Page 1
INSTALLATION INSTRUCTIONS
Product Revision
7160-0581
Samsung Galaxy Tab Active Docking Station
Rev. A
Printing Spec:
Form
INST-682
PS-001
This instruction sheet is for the Samsung Galaxy Tab Active docking station only.
For instructions on features, set-up, and operation of the Galaxy Tab Active
tablet, please refer to the manual provided by Samsung with the tablet.
This docking station is designed to be used with a variety of Gamber-Johnson
mounting systems. Installation instructions for other Gamber-Johnson products
are provided with each individual product.
Product Mounting Disclaimer
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
© Copyright 2015 Gamber-Johnson, LLC
If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868
Page 2
PRE-INSTALLATION RECOMMENDATOINS
Conduct a "Bench Test"
Gamber-Johnson strongly advises a "bench test" be conducted to verify all
electronic and software issues are resolved prior to installation:
Make sure the computer is operational by itself.1.
Insert computer into the docking station and verify that the computer is 2.
operating in the dock and battery is charging.
Gamber-Johnson recommends positioning of all mounts and equipment in the
vehicle prior to the actual install to verify that mounting locations are safe and
practical.
IMPORTANT SAFETY INFORMATION FOR INSTALLERS
Safety is dependent on the proper installation and servicing of this docking station. It is
important to read and follow all instructions before installing this product.
To properly install a Gamber-Johnson docking station you must have a good understanding of
automotive electrical procedures and systems, along with proficiency in the installation and
service of aftermarket vehicle equipment.
There are no adjustments required at any time of the electrical components within the
docking station.
During Installation:
DO NOT connect this docking station to the vehicle battery until:
All other electrical connections are made1.
Mounting of all components is complete2.
Verification that no shorts exist in the entire system3.
DO NOT install equipment or route wiring or cords in the deployment path of any air bag.
When drilling into the vehicle, DO make sure that both sides of the surface are clear of
anything that could be damaged.
CAUTION:
sparks resulting in electrical fires or flying molten metal.
If wiring is shorted to the frame, high current conductors can cause hazardous
Opening the docking station will void the product warranty.
After installation:
Test the docking station to ensure that it is working properly.
File these instructions in a safe place and refer to them when performing maintenance or reinstalling.
WARNING
damage, serious injury, or death.
: Failure to follow all safety precautions and instructions may result in property
Page 3
WIRING INSTRUCTIONS
IMPORTANT: Make sure that you have read this entire section before you begin
wiring! Refer to Figure 1.
1. Install docking station into vehicle, making sure that all bolts are tight.
2. Connect BLACK ground wire to the location where the vehicle battery grounds
to vehicle chassis. Use a minimum of 16 AWG wire.
3. Connect RED power wire to the supply voltage (Battery, V+)through fuse from
the vehicle.
IMPORTANT REMINDERS:
Use only SAE J1128 Type GPT number 16 AWG stranded wire (minimum) to •
attach the docking station to the vehicle's electrical system.
Connect lead wires using appropriate wire connecting devices. Examples •
would be: Butt Splices, Quick Dissconects or Terminal Blocks.
Use Proper Crimp tools to make sure that correct crimp is applied properly to •
avoid wire from becoming disconnected and making sure good
connection.
Route the lead wires to the battery. Total wire in the circuit must not exceed •
30 feet and must conform to SAE standard J1128.
Protect the lead wires from abrasion and chafing by using wire loom or •
conduit, and route away from moving parts or areas where high
temperatures may occur.
The power connection must be made with a 5 amp in-line fuse.•
The fuse holder location must be kept within 10 inches of the connection to •
the battery positive, away from moving parts, and temperatures that
exceed 180 degrees F.
Caution: For continued protection against risk of fire replace only with the •
same type and rating of fuse.
If a timing device is used follow the instructions of the manufacturer of that •
device. It must be wired in-line with the supply voltage (V+) to the docking
station.
If you have any installation questions, please call Gamber-Johnson customer
•
support at 1-800-456-6868
Ground to Vehicle Chassis
+
-
Figure 1
Vehicle Battery
16 AWG (black wire) J1128 Type GPT
Fuse Holder
16 AWG (red wire) J1128 Type GPT
5 Amp Fuse
Connect to
Dock GND
Connect to
Dock PWR
Page 4
SAMSUNG GALAXY TAB ACTIVE
DOCKING STATION FEATURE IDENTIFICATON
Latch
Base
Docking Connector
POWER CABLE WITH A FUSED
(3A) CIGARETTE LIGHTER PLUG
Lock
4x 1/4-20unc threaded
inserts (Vesa 75mm
hole pattern)
2x #6-32unc theaded
inserts
Page 5
DOCKING AND UNDOCKING THE TABLET
1. Insert the bottom of the tablet into
the docking station.
Figure 1
Then rotate the top of the tablet under
the top latch until the tablet is resting
inside the main housing. The latch will
spring down in front of the tablet to
hold it in place.
(See figures 1, 2, & 3)
2. (Optional) The key lock can now
be used for security purposes.
Figure 2
Figure 3
TO UNDOCK THE COMPUTER
1. Unlock if locked.
2. Push upward on the thumb knob and
pull outward on the top of the tablet
until it clears the top latch. Lift the
tablet out of the dock.
(See figure 4)
Figure 4
Page 6
Regulatory Certification Information
Regulatory Model #: 7160-0581
GJ Model #'s: 7160-0777
Descriptions: Dock-Samsung-Galaxy Tab Active w/o Cigarette Lighter Plug
Certifications:
EN 55022:2010 CISPR 22:2008 Class B•
EN 50498:2010•
EN 50581:2012
•
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions. (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interfernece that may cause undesired operation.
Gamber-Johnson LLC, 3001 Borham Ave.,
Stevens Point, WI, 54481, USA, 715-344-3482
Loading...