Ganz GLFE4EOU, GLFE1EOU, GLFE16EOC, GKFE1EOU, GKFE1EOC Specsheet

Ethernet-over-Copper Extender With Pass-Through PoE

GLFE(X)EO(C,U)

HARDENED

The Ganz™ Ethernet over copper line supports up to sixteen channels of
10/100Mbps Ethernet with Pass-through PoE over twisted pair cable (CAT-5,
UTP), or over coaxial cable. The single channel units may be powered by a
PoE switch or the included power supply. Four, eight, and sixteen channel units
operate from local power. These units provide the ultimate flexibility for extending
a powered device (PD) over long distance copper. DIP switches are provided
for user-selection of local or remote, 10 or 100Mbps, and 1 pair or 4 pair (UTP)
settings.

EXTENDER PASS-T HRU

FEATURES

› Transmits individual Ethernet data channels with Pass-through

PoE over standard UTP or Coaxial cable

› Extends Ethernet up to 3,000 feet (914 m) at 10 Mbps or

2,000 feet (610 m) at 100 Mbps over UTP cable

› Extends Ethernet up to 5,000 feet (1,524 m) at 10 Mbps or

2,000 feet (610m) at 100 Mbps over Coaxial cable

› Extended temperature operation from -40°C to +75°C

› Extended Pass-through PoE meets the IEEE 802.3af standard

for Power over Ethernet

› Full 10/100 Mbps Bandwidth

› Supports Multicast, Unicast and Jumbo Frame

› Symmetric Bandwidth provides consistent upload and download

with virtually zero packet loss over the total usable distance

› Type tested to RFC-2544 TCP/IP network bandwidth packet

transmission standards

› User-selectable data rate for maximum bandwidth and

transmission distance utilization

› Complies with all major IEEE standards and RFC network

protocols for UDP, TCP/IP, HTTP/HTTPs

› Tested and certified* by an independent laboratory for full

compliance with the environmental requirements (ambient
operating temperature, mechanical shock, vibration, humidity
with condensation, high-line/low-line voltage conditions
and transient voltage protection) of NEMA TS-1/TS-2 and
CALTRANS Traffic Signal Control Equipment Specifications.

› Designed and manufactured in the USA

› LED status indicators confirm operating status

› Available in small-size, interchangeable stand alone, or 1RU

high rack mounted models

› Lifetime warranty

APPLICATIONS

› Retrofit existing analog CCTV installations to Ethernet-

based systems

› CCTV systems for casinos, airports, school campuses

* One Channel Units Only. Multichannel units are designed to meet NEMA TS-2 Spec.

GLFE(X)EO(C,U)

SPECIFICATIONS

Ethernet-over-Copper Extender With Pass-Through PoE

Ethernet

Data Rate DIP-switch selectable 10/100Mbps

RFC 2544 TCP/IP Packet Transmission
Standards IEEE 802.3af PoE,

Transmission Distances

Data Interface 10/100BaseT(X) Ethernet

Full data rate / full duplex up to the maximum rated
distance

RFC: 768 UDP, 2068 HTTP, 793 TCP
791 IP, 1783 TFTP, 894 IP over Ethernet.

1

See chart below

Connectors

Ethernet RJ-45
Extended Distance Coaxial (C): female BNC

Ethernet (U): RJ -45

Operating Power Powered by PoE or 2-pin screw terminal for

local power

LED Indicators Operating Power

Ethernet Link and Activity
Extended Link and Activity

Power

Pass-Through Mode 1 CH: Operates on PoE power

or optional 9 to 36 VDC or 24 VAC, 1.5 W
4 CH: 9 to 15 VDC, 5W
16 CH: 9 to 15 VDC, 20W

Mechanical

Limiters
Circuit Board Meets IPC Standard
Size (L×W×H) 1 CH: 3.3 × 2.5 × 1.1 in (8.4 × 6.4 × 2.8 cm)

Number of Rack Slots 1 (4CH Version Only)
Shipping Weight 1 CH: <1 lbs./0.5 kg

Current Protection Automatic Resettable Solid-State Current

4 CH: 6.1 × 5.3 × 1.1 in (15.5 × 13.5 × 2.8 cm)
16 CH: 6.1 × 19 × 1.75 in (15.5 × 48.26 × 4.45 cm)

4 CH: <2 lbs./0.9 kg
16 CH: <5 lbs./2.3 kg

Environmental

MTBF >100,000 hours
Operating Temp – 40˚ C to +75˚ C

UL Safety certifications conducted at maximum
ambient temperatures (Tma) of 65ºC.

Storage Temp – 40˚ C to +80˚ C
Relative Humidity 0% to 95% (non-condensing)

[1] Distance figures are based on a 50 V PSE PoE power source, and external power

supplies for the extenders. Distance figures are obtained using in-house testing
mirroring installations. Factors such as coaxial and copper cable quality, the number
of connectors and splices in the cable run, the use of PoE, and environmental
conditions encountered within the installation might affect the actual transmission
distance and should be taken into consideration. Due to advanced negotiation
signaling required in IEEE802.3at applications, pass-through applications are limited
to IEEE802.3af PD devices only. When using UTP models Pass-Through PoE is
only possible in 4-pair mode.

2

ORDERING INFORMATION

Part Number Description Position Channels Form Factor Cable

GLFE1EOC 1 Port Ethernet-over-Coax Extender Local/Remote Configurable 1 Small Size Coax

GLFE1EOU 1 Port Ethernet-over-UTP Extender Local/Remote Configurable 1 Small Size UTP

GLFE4EOC 4 Port Ethernet-over-Coax Extender Local/Remote Configurable 4 ComFit (1 Slot) Coax

GLFE4EOU 4 Port Ethernet-over-UTP Extender Local/Remote Configurable 4 ComFit (1 Slot) UTP

GLFE16EOC 16 Port Ethernet-over-Coax Extender Local 16 1 RU 19” Rack Mount Coax

GLFE16EOU 16 Port Ethernet-over-UTP Extender Local 16 1 RU 19” Rack Mount UTP

Accessories: Unit-appropriate power supply (one each provided with each extender unit)

Options [2] Add suffix ‘/C’ for Conformally Coated Circuit Boards to extend to condensation conditions (Extra charge, consult factory)

DIN-Rail Mounting Adaptor Kit - With Mounting Hardware (Optional, order model DINBKT1 or DINBKT4) (Suitable for 1CH and 4CH units only)