Ganz LC702N User Manual

www.computarganz.com

Color Video Camera

Instruction Manual

Models : LC703

LC702
LC701

Before installing, operating or adjusting
this product, please read this instruction
booklet carefully and completely.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This lightning flash with arrowhead symbol
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
dangerous voltage within the product’s enclo­sure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.

The exclamation point within an equilateral tri­angle is intended to alert the user to the pres­ence of important operating and maintenance
(servicing) instructions in the literature accom­panying the product.

FCC WARNING: This equipment may generate or
use radio frequency energy. Changes or modifications
to this equipment may cause harmful interference
unless the modifications are expressly approved in the

2

instruction manual. The user could lose the authority
to operate this equipment if an unauthorized change or
modification is made.

REGULATORY INFORMATION: FCC Part 15

This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interfer­ence when the equipment is operated in a commercial
environment.
This equipment generates, uses, and can radi­ate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may
cause harmful interference to radio communications.
Operation of this equipment in a residential area is
likely to cause harmful interference in which case the
user will be required to correct the interference at his
own expense.

• A suitable conduit entries, knock-outs or glands
shall be provided in the cable entries of this
product in the end user.

• Caution: Danger of explosion if battery is
incorrectly replaced. Replaced only with the same
or equivalent type recommended by the
manufacturer. Dispose of used batteries according
to the manufacturer’s instructions.

• Holes in metal, through which insulated wires pass,
shall have smooth well rounded surfaces or shall
be provided with brushings.

Warning: Do not install this equipment in a confined
space such as a bookcase or similar unit.

Warning: Wiring methods shall be in accordance with
the National Electric Code, ANSI/NFPA 70.
Warning: This is a class A product. In a domestic envi­ronment this product may cause radio interference in
which case the user may be required to take adequate
measures.
Warning: To reduce a risk of fire or electric shock, do
not expose this product to rain or moisture.
Caution: This installation should be made by a
qualified service person and should conform to all local
codes.
Caution: To avoid electrical shock, do not open the
cabinet. Refer servicing to qualified personnel only.
Caution: The apparatus shall not be exposed to water
(dripping or splashing) and no objects filled with liquids,
such as vases, shall be placed on the apparatus.

To disconnect power from the mains, pull out the
mains cord plug. When install the product, ensure
that the plug is easily accessible.

Disposal of your old appliance

1. When this crossed-out wheeled bin symbol is
attached to a product it means the product is
covered by the European Directive 2002/96/
EC.

2. All electrical and electronic products should
be disposed of separately from the municipal
waste stream via designated collection facili­ties appointed by the government or the local
authorities.

3. The correct disposal of your old appliance will
help prevent potential negative consequences
for the environment and human health.

4. For more detailed information about disposal
of your old appliance, please contact your
city office, waste disposal service or the shop
where you purchased the product.

This product is manufactured to comply
with EMC Directive 2004/108/EC and Low
Voltage Directive 2006/95/EC.
European representative :

LG Electronics Service Europe B.V.
Veluwezoom 15, 1327 AE Almere,
The Netherlands (Tel : [phone])

3

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install
in accordance with the manufacturer's instruc­tions.

8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other appa­ratus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polar
ized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A
grounding type plug has two blades and a third
grounding prong. The wide blade or the third
prong are provided for your safety. If the pro­vided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete
outlet.

10. Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.

4

-

11. Only use attachments/accessories specified by
the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.

13. Unplug this apparatus during lightning storms
or when unused for long periods of time.

14. Refer all servicing to qualified service person
nel. Servicing is required when the apparatus
has been damaged in any way, such as power­supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or mois­ture, does not operate normally, or has been
dropped.

-

Contents

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Privacy Mask setting . . . . . . . . . . . . . . . . . . .30

Cautions for Safe Operation. . . . . . . . . . . . . . .7

Part Names and Functions. . . . . . . . . . . . . . . .8

Connections . . . . . . . . . . . . . . . . . . . . . . . . . .11

Installation of Camera . . . . . . . . . . . . . . . . . .15

Menu Operation . . . . . . . . . . . . . . . . . . . . . . .16

Focus settings . . . . . . . . . . . . . . . . . . . . . . . .19

Exposure settings. . . . . . . . . . . . . . . . . . . . . .22

White Balance setting. . . . . . . . . . . . . . . . . . .26

Day/Night setting . . . . . . . . . . . . . . . . . . . . . .28

Motion Detection setting. . . . . . . . . . . . . . . . .29

3D-DNR setting

Special menu settings . . . . . . . . . . . . . . . . . .33

Reset settings. . . . . . . . . . . . . . . . . . . . . . . . .39

On Screen Display . . . . . . . . . . . . . . . . . . . . .40

RS-485 Protocol . . . . . . . . . . . . . . . . . . . . . . .43

Specification . . . . . . . . . . . . . . . . . . . . . . . . . .45

. . . . . . . . . . . . . . . . . . . . . . .32

5

Features

This color video camera is designed for use in monitoring system.

High resolution and high sensitivity with a 1/ 4 inch EX-View CCD (Charge Coupled Device).

•

•

High magnitude of zoom lens with optical x27, Digital x12 (MAX x324)

Auto Focus

•

Auto White Balance

•

Auto exposure with DC Iris control

•

Day & Night function

•

WDR(Wide Dynamic Range) is available

•

Features Chart

This table shows the differences between the models.

Use LC703 is used for the description, operations and details provided in this operating guide.

Models Resolution Sens-Up WDR Day & Night Communication HSBLC
LC703P
LC703N
LC702P
LC702N
LC701P High Yes No Yes RS-485 Yes
LC701N High Yes No Yes RS-485 Yes

6

High Yes Yes Yes RS-485 Yes
High Yes Yes Yes RS-485 Yes
High No Yes Yes RS-485 No
High No Yes Yes RS-485 No

Cautions for Safe Operation

Power Supply

This camera must be operated DC 12V Certified/Listed,
class 2 power supply only.

Handling of the unit

Be careful not to spill water or other liquids on the unit.
Be cautions not to get combustible or metallic material
inside the body. If used with foreign matter inside, the
camera is liable to fail or to get cause of fire or electric
shock.

• Remove dust or dirt on the surface of the lens with a
blower.

• Use a dry soft cloth to clean the body. If it is very
dirty,use a cloth dampened with a small quantity of
neutral detergent,then wipe dry.

• Avoid the use of volatile solvents such as thinners,al
cohol,benzene,and insecticides.
They may damage the surface finish and/or impair
the operation of the camera.

Operating and storage location

Avoid viewing a very bright object (such as light fittings)
during an extended period. Avoid operating or storing
the unit in the following locations.

• Extremely hot or cold places (operating temperature

-10 °C - 50 °C, however, we recommend that the unit
be used within a temperature range of 0 °C - 45 °C)

• Damp or dust place

• Places exposed to rain

• Places subject to strong vibration
Close to generators of powerful electromagnetic radia-

•
tion such as radio or TV transmitters.

7

Part Names and Functions

 a

 b

8

a Lens mount cap

The cap is installed to protect the lens
mount section. Remove the lens mount cap
before install the camera. (sold separately) .

b Camera installation bracket

The bracket can be fixed at the top or bot­tom of the camera.

Part Names and Functions

 c d e

c Power indicator

Comes on when the power to the camera is on.

d Control buttons

T(TELE) button

•
When push, picture is telephoto.

N(NEAR) button

•
In a manual situation, focus get near.

M(MENU) button.

•
If you want to set up a diverse function, you
can push this button.

W(WIDE) button

•
When push, picture is wide angle.

F(FAR) button

•
In a manual situation, focus get far.

H(HOT) button

•
When you set the DAY/NIGHT mode to EXT,
you can change the Day/Night mode using
this button.

e Video output connector (BNC type)

Connect this connector to a device such as a VCR
or monitor with a VIDEO IN connector.

9

Part Names and Functions

f g

f Power input terminal

Connect to an external power supply of DC 12V.

10

g External Device Connectors

TRX -/+

•
Connect to an external controller of RS-485
format.

GND

•
Common GND.

Alarm Output Terminal (ALARM)

•
Connect to the alarm input of an external
device.

COM (Common)

•

OSD/D&N

•

OSD: Connect the external controller to

-

control the OSD function manually.

D&N: Connect the external controller to set

-

the D&N function manually. If you use the
external D&N function, you should set the
DAY/NIGHT option to EXT on the camera
setup menu.

FOCUS/ZOOM

•
Connect the external controller to control the
Focus and Zoom function manually.

Connections

Power connection

1. Remove the insulation on the power cable as illus­trated.

2. Attach the terminal tips.

3. Connect to the 12V DC UL Listed, Class 2 Power
Supply only on the camera.

Connecting Monitor

The video signal connection between the camera and
the monitor or DVR.

11

5~7 mm

TRX -

TRX +

Connections

Connecting RS-485 Controller

Connect to an external controller of RS-485 format.

RS-485
Controller

Alarm Connection

Connect an external device such as a buzzer or lamp
to the ALARM terminal. When the camera detects
motion, the alarm output signal is supplied to the con­nected external device.

Contact Ratings

• Maximum load current is ±130mA.

• Do not connect any system or device that has over
40 Vp-p (DC 30 V) bias voltage on the contact ter
minal.

Note:

Use a relay unit if the voltage or current of the con­nected device exceeds the ratings.

-

12

OSD (-5V ~ -12V)

COMMON

D&N (+5V ~ +12V)

COMMON

OSD (-5V ~ -12V)

COMMON

Connections

Day&Night function settings

If you set the DAY/NIGHT option to EXT on the
[CAMERA SET] menu, you can set the D&N function
manually.

In case that current D&N mode is set to Day mode

When you input the "+5V" signal to the OSD/D&N ter­minal and the COM is connected to grounds, the D&N
mode is set to Night mode.

In case that current D&N mode is set to Night mode

When you input the "+5V" signal to the OSD/D&N ter­minal and the COM is connected to ground, the D&N
mode is set to the Day mode.

OSD function settings

When you connect the "-5V" signal to the OSD/D&N
terminal, the menu is displayed or the sub menu is dis­played or the selected menu option is activated accord­ing to current conditions.

13

FOCUS (+: Near, -: Far)

COMMON

FOCUS (+: Near, -: Far)

COMMON

ZOOM (+: Tele, -: Wide)

COMMON

Connections

FOCUS and ZOOM Function Settings

You can set the FOCUS and ZOOM function manually.

Using the external controller or receiver unit to control
the FOCUS and ZOOM functions.

FOCUS function

ZOOM function

14

Installation of Camera

The bracket can be installed to either the top of the
camera as desired. When changing the position of the
camera mounting bracket, you should always reuse the
screws that have been removed.

Note:

If using a camera mounting bracket, select a location
that is strong enough to bear the full weight of the
camera and the mounting bracket for long periods, and
install the camera and mounting bracket securely.

15

Menu Operation

The following table shows the list of menu items and
options. You can adapt the camera to your require­ments by setting up the respective items in these
menus.

Main Menu Sub Menu Contents

FOCUS

EXPOSURE

16

FOCUS

MODE

FOCUS DIST 50CM, 1M, 3M, 5M

ZOOM START x1~x26

ZOOM END x2~x324

ZOOM

SPEED

ZTRK MODE AUTO/ MANUAL/ AUTO ONLY

INITIAL SET

WDR/BLC OFF/WDR/BLC/HSBLC

BRIGHT-

NESS

SHUTTER

SENS-UP OFF, AUTO x2 ~ AUTO x128

INITIAL SET

AUTO/ ONE PUSH/ ZOOM TRIG/
MANUAL

SLOW/ MIDDLE/ QUICK

EXIT RET/TOP/END

IRIS AUTO/MANUAL

AGC OFF/LOW/MIDDLE/HIGH

0~100

X512, ~, x2, AUTO, OFF, A.FLK,
1/160, ~, 1/90000

EXIT RET/TOP/END

Main Menu Sub Menu Contents

WHITE

BALANCE

DAY/NIGHT

ATW

AUTO

ONE PUSH

MANUAL

AUTO

DAY

NIGHT

EXT

COLOR TEMP

RED -100 ~ 100
BLUE -100 ~ 100
INITIAL SET
EXIT RET/TOP/END

D/N LEVEL

DWELL TIME

INITIAL SET
EXIT RET/TOP/END

INDOOR,
OUTDOOR

LOW/ MIDDLE/
HIGH
5, 10, 15, 30,
60 sec

Menu Operation

Main Menu Sub Menu Contents

MOTION DET

PRIVACY

MASK

OFF

ZONE
NUMBER
ZONE STATE OFF, ON
WIDTH
HEIGHT
MOVE X

ON

MOVE Y
SENSITIVITY
MOTION
ZOOM
INITIAL SET
EXIT RET/TOP/END

OFF

MASK
NUMBER
MASK STATE OFF, ON

MASK COLOR

WIDTH

ON

HEIGHT
MOVE X
MOVE Y
RESET MASK
INITIAL SET
EXIT RET/TOP/END

ZONE1 ~
ZONE4

OFF, X1~X27

MASK1 ~
MASK8

BLACK, GRAY,
WHITE

Main Menu Sub Menu Contents

3D-DNR

SPECIAL

RESET

EXIT

OFF

LOW

MIDDLE

HIGH

CAMERA ID 0~255

D-EFFECT OFF/ V-FLIP/ MIRROR/ ROTATE

COLOR

FREEZE OFF/ ON

SHARPNESS 0~68

STABILIZER OFF/ ON

OSD

LANGUAGE

INITIAL SET

EXIT RET/TOP/END

FACTORY

RESET

S/W VERSION

REBOOT

PROTOCOL LG/PELCO-D/PELCO-P

EXIT RET/TOP/END

OFF
ON COLOR LEVEL

OFF
USER TITLE
ZOOM MAG

ON

FUNCTION

ENG (The supported language can be
different depending on the model.)

CAMERA ID

17

Menu Operation

General Operation

1. Press [M] button on the rear of the camera.

The setup menu screen appears on the monitor.

2. Use [T] or [W] button to select an option then
press [M] button on the rear of the camera.
Submenu appears on the monitor.

[T] or [W] button to select a submenu option.

3. Use

[N] or [F] button to select a value.

4. Use

5. Select [EXIT] option then press
setup menu. In the submenu, use [T] or [W] but­ton to select the [EXIT] then use [N] or [F] button
to select a mode and press [M] to exit the setup
menu.

18

[M] to exit the

RET: Return to the previous.

•
TOP: Return to the CAMERA SETTING menu

•
screen.
END: Exit the setup menu.

•

Notes:

[T] button: Use to move upper direction on the

•

menu screen.

[W] button: Use to move lower direction on the

•

menu screen.

[N] button: Use for increase the value of the

•

option.

[F] button: Use for decrease the value of the

•

option.

[M] button: Executes selections and displays a

•

submenu for an item with the mark.

Focus settings

Focus Mode setting

Automatically and then the focus mode is automati­cally changed to manual mode.

MANUAL: Focus is activated only when the N

•
(NEAR) or F (FAR) keys on the camera is pressed.

Focus Distance setting

The camera adjusts the focus automatically by sensing
the center of the picture.
Select [FOCUS MODE] option on the [FOCUS] menu,
then select the following mode.

AUTO: Auto-focus is activated automatically.

•

ONE PUSH: The focus is activated manually. If

•
the camera is received auto-focus command, the
camera is activated Auto-focus mode and the focus
is set automatically and then the focus mode is
automatically changed to manual mode.

ZOOM TRIG: The focus is activated manually.

•
If you change the zoom, the focus is activated

Selects the minimum shooting distance for the focus.
Select [FOCUS DISTANCE] option on the [FOCUS]
menu, then select a focus distance value (50CM, 1M,
3M, 5M).

19

Focus settings

Zoom Start setting

Zoom End setting

You can set the zoom start position of the camera.
When the zoom function is operated, the zoom always
will start at the selected zoom start position.
Select [ZOOM START] option on the [FOCUS] menu,
then set a zoom start position (x1 - x26).

20

You can set the zoom end position of the camera. If
you set the zoom end position, the zoom is operated up
to the selected zoom end position.
Select [ZOOM END] option on the [FOCUS] menu, then
set the zoom end position ("Zoom Start position+1" ~
x324).

Focus settings

Zoom Speed setting

Zoom Tracking Mode setting

Selects a zoom speed.
Select [ZOOM SPEED] option on the [FOCUS] menu,
then select a zoom speed (SLOW, MIDDLE or QUICK).

Selects a zoom tracking mode. Zoom tracking means
focused zooming state.
Select [ZTRK MODE] option on the [FOCUS] menu,
then select a zoom tracking mode (AUTO or MANUAL).
If the FOCUS MODE is set to [ATUO], the ZTRK
MODE is set to [AUTO ONLY] and you can not change
the ZTRK MODE.

21

Exposure settings

Iris setting

AGC (Automatic Gain Control) setting

If the images are too dark, change the maximum [AGC]
value to make the images lighter.

1. Select [AGC] option on the [EXPOSURE] menu.

Select the desired lens iris value for camera exposure.
Select [IRIS] option on the [EXPOSURE] menu, then
select a value. (AUTO or MANUAL).

AUTO: The lens iris is set automatically.

•

MANUAL: Use [N] or [F] button to select the DC

•
Iris level.

22

2. Use [N] or [F] button to select a mode.

(OFFy LOWyMIDDLEyHIGH)

Exposure settings

WDR/BLC setting

Use WDR/BLC option to set the options for BLC or
WDR camera.

1. Select [WDR/BLC] option on the [EXPOSURE]
menu.

2. Use [N] or [F] button to select a mode then press
[M].

WDR: Set the WDR limit.

•

WDR LEVEL: LOW y MIDDLE y HIGH

-

BLC: Set the BLC limit.

•

BLC LEVEL: LOW y MIDDLE y HIGH

-

HSBLC: Use for adjusting brightness the

•
specific area of picture. The HSBLC mode is
automatically activated only in low illuminance
scene.

AREA SETTING: Use [N] or [F] button to

-

select a area then use [T] or [W] button to
select a ON or OFF. Press [M] to exit the
area setting menu.

GRAY SCALE: Use [N] or [F] button to

-

select a gray scale.
(GRAYyD.GRAYyBLACK).

HS LEVEL: Use [N] or [F] button to select a

-

bright level. (5 level)

MASK STATE: Use [N] or [F] button to

-

select [ON] or [OFF].
If you set the MASK STATE to ON, the
mask function is activate only when the
HSBLC is activated by auto mode.

OFF: Not used.

•

23

Exposure settings

BRIGHTNESS setting

You can increase the brightness of the darkened video.
If you set the brightness to lower value, the image is
darkened. If you set the brightness to higher value, the
image gets bright.

1. Select [BRIGHTNESS] option on the [EXPOSURE]
menu.

SHUTTER (Shutter Speed) setting

Select the desired shutter speed for camera exposure.
You can change the shutter speed to higher speed
to capture fast-moving subjects, though the image
becomes darker.

1. Select [SHUTTER] option on the [EXPOSURE]
menu.

2. Use [N] or [F] button to set the bright level.

24

2. Use [N] or [F] button to set shutter speed.
(x512~x2

1/160 ~ 1/90000)

y AUTOy OFF y A.FLK y

Exposure settings

SENS-UP setting

If pictures are not clear due to darkness, use for
increase the sensitivity of picture.

1. Select [SENS-UP] option on the [EXPOSURE]
menu.

2. Use [N] or [F] button to set the SENS-UP limit
(OFF, AUTO x2 ~ AUTO x128).
To setting the SENS-UP function, select the
[AUTO] on the [SHUTTER].

Note:

If you set to one of the SHUTTER options except AUTO
on the [SHUTTER] menu, the [SENS-UP] setting is not
available and [---] mark is displayed.

25

White Balance setting

Select the method by which the camera shifts its output
colors to compensate for the color of a light source.

1. Select [WHITE BALANCE] option on the [CAMERA
SET] menu.

2. Use [N] or [F] button to select a mode then press
[M].

ATW (Auto-Tracing White Balance): In this

•

mode, the color temperature range for the
proper white balance is approximately 1,800

- 10,500°K. Proper white balance may not be
obtained under the following conditions:

When the color temperature is out of the

­1,800 - 10,500°K range.

26

When the scene contains mostly high color

­temperature objects, such as a blue sky or
sunset.

When the scene is dim.

-

AUTO: In this mode, the color temperature

•
range for the proper white balance is approxi­mately 2,700 - 5,400°K. Proper white balance
may not be obtained under the following
conditions:

When the color temperature is out of the

-

2,700 - 5,400°K range.

When the scene contains mostly high color

-

temperature objects, such as a blue sky or
sunset.

When the scene is dim.

-

ONE PUSH: If you select the ONE PUSH

•
mode, you will be able to set up the White
Balance automatically using [M] button.

White Balance setting

MANUAL: You can set the white balance

•
options manually.

COLOR TEMP: Use [N] or [F] button to

-

select a function.

INDOOR: The color temperature

>

range for the proper white balance is
approximately 3,200°K.

OUTDOOR: The color temperature

>

range for the proper white balance is
approximately 5,100°K.

RED: Set the desired red value. (-100~100)

-

BLUE: Set the desired blue value.

-

(-100~100)

27

Day/Night setting

1. Select [DAY/NIGHT] option on the [CAMERA SET]
menu.

2. Use [N] or [F] button to select mode for day/night
function.

• AUTO: You will be able to change the Day/

Night mode automatically.

Note:

If you set the AGC to [OFF] or the SHUTTER
is set to one of the SHUTTER options except
AUTO on the [EXPOSURE] menu, the AUTO
mode of the DAY/NIGHT function is not avail­able and [---] mark is displayed.

28

D/N LEVEL: Use [N] or [F] button to select

­a level.

(LOWyMIDDLEyHIGH)

DWELL TIME: Use [N] or [F] button to

­select a dwell time. (5, 10, 15, 30 or 60
sec.)

• DAY: Color mode enabled.

• NIGHT: Black-and-white mode enabled.

• EXT : Switches between color picture and
black-and-white picture when an external day/
night switching signal is received.

Motion Detection setting

The motion detection detects the moving objects in the
scene by monitoring changes in brightness level. You
can select the level of sensitivity for motion detection
to 4 zone.

1. Select [MOTION DET] option on the [CAMERA
SET] menu.

[N] or [F] button to select a [ON] and press

2. Use
[M]. The MOTION DETECTION menu appears.

3. Use [N] or [F] button to select a zone number
(ZONE1 ~ ZONE4) on the [ZONE NUMBER]
option.

[N] or [F] button to set up the ON or OFF on

4. Use
the [ZONE STATE] option. If you set to ON, the
zone frame appears on the center of the monitor.

5. Use

[T] or [W] to select an option then use [N] or

[F] button to adjust the option

WIDTH: Enlarge or decrease the horizontal

•
size of the zone frame.

HEIGHT: Enlarge or decrease the vertical size

•
of the zone frame.

MOVE X: Moves horizontal position of the

•
zone frame.

MOVE Y: Moves vertical position of the zone

•
frame.

6. Use [SENSITIVITY] option to obtain the optimum
detection level.

7. Select the motion zoom level. If you set the motion
zoom, the camera is activated according to the
selected motion zoom level and after some time
passes, it returns to the previous zoom level when
the motion is detected.

29

Privacy Mask setting

This function is aiming at the protection of personal pri­vacy, selecting a screen part black not to be displayed
in the screen. Up to 8 zones can be registered.

1. Select [PRIVACY MASK] option on the [CAMERA
SET] menu.

[N] or [F] button to select a [ON] and press

2. Use
[M]. The PRIVACY MASK menu appears.

3. Use [N] or [F] button to select a zone number
(MASK1 ~ MASK8) on the [MASK NUMBER]
option.

[N] or [F] button to set up the ON or OFF on

4. Use
the [MASK STATE] option. If you already registered
the mask zone and set to ON, the mask zone box
appears on the monitor.

30

5. Select [RESET MASK] and press
ter the mask zone for the first time, the mask zone
box appears on the center of the monitor. If you
already registered mask zone, it will be returned
to its initial state and appear on the center of the
monitor.

[N] or [F] button to select the color of the

6. Use
mask zone box on the [MASK COLOR] option.

[T] or [W] to select an option then use [N] or

7. Use
[F] button to adjust the option

WIDTH: Enlarge or decrease the horizontal

•

size of the mask zone box.

HEIGHT: Enlarge or decrease the vertical size

•

of the mask zone box.

MOVE X: Moves horizontal position of the

•

mask zone box.

MOVE Y: Moves vertical position of the mask

•

zone box.

Notes:

If you want to reset the mask zone position, select

•
RESET MASK option and press [M] button.

[M]. If you regis-

Privacy Mask setting

The parts with the registered mask numbers from

•
MASK1 to MASK4 have the same color. (So do the
parts with the numbers from MASK5 to MASK8).
If you change the mask color, the registered mask
color will be changed automatically with the same
color for each of group (MASK1~4, MASK5~8).

31

3D-DNR setting

1. Select [3D-DNR] option.
If pictures are not clear due to brightness, use for
reduce the noise of picture.

[N] or [F] button to select a option.

2. Use
(OFFyLOWyMIDDLEyHIGH)

Notes:

• If you set the AGC to [OFF] on the [EXPOSURE]
menu, the [3D-DNR] function is not available.

• When you use this function, the afterimage may
occur.

32

Special menu settings

Camera Identification setting

You can use the camera identification (CAMERA ID) to
assign a number to the camera.

1. Select [CAMERA ID] option on the [SPECIAL]
menu.

D-EFFECT (Digital effect) setting

You can select the digital effect.

1. Select [D-EFFECT] option on the [SPECIAL] menu.

2. Use [N] or [F] to select a CAMERA ID (0~255).

2. Use [N] or [F] button to select a digital effect.

• V-FLIP: Flip the picture vertically.

• MIRROR: Turn on the mirror effect.

• ROTATE: Rotate the picture. (180°)

• OFF: Turn off the digital effect.

33

Special menu settings

Color setting

You can switch the displayed picture to grayscale or
color.

1. Select [COLOR] option on the [SPECIAL] menu.

2. Use [N] or [F] button to change a color effect.

• ON: To display the picture with color.

Select ON and Press

menu.
You can adjust the color level using the [N] or
[F] button.

• OFF: To display the picture with grayscale.

34

[M] to display the sub-

Freeze setting

1. Select [FREEZE] option on the [SPECIAL] menu.

2. Use [N] or [F] button to set up the ON or OFF.

Special menu settings

Sharpness setting

Sharpens the image outline.

1. Select [SHARPNESS] option on the [SPECIAL]
menu.

2. Use [N] or [F] button to change a adjust the option.
If you set the sharpness value to higher, the image
outline becomes sharp. If you set to lower value,
the image outline becomes dim.

Stabilizer setting

The image stabilizer function minimizes the appearance
of shaky images caused by low-frequency vibration.

This function is useful for outdoor surveillance.

Select [STABILIZER] option and set to ON or OFF.

Note:
If you set the [STABILIZER] to ON, the Digital zoom is
set to [x1.1] automatically.

35

Special menu settings

OSD setting

You can set the Function On-Screen Display options
using the [OSD] menu.
The Function On-Screen Display of this camera can be
turned on or off.

1. Select [OSD] option on the [SPECIAL] menu.

[N] or [F] button to select a [ON] and press

2. Use
[M]. The OSD menu appears.

36

3. Use [T] or [W] to select an option then use [N] or
[F] button to set the option.

• ON: Displays the Function OSD on the screen.

• OFF: The Function OSD does not appear on

the screen.

Special menu settings

User title setting

You can use the camera identification to assign a num­ber and character to the camera (0 - 9, A-Z, a-z).
The USER TITLE is displayed on the upper left of the
screen.
To disappear the user title, select [OFF].

1. Select [USER TITLE] option on the [SPECIAL]
screen.

[N] or [F] button to select a [ON] then press

2. Use
[M]. The USER TITLE menu appears.

A

- CLR: If you enter the wrong code, select CLR

then press [M].

- POS: Use
USER TITLE on the screen.

- END: Confirm your selection.
A(Blank): Insert a space at the cursor posi-

-
tion.

-

[N] or [F] button to move position of

/ : Moves cursor to left or right.

3. Use [T], [W], [N] or [F] button to select a character

or number.

37

Special menu settings

Language setting

Select a language for setup menu and information
display.

38

Reset settings

1. Select [RESET] option.

2. Press

[M] button and the RESET menu appears.

3. Use [T] or [W] to select option.

• FACTORY RESET: Clear certain settings and
information and return to factory default set­tings.

• S/W VERSION: Displays the software version
on the monitor.

• REBOOT: Reboot the camera system.

• PROTOCOL: Select the protocol for the cam
era communication among the LG, PELCO-D
and PELCO-P.

4. Press

[M] to confirm your selection.

-

39

On Screen Display

X20

35

TITLE1

X20

35

TITLE1

X20

35

TITLE1

X20

35

TITLE1

X20

35

TITLE1

X20

TITLE1

X20

TITLE1

Some of these functions will be displayed every
time the camera is operated.

abcdefg h ijkl

Function

a

b

c

Focus
Mode

Camera
ID

Manual
Focus
Action

OSD

Format

None Display Zoom Trigger Mode

0~255

Description

Auto Mode

Manual Mode

One Push Mode

Displays when the
Auto focus is operat­ing.

Displays the camera
ID.

Focus Near

Focus Far

m n o

40

X20

TITLE1

X20

TITLE1

X20

TITLE1

X20

TITLE1

X20

TITLE1

X20

TITLE1

X20

TITLE1

X20

X20

X20

X20

X20

On Screen Display

Function

d

e

f

White
Balance
Mode

White
Balance
Manual
Mode

Backlight
Compen­sation
Mode

OSD

Format

None Display Auto or ATW Mode

None Display

Description

Manual Mode

One Push Mode

Indoor

Outdoor

Backlight Compen­sation is turned off.

WDR On

BLC On

HSBLC On

Function

g

h

i

j

3D-DNR

User Title

Day &
Night
Mode

D-Effect
Status

OSD

Format

None Display

Text: A~Z,
0~9, ‘-’, ‘.’, ‘ ‘

None Display Day Mode

None Display D-Effect Off

Description

3D-DNR is turned
off.

3D-DNR is turned
on.

User Title

Night Mode

V-Flip

Mirror

Rotate

41

X20

X20

X20

X20

On Screen Display

Function

k

l

m

n

o

42

Color
On/Off
Status

Freeze
On/Off
Status

Preset
Status

Motion
Detection
Status

Zoom
Display

OSD

Format

None Display Color On

None Display Freeze Off

+ Number

X1~X324

Description

Color Off

Freeze On

Displays when "Set
preset" or "Go to
preset" function is
operating.

Displays when the
motion is detected.

Optical Zoom: 27X,
Digital Zoom: 12X

RS-485 Protocol

Data Communication Format

• Data Length: 1 Byte (8 Bit)

• Start/Stop Bit: 1 Bit

• Parity Bit: None

• Baud rate: 9,600 bps

Format

Byte 1 Byte 2 Byte 3 Byte 4 Byte 5 Byte 6 Byte 7

0xE5 0x87 Camera ID 0x60 Key In or Key Out Key Code *C.S.

*C.S. = Check Sum

• The data of total 7 bytes is transmitted from the external RS-485 device to the camera.

• Byte 7 : The value of Check Sum from ‘Byte 1 ’ to ‘Byte 6 ’.

43

RS-485 Protocol

Commands

Function Command Description

Menu

Tele (Menu Up)

Wide (Menu Down)

Near (Menu Right)

Far (Menu Left)

Note:

You must enter the Key out command after the Key input commend.

Key In E5 87 ID 60 00 14 CS

Key Out E5 87 ID 60 FF 14 CS

Key In E5 87 ID 60 00 08 CS

Key Out E5 87 ID 60 FF 08 CS

Key In E5 87 ID 60 00 04 CS

Key Out E5 87 ID 60 FF 04 CS

Key In E5 87 ID 60 00 02 CS

Key Out E5 87 ID 60 FF 02 CS

Key In E5 87 ID 60 00 01 CS

Key Out E5 87 ID 60 FF 01 CS

44

1) OSD On Key Action

2) When OSD is being displayed, Enter into
the submenu or execute the menu item.

1) Menu Defined Speed Tele Key Action

2) When OSD is being displayed, select
upper menu item.

1) Menu Defined Speed Wide Key Action

2) When OSD is being displayed, select
lower menu item.

1) Menu Defined Speed Near Key Action

2) When OSD is being displayed, select
option item in the right side.

1) Menu Defined Speed Far Key Action

2) When OSD is being displayed, select
option item in the left side.

Specification

Model LC701N LC702N LC703N LC701P LC702P LC703P

Signal System NTSC PAL

Total Pixels No. 811(H) X 508(V) 795(H) X 596(V)

Image Device 1/4" EX-View CCD

Lens

IRIS Control DC IRIS

Sync. System Internal

Scanning Frequency (H) 15.734 KHz 15.625 KHz

Scanning Frequency (V) 59.94 Hz 50 Hz

Horizontal Resolution More than 540 TV Lines

S/N Ratio More Than 50dB (AGC Off)

Minimum

Illumination

Video Output Signal 1Vp-p Composite (75Ω)

Color Mode

B/W Mode

0.003 (0.6) Lux
(Sens-up OFF)

0.0001 (0.1) Lux
(Sens-up OFF)

x27 Zoom ( F1.5(Wide End) , F3.6(Tele End)

( f = 3.25mm ~ 88 mm )

0.6 Lux

0.1 Lux

0.003 (0.6) Lux
(Sens-up OFF)

0.0001 (0.1)
Lux

(Sens-up OFF)

0.003 (0.6) Lux
(Sens-up OFF)

0.0001 (0.1) Lux
(Sens-up OFF)

0.6 Lux

0.1 Lux

0.003 (0.6) Lux
(Sens-up OFF)

0.0001 (0.1) Lux
(Sens-up OFF)

45

Specification

Model LC701N LC702N LC703N LC701P LC702P LC703P

Control Method RS485

Auto Gain Control Off / Low / Medium / High

Day & Night Day / Night / Auto / Ext

Electronic Shutter 1/60 ~1/90,000 1/50 ~1/90,000

White Balance Auto / ATW/ ONE PUSH / Manual

Electronic Sensitivity OFF /Auto

WDR (BLC)

Motion Detection On / Off

Privacy Zone Masking 8 Zones

Power Source DC12V ± 20%

Power Consumption 3.6 W

Operation Temp. / Humidity -10 ºC ~ 50 ºC / 0%RH ~ 80%RH

Storage Temp. / Humidity -20 ºC ~ 60 ºC / 0%RH ~ 85%RH

Weight 520 g

Dimension (H x V x D) 64 X 78.6 X 118.2mm

OFF / BLC /

HSBLC

46

OFF/WDR /

BLC

OFF/WDR /

BLC / HSBLC

OFF / BLC /

HSBLC

OFF/WDR /

BLC

OFF/WDR /

BLC / HSBLC

P/NO : MFL62723722