Ganz DAY/NIGHT VANDAL DOME CAMERA Instruction Manual

DAY/NIGHT VANDAL DOME CAMERA

About this manual

Dimensions : mm

■ CONNECTIONS

INSTRUCTION MANUAL

Before installing and using the camera, please read this manual

carefully. Be sure to keep it handy for later reference.

TROUBLESHOOTING

Before sending the camera out for repair, check the items below. If the problem persists after checking these items, contact your service center.

■ If no image appears

Is the coaxial cable attached securely? Are the power and voltage normal? Has the iris of the lens inside the camera been adjusted correctly (with the level volume) ? Is there adequate illumination?

■ If the image is unclear

Is the lens in focus? Is the lens dirty? Dirt of fingerprints on the lens can adversely affect the images. Gently wipe any dirt or fingerprints off the lens with a soft cloth or lens cleaning paper and cleaning fluid (commercially available). Is the monitor adjusted correctly?

WARNING:

TO PREVENT THE RISK OF FIRE OR

ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION :

Check for polarity when using a DC 12V or AC 24V power

CONNECTOR AND CAMERA SETTING

PRECAUTIONS

■ Do not open or modify Do not open the cabinet except during maintenance and installation, as it may be dangerous and cause damages.

■ Do not put objects inside the unit Make sure that no metal objects or flammable substances get inside the camera. It could cause fire, short-circuits or damages.

■ Be careful when handling the unit To prevent damage, do not drop the camera or subject it to strong shock or vibration.

■ Install away from electric or magnetic fields

■ Protect from humidity and dust

■ Protect from high temperature

Be careful when installing close to the ceiling , in a kitchen or boiler room, as the temperature may raise to high levels.

■ Cleaning

Dirt can be removed from the cabinet only by wiping it with a soft cloth moistened with a soft detergent solution.

■ Mounting Surface The mounting surface material must be strong enough to secure the camera.

MODEL General Spec NTSC PAL

CCD Type

1/3" 410K Pixels Color 1/3" 470k Pixels Color Total number of pixels 811(H) X 508 (V) 795(H) X 596(V) Min illumination Video Output Resolution S/N Ratio Shutter speed x128 : 1/60~1/120,000sec x128 : 1/50~1/120,000sec Sync System White Balance OSD

Built-in DAY / NIGHT

AUTO / B/W / COLOR DNR

LOW, MIDDLE, HIGHT,OFF

Power Input Video Output

Voltage Power Consumption

Lens Dimension Weight Case Color Operation temp In storage temp Operation humidity

-10℃ ∼ +55

℃

-20℃ ∼ +70

℃

Under 90％ (Non-condensing)

850g

Ivory

Max [DC12V : 5.7 W , AC24V : 5.3 W]

Mechanical Spec

3.3~12.0 mm

300(ø) X 267.6(H)mm

Wire

BNC Cable

Electric Spec

DC 12V(10 - 20V) or AC24V(20 - 28V)

50dB (AGC off, weight ON)

Internal / External

ATW/AWC/MANUAL (1800 ˚K ~ 10,500 ˚K)

Connector

VRD135-90-DNR-TDN3-AC3V

0.3 Lux/F1.2(50 IRE, AGC HIGH, DNR HIGH)

1.0Vp-p/75 ohm Composite

520 TV Lines(Min)

DC12V / AC24V

■ LENS ADJUSTMENTS

■ CAMERA SETTINGS

● OSD SWITCH FUNCTION

1. Adjust the panning(360˚) and tilt(70˚) position.

2. Setting the zoom position by using Zoom Lever Screw.

3. Setting the focus by using Focus Lever Screw.

CONNECTIONS AND CAMERA SETTINGS

SETUP FUNTION SUMMARY

when using BUILT-IN lens,

the type of the lens is able to fix

SHUTTER ESC, MANUAL, FLK MANUAL: 1/60(50) ~ 1/120,000sec

WHITE BAL. ATW, AWC, MANUAL

ATW: 1,800 ~10,500 ˚K

BACKLIGHT OFF, LOW, MIDDLE, HIGH Backlight compensation

AGC OFF, NORMAL, HIGH the Brightness can be adjusted(1 ~ 70)

DNR OFF, LOW, MIDDLE, HIGH

when AGC is turned off, DNR does not

when AGC is turned off, SENS-UP

does not operate.

SPECIAL Refer to the bottom

EXIT Saved all the setting menu, then exits.

SPECIAL FUNTION SUMMARY

uppercase or lowercase, maximum length for the name

/numeral 0~9/-, null display is limited 15letters.

AUTO : night time→ B/W mode

day time → color mode ,

B/W : Always B/W mode

COLOR : Always color mode

LL mode: you can adjust desired phase

from 0˚ ~ 359˚, auto detection

MATION ON mode: AREA(4 programmable zone)

DETECTION the word "MOTION DETECTED" appear

on the screen when movement is detected

ON mode:AREA(4 programmable zone ),

/SIZE/TONE

MIRROR OFF, ON set a horizontal image inversion.

SHARPNESS OFF, ON the available range of level is 0 ~ 31.

returns to the level which was set

by the manufacturer for shipment.

save the SPECIAL MENU and then

returns to the SETUP MENU

RESET

RERURN

OFF, ON PRIVACY

OFF, ON

CAMER ID

DAY / NIGHT

COLOR→AUTO→B/W

SYNC

INT, LL

SENS-UP

OFF, AUTO

LENS

MANUAL, DC