assigned from 1 to 128, but 95 is reserved for starting OSD menu.
Camera characteristics (i.e. White Balance, Auto Exposure) can be set up
independently for each preset. Label should be blank and "Camera Adjust" should be
set to "GLOBAL" as default. All characteristics can be set up in OSD menu.
z Set Preset <Set Preset> [1~128]
z Run Preset <Go Preset> [1~128]
z Delete Preset To delete Preset, use OSD menu.
Swing
3
z Function By using Swing function, the camera can move between 2 Preset positions repeatedly.
When swing function runs, camera moves from the preset assigned as the 1st point to
the preset assigned as the 2nd point in CW (Clockwise) direction. Then camera moves
from the preset assigned as the 2nd point to the preset assigned as the 1st point in
CCW (Counterclockwise) direction.
1
1st Preset
n
o
i
t
c
e
r
i
D
W
C
D
W
C
C
2
c
e
r
i
n
o
i
t
2nd Preset
If the preset assigned as the 1st point is the same as the preset assigned as the 2nd
point, the camera will turn 360° in a CW (Clockwise) direction, then 360° in a CCW
(Counterclockwise) direction.
Speed can be set up from 1°/sec to 180°/sec.
z Set Swing To set Swing, use OSD menu.
z Run Swing Method 1) <Run Pattern> [Swing NO.+10]
Method 2) <Go Preset> [Swing NO.+140]
ex) Run Swing 3 : <Run Pattern> [13]
ex) Run Swing 3 : <Go Preset> [143]
z Delete Swing To delete Swing, use OSD menu.
Speed Dome Camera Instruction Manual
19
Page 20
OPERATION
Pattern
z Function Pattern Function allows the camera to memorize a path (often a curved path) created
by controller joystick for an assigned time. The camera will then retrace the path
exactly as memorized.
4 Patterns are available and Maximum 1200 communication commands can be stored
in a pattern.
z Set Pattern Patterns can be created by one of following two methods.
Method 1) <Set Pattern> [Pattern NO.]
{ Pattern editing screen is displayed as bellow.
EDIT PATTERN 1
3
[NEAR:SAVE /FAR:DELETE]
0/0/x1/N
{ Movement by Joystick and preset movement can be memorized in a pattern.
{ The remaining memory size is displayed in progress bar.
{ To save the recording, press NEAR key and to cancel, press FAR key.
Method 2) OSD Using OSD Menu: See the section “How to use OSD Menu”.
z Run Pattern Method 1) <Run Pattern> [Pattern NO.]
Method 2) <Go Preset> [Pattern NO.+130]
z Delete Pattern Use OSD menu to delete a Pattern.
ex) Run Pattern 2 : <Run Pattern> [2]
ex) Run Pattern 2: <Go Preset> [132]
Speed Dome Camera Instruction Manual
20
Page 21
z Function The group function allows a running sequence of Presets, Pattern and/or Swings. Max
z Set Group Use OSD Menu to create a Group.
Group
8 groups can be stored. Each group can have max 20 action entities which can be
preset, pattern or swing. Preset speed can be set up and the repeat number of Pattern
& Swing can be set up in Group setup. Dwell time between actions can also be set up.
Dwell Time
Preset 1 Pattern 1 Swing 1
Max 20 Entities
OPERATION
3
z Run Group Method 1) <Run Pattern> [Group NO.+20]
Method 2) <Go Preset> [Group NO.++150]
z Delete Group Use OSD Menu to delete.
ex) Run Group 7 : <Run Pattern> [27]
ex) Run Group 7 : <Go Preset> [157]
Speed Dome Camera Instruction Manual
21
Page 22
OPERATION
Other Functions
z Power Up Action This function enables the camera to resume the last action executed before power
down. Most actions such as Preset, Pattern, Swing and Group are available for this
function, but Jog actions cannot be resumed.
z Auto Flip If the tilt angle arrives at the top of tilt orbit (90°), zoom module camera will keep
moving in the opposite tilt direction (180°) to keep tracing targets. As soon as the
camera (lens) passes through the top of tilt direction (90°), images will be reversed
automatically and the F symbol appears on screen. If this function is set to OFF, tilt
movement range is 0 ~ 95°.
z Parking Action This function sets the camera to a specific position automatically if operator doesn’t
operate the controller for a while. The Park Time can be defined as an interval from 1
minute to 4 hours.
z Alarm Input 4 Alarm Inputs are used. If an external sensor is activated, camera can be set to move
to corresponding preset position. Note: the latest alarm input is in effect if multiple
sensors are activated.
3
z Privacy Zone Mask To protect privacy, MAX. 8 Privacy Masks can be created in arbitrary locations to hide
objects such as windows, shops or private houses. With the Spherical Coordinates
system, a powerful Privacy Zone Mask function is available.
z GLOBAL/LOCAL
Image Setup
z Semi-Auto Focus
WB (White Balance) and AE (Auto Exposure) can be set up independently for each
preset. There are 2 modes, "Global" mode & "Local" mode. The Global mode means
that WB or AE can be set up simultaneously for all presets in the "ZOOM CAMERA
SETUP" menu. The Local mode means that WB or AE can be set up independently or
separately for each preset in each preset setup menu. Each Local WB/AE value will
activate correspondingly as the camera arrives at each preset location.
During jog operation, Global WB/AE values should be applied. All Local WB/AE
values will not change although Global WB/AE value changes.
Automatically selects focus mode from Manual Focus or Auto Focus depending on type
of operation. Manual Focus mode activates in preset operation and Auto Focus mode
activates during jog operation. In Manual mode, Focus data for each preset is
memorized in advance, and the camera calls focus data for corresponding presets as
soon as it arrives at a preset. This method shortens focus times.
Focus mode changes to Auto Focus mode automatically when jog operation starts.
Speed Dome Camera Instruction Manual
22
Page 23
OSD Display of Main Screen
Preset Label
Image Flip
Camera ID
LABEL12345 PRESET1
F I:1--4
CAM 1 15/4/x1/N
P/T/Z Information
OPERATION
Action Title
Alarm Information
3
z P/T/Z Information Current Pan/Tilt angle in degree, zoom magnification and a compass direction.
z Camera ID Current Camera ID (Address).
z Action Title
z Preset Label The Label stored for specific Preset.
z Alarm Input This information shows current state of Alarm Input. If an Input point is ON it will show
Followings are possible Action Titles and their meaning.
"SET PRESET ×××" When Preset ××× is stored
"PRESET ×××" When camera reach to Preset ×××
"PATTERN ×" When Pattern × is in action
"SWG×/PRESET ×××" When Swing × is in action
"UNDEFINED" When undefined function is called to run
a number corresponding to each point. If an Input point is OFF, '-' will be displayed.
Example - if points 2 & 3 of inputs are ON, the OSD will show as below:
I:-23-
z Image Flip Indicates that images are currently reversed by Auto Flip Function.
Speed Dome Camera Instruction Manual
23
Page 24
HOW TO USE OSD MENU
General Rules of Key Operation for Menu
z The menu items surrounded with ( ) always have a sub menu.
z At all menu levels, to go into sub menu, press NEAR key.
z To go to up one menu level, press FAR key.
z To move from items to item in the menu, use joystick in the Up/Down or Left/Right.
z To change a value of an item, use Up/Down of the joystick in the controller.
z Press NEAR key to save values and Press FAR key to cancel values.
Main Menu
SPEED DOME CAMERA
----------------------- <SYSTEM INFORMATION>
<DISPLAY SETUP>
<DOME CAMERA SETUP>
<SYSTEM INITIALIZE>
z System Information Displays system information and
configuration.
z Display Setup Enable/Disable of OSD display on Main
Screen.
4
EXIT
z Dome Camera Setup
z System Initialize Initializes system configuration and sets all
Configure various functions of this camera.
data to factory default configuration.
Speed Dome Camera Instruction Manual
24
Page 25
DISPLAY SETUP
----------------------- CAMERA ID ON
PTZ INFORMATION AUTO
ACTION TITLE AUTO
PRESET LABEL AUTO
ALARM INPUT AUTO
<SET NORTH DIRECTION>
<PRIVACY ZONE>
BACK
EXIT
Display Setup
HOW TO USE OSD MENU
This menu defines Enable/Disable of OSD display on Main Screen. If an
item is set to be AUTO, the item is displayed only when the value of it is
changed.
z Camera ID [ON/OFF]
z PTZ Information [ON/OFF/AUTO]
z Action Title [ON/OFF/AUTO]
z Preset Label [ON/OFF/AUTO]
z Alarm Input [ON/OFF/AUTO]
4
Compass Direction Setup
SET NORTH DIRECTION
------------------------
MOVE TO TARGET POSITION
[NEAR:SAVE /FAR:CANCEL
Set North to assign compass direction as criteria. Move camera and
press NEAR button to save.
Speed Dome Camera Instruction Manual
25
Page 26
PRIVACY ZONE
----------------------- MASK NO 1
UNDEFINED
DISPLAY OFF
CLEAR MASK CANCEL
<EDIT MASK>
BACK
EXIT
Privacy Zone Mask Setup
Select area in image to mask.
z Mask No [1~8]
z Display [ON/OFF]
z Clear Mask [CANCEL/OK]
HOW TO USE OSD MENU
Select Mask number. If the selected mask has
already data, camera moves as it was set.
Otherwise, “UNDEFINED” will be displayed
under “Mask NO”.
Sets if camera makes mask shows or not on
images.
Deletes data in the selected mask NO.
4
Privacy Zone Area Setup
EDIT MASK 1
------------------------
MOVE TO TARGET POSITION
[NEAR:SELECT/FAR:CANCEL]
Privacy Zone Size Adjustment
EDIT MASK 1
------------------------
[ :ADJUST MASK WIDTH]
[ :ADJUST MASK HEIGHT]
[NEAR:SAVE /FAR:CANCEL]
Move camera to area to mask. Then the menu to adjust mask size will be
displayed.
Adjust mask size. Use joystick or arrow buttons to adjust mask size.
z (Left/Right)
z (Up/Down)
Speed Dome Camera Instruction Manual
26
Page 27
ZOOM CAMERA SETUP
----------------------- FOCUS MODE SEMIAUTO
DIGITAL ZOOM ON
IMAGE FLIP OFF
SHARPNESS 2
STABILIZATION OFF
<WHITE BALANCE SETUP>
<AUTO EXPOSURE SETUP>
BACK
EXIT
Camera Setup
HOW TO USE OSD MENU
Setup the general functions of zoom camera module.
z Focus Mode [AUTO/MANUAL/SEMIAUTO]
Sets camera focus mode.
{
USEMIAUTO Mode
Automatically selects focus mode from
Manual Focus or Auto Focus depending on
type of operation. Manual Focus mode
activates in preset operation and Auto Focus
mode activates during jog operation. In
Manual mode, Focus data for each preset is
memorized in advance, and the camera calls
focus data for corresponding presets as soon
as it arrives at a preset.
4
z Digital Zoom [ON/OFF]
Sets digital zoom function to ON/OFF. When
set to OFF, optical zoom function runs but
zoom function stops at the end of optical zoom
magnification.
zImage Flip
z Sharpness [0~3]
z Stabilization [ON/OFF]
[ON/OFF]
Turn watching direction to the other side of
moving when camera gets vertical sight.
Sets image sharpness to enhance pictures.
Compensates image vibrations by wind or
others. The images with vibrations are
compensated by Digital Zoom function
Speed Dome Camera Instruction Manual
and the image resolution with this function
should be lower than normal image when
this function is turned off.
27
Page 28
White Balance set up
WB SETUP - GLOBAL
----------------------- WB MODE AUTO
RED ADJUST -- BLUE ADJUST ---
BACK
EXIT
HOW TO USE OSD MENU
z WB Mode [AUTO/MANUAL]
In Manual mode, Red and Blue level can be
set up manually
z Red Adjust [0~255]
z Blue Adjust [0~255]
4
Speed Dome Camera Instruction Manual
28
Page 29
Auto Exposure Setup
AE SETUP - GLOBAL
----------------------- BACKLIGHT OFF
DAY/NIGHT AUTO
BRIGHTNESS 32
IRIS AUTO
SHUTTER -- AGC -- SSNR MIDDLE
SENS-UP <AUTO>
BACK
EXIT
HOW TO USE OSD MENU
z Backlight [ON/OFF]
Sets Backlight Compensation
z Day/Night [AUTO/DAY/NIGHT]
Sets up Day&Night mode
z Brightness [0~64]
Adjusts brightness of images. Iris, Shutter
z IRIS [AUTO/MANUAL(0~64)]
Speed and Gain are adjusted automatically in
correspondence with this value.
If Iris is set to Auto, Iris should have highest
priority in adjusting AE and Shutter Speed
should be fixed.
If Iris is set to Manual, Iris should be fixed and
Iris has lower priority in adjusting AE, in
comparison with others.
4
z Shutter Speed [A.Flicker/Manual(1/60(50)~1/10000 sec)]
If Iris is set to Manual and Shutter Speed is set
to ESC, Shutter Speed should have highest
priority. If Shutter Speed is set to A.Flicker, to
remove Flicker, Shutter Speed should be set
to 1/100 sec. for NTSC and 1/120 for PAL.
z AGC [OFF/LOW/MIDDLE/HIGH/MANUAL(0~15)]
Enhances image brightness automatically in
case that luminance level of image signal is
too low.
z SSNR [OFF/LOW/MIDDLE/HIGH]
Enhances images by filtering noise when gain
level of images is too high.
z SENS-UP [AUTO(2~256)/OFF]
Activates Slow Shutter function when
luminance of image (signal) is too dark.
It is possible to set up the maximum number
of frames stacked on one another by Slow
Shutter function.
Speed Dome Camera Instruction Manual
29
Page 30
MOTION SETUP
----------------------- MOTION LOCK OFF
PWR UP ACTION ON
AUTO FLIP ON
JOG MAX SPEED 120/SEC
JOG DIRECTION INVERSE
FRZ IN PRESET OFF
<PARKING ACTION SETUP>
<ALARM INPUT SETUP>
BACK
EXIT
Motion Setup
HOW TO USE OSD MENU
Setup the general functions of Pan/Tilt motions.
z Motion Lock [ON/OFF]
If Motion Lock is set to ON, it is impossible to
set up and delete Preset, Swing, Pattern and
Group. It is only possible to run these
functions. To set up and delete these
functions, enter into OSD menu.
z Power Up Action [ON/OFF]
Refer to “Other Functions" section.
z Auto Flip [ON/OFF]
Refer to “Other Functions" section.
z Jog Max Speed [1°/sec ~360°/sec]
Sets maximum jog speed. Jog speed is
inversely proportional to zoom magnification.
As zoom magnification goes up, pan/tilt
speed goes down.
4
z Jog Direction [INVERSE/NORMAL]
If you set this to ‘Inverse’, the view on the
screen will move in the same direction as jog
tilt. If ‘Normal’ is selected, the view on the
screen will move in the opposite direction.
z Freeze in Preset [ON/OFF]
At start point of preset movement, camera will
freeze the image of start point. Camera keeps
displaying the image of start point during
preset movement and does not display the
images received during preset movement. As
soon as camera stops at preset end point,
camera will display live images received at
the preset end point.
Availability of this function will vary by
model.
Speed Dome Camera Instruction Manual
30
Page 31
Parking Action Setup
PARKING ACTION SETUP
----------------------- PARK ENABLE OFF
WAIT TIME 00:10:00
PARK ACTION HOME
BACK
EXIT
HOW TO USE OSD MENU
If Park Enable is set to ON, camera runs assigned function automatically
if there is no PTZ command during assigned "Wait Time".
z Park Enable [ON/OFF]
z Wait T im e [ 1~59 sec/1~180 minute]
The time is displayed with "hh:mm:ss" format
and can be changed in 1 min units.
z Park Action [HOME/PRESET/PATTERN/SWING/GROUP]
{
UHOME
Camera moves to home position if there is no
PTZ command during assigned "Wait Time".
4
Alarm Input Setup
ALARM INPUT SETUP
----------------------- ALARM NO. 1
TYPE N.OPEN
ACTION NOT USED
HOLD TIME ENDLESS
POST ACTION HOME
BACK
EXIT
Matches the Alarm sensor input to one of Preset positions. If an external
sensor is activated, camera will move to corresponding preset position
when this item is predefined.
z Alarm × Type [Normal OPEN/Normal CLOSE]
Sets sensor input type.
z Alarm × Action [NOT USED/PRESET/PATTERN,SWING/GROUP]
Assign counteraction Preset position to each
Alarm input.
z Hold Time [ENDLESS/1~59 sec/1~180 minute]
Sets the time period for the action which is run
by external sensor activation. After the time
period passes, the action pre-defined in “Post
Action” runs sequentially in succession to the
action by external sensor activation. If this option
is set to “ENDLESS”, “Post Action” does not
activate.
Speed Dome Camera Instruction Manual
z Post Action [HOME/PRESET/PATTERN/SWING/GROUP/PREV
ACTION]
31
Page 32
PRESET SETUP
----------------------- PRESET NO. 1
CLR PRESET CANCEL
<EDIT SCENE>
<EDIT LABEL> LABEL123
CAM ADJUST GLOBAL
BACK
EXIT
Preset Setup
HOW TO USE OSD MENU
z Preset Number [1~128]
If a selected preset is already defined, camera
moves to pre-defined position and preset
characteristics such as Label and Relay Outputs
show on monitor. If a selected preset is not
defined, “UNDEFINED” shows on monitor.
z Clear Preset [CANCEL/OK]
Delete current Preset data
z Edit Preset Scene Redefine current Preset scene position (i.e.
PTZ).
4
Edit Preset Scene
EDIT SCENE - PRESET 1
------------------------
MOVE TO TARGET POSITION
[NEAR:SAVE /FAR:CANCEL]
○1 Using Joystick, move camera to desired position.
2
○
By pressing NEAR key, save current PTZ data.
3
○
Press FAR key to cancel.
Speed Dome Camera Instruction Manual
32
Page 33
SWING SETUP
----------------------- SWING NO. 1
1ST POS. NOT USED
2ND POS. NOT USED
SWING SPEED 30/SEC
CLEAR SWING CANCEL
BACK
EXIT
Swing Setup
HOW TO USE OSD MENU
z Swing Number [1~8]
z 1st Position
2nd Position
4
Select Swing number to edit. If a selected Swing is
not defined, "NOT USED" is displayed in 1st
Position and 2nd Position
[PRESET 1~128]
Set up the 2 position for Swing function. If a
selected preset is not defined, "UNDEFINED" will
be displayed as shown below.
SWING SETUP
----------------------- SWING NO. 1
1ST POS. PRESET5
2ND POS. NOT USED
UNDEFINED
When swing function runs, the camera will move
from the preset assigned as the 1st point to the
preset assigned as the 2nd point in a CW
(Clockwise) direction. Then the camera will move
from the preset assigned as the 2nd point to the
preset assigned as the 1st point in a CCW
(Counterclockwise) direction. If the preset
assigned as the 1st point is same as the preset
assigned as the 2nd point, the camera will turn
360° in CW direction and then turn 360° in CCW
direction.
z Swing Speed [1°/sec ~180°/sec]
Sets Swing speed from 1°/sec to 180°/sec.
z Clear Swing [CANCEL/OK]
Deletes current Swing data.
Speed Dome Camera Instruction Manual
33
Page 34
PATTERN SETUP
----------------------- PATTERN NO. 1
UNDEFINED
CLR PATTERN CANCEL
RUN PATTERN
<EDIT PATTERN>
BACK
EXIT
Pattern Setup
HOW TO USE OSD MENU
z Pattern Number [1~4 ]
z Clear Pattern
z Run Pattern
4
Selects Pattern number to edit.
If a selected pattern number is not defined,
"UNDEFINED" will be displayed under
selected pattern number.
[CANCEL/OK]
Deletes data in current pattern
Runs Pattern for the test purposes to check if
it works properly.
Edit Pattern
EDIT PATTERN 1
------------------------
MOVE TO START POSITION
[NEAR:START /FAR:CANCEL]
EDIT PATTERN 1
z Edit Pattern Starts editing pattern.
① Using Joystick, move to start position with appropriate zoom. To
start pattern recording, press NEAR key. To exit this menu, press
FAR key.
② Move camera with controller joystick or run preset function to
memorize a path (often a curved path) in a selected pattern. The
total memory size and remaining memory size are displayed in
the form of a bar. Maximum 1200 communication commands can
be stored in a pattern.
[NEAR:SAVE /FAR:DELETE]
0/0/x1/N
Speed Dome Camera Instruction Manual
③ To save data and exit, press NEAR key. To cancel recording and
delete record data, press FAR key.
34
Page 35
GROUP SETUP
----------------------- GROUP NO. 1
UNDEFINED
CLEAR GROUP CANCEL
RUN GROUP
<EDIT GROUP>
BACK
EXIT
Edit Group
EDIT GROUP 1
----------------------- NO ACTION ### DWELL OPT
----------------------- 1 NONE
2 NONE
3 NONE
4 NONE
5 NONE
----------------------- SAVE
CANCEL [NEAR:EDIT]
Group Setup
HOW TO USE OSD MENU
z Group Number [1~8]
Selects Group number to edit.
If a selected Group number is not defined,
"UNDEFINED" will be displayed under selected
Group number.
z Clear Group
z Run Group
z Edit Group Starts editing Group.
① “Press Near key in “NO” list to start Group setup.
[CANCEL/OK]
Deletes data in current Group
Runs Group for the test purposes.
4
EDIT GROUP 1
----------------------- NO ACTION ### DWELL OPT
----------------------- 1 NONE
2 NONE
3 NONE
4 NONE
5 NONE
----------------------- SAVE [NEAR:EDIT ACT]
CANCEL [FAR :EDIT END]
EDIT GROUP 1
----------------------- NO ACTION ### DWELL OPT
----------------------- 1 NONE
2 NONE
3 NONE
4 NONE
5 NONE
----------------------- SAVE [ :MOVE CURSOR]
CANCEL [ :CHANGE VAL.]
② Note that MAX. 20 Functions are allowed in a Group. Move cursor
up/down and press Near key to set up.
③ Set up Action, Dwell time and Option. Note that selected item is
displayed in reverse. Move cursor Left/Right to select items and
move cursor Up/Down to change each value.
z Action ### [NONE/PRESET/SWING/PATTERN]
z DWELL [0 second ~ 4 minutes]
Sets Dwell Time between functions
z OPT Option. Displays the preset speed when
preset is set in Action. Displays the number
of repeats when Pattern or Swing is selected
in Action
Speed Dome Camera Instruction Manual
35
Page 36
EDIT GROUP 1
----------------------- NO ACTION ### DWELL OPT
----------------------- 1 PRESET 1 00:03 360
2 NONE
3 NONE
4 NONE
5 NONE
----------------------- SAVE [ :MOVE CURSOR]
CANCEL [ :CHANGE VAL.]
EDIT GROUP 1
----------------------- NO ACTION ### DWELL OPT
----------------------- 1 PRESET 1 00:03 360
2 NONE
3 NONE
4 NONE
5 NONE
----------------------- SAVE [NEAR:EDIT ACT]
CANCEL [FAR :EDIT END]
HOW TO USE OSD MENU
④ Set up items such as Action, ###, Dwell and OPT.
⑤ After finishing setup of an Action, press Near key to one-upper-
level menu (Step ②). Move cursor Up/Down to select Action
number and repeat Step ② ~ Step ④ to edit selected Group.
4
EDIT GROUP 1
----------------------- NO ACTION ### DWELL OPT
----------------------- 1 PRESET 1 00:03 360
2 NONE
3 NONE
4 NONE
5 NONE
----------------------- SAVE
CANCEL
⑥ After finishing setup of all Actions, press FAR key to exit. Then
cursor should be moved to “SAVE”. Press Near key to save data.
Speed Dome Camera Instruction Manual
36
Page 37
SYSTEM INITIALIZE
----------------------- CLEAR ALL DATA NO
CLR DISPLAY SET NO
CLR CAMERA SET NO
CLR MOTION SET NO
CLR EDIT DATA NO
REBOOT CAMERA NO
REBOOT SYSTEM NO
BACK
EXIT
System Initialize
HOW TO USE OSD MENU
z Clear All Data Deletes all configuration data, such as display,
camera, and motion setup.
z Clear Display Set Initializes Display Configuration
z Clear Camera Set Initializes Camera Configuration
z Clear Motion Set Initializes Motion Configuration
z Clear Edit Data Deletes Preset Data, Swing Data, Pattern Data
and Group Data
z Reboot Camera Reboots Zoom Camera module
z Reboot System Reboots Speed Dome Camera
4
Initial Configuration Table
z Display Configuration z Camera Configuration
Camera ID ON Focus Mode SemiAuto
PTZ Information AUTO Digital Zoom ON
Action Title AUTO Image Flip OFF
Preset Label AUTO Sharpness 2
Alarm Input AUTO Stabilization OFF
North Direction Pan 0° White Balance AUTO
Privacy Zone Undefined Backlight OFF
Day&Night AUTO
z Motion Configuration Brightness 32
Motion Lock OFF Iris AUTO
Power Up Action ON Shutter ---
Auto Flip ON AGC ---
Jog Max Speed 120°/sec SSNR MIDDLE
Jog Direction INVERSE SENS-UP AUTO
Freeze In Preset OFF z User Edit Data
Park Action OFF Preset 1~128 Undefined
Alarm Action OFF Swing 1~8 Undefined
Pattern 1~4 Undefined
Group 1~8 Undefined
Speed Dome Camera Instruction Manual
37
Page 38
SPECIFICATIONS
Model PT112N / PT112N-XT ×12 Appearance*
Video Signal System NTSC PAL
Camera
Pan/Tilt
General
* PT112N-XT Model Only
** Check the voltage and current capacity of rated power carefully.
*** Specifications of this product are subject to change without notice.
Specifications
CCD 1/4'' Super-HAD CCD
Max. Pixels 811(H)×508(V) 410K 795(H)×596(V) 470K
Effective Pixels 768(H)×494(V) 380K 752(H)×582(V) 440K
Horizontal Res. 560 TVL (Color), 600 TVL (B/W)
S/N Ratio 52 dB (AGC Off)
Zoom ×12 Optical Zoom, ×12 Digital Zoom
Focal length F1.6, f=3.6~44.3mm
Min.
illumination
Day & Night Auto / Day / Night(ICR)
Focus Auto / Manual / SemiAuto
Iris Auto / Manual
Shutter Speed 1/60(50) ~ 1/10000 sec
AGC Auto / Manual
White Balance Auto / Manual(Red, Blue Gain Adjustable)
BLC On / Off
Flickerless Selectable
SSNR Low / Middle / High / Off
Range
Pan/Tilt Speed
Preset 127 Preset (Label, Camera Image Setting)
Pattern 4 Pattern, 880 commands(about 5 minute)/Pattern
Swing 8 Swing
Group 8 Group (20 action entities per Group)
Other Functions Auto Flip, Auto Parking, Power Up Action etc.
Communication RS-485
Protocol Pelco-D, Pelco-P selectable
Privacy Zone 8 Zone
Alarm Input 4 Input
OSD Menu / PTZ information etc
Rated Power**
Dimension
Wei g ht
Operating
Temp.
IEC-529
Standard
2.0 Lux (Color) / 0. 0008 Lux (B/W), 50 IRE
Pan : 360°(Endless)
Tilt : 180° (Auto-Flip), 95° (Normal)
Preset : 360°/sec
Manual
Swing : 1~ 180°/sec
0.05 ~ 360°/sec (proportional to zoom)
:
DC Type : DC 12V / 0.8A , *DC 12V / 2.5A
AC Type : AC 24V / 0.4A , *AC 24V / 1.5A
Dome : ∅115
Ceiling ∅178× 233(H) mm
Housing
Main Unit Approx. about 1.3 Kg, *1.9 Kg
Ceiling Approx. *2.2Kg
Wall Approx. *2.5Kg
0°C ~ 40°C , (*-30 ~ 50°C / -22~ 122°F)
∅154.5 × 158.5(H) mm , *∅178
× 244(H)×289(H) mm
*IP66
Note: PT112N-XT. PT112N appearance will vary, see
page 38 for PT112N appearance specifications.
Main Unit
Ceiling
Wa ll
Sun shield
5
Speed Dome Camera Instruction Manual
38
Page 39
z Main Unit & Surface Mount Bracket z Ceiling Mount Bracket
Dimensions-PT112N Indoor Model
SPECIFICATIONS
5
z Wall Mount Bracket
UUnit: mm
Speed Dome Camera Instruction Manual
39
Page 40
z Ceiling Mount Bracket
Dimensions-PT112N-XT Outdoor Model
z Sun shield
SPECIFICATIONS
5
z Wall Mount Bracket
UUnit: mm
Speed Dome Camera Instruction Manual
40
Page 41
NOTES:
Speed Dome Camera Instruction Manual
41
Loading...