Ganz PMA1 User Manual

WB-1, JB-1, PMA-1

Feed-through Mounts

& Accessories

Instructions for Use

SAFETY PRECAUTIONS

The exclamation point within an equilateral triangle is
intended to alert the user to presence of important oper­ating and maintenance (servicing) instructions in the liter­ature accompanying the appliance.

SECURITE

Le point d'exclamation à l'intérieur d'un triangle équilatéral avertit

l'utilisateur de la présence
d'instructions importantes d'utilisation et de
maintenance dans la documentation accompagnant
l'appareil.

SICHERHEITSVORKENHRUNGEN

Das Ausrufezeichen in dem gleichseitigen Dreieck ist dazu da, den

Benutzer auf wich-tige
Inbetriebnahme- und Instandhaltungs-vorschriften
hinzuweisen, die dem Gerät in Form einer Broschüre
beigelegt sind.

PRECAUCIONES DE SEGURIDAD

El símbolo de exclamación dentro de un triángulo equi­látero, se muestra con el objetivo de alertar al ususario
de que instrucciones de operación y
mantenimiento importantes acompañan al equipo.

1UNPACKING

Unpack carefully. This is mechanical equipment and should be han­dled with care.

Check for the following items:

n Verify the unit model number.
n Instructions for Use.

If an item appears to have been damaged in shipment, replace it prop­erly in its carton and notify the shipper. If any items are missing, con­tact the company from which the unit was purchased.

The shipping carton is the safest container in which the unit may be

transported. Save it for possible future use.

2SERVICE

If the unit ever needs repair service, the customer should
contact the company from which the unit was purchased for authori­zation to return and shipping instructions.

3DESCRIPTION

WB1 18-cm (7-in) and JB1 40-cm (15-in) Feed-through Mounts.

This indoor/outdoor mounting equipment is designed for fixed cam­era or camera housing installations up to 9 kg (20 lb) rated load.
These models are made of lightweight aluminum and feature welded
construction, providing an extremely rigid camera mount. These
brackets have been specifically designed for the H1 & H2 series
housings. All mounts come fully assembled.

4INSTALLATION

4.1 WB-1, JB-1

1. Determine a secure wall mounting location.

2

WARNING: All mounts are deisgned to support a load only
in a vertical direction. Mounts MUST be positioned as

shown under SPECIFICATIONS.

2.
Cautions:

a. For a secure installation, use four 8-mm (5/16-in) diameter

fasteners (not included). Use stainless steel or zinc plated
fasteners.

b. If bolts are used, they should extend through the mounting

surface and be secured with flat washers, lock washers, and
nuts on the opposite side. Each bolt must have a
minimum pull-out strength of 200 kg (450 lb).

c. If studs are used, they should be anchored in concrete or

welded to a steel backer plate. Each stud must have a mini­mum pull out strength of 200 kg (450 lb).

d. If the wall mount is attached to wood or to a blind

structure (with no access to the rear), each fastener
must have a minimum pull-out strength of at least 200 kg
(450 lb).

3. Locate the four holes or stud locations using the flange as a

template (four holes equally spaced on a 69.9-mm (2-3/4-in bolt
circle).

4. Feed wires through the large hole in the flange or through the

slot on the surface where the camera housing mounts.

5. Install the mount using bolts or studs at least 8-mm (5/16-in) in

diameter.

6. To mount the camera or camera housing:

a. Mount camera with a 1/4-20 bolt and lock washer (not

furnished) in the center hole of the adjustable head.

b. Mount housings with three 1/4-20 bolts and lock

washers (not furnished).

c. Lock mount head in position by using the supplied

1/8-inch long-arm hex wrench to tighten screws.

4.2 PMA-1 Pole mount Adapter

1. Tools required

8mm Hex Wrench
Banding Tool (PMA-1 recommended)

2. Mounting

1. Attach the bracket to the pole at the desired height using the

two straps and two buckles provided.

2. Tension the straps according to the instructions for the banding

tool. BAND-IT, Banding tool is recommended and may be pur­chased seperately. A BAND-IT Tool Instruction Chart is provid­ed with each pole mount. Figure 1. shows how the ends of the
bands are bent around the buckle.

Figure 1: Banding Method

Tension and
Bend Back Bands

Bend Buckle
Tab Over Bands