Gamber Johnson MCS-EPIC9, MCS-EPIC17, MCS-EPIC13 User Manual

INSTALLATION INSTRUCTIONS

Product Revision Form #

9", 13" & 17" EPIC Console Boxes Rev. D INST-104

MC S -E PI C9, MC S - E PI C 13, M CS-E PI C 17

The MCS-EPIC9, MCS-EPIC13 or MCS-EPIC17 can be
installed on Gamber-Johnson MCS-Top Plates and on
top plates made by other mount manufacturers, or
may be bolted directly to the floor or transmission
hump of your vehicle. When bolting to the floor,
check under the vehicle to be sure you will not
damage the transmission housing or other
under-floor parts. Bolts for attaching the console to
the floor are not furnished with the mount.

.25-20
BUTTON HEAD
HARDWARE

CONSOLE
BOX

CONSOLE BASE

Installing MCS-EPIC9, MCS-EPIC13 or MCS-EPIC17 on

TOP PLATE

Gamber-Johnson MCS-Top Plate:

1. Place the MCS-Top Plate in the vehicle in the
approximate position it will occupy when it is installed.
Set the console on the top plate to determine the
desired position. Mark that position or make note of
which slots line up with the mounting holes in the

.25-20 CARRIAGE
BOLT HARDWARE

console base. Remove the console and top plate from
vehicle.

2. Insert (4) .25-20 x 1.00 carriage bolts, from the bottom side, through slots in the top plate and mounting
holes in console base. Add (4) flat washers, (4) lock washers and (4) .25-20 hex nuts from the top side.

3. Install console base and top plate into vehicle according to the instructions provided with the vehicle base.

4. Assemble faceplates to control heads as described in instruction sheet INST3.
Install the control heads, accessories and blank panels into the console box.

6. Electrically connect the equipment at this time. It is important to allow extra wire length for servicing the
equipment. Grommets are provided for lining knockout holes.

7. Slide the console box over the console base. The height and angle can be adjusted if needed by removing
the (4) .25-20 x .50 Button Head Screws from the sides of the console box, repositioning the slots on the
console box with the threaded inserts on the console base and reinstall the Button Head Screws.

Installing MCS-EPIC9, MCS-EPIC13 or MCS-EPIC17 on Top Plates by other manufacturers:

The slotted hole pattern in the base of the Epic Boxes lines up with the hole pattern in several top plates made
by other mount manufacturers.
Installation is similar to that listed above except for item #2.
Size and quantity hardware depends on top plate being used and must be supplied by customer.

Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.

© copyright 2012 Gamber-Johnson, LLC

If y ou need assistance or have questions, call Gambe r-Johnson at 1-800-456-6868

Sheet 1 of 2

Addition al MCS A c c e ss o r ie s

MCS-ARMREST MCS-CUP2

MCS-CUP2

7160-0110
(6 Circuit Power Strip)

MCS-CUPHOLD2

7160-0063
(Cigarette Lighter Adapter Kit)

3130-0361
(Knockout Filler Panel)

7160-0100
(L ED Light Assembly)

Sheet 2 of 2