Gamber Johnson 7160-1265-04, 7160-1265-02-E, 7160-1265-04-E, 7160-1265-00-E, 7160-1265-04-P Installation Instructions Manual

INSTALLATION INSTRUCTIONS

Product

7160-1265-xx (-P & -E)

Docking Station CF20

Revision

REV C

Printing Spec:

Form

INST-862

PS-001

This instruction sheet is for the CF20 docking station. For instruction on features, set­up and operation of CF20 computer, please refer to the manual provided by Panasonic
with the computer.

This docking station is designed to be used with a variety of Gamber-Johnson
mounting systems. Installation instructions for other Gamber-Johnson products are
provided with each individual product.

This instruction sheet is for the following products:
7160-1265-00, (-P) & (-E) Docking Station- No RF, Keyed Alike
7160-1265-02, (-P) & (-E) Docking Station- Dual RF, Keyed Alike
7160-1265-04, (-P) & (-E) Docking Station- No RF, Keyed Different
7160-1265-06, (-P) & (-E) Docking Station- Dual RF, Keyed Different

Product Mounting Disclaimer

Product Mounting Disclaimer

Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage

Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage

of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson

of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson

products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is

products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is

required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications

required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications

and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.

and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.

© Copyright 2018 Gamber-Johnson, LLC

If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868

Page 1/8

PRE-INSTALLATION RECOMMENDATOINS

Conduct a "Bench Test"

Gamber-Johnson strongly advises a "bench test" be conducted to verify all electronic and
software issues are resolved prior to installation:

Make sure the computer is operational by itself.

1.
Insert computer into the docking station and verify that the computer is

2.
operating in the dock.
Interconnect entire assembly and verify start-up of all components, including

3.
other equipment (printers, modems, scanners, etc.)

Gamber-Johnson recommends positioning of all mounts and equipment in the vehicle
prior to the actual install to verify that mounting locations are safe and practical.

IMPORTANT SAFETY INFORMATION FOR INSTALLERS

Safety is dependent on the proper installation and servicing of this docking station. It is important to
read and follow all instructions before installing this product.

To properly install a Gamber-Johnson docking station you must have a good understanding of
automotive electrical procedures and systems, along with proficiency in the installation and service of
aftermarket vehicle equipment.

There are no adjustments required at any time of the electrical components within the docking station.

Opening the docking station will void the product warranty.

During Installation:

DO NOT

DO NOT

When drilling into the vehicle, DO make sure that both sides of the surface are clear of anything that
could be damaged.

CAUTION:

connect this docking station to the vehicle battery until:

All other electrical connections are made

1.
Mounting of all components is complete

2.
Verification that no shorts exist in the entire system

3.

install equipment or route wiring or cords in the deployment path of any air bag.

If wiring is shorted to the frame, high current conductors can cause hazardous sparks

resulting in electrical fires or flying molten metal.

After installation:

Test the docking station to ensure that it is working properly.

File these instructions in a safe place and refer to them when performing maintenance or re­installing.

WARNING

: Failure to follow all safety precautions and instructions may result in property damage,

serious injury, or death.

Page 2/8

PRECAUTIONS FOR OPERATING THE DOCKING STATION

Do Not Connect a Telephone Line, or

If a Malfunction or Trouble Occurs,

•
Immediately Stop Use

If a Malfunction Occurs, Immediately
Unplug the Car Plug and Remove the
Computer from this product

• This product is damaged

• The connector pins are bent

• A foreign object is inside this product

• Smoke is emitted

• An unusual smell is emitted

• Unusually hot
Continuing to use this product while any
of the above conditions are present may
result in fire or electric shock.

• If a malfunction or trouble occurs,
immediately unplug the car plug and
remove the unit from this product. Then,
contact your technical support office for
repair.

Do Not Touch This Product or Cable

•
When It Starts Thundering
Electric shock may result.

Do Not Place Containers of Liquid or

•
Metal Objects on Top of This Product If
water or other liquid spills, or if paper
clips, coins, or foreign matter get inside
this product, fire or electric shock may
result.

• If foreign matter has found its way
inside, immediately unplug the car plug
and remove the unit from this product.
Then contact your technical support
office.

Avoid a Lot of Water, Moisture, Steam,

•
Dust, Oily Vapors, etc.
Otherwise, possibly resulting in fire or
electric shock.

•
a Network Cable Other Than the one
Specified, Into the LAN Port.
If the LAN port is connected to a
network such as the ones listed below,
a fire or electric shock may result.

• Networks other than 1000BASE-T,
100BASE-TX or 10BASE-T

• Phone lines (IP phone (Internet
Protocol Telephone), Telephone lines,
internal phone lines (on premise
switches), digital public phones, etc.)

Using this product continuously in a

•
hot environment will shorten the
product life. Avoid use in these types
of environments.

When using in hot or cold

•
environment, some peripherals may
fail to work properly. Check the
operation environment of the
peripherals.

Do Not Install This Product in

•
Unstable State
If balance of the unit is lost, it may fall
over or drop, resulting in an injury.

Docks used in the vertical (Tablet)

•
position must be installed with the lock
on TOP. Installing the dock upside
down may result in damage to the
computer.

Do Not Install This Product Where

•
There is a Lot of Water, Moisture,
Steam, Dust, Oily Vapors, etc.
Otherwise, a possibility of fire or
electric shock could result.

Use Only the Specified Docking Station

•
with This Product
Using a Docking Station other than the
one supplied (supplied with the unit or
one sold separately as an accessory)
may result in a fire.

Page 3/8

DIMENSIONAL DRAWING

Installation fixing 75mm VESA studs are provided in the areas indicated by
the arrows in the figure above.

Page 4/8

DOCKING AND UNDOCKING THE COMPUTER

DOCKING PROCEDURE

1. Ensure latch is in the "OPEN" Position

2. Extend the CF-20 handle to the "DEPLOYED" position then insert CF-20

3. Push the top of the CF-20 into the dock. The latch will move to the "Docked" position

4. To secure the tablet ensure it is in the closed position with the display latch engaged

then move the lower latch into the locked position

5. Push the CF-20 handle into the "STOWED" position

6. Push the lock to secure the device

NOTES:
Ensure latch is fully in the "Docked" position. It is recommended that the CF-20 is pushed into
the dock with two hands. For CF-20 fitted with Gadget option, it may be necessary to attach
the main unit in the forward direction only. Refer to device manual for further information.

NOTE:
Portions of your Docking Station may differ somewhat from the illustrations in the operating
instructions, but this should present no problems in actual use. Be sure to follow the operating
instructions when using your Docking Station.

Page 5/8

CF20 DOCKING STATION FEATURE IDENTIFICATON

Lever

Lock

VGA Port

Serial Port

Secondary Latch

Ethernet Port

(2) USB 3.0 Ports

HDMI Port

External wireless
Ch1: WWAN / EX. ANT 1

DC IN 16V, 4.06A

Antenna Switch

External wireless
Ch2: WWAN-GPS / EX. ANT 2

Page 6/8

SPECIFICATIONS

Item

Power Supply Input

Expansion Bus Connector

USB Port*

LAN Port

HDMI Port**

VGA Port

Serial Port

Physical Dimension [WxHxD]

Weight

DC 15.6V-16V Must use approved FCC/E-marked PSU

HDMI x 1 For exclusive use with HDMI standard

Mini Dsub 15-pin female (Analog interface)

290x277x75mm (11.42x10.91x2.95")

Description

24-Pin

USB 3.0 x 2

RJ-45 x 1

Dsub 9-pin male

2.28kg(5 lb)

* Does not guarantee operation of all USB and HDMI-compatible peripherals
** When connecting the HDMI compatible display, specifications such as maximum resolutions
available to output differ, depending on the specifications of the connected devices.
See the specifications of the connected device for details.

Page 7/8

REGULATORY CERTIFICATION INFORMATION

Regulatory Model #: 7160-1265

GJ Model #'s:
7160-1265-00, 7160-1265-00-E, 7160-1265-00-P
7160-1265-02, 7160-1265-02-E, 7160-1265-02-P
7160-1265-04, 7160-1265-04-E, 7160-1265-04-P
7160-1265-06, 7160-1265-06-E, 7160-1265-06-P

Descriptions: Dock-Panasonic CF20

Certifications:

EN 55032:2012 Class B

•
EN 50498:2010

•
EN 50581:2012

•
EN 62368-1

•

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions.
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.

Gamber-Johnson LLC

3001 Borham Ave.

Stevens Point, WI, 54481

USA

715-344-3482

8/8